Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
4.5
2.7
Journals
Applied Sciences
Special Issues
Editorial Board Members’ Collection Series: Dental and Biological Materials
share announcement

Editorial Board Members’ Collection Series: Dental and Biological Materials

A special issue of Applied Sciences (ISSN 2076-3417). This special issue belongs to the section "Applied Dentistry and Oral Sciences".

Deadline for manuscript submissions: 31 October 2024 | Viewed by 1987

Special Issue Editor

Dr. Mary Anne Melo

E-Mail Website
Guest Editor
Department of General Dentistry, University of Maryland School of Dentistry, 650 W. Baltimore St., Baltimore, MD 21201, USA
Interests: oral biofilm; dental materials; dental caries; biomaterials
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

We are pleased to announce a new Special Issue, entitled “Editorial Board Members’ Collection Series: Dental and Biological Materials”, which will be a collection of papers invited for publication by the Editorial Board Members.

This Special Issue aims to collect high-quality articles and the latest research results in the field of dental and biological materials and to provide a platform for networking and communication among scholars in the field of Oral Sciences. These materials include dental composites, nanocomposites, sealants, bonding agents, cements, etc. All papers will be fully open access upon publication after peer review.

Dr. Mary Anne Melo
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Applied Sciences is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2400 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Published Papers (2 papers)

Download All Papers
Order results
Result details
Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:

Research

11 pages, 1576 KiB  
Article
Opportunistic Pathogens Isolated from Peri-Implant and Periodontal Subgingival Plaque from Adjacent Teeth
by Ana Maísa Sá, José Manuel Mendes, António Sérgio Silva, Maria dos Prazeres Gonçalves, Mónica Cardoso and Cristina Coelho
Appl. Sci. 2023, 13(16), 9078; https://doi.org/10.3390/app13169078 - 09 Aug 2023
Cited by 1 | Viewed by 751
Abstract
Even though most studies consider strict anaerobe Gram-negative bacteria as the main factor associated with peri-implantitis, other studies have identified other microorganisms present in implants related to peri-implant disease that have the ability to reduce the effectiveness of treatment, such as Candida spp., [...] Read more.
Even though most studies consider strict anaerobe Gram-negative bacteria as the main factor associated with peri-implantitis, other studies have identified other microorganisms present in implants related to peri-implant disease that have the ability to reduce the effectiveness of treatment, such as Candida spp., Enterococcus faecalis and Pseudomonas aeruginosa. Therefore, microbiologic diagnosis is important for the success of implant treatment. The main goal of this study was to detect Candida spp., E. faecalis and P. aeruginosa in the peri-implant and periodontal subgingival plaque in the presence or absence of disease and to relate the presence of these microorganisms with demographic data, hygiene habits, the type of implant connection and endodontic treatment. The study population consisted of 20 patients that filled out a questionnaire regarding gender, age, systemic diseases and oral hygiene. The peri-implant and periodontal subgingival plaque from an adjacent tooth, both with and without disease, were analysed for the presence of these three opportunistic pathogens. Microbiological analysis revealed a higher prevalence of E. faecalis in patients with and without periodontal and peri-implant disease. Candida spp. was identified in a higher degree in cases with disease, and P. aeruginosa was mostly detected in peri-implantitis. The detection of these three pathogens suggested a possible means of transmission of infection from adjacent teeth to implants, with the implant design associated with rehabilitation being a primary cause of pathogen growth. Although this study did not relate pathogen growth directly to periodontal disease, the high colony forming unit per millilitre (CFU/mL) values of E. faecalis may reveal an aetiological role of this bacterium in peri-implantitis. Full article
(This article belongs to the Special Issue Editorial Board Members’ Collection Series: Dental and Biological Materials)
►▼ Show Figures

Figure 1

11 pages, 1337 KiB  
Article
In Vitro Investigation of the Mechanical Properties of Blended 3D-Printing Resins for Orthodontic Aligners: A Comparison between Commercial Resin and Nickel-Titanium Wire
by Piero Antonio Zecca, Salvatore Bocchieri, Marina Borgese, Carolina Dolci, Alessandra Campobasso, Giovanni Battista, Alberto Caprioglio and Mario Raspanti
Appl. Sci. 2023, 13(15), 9020; https://doi.org/10.3390/app13159020 - 07 Aug 2023
Viewed by 999
Abstract
This scientific article investigates the mechanical properties of a novel three-dimensional-printing resin specifically designed for orthodontic aligners and compares it to other commonly used resins. The resin was made by blending two commercially available and certified resins to produce aligners with improved mechanical [...] Read more.
This scientific article investigates the mechanical properties of a novel three-dimensional-printing resin specifically designed for orthodontic aligners and compares it to other commonly used resins. The resin was made by blending two commercially available and certified resins to produce aligners with improved mechanical properties compared to each separate resin. The study examined the effect of the addition of NextDent Ortho Rigid resin on the mechanical properties of the specimens, more specifically analyzing the relationship between the amount of the added rigid resin and the mechanical properties of the specimens. The mechanical properties of the specimens and the nickel-titanium wires were analyzed using a three-point bending test setup. The results showed no statistically significant differences within the different groups of specimens. The study provides valuable insights into the potential of the resin to meet the mechanical demands of orthodontic treatments. It will contribute to the advancement of personalized orthodontic care through three-dimensional-printing technology. Blending commercially available and certified resins enables orthodontic practitioners to select the most suitable resin for each case, providing better outcomes for patients and increasing the efficiency of the treatment process. Further research and evaluation would be required to determine the suitability of the blended resin for orthodontic treatments. Full article
(This article belongs to the Special Issue Editorial Board Members’ Collection Series: Dental and Biological Materials)
►▼ Show Figures

Figure 1

Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:
 
Displaying articles 1-2
Back to TopTop