Research

Jump to: Review

11062 KiB

Open AccessFeature PaperArticle

The In Vitro Bioactivity, Degradation, and Cytotoxicity of Polymer-Derived Wollastonite-Diopside Glass-Ceramics

by Amanda De Castro Juraski, Andrea Cecilia Dorion Rodas, Hamada Elsayed, Enrico Bernardo, Viviane Oliveira Soares and Juliana Daguano

Materials 2017, 10(4), 425; https://doi.org/10.3390/ma10040425 - 18 Apr 2017

Cited by 23 | Viewed by 6953

Abstract

Ca-Mg silicates are receiving a growing interest in the field of bioceramics. In a previous study, wollastonite-diopside (WD) glass-ceramics were successfully prepared by a new processing route, consisting of the heat treatment of a silicone resin embedding reactive oxide particles and a Ca/Mg-rich [...] Read more.

Ca-Mg silicates are receiving a growing interest in the field of bioceramics. In a previous study, wollastonite-diopside (WD) glass-ceramics were successfully prepared by a new processing route, consisting of the heat treatment of a silicone resin embedding reactive oxide particles and a Ca/Mg-rich glass. The in vitro degradation, bioactivity, and cell response of these new WD glass-ceramics, fired at 900–1100 °C for 1 h, as a function of the Ca/Mg-rich glass content, are the aim of this investigation The results showed that WD glass-ceramics from formulations comprising different glass contents (70–100% at 900 °C, 30% at 1100 °C) exhibit the formation of an apatite-like layer on their surface after immersion in SBF for seven days, thus confirming their surface bioactivity. The XRD results showed that these samples crystallized, mainly forming wollastonite (CaSiO₃) and diopside (CaMgSi₂O₆), but combeite (Na₂Ca₂Si₃O₉) crystalline phase was also detected. Besides in vitro bioactivity, cytotoxicity and osteoblast adhesion and proliferation tests were applied after all characterizations, and the formulation comprising 70% glass was demonstrated to be promising for further in vivo studies. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

3069 KiB

Open AccessArticle

Fabrication of Carbonate Apatite Block through a Dissolution–Precipitation Reaction Using Calcium Hydrogen Phosphate Dihydrate Block as a Precursor

by Kanji Tsuru, Ayami Yoshimoto, Masayuki Kanazawa, Yuki Sugiura, Yasuharu Nakashima and Kunio Ishikawa

Materials 2017, 10(4), 374; https://doi.org/10.3390/ma10040374 - 31 Mar 2017

Cited by 35 | Viewed by 4725

Abstract

Carbonate apatite (CO₃Ap) block, which is a bone replacement used to repair defects, was fabricated through a dissolution–precipitation reaction using a calcium hydrogen phosphate dihydrate (DCPD) block as a precursor. When the DCPD block was immersed in NaHCO₃ or Na [...] Read more.

Carbonate apatite (CO₃Ap) block, which is a bone replacement used to repair defects, was fabricated through a dissolution–precipitation reaction using a calcium hydrogen phosphate dihydrate (DCPD) block as a precursor. When the DCPD block was immersed in NaHCO₃ or Na₂CO₃ solution at 80 °C, DCPD converted to CO₃Ap within 3 days. β-Tricalcium phosphate was formed as an intermediate phase, and it was completely converted to CO₃Ap within 2 weeks when the DCPD block was immersed in Na₂CO₃ solution. Although the crystal structures of the DCPD and CO₃Ap blocks were different, the macroscopic structure was maintained during the compositional transformation through the dissolution–precipitation reaction. CO₃Ap block fabricated in NaHCO₃ or Na₂CO₃ solution contained 12.9 and 15.8 wt % carbonate, respectively. The diametral tensile strength of the CO₃Ap block was 2 MPa, and the porosity was approximately 57% regardless of the carbonate solution. DCPD is a useful precursor for the fabrication of CO₃Ap block. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

3367 KiB

Open AccessArticle

Fabrication of Biocompatible Potassium Sodium Niobate Piezoelectric Ceramic as an Electroactive Implant

by Wei Chen, Zunxiong Yu, Jinshan Pang, Peng Yu, Guoxin Tan and Chengyun Ning

Materials 2017, 10(4), 345; https://doi.org/10.3390/ma10040345 - 26 Mar 2017

Cited by 70 | Viewed by 7143

Abstract

The discovery of piezoelectricity in natural bone has attracted extensive research in emulating biological electricity for various tissue regeneration. Here, we carried out experiments to build biocompatible potassium sodium niobate (KNN) ceramics. Then, influence substrate surface charges on bovine serum albumin (BSA) protein [...] Read more.

The discovery of piezoelectricity in natural bone has attracted extensive research in emulating biological electricity for various tissue regeneration. Here, we carried out experiments to build biocompatible potassium sodium niobate (KNN) ceramics. Then, influence substrate surface charges on bovine serum albumin (BSA) protein adsorption and cell proliferation on KNN ceramics surfaces was investigated. KNN ceramics with piezoelectric constant of ~93 pC/N and relative density of ~93% were fabricated. The adsorption of protein on the positive surfaces (Ps) and negative surfaces (Ns) of KNN ceramics with piezoelectric constant of ~93 pC/N showed greater protein adsorption capacity than that on non-polarized surfaces (NPs). Biocompatibility of KNN ceramics was verified through cell culturing and live/dead cell staining of MC3T3. The cells experiment showed enhanced cell growth on the positive surfaces (Ps) and negative surfaces (Ns) compared to non-polarized surfaces (NPs). These results revealed that KNN ceramics had great potential to be used to understand the effect of surface potential on cells processes and would benefit future research in designing piezoelectric materials for tissue regeneration. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Graphical abstract

1225 KiB

Open AccessArticle

In Vitro Evaluation of Dentin Tubule Occlusion for Novel Calcium Lactate Phosphate (CLP) Paste

by Jen-Chang Yang, Hsin-Tai Hu, Sheng-Yang Lee, Sung-Chih Hsieh, Pei-Chi Huang, Chen-Feng Ma, Dian-Yu Ji, Liang-Yu Chang and Nai-Chia Teng

Materials 2017, 10(3), 228; https://doi.org/10.3390/ma10030228 - 27 Feb 2017

Cited by 3 | Viewed by 4547

Abstract

Introduction: The objective of this in vitro study is to evaluate the effective and long-term occlusion of dentinal tubules using a novel calcium lactate phosphate (CLP) based desensitizing agent. Methods: Dentin disks (n = 9) were pre-etched using 1 M lactic acid for [...] Read more.

Introduction: The objective of this in vitro study is to evaluate the effective and long-term occlusion of dentinal tubules using a novel calcium lactate phosphate (CLP) based desensitizing agent. Methods: Dentin disks (n = 9) were pre-etched using 1 M lactic acid for 30 s and individually treated with Colgate^® Pro-Relief™ paste, CLP paste, and double distilled water (ddH₂O) by a rubber-cupped handpiece. Dentin disks were analyzed under optical micrographs for pre-treatment, directly after treatment, and 14 days post-treatment. One-way ANOVA and post-hoc Tukey’s test were used to determine whether there were any statistically significant differences in dentinal tubule diameter. Results: A significant decrease occurred in the mean tubule diameter for dentin disks treated with CLP paste. A decrease was observed from 3.52 ± 0.83 µm to 2.62 ± 0.42 µm right after treatment, further decreasing to 1.71 ± 0.45 µm after immersion in artificial saliva for 14 days (p < 0.05). Conclusions: The results suggest that the CLP based desensitizing paste has remineralization properties and provides instant and lasting effectiveness in dentinal tubule occlusion. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

5607 KiB

Open AccessFeature PaperArticle

Bioactive Glass-Ceramic Scaffolds from Novel ‘Inorganic Gel Casting’ and Sinter-Crystallization

by Hamada Elsayed, Acacio Rincón Romero, Letizia Ferroni, Chiara Gardin, Barbara Zavan and Enrico Bernardo

Materials 2017, 10(2), 171; https://doi.org/10.3390/ma10020171 - 13 Feb 2017

Cited by 37 | Viewed by 6461

Abstract

Highly porous wollastonite-diopside glass-ceramics have been successfully obtained by a new gel-casting technique. The gelation of an aqueous slurry of glass powders was not achieved according to the polymerization of an organic monomer, but as the result of alkali activation. The alkali activation [...] Read more.

Highly porous wollastonite-diopside glass-ceramics have been successfully obtained by a new gel-casting technique. The gelation of an aqueous slurry of glass powders was not achieved according to the polymerization of an organic monomer, but as the result of alkali activation. The alkali activation of a Ca-Mg silicate glass (with a composition close to 50 mol % wollastonite—50 mol % diopside, with minor amounts of Na₂O and P₂O₅) allowed for the obtainment of well-dispersed concentrated suspensions, undergoing progressive hardening by curing at low temperature (40 °C), owing to the formation of a C–S–H (calcium silicate hydrate) gel. An extensive direct foaming was achieved by vigorous mechanical stirring of partially gelified suspensions, comprising also a surfactant. The open-celled structure resulting from mechanical foaming could be ‘frozen’ by the subsequent sintering treatment, at 900–1000 °C, causing substantial crystallization. A total porosity exceeding 80%, comprising both well-interconnected macro-pores and micro-pores on cell walls, was accompanied by an excellent compressive strength, even above 5 MPa. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

3813 KiB

Open AccessArticle

Effect of the Medium Composition on the Zn²⁺ Lixiviation and the Antifouling Properties of a Glass with a High ZnO Content

by Leticia Esteban-Tejeda, Francisco J. Palomares, Belén Cabal, Roberto López-Píriz, Adolfo Fernández, David Sevillano, Luis Alou, Ramón Torrecillas and José S. Moya

Materials 2017, 10(2), 167; https://doi.org/10.3390/ma10020167 - 13 Feb 2017

Cited by 5 | Viewed by 4030

Abstract

The dissolution of an antimicrobial ZnO-glass in the form of powder and in the form of sintered pellets were studied in water, artificial seawater, biological complex media such as common bacterial/yeast growth media (Luria Bertani (LB), yeast extract, tryptone), and human serum. It [...] Read more.

The dissolution of an antimicrobial ZnO-glass in the form of powder and in the form of sintered pellets were studied in water, artificial seawater, biological complex media such as common bacterial/yeast growth media (Luria Bertani (LB), yeast extract, tryptone), and human serum. It has been established that the media containing amino acids and proteins produce a high lixiviation of Zn²⁺ from the glass due to the ability of zinc and zinc oxide to react with amino acids and proteins to form complex organic compounds. The process of Zn²⁺ lixiviation from the glass network has been studied by X-ray photoelectron spectroscopy (XPS). From these results we can state that the process of lixiviation of Zn²⁺ from the glass network is similar to the one observed in sodalime glasses, where Na⁺ is lixiviated to the media first and the fraction of Zn that acts as modifiers (~2/3) is lixiviated in second place. After the subsequent collapse of the outer surface glass layer (about 200–300 nm thick layer) the dissolution process starts again. Antifouling properties against different bacteria (S. epidermidis, S. aureus, P. aeruginosa, E. coli, and M. lutea) have also been established for the glass pellets. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

6716 KiB

Open AccessFeature PaperArticle

Bioactive Glass Fiber-Reinforced PGS Matrix Composites for Cartilage Regeneration

by Marina Trevelin Souza, Samira Tansaz, Edgar Dutra Zanotto and Aldo R. Boccaccini

Materials 2017, 10(1), 83; https://doi.org/10.3390/ma10010083 - 20 Jan 2017

Cited by 38 | Viewed by 6965

Abstract

Poly(glycerol sebacate) (PGS) is an elastomeric polymer which is attracting increasing interest for biomedical applications, including cartilage regeneration. However, its limited mechanical properties and possible negative effects of its degradation byproducts restrict PGS for in vivo application. In this study, a novel PGS–bioactive [...] Read more.

Poly(glycerol sebacate) (PGS) is an elastomeric polymer which is attracting increasing interest for biomedical applications, including cartilage regeneration. However, its limited mechanical properties and possible negative effects of its degradation byproducts restrict PGS for in vivo application. In this study, a novel PGS–bioactive glass fiber (F18)-reinforced composite was developed and characterized. PGS-based reinforced scaffolds were fabricated via salt leaching and characterized regarding their mechanical properties, degradation, and bioactivity in contact with simulated body fluid. Results indicated that the incorporation of silicate-based bioactive glass fibers could double the composite tensile strength, tailor the polymer degradability, and improve the scaffold bioactivity. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Graphical abstract

13788 KiB

Open AccessArticle

Physico-Chemical, In Vitro, and In Vivo Evaluation of a 3D Unidirectional Porous Hydroxyapatite Scaffold for Bone Regeneration

by Manabu Tanaka, Hisao Haniu, Takayuki Kamanaka, Takashi Takizawa, Atsushi Sobajima, Kazushige Yoshida, Kaoru Aoki, Masanori Okamoto, Hiroyuki Kato and Naoto Saito

Materials 2017, 10(1), 33; https://doi.org/10.3390/ma10010033 - 03 Jan 2017

Cited by 28 | Viewed by 6637

Abstract

The unidirectional porous hydroxyapatite HAp (UDPHAp) is a scaffold with continuous communicated pore structure in the axial direction. We evaluated and compared the ability of the UDPHAp as a three-dimensional (3D) bone tissue engineering scaffold to the interconnected calcium porous HAp ceramic (IP-CHA). [...] Read more.

The unidirectional porous hydroxyapatite HAp (UDPHAp) is a scaffold with continuous communicated pore structure in the axial direction. We evaluated and compared the ability of the UDPHAp as a three-dimensional (3D) bone tissue engineering scaffold to the interconnected calcium porous HAp ceramic (IP-CHA). To achieve this, we evaluated in vitro the compressive strength, controlled rhBMP-2 release behavior, adherent cell morphology, cell adhesion manner, and cell attachment of UDPHAp. As a further in vivo experiment, UDPHAp and IP-CHA with rhBMP-2 were transplanted into mouse calvarial defects to evaluate their bone-forming ability. The Results demonstrated that the maximum compressive strengths of the UDPHAp was 7.89 ± 1.23 MPa and higher than that of IP-CHA (1.92 ± 0.53 MPa) (p = 0.0039). However, the breaking energies were similar (8.99 ± 2.72 vs. 13.95 ± 5.69 mJ, p = 0.055). The UDPHAp released rhBMP-2 more gradually in vivo. Cells on the UDPHAp adhered tightly to the surface, which had grown deeply into the scaffolds. A significant increase in cell number on the UDPHAp was observed compared to the IP-CHA on day 8 (102,479 ± 34,391 vs. 32,372 ± 29,061 estimated cells per scaffold, p = 0.0495). In a mouse calvarial defect model, the percentages of new bone area (mature bone + trabecular bone) in the 2x field were 2.514% ± 1.224% for the IP-CHA group and 7.045% ± 2.055% for the UDPHAp group, and the percentage was significantly higher in the UDPHAp group (p = 0.0209). While maintaining the same strength as the IP-CHA, the UDPHAp with 84% porosity showed a high cell number, high cell invasiveness, and excellent bone formation. We believe the UDPHAp is an excellent material that can be applied to bone regenerative medicine. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Graphical abstract

3864 KiB

Open AccessArticle

Assessment of Effects of Si-Ca-P Biphasic Ceramic on the Osteogenic Differentiation of a Population of Multipotent Adult Human Stem Cells

by Patricia Ros-Tárraga, Rubén Rabadan-Ros, Angel Murciano, Luis Meseguer-Olmo and Piedad N. De Aza

Materials 2016, 9(12), 969; https://doi.org/10.3390/ma9120969 - 29 Nov 2016

Cited by 9 | Viewed by 4803

Abstract

A new type of bioceramic with osteogenic properties, suitable for hard tissue regeneration, was synthesised. The ceramic was designed and obtained in the Nurse’s A-phase-silicocarnotite subsystem. The selected composition was that corresponding to the eutectoid 28.39 wt % Nurse’s A-phase-71.61 wt % silicocarnotite [...] Read more.

A new type of bioceramic with osteogenic properties, suitable for hard tissue regeneration, was synthesised. The ceramic was designed and obtained in the Nurse’s A-phase-silicocarnotite subsystem. The selected composition was that corresponding to the eutectoid 28.39 wt % Nurse’s A-phase-71.61 wt % silicocarnotite invariant point. We report the effect of Nurse’s A-phase-silicocarnotite ceramic on the capacity of multipotent adult human mesenchymal stem cells (ahMSCs) cultured under experimental conditions, known to adhere, proliferate and differentiate into osteoblast lineage cells. The results at long-term culture (28 days) on the material confirmed that the undifferentiated ahMSCs cultured and in contact with the material surface adhered, spread, proliferated, and produced a mineralised extracellular matrix on the studied ceramic, and finally acquired an osteoblastic phenotype. These findings indicate that it underwent an osteoblast differentiation process. All these findings were more significant than when cells were grown on plastic, in the presence and absence of this osteogenic supplement, and were more evident when this supplement was present in the growth medium (GM). The ceramic evaluated herein was bioactive, cytocompatible and capable of promoting the proliferation and differentiation of undifferentiated ahMSCs into osteoblasts, which may be important for bone integration into the clinical setting. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

5872 KiB

Open AccessArticle

Synthesis and In Vitro Activity Assessment of Novel Silicon Oxycarbide-Based Bioactive Glasses

by Isabel Gonzalo-Juan, Rainer Detsch, Sanjay Mathur, Emanuel Ionescu, Aldo R. Boccaccini and Ralf Riedel

Materials 2016, 9(12), 959; https://doi.org/10.3390/ma9120959 - 24 Nov 2016

Cited by 32 | Viewed by 6545

Abstract

Novel bioactive glasses based on a Ca- and Mg-modified silicon oxycarbide (SiCaMgOC) were prepared from a polymeric single-source precursor, and their in vitro activity towards hydroxyapatite mineralization was investigated upon incubating the samples in simulated body fluid (SBF) at 37 °C. The as-prepared [...] Read more.

Novel bioactive glasses based on a Ca- and Mg-modified silicon oxycarbide (SiCaMgOC) were prepared from a polymeric single-source precursor, and their in vitro activity towards hydroxyapatite mineralization was investigated upon incubating the samples in simulated body fluid (SBF) at 37 °C. The as-prepared materials exhibit an outstanding resistance against devitrification processes and maintain their amorphous nature even after exposure to 1300 °C. The X-ray diffraction (XRD) analysis of the SiCaMgOC samples after the SBF test showed characteristic reflections of apatite after only three days, indicating a promising bioactivity. The release kinetics of the Ca²⁺ and Mg²⁺ and the adsorption of H⁺ after immersion of SiCaMgOC in simulated body fluid for different soaking times were analyzed via optical emission spectroscopy. The results show that the mechanism of formation of apatite on the surface of the SiCaMgOC powders is similar to that observed for standard (silicate) bioactive glasses. A preliminary cytotoxicity investigation of the SiOC-based bioactive glasses was performed in the presence of mouse embryonic fibroblasts (MEF) as well as human embryonic kidney cells (HEK-293). Due to their excellent high-temperature crystallization resistance in addition to bioactivity, the Ca- and Mg-modified SiOC glasses presented here might have high potential in applications related to bone repair and regeneration. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

9686 KiB

Open AccessArticle

Evaluation of the Antimicrobial Activity of Different Antibiotics Enhanced with Silver-Doped Hydroxyapatite Thin Films

by Daniela Predoi, Cristina Liana Popa, Patrick Chapon, Andreea Groza and Simona Liliana Iconaru

Materials 2016, 9(9), 778; https://doi.org/10.3390/ma9090778 - 16 Sep 2016

Cited by 31 | Viewed by 6857

Abstract

The inhibitory and antimicrobial effects of silver particles have been known since ancient times. In the last few years, a major health problem has arisen due to pathogenic bacteria resistance to antimicrobial agents. The antibacterial activities of new materials including hydroxyapatite (HAp), silver-doped [...] Read more.

The inhibitory and antimicrobial effects of silver particles have been known since ancient times. In the last few years, a major health problem has arisen due to pathogenic bacteria resistance to antimicrobial agents. The antibacterial activities of new materials including hydroxyapatite (HAp), silver-doped hydroxyapatite (Ag:HAp) and various types of antibiotics such as tetracycline (T-HAp and T-Ag:HAp) or ciprofloxacin (C-HAp and C-Ag:HAp) have not been studied so far. In this study we reported, for the first time, the preparation and characterization of various thin films based on hydroxyapatite and silver-doped hydroxyapatite combined with tetracycline or ciprofloxacin. The structural and chemical characterization of hydroxyapatite and silver-doped hydroxyapatite thin films has been evaluated by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The morphological studies of the HAp, Ag:HAp, T-HAp, T-Ag:HAp, C-HAp and C-Ag:HAp thin solid films were performed using scanning electron microscopy (SEM). In order to study the chemical composition of the coatings, energy dispersive X-ray analysis (EDX) and glow discharge optical emission spectroscopy (GDOES) measurements have been used, obtaining information on the distribution of the elements throughout the film. These studies have confirmed the purity of the prepared hydroxyapatite and silver-doped hydroxyapatite thin films obtained from composite targets containing Ca_10−xAg_x(PO₄)₆(OH)₂ with x_Ag = 0 (HAp) and x_Ag = 0.2 (Ag:HAp). On the other hand, the major aim of this study was the evaluation of the antibacterial activities of ciprofloxacin and tetracycline in the presence of HAp and Ag:HAp thin layers against Staphylococcus aureus and Escherichia coli strains. The antibacterial activities of ciprofloxacin and tetracycline against Staphylococcus aureus and Escherichia coli test strains increased in the presence of HAp and Ag:HAp thin layers. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Graphical abstract

5270 KiB

Open AccessArticle

Novel Osteointegrative Sr-Substituted Apatitic Cements Enriched with Alginate

by Simone Sprio, Massimiliano Dapporto, Monica Montesi, Silvia Panseri, Wanda Lattanzi, Enrico Pola, Giandomenico Logroscino and Anna Tampieri

Materials 2016, 9(9), 763; https://doi.org/10.3390/ma9090763 - 08 Sep 2016

Cited by 22 | Viewed by 4304

Abstract

The present work describes the synthesis of novel injectable, self-setting bone cements made of strontium-substituted hydroxyapatite (Sr-HA), obtained by single-phase calcium phosphate precursors doped with different amounts of strontium and enriched with alginate. The addition of alginate improved the injectability, cohesion, and compression [...] Read more.

The present work describes the synthesis of novel injectable, self-setting bone cements made of strontium-substituted hydroxyapatite (Sr-HA), obtained by single-phase calcium phosphate precursors doped with different amounts of strontium and enriched with alginate. The addition of alginate improved the injectability, cohesion, and compression strength of the cements, without affecting the hardening process. A Sr-HA cement exhibiting adequate hardening times and mechanical strength for clinical applications was further tested in vivo in a rabbit model, in comparison with a commercial calcium phosphate cement, revealing the maintenance of biomimetic composition and porous microstructure even after one month in vivo, as well as enhanced ability to induce new bone formation and penetration. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

5840 KiB

Open AccessArticle

Preparation of Nanofibrous Structure of Mesoporous Bioactive Glass Microbeads for Biomedical Applications

by Shiao-Wen Tsai, Yu-Han Chang, Jing-Lun Yu, Hsien-Wen Hsu, Lih-Rou Rau and Fu-Yin Hsu

Materials 2016, 9(6), 487; https://doi.org/10.3390/ma9060487 - 17 Jun 2016

Cited by 16 | Viewed by 6529

Abstract

A highly ordered, mesoporous (pore size 2~50 nm) bioactive glass (MBG) structure has a greater surface area and pore volume and excellent bone-forming bioactivity compared with traditional bioactive glasses (BGs). Hence, MBGs have been used in drug delivery and bone tissue engineering. MBGs [...] Read more.

A highly ordered, mesoporous (pore size 2~50 nm) bioactive glass (MBG) structure has a greater surface area and pore volume and excellent bone-forming bioactivity compared with traditional bioactive glasses (BGs). Hence, MBGs have been used in drug delivery and bone tissue engineering. MBGs can be developed as either a dense or porous block. Compared with a block, microbeads provide greater flexibility for filling different-shaped cavities and are suitable for culturing cells in vitro. In contrast, the fibrous structure of a scaffold has been shown to increase cell attachment and differentiation due to its ability to mimic the three-dimensional structure of natural extracellular matrices. Hence, the aim of this study is to fabricate MBG microbeads with a fibrous structure. First, a sol-gel/electrospinning technique was utilized to fabricate the MBG nanofiber (MBGNF) structure. Subsequently, the MBGNF microbeads (MFBs) were produced by an electrospraying technology. The results show that the diameter of the MFBs decreases when the applied voltage increases. The drug loading and release profiles and mechanisms of the MFBs were also evaluated. MFBs had a better drug entrapment efficiency, could reduce the burst release of tetracycline, and sustain the release over 10 days. Hence, the MFBs may be suitable drug carriers. In addition, the cellular attachment of MG63 osteoblast-like cells is significantly higher for MFBs than for glass microbeads after culturing for 4 h. The nanofibrous structure of MFBs could provide an appropriate environment for cellular spreading. Therefore, MFBs have great potential for use as a bone graft material in bone tissue engineering applications. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

Review

Jump to: Research

5447 KiB

Open AccessReview

Doped Calcium Silicate Ceramics: A New Class of Candidates for Synthetic Bone Substitutes

by Young Jung No, Jiao Jiao Li and Hala Zreiqat

Materials 2017, 10(2), 153; https://doi.org/10.3390/ma10020153 - 10 Feb 2017

Cited by 81 | Viewed by 8537

Abstract

Doped calcium silicate ceramics (DCSCs) have recently gained immense interest as a new class of candidates for the treatment of bone defects. Although calcium phosphates and bioactive glasses have remained the mainstream of ceramic bone substitutes, their clinical use is limited by suboptimal [...] Read more.

Doped calcium silicate ceramics (DCSCs) have recently gained immense interest as a new class of candidates for the treatment of bone defects. Although calcium phosphates and bioactive glasses have remained the mainstream of ceramic bone substitutes, their clinical use is limited by suboptimal mechanical properties. DCSCs are a class of calcium silicate ceramics which are developed through the ionic substitution of calcium ions, the incorporation of metal oxides into the base binary xCaO–ySiO₂ system, or a combination of both. Due to their unique compositions and ability to release bioactive ions, DCSCs exhibit enhanced mechanical and biological properties. Such characteristics offer significant advantages over existing ceramic bone substitutes, and underline the future potential of adopting DCSCs for clinical use in bone reconstruction to produce improved outcomes. This review will discuss the effects of different dopant elements and oxides on the characteristics of DCSCs for applications in bone repair, including mechanical properties, degradation and ion release characteristics, radiopacity, and biological activity (in vitro and in vivo). Recent advances in the development of DCSCs for broader clinical applications will also be discussed, including DCSC composites, coated DCSC scaffolds and DCSC-coated metal implants. Full article

(This article belongs to the Special Issue Bioceramics 2016)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Bioceramics 2016

Share This Special Issue

Special Issue Editor

Special Issue Information

Keywords

Published Papers (14 papers)

Research

Review

Further Information

Guidelines

MDPI Initiatives

Follow MDPI