Materials

Research

19 pages, 20611 KiB

Open AccessArticle

Vibratory Powder Feeding for Powder Bed Additive Manufacturing Using Water and Gas Atomized Metal Powders

by Chad W. Sinclair, Ralf Edinger, Will Sparling, Amin Molavi-Kakhki and Chantal Labrecque

Materials 2021, 14(13), 3548; https://doi.org/10.3390/ma14133548 - 25 Jun 2021

Cited by 8 | Viewed by 2407

Commercial powder bed fusion additive manufacturing systems use re-coaters for the layer-by-layer distribution of powder. Despite the known limitations of re-coaters, there has been relatively little work presented on the possible benefits of alternative powder delivery systems. Here, we reveal a feeding technology [...] Read more.

Commercial powder bed fusion additive manufacturing systems use re-coaters for the layer-by-layer distribution of powder. Despite the known limitations of re-coaters, there has been relatively little work presented on the possible benefits of alternative powder delivery systems. Here, we reveal a feeding technology that uses vibration to control flow for powder bed additive manufacturing. The capabilities of this approach are illustrated experimentally using two very different powders; a ‘conventional’ gas atomized Ti-6Al-4V powder designed for electron beam additive manufacturing and a water atomized Fe-4 wt.% Ni alloy used in powder metallurgy. Single layer melt trials are shown for the water atomized powder to illustrate the fidelity of the melt tracks in this material. Discrete element modelling is next used to reveal the mechanisms that underpin the observed dependence of feed rate on feeder process parameters and to investigate the potential strengths and limitations of this feeding methodology. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Figure 1

13 pages, 2629 KiB

Open AccessArticle

Microstructures and Mechanical Properties of Hybrid, Additively Manufactured Ti6Al4V after Thermomechanical Processing

by Susanne Hemes, Frank Meiners, Irina Sizova, Rebar Hama-Saleh, Daniel Röhrens, Andreas Weisheit, Constantin Leon Häfner and Markus Bambach

Materials 2021, 14(4), 1039; https://doi.org/10.3390/ma14041039 - 22 Feb 2021

Cited by 5 | Viewed by 2742

Abstract

In the present study, we propose a hybrid manufacturing route to produce high-quality Ti6Al4V parts, combining additive powder laser directed energy deposition (L-DED) for manufacturing of preforms, with subsequent hot forging as a thermomechanical processing (TMP) step. After L-DED, the material was hot [...] Read more.

In the present study, we propose a hybrid manufacturing route to produce high-quality Ti6Al4V parts, combining additive powder laser directed energy deposition (L-DED) for manufacturing of preforms, with subsequent hot forging as a thermomechanical processing (TMP) step. After L-DED, the material was hot formed at two different temperatures (930 °C and 1070 °C) and subsequently heat-treated for stress relief annealing. Tensile tests were performed on small sub-samples, taking into account different sample orientations with respect to the L-DED build direction and resulting in very good tensile strengths and ductility properties, similar or superior to the forged material. The resulting microstructure consists of very fine grained, partially globularized alpha grains, with a mean diameter ~0.8–2.3 µm, within a beta phase matrix, constituting between 2 and 9% of the sample. After forging in the sub-beta transus temperature range, the typical L-DED microstructure was no longer discernible and the anisotropy in tensile properties, common in additive manufacturing (AM), was significantly reduced. However, forging in the super-beta transus temperature range resulted in remaining anisotropies in the mechanical properties as well as an inferior tensile strength and ductility of the material. It was shown, that by combining L-DED with thermomechanical processing in the sub-beta transus temperature range of Ti6Al4V, a suitable microstructure and desirable mechanical properties for many applications can be obtained, with the advantage of reducing the material waste. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Figure 1

8 pages, 3358 KiB

Open AccessCommunication

Epitaxial Growth of Silicon on Silicon Wafers by Direct Laser Melting

by Marie Le Dantec, Mustafa Abdulstaar, Marc Leparoux and Patrik Hoffmann

Materials 2020, 13(21), 4728; https://doi.org/10.3390/ma13214728 - 23 Oct 2020

Cited by 6 | Viewed by 2150

Abstract

Additive manufacturing (AM) of brittle materials remains challenging, as they are prone to cracking due to the steep thermal gradients present during melting and cooling after laser exposition. Silicon is an ideal brittle material for study since most of the physical properties of [...] Read more.

Additive manufacturing (AM) of brittle materials remains challenging, as they are prone to cracking due to the steep thermal gradients present during melting and cooling after laser exposition. Silicon is an ideal brittle material for study since most of the physical properties of single-element materials can be found in the literature and high-purity silicon powders are readily available. Direct laser melting (DLM) of silicon powder was performed to establish the conditions under which cracks occur and to understand how the solidification front impacts the final microstructure. Through careful control of process conditions, paying special attention to thermal gradients and the growth velocity, epitaxial pillars free of cracks could be grown to a length of several millimeters. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Figure 1

22 pages, 9342 KiB

Open AccessArticle

Pyrometric-Based Melt Pool Monitoring Study of CuCr1Zr Processed Using L-PBF

by Katia Artzt, Martin Siggel, Jan Kleinert, Joerg Riccius, Guillermo Requena and Jan Haubrich

Materials 2020, 13(20), 4626; https://doi.org/10.3390/ma13204626 - 16 Oct 2020

Cited by 13 | Viewed by 2112

Abstract

The potential of in situ melt pool monitoring (MPM) for parameter development and furthering the process understanding in Laser Powder Bed Fusion (LPBF) of CuCr1Zr was investigated. Commercial MPM systems are currently being developed as a quality monitoring tool with the aim of [...] Read more.

The potential of in situ melt pool monitoring (MPM) for parameter development and furthering the process understanding in Laser Powder Bed Fusion (LPBF) of CuCr1Zr was investigated. Commercial MPM systems are currently being developed as a quality monitoring tool with the aim of detecting faulty parts already in the build process and, thus, reducing costs in LPBF. A detailed analysis of coupon specimens allowed two processing windows to be established for a suitably dense material at layer thicknesses of 30 µm and 50 µm, which were subsequently evaluated with two complex thermomechanical-fatigue (TMF) panels. Variations due to the location on the build platform were taken into account for the parameter development. Importantly, integrally averaged MPM intensities showed no direct correlation with total porosities, while the robustness of the melting process, impacted strongly by balling, affected the scattering of the MPM response and can thus be assessed. However, the MPM results, similar to material properties such as porosity, cannot be directly transferred from coupon specimens to components due to the influence of the local part geometry and heat transport on the build platform. Different MPM intensity ranges are obtained on cuboids and TMF panels despite similar LPBF parameters. Nonetheless, besides identifying LPBF parameter windows with a stable process, MPM allowed the successful detection of individual defects on the surface and in the bulk of the large demonstrators and appears to be a suitable tool for quality monitoring during fabrication and non-destructive evaluation of the LPBF process. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Graphical abstract

14 pages, 7488 KiB

Open AccessArticle

Direct Energy Deposition of TiAl for Hybrid Manufacturing and Repair of Turbine Blades

by Silja-Katharina Rittinghaus, Janett Schmelzer, Marcus Willi Rackel, Susanne Hemes, Andreas Vogelpoth, Ulrike Hecht and Andreas Weisheit

Materials 2020, 13(19), 4392; https://doi.org/10.3390/ma13194392 - 01 Oct 2020

Cited by 18 | Viewed by 3328

Abstract

While repair is mainly used to restore the original part geometry and properties, hybrid manufacturing aims to exploit the benefits of each respective manufacturing process regarding either processing itself or resulting part characteristics. Especially with the current implementation of additive manufacturing in the [...] Read more.

While repair is mainly used to restore the original part geometry and properties, hybrid manufacturing aims to exploit the benefits of each respective manufacturing process regarding either processing itself or resulting part characteristics. Especially with the current implementation of additive manufacturing in the production of TiAl, turbine blades for both hybrid manufacturing and repair new opportunities are enabled. One main issue is the compatibility of the two or more material types involved, which either differ regarding composition or microstructure or both. In this study, a TNM^TM-alloy (Ti-Nb-Mo) was manufactured by different processes (casting, forging, laser additive manufacturing) and identically heat-treated at 1290 °C. Chemical compositions, especially aluminum and oxygen contents, were measured, and the resulting microstructures were analyzed with Scanning Electron Microscopy (SEM) and High-energy X-ray diffraction (HEXRD). The properties were determined by hardness measurements and high-temperature compression tests. The comparison led to an overall assessment of the theoretical compatibility. Experiments to combine several processes were performed to evaluate the practical feasibility. Despite obvious differences in the final phase distribution caused by deviations in the chemical composition, the measured properties of the samples did not differ significantly. The feasibility of combining direct energy deposition (DED) with either casting or laser powder bed fusion (LPBF) was demonstrated by the successful build of the dense, crack-free hybrid material. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Figure 1

17 pages, 4022 KiB

Open AccessFeature PaperArticle

Laser Powder-Bed Fusion as an Alloy Development Tool: Parameter Selection for In-Situ Alloying Using Elemental Powders

by Leonardo Shoji Aota, Priyanshu Bajaj, Hugo Ricardo Zschommler Sandim and Eric Aimé Jägle

Materials 2020, 13(18), 3922; https://doi.org/10.3390/ma13183922 - 04 Sep 2020

Cited by 32 | Viewed by 4306

Abstract

The design of advanced alloys specifically tailored to additive manufacturing processes is a research field that is attracting ever-increasing attention. Laser powder-bed fusion (LPBF) commonly uses pre-alloyed, fine powders (diameter usually 15–45 µm) to produce fully dense metallic parts. The availability of such [...] Read more.

The design of advanced alloys specifically tailored to additive manufacturing processes is a research field that is attracting ever-increasing attention. Laser powder-bed fusion (LPBF) commonly uses pre-alloyed, fine powders (diameter usually 15–45 µm) to produce fully dense metallic parts. The availability of such fine, pre-alloyed powders reduces the iteration speed of alloy development for LPBF and renders it quite costly. Here, we overcome these drawbacks by performing in-situ alloying in LPBF starting with pure elemental powder mixtures avoiding the use of costly pre-alloyed powders. Pure iron, chromium, and nickel powder mixtures were used to perform in-situ alloying to manufacture 304 L stainless steel cube-shaped samples. Process parameters including scanning speed, laser power, beam diameter, and layer thickness were varied aiming at obtaining a chemically homogeneous alloy. The scientific questions focused on in this work are: which process parameters are required for producing such samples (in part already known in the state of the art), and why are these parameters conducive to homogeneity? Analytical modelling of the melt pool geometry and temperature field suggests that the residence time in the liquid state is the most important parameter controlling the chemical homogeneity of the parts. Results show that in-situ alloying can be successfully employed to enable faster and cost-efficient rapid alloy development. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Figure 1

12 pages, 7524 KiB

Open AccessArticle

Laser Powder Bed Fusion of Metal Coated Copper Powders

by Viktor Lindström, Oleksii Liashenko, Kai Zweiacker, Serhii Derevianko, Vladyslav Morozovych, Yurij Lyashenko and Christian Leinenbach

Materials 2020, 13(16), 3493; https://doi.org/10.3390/ma13163493 - 07 Aug 2020

Cited by 28 | Viewed by 4442

Abstract

Laser powder bed fusion (L-PBF) of copper alloys with high copper content is difficult due to the high infrared reflectivity and thermal conductivity of these alloys. In this study a simple and scalable method for coating copper powder with tin and nickel is [...] Read more.

Laser powder bed fusion (L-PBF) of copper alloys with high copper content is difficult due to the high infrared reflectivity and thermal conductivity of these alloys. In this study a simple and scalable method for coating copper powder with tin and nickel is presented, and suggested as an alloying strategy for such alloys. The coated powders were processed in a commercial L-PBF-machine at various scanning speeds. The samples made from coated powders show a lower amount of porosity compared to samples made from in-situ alloyed powders of similar composition. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Figure 1

24 pages, 8614 KiB

Open AccessArticle

Pandora’s Box–Influence of Contour Parameters on Roughness and Subsurface Residual Stresses in Laser Powder Bed Fusion of Ti-6Al-4V

by Katia Artzt, Tatiana Mishurova, Peter-Philipp Bauer, Joachim Gussone, Pere Barriobero-Vila, Sergei Evsevleev, Giovanni Bruno, Guillermo Requena and Jan Haubrich

Materials 2020, 13(15), 3348; https://doi.org/10.3390/ma13153348 - 28 Jul 2020

Cited by 21 | Viewed by 3215

Abstract

The contour scan strategies in laser powder bed fusion (LPBF) of Ti-6Al-4V were studied at the coupon level. These scan strategies determined the surface qualities and subsurface residual stresses. The correlations to these properties were identified for an optimization of the LPBF processing. [...] Read more.

The contour scan strategies in laser powder bed fusion (LPBF) of Ti-6Al-4V were studied at the coupon level. These scan strategies determined the surface qualities and subsurface residual stresses. The correlations to these properties were identified for an optimization of the LPBF processing. The surface roughness and the residual stresses in build direction were linked: combining high laser power and high scan velocities with at least two contour lines substantially reduced the surface roughness, expressed by the arithmetic mean height, from values as high as 30 µm to 13 µm, while the residual stresses rose from ~340 to about 800 MPa. At this stress level, manufactured rocket fuel injector components evidenced macroscopic cracking. A scan strategy completing the contour region at 100 W and 1050 mm/s is recommended as a compromise between residual stresses (625 MPa) and surface quality (14.2 µm). The LPBF builds were monitored with an in-line twin-photodiode-based melt pool monitoring (MPM) system, which revealed a correlation between the intensity quotient I₂/I₁, the surface roughness, and the residual stresses. Thus, this MPM system can provide a predictive estimate of the surface quality of the samples and resulting residual stresses in the material generated during LPBF. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Graphical abstract

14 pages, 2717 KiB

Open AccessArticle

In Situ and Ex Situ Characterization of the Microstructure Formation in Ni-Cr-Si Alloys during Rapid Solidification—Toward Alloy Design for Laser Additive Manufacturing

by Xiaoshuang Li, Kai Zweiacker, Daniel Grolimund, Dario Ferreira Sanchez, Adriaan B. Spierings, Christian Leinenbach and Konrad Wegener

Materials 2020, 13(9), 2192; https://doi.org/10.3390/ma13092192 - 10 May 2020

Cited by 3 | Viewed by 3135

Abstract

Laser beam-based deposition methods such as laser cladding or additive manufacturing of metals promises improved properties, performance, and reliability of the materials and therefore rely heavily on understanding the relationship between chemical composition, rapid solidification processing conditions, and resulting microstructural features. In this [...] Read more.

Laser beam-based deposition methods such as laser cladding or additive manufacturing of metals promises improved properties, performance, and reliability of the materials and therefore rely heavily on understanding the relationship between chemical composition, rapid solidification processing conditions, and resulting microstructural features. In this work, the phase formation of four Ni-Cr-Si alloys was studied as a function of cooling rate and chemical composition using a liquid droplet rapid solidification technique. Post mortem x-ray diffraction, scanning electron microscopy, and in situ synchrotron microbeam X-ray diffraction shows the present and evolution of the rapidly solidified microstructures. Furthermore, the obtained results were compared to standard laser deposition tests. In situ microbeam diffraction revealed that due to rapid cooling and an increasing amount of Cr and Si, metastable high-temperature silicides remain in the final microstructure. Due to more sluggish interface kinetics of intermetallic compounds than that of disorder solid solution, an anomalous eutectic structure becomes dominant over the regular lamellar microstructure at high cooling rates. The rapid solidification experiments produced a microstructure similar to the one generated in laser coating thus confirming that this rapid solidification test allows a rapid pre-screening of alloys suitable for laser beam-based processing techniques. Full article

(This article belongs to the Special Issue Challenges in Additive Manufacturing: From Coupon Studies to Components)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Challenges in Additive Manufacturing: From Coupon Studies to Components

Share This Special Issue

Special Issue Editor

Special Issue Information

Keywords

Published Papers (9 papers)

Research

Further Information

Guidelines

MDPI Initiatives

Follow MDPI