Research

Jump to: Review

1983 KiB

Open AccessArticle

Wireless Low-Power Integrated Basal-Body-Temperature Detection Systems Using Teeth Antennas in the MedRadio Band

by Chin-Lung Yang and Gou-Tsun Zheng

Sensors 2015, 15(11), 29467-29477; https://doi.org/10.3390/s151129467 - 20 Nov 2015

Cited by 8 | Viewed by 6113

This study proposes using wireless low power thermal sensors for basal-body-temperature detection using frequency modulated telemetry devices. A long-term monitoring sensor requires low-power circuits including a sampling circuit and oscillator. Moreover, temperature compensated technologies are necessary because the modulated frequency might have additional [...] Read more.

This study proposes using wireless low power thermal sensors for basal-body-temperature detection using frequency modulated telemetry devices. A long-term monitoring sensor requires low-power circuits including a sampling circuit and oscillator. Moreover, temperature compensated technologies are necessary because the modulated frequency might have additional frequency deviations caused by the varying temperature. The temperature compensated oscillator is composed of a ring oscillator and a controlled-steering current source with temperature compensation, so the output frequency of the oscillator does not drift with temperature variations. The chip is fabricated in a standard Taiwan Semiconductor Manufacturing Company (TSMC) 0.18-μm complementary metal oxide semiconductor (CMOS) process, and the chip area is 0.9 mm². The power consumption of the sampling amplifier is 128 µW. The power consumption of the voltage controlled oscillator (VCO) core is less than 40 µW, and the output is −3.04 dBm with a buffer stage. The output voltage of the bandgap reference circuit is 1 V. For temperature measurements, the maximum error is 0.18 °C with a standard deviation of ±0.061 °C, which is superior to the required specification of 0.1 °C. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Figure 1

2266 KiB

Open AccessArticle

Concept Design for a 1-Lead Wearable/Implantable ECG Front-End: Power Management

by Libin George, Gaetano Dario Gargiulo, Torsten Lehmann and Tara Julia Hamilton

Sensors 2015, 15(11), 29297-29315; https://doi.org/10.3390/s151129297 - 19 Nov 2015

Cited by 5 | Viewed by 5919

Abstract

Power supply quality and stability are critical for wearable and implantable biomedical applications. For this reason we have designed a reconfigurable switched-capacitor DC-DC converter that, aside from having an extremely small footprint (with an active on-chip area of only 0.04 mm²), [...] Read more.

Power supply quality and stability are critical for wearable and implantable biomedical applications. For this reason we have designed a reconfigurable switched-capacitor DC-DC converter that, aside from having an extremely small footprint (with an active on-chip area of only 0.04 mm²), uses a novel output voltage control method based upon a combination of adaptive gain and discrete frequency scaling control schemes. This novel DC-DC converter achieves a measured output voltage range of 1.0 to 2.2 V with power delivery up to 7.5 mW with 75% efficiency. In this paper, we present the use of this converter as a power supply for a concept design of a wearable (15 mm × 15 mm) 1-lead ECG front-end sensor device that simultaneously harvests power and communicates with external receivers when exposed to a suitable RF field. Due to voltage range limitations of the fabrication process of the current prototype chip, we focus our analysis solely on the power supply of the ECG front-end whose design is also detailed in this paper. Measurement results show not just that the power supplied is regulated, clean and does not infringe upon the ECG bandwidth, but that there is negligible difference between signals acquired using standard linear power-supplies and when the power is regulated by our power management chip. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Figure 1

892 KiB

Open AccessArticle

Wireless Power Transfer for Autonomous Wearable Neurotransmitter Sensors

by Cuong M. Nguyen, Pavan Kumar Kota, Minh Q. Nguyen, Souvik Dubey, Smitha Rao, Jeffrey Mays and J.-C. Chiao

Sensors 2015, 15(9), 24553-24572; https://doi.org/10.3390/s150924553 - 23 Sep 2015

Cited by 19 | Viewed by 7700

Abstract

In this paper, we report a power management system for autonomous and real-time monitoring of the neurotransmitter L-glutamate (L-Glu). A low-power, low-noise, and high-gain recording module was designed to acquire signal from an implantable flexible L-Glu sensor fabricated by micro-electro-mechanical system (MEMS)-based processes. [...] Read more.

In this paper, we report a power management system for autonomous and real-time monitoring of the neurotransmitter L-glutamate (L-Glu). A low-power, low-noise, and high-gain recording module was designed to acquire signal from an implantable flexible L-Glu sensor fabricated by micro-electro-mechanical system (MEMS)-based processes. The wearable recording module was wirelessly powered through inductive coupling transmitter antennas. Lateral and angular misalignments of the receiver antennas were resolved by using a multi-transmitter antenna configuration. The effective coverage, over which the recording module functioned properly, was improved with the use of in-phase transmitter antennas. Experimental results showed that the recording system was capable of operating continuously at distances of 4 cm, 7 cm and 10 cm. The wireless power management system reduced the weight of the recording module, eliminated human intervention and enabled animal experimentation for extended durations. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Graphical abstract

623 KiB

Open AccessArticle

Temperature and Humidity Sensor Powered by an Individual Microbial Fuel Cell in a Power Management System

by Qi Zheng, Lei Xiong, Bing Mo, Weihong Lu, Suki Kim and Zhenyu Wang

Sensors 2015, 15(9), 23126-23144; https://doi.org/10.3390/s150923126 - 11 Sep 2015

Cited by 24 | Viewed by 9243

Abstract

Microbial fuel cells (MFCs) are of increasing interest as bioelectrochemical systems for decomposing organic materials and converting chemical energy into electricity. The main challenge for this technology is that the low power and voltage of the devices restricts the use of MFCs in [...] Read more.

Microbial fuel cells (MFCs) are of increasing interest as bioelectrochemical systems for decomposing organic materials and converting chemical energy into electricity. The main challenge for this technology is that the low power and voltage of the devices restricts the use of MFCs in practical applications. In this paper, a power management system (PMS) is developed to store the energy and export an increased voltage. The designed PMS successfully increases the low voltage generated by an individual MFC to a high potential of 5 V, capable of driving a wireless temperature and humidity sensor based on nRF24L01 data transmission modules. With the PMS, MFCs can intermittently power the sensor for data transmission to a remote receiver. It is concluded that even an individual MFC can supply the energy required to power the sensor and telemetry system with the designed PMS. The presented PMS can be widely used for unmanned environmental monitoring such as wild rivers, lakes, and adjacent water areas, and offers promise for further advances in MFC technology. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Figure 1

1462 KiB

Open AccessArticle

Towards Low Energy Atrial Defibrillation

by Philip Walsh, Vivek Kodoth, David McEneaney, Paola Rodrigues, Jose Velasquez, Niall Waterman and Omar Escalona

Sensors 2015, 15(9), 22378-22400; https://doi.org/10.3390/s150922378 - 03 Sep 2015

Cited by 5 | Viewed by 6325

Abstract

A wireless powered implantable atrial defibrillator consisting of a battery driven hand-held radio frequency (RF) power transmitter (ex vivo) and a passive (battery free) implantable power receiver (in vivo) that enables measurement of the intracardiac impedance (ICI) during internal [...] Read more.

A wireless powered implantable atrial defibrillator consisting of a battery driven hand-held radio frequency (RF) power transmitter (ex vivo) and a passive (battery free) implantable power receiver (in vivo) that enables measurement of the intracardiac impedance (ICI) during internal atrial defibrillation is reported. The architecture is designed to operate in two modes: Cardiac sense mode (power-up, measure the impedance of the cardiac substrate and communicate data to the ex vivo power transmitter) and cardiac shock mode (delivery of a synchronised very low tilt rectilinear electrical shock waveform). An initial prototype was implemented and tested. In low-power (sense) mode, >5 W was delivered across a 2.5 cm air-skin gap to facilitate measurement of the impedance of the cardiac substrate. In high-power (shock) mode, >180 W (delivered as a 12 ms monophasic very-low-tilt-rectilinear (M-VLTR) or as a 12 ms biphasic very-low-tilt-rectilinear (B-VLTR) chronosymmetric (6ms/6ms) amplitude asymmetric (negative phase at 50% magnitude) shock was reliably and repeatedly delivered across the same interface; with >47% DC-to-DC (direct current to direct current) power transfer efficiency at a switching frequency of 185 kHz achieved. In an initial trial of the RF architecture developed, 30 patients with AF were randomised to therapy with an RF generated M-VLTR or B-VLTR shock using a step-up voltage protocol (50–300 V). Mean energy for successful cardioversion was 8.51 J ± 3.16 J. Subsequent analysis revealed that all patients who cardioverted exhibited a significant decrease in ICI between the first and third shocks (5.00 Ω (SD(σ) = 1.62 Ω), p < 0.01) while spectral analysis across frequency also revealed a significant variation in the impedance-amplitude-spectrum-area (IAMSA) within the same patient group (|∆(IAMSA_S1-IAMSA_S3)[1 Hz − 20 kHz] = 20.82 Ω-Hz (SD(σ) = 10.77 Ω-Hz), p < 0.01); both trends being absent in all patients that failed to cardiovert. Efficient transcutaneous power transfer and sensing of ICI during cardioversion are evidenced as key to the advancement of low-energy atrial defibrillation. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Figure 1

858 KiB

Open AccessArticle

A Low-Power and Portable Biomedical Device for Respiratory Monitoring with a Stable Power Source

by Jiachen Yang, Bobo Chen, Jianxiong Zhou and Zhihan Lv

Sensors 2015, 15(8), 19618-19632; https://doi.org/10.3390/s150819618 - 11 Aug 2015

Cited by 105 | Viewed by 8583

Abstract

Continuous respiratory monitoring is an important tool for clinical monitoring. Associated with the development of biomedical technology, it has become more and more important, especially in the measuring of gas flow and CO2 concentration, which can reflect the status of the patient. In [...] Read more.

Continuous respiratory monitoring is an important tool for clinical monitoring. Associated with the development of biomedical technology, it has become more and more important, especially in the measuring of gas flow and CO2 concentration, which can reflect the status of the patient. In this paper, a new type of biomedical device is presented, which uses low-power sensors with a piezoresistive silicon differential pressure sensor to measure gas flow and with a pyroelectric sensor to measure CO2 concentration simultaneously. For the portability of the biomedical device, the sensors and low-power measurement circuits are integrated together, and the airway tube also needs to be miniaturized. Circuits are designed to ensure the stability of the power source and to filter out the existing noise. Modulation technology is used to eliminate the fluctuations at the trough of the waveform of the CO2 concentration signal. Statistical analysis with the coefficient of variation was performed to find out the optimal driving voltage of the pressure transducer. Through targeted experiments, the biomedical device showed a high accuracy, with a measuring precision of 0.23 mmHg, and it worked continuously and stably, thus realizing the real-time monitoring of the status of patients. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Figure 1

1423 KiB

Open AccessArticle

A High Performance Delta-Sigma Modulator for Neurosensing

by Jian Xu, Menglian Zhao, Xiaobo Wu, Md. Kafiul Islam and Zhi Yang

Sensors 2015, 15(8), 19466-19486; https://doi.org/10.3390/s150819466 - 07 Aug 2015

Cited by 5 | Viewed by 8941

Abstract

Recorded neural data are frequently corrupted by large amplitude artifacts that are triggered by a variety of sources, such as subject movements, organ motions, electromagnetic interferences and discharges at the electrode surface. To prevent the system from saturating and the electronics from malfunctioning [...] Read more.

Recorded neural data are frequently corrupted by large amplitude artifacts that are triggered by a variety of sources, such as subject movements, organ motions, electromagnetic interferences and discharges at the electrode surface. To prevent the system from saturating and the electronics from malfunctioning due to these large artifacts, a wide dynamic range for data acquisition is demanded, which is quite challenging to achieve and would require excessive circuit area and power for implementation. In this paper, we present a high performance Delta-Sigma modulator along with several design techniques and enabling blocks to reduce circuit area and power. The modulator was fabricated in a 0.18-µm CMOS process. Powered by a 1.0-V supply, the chip can achieve an 85-dB peak signal-to-noise-and-distortion ratio (SNDR) and an 87-dB dynamic range when integrated over a 10-kHz bandwidth. The total power consumption of the modulator is 13 µW, which corresponds to a figure-of-merit (FOM) of 45 fJ/conversion step. These competitive circuit specifications make this design a good candidate for building high precision neurosensors. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Figure 1

Review

Jump to: Research

1900 KiB

Open AccessReview

Power Approaches for Implantable Medical Devices

by Achraf Ben Amar, Ammar B. Kouki and Hung Cao

Sensors 2015, 15(11), 28889-28914; https://doi.org/10.3390/s151128889 - 13 Nov 2015

Cited by 308 | Viewed by 18175

Abstract

Implantable medical devices have been implemented to provide treatment and to assess in vivo physiological information in humans as well as animal models for medical diagnosis and prognosis, therapeutic applications and biological science studies. The advances of micro/nanotechnology dovetailed with novel biomaterials have [...] Read more.

Implantable medical devices have been implemented to provide treatment and to assess in vivo physiological information in humans as well as animal models for medical diagnosis and prognosis, therapeutic applications and biological science studies. The advances of micro/nanotechnology dovetailed with novel biomaterials have further enhanced biocompatibility, sensitivity, longevity and reliability in newly-emerged low-cost and compact devices. Close-loop systems with both sensing and treatment functions have also been developed to provide point-of-care and personalized medicine. Nevertheless, one of the remaining challenges is whether power can be supplied sufficiently and continuously for the operation of the entire system. This issue is becoming more and more critical to the increasing need of power for wireless communication in implanted devices towards the future healthcare infrastructure, namely mobile health (m-Health). In this review paper, methodologies to transfer and harvest energy in implantable medical devices are introduced and discussed to highlight the uses and significances of various potential power sources. Full article

(This article belongs to the Special Issue Power Schemes for Biosensors and Biomedical Devices)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Power Schemes for Biosensors and Biomedical Devices

Share This Special Issue

Special Issue Editors

Special Issue Information

Keywords

Published Papers (8 papers)

Research

Review

Further Information

Guidelines

MDPI Initiatives

Follow MDPI