Research

Jump to: Review

15 pages, 1690 KiB

Open AccessArticle

A Microwave Differential Dielectric Sensor Based on Mode Splitting of Coupled Resonators

by Ali M. Almuhlafi, Mohammed S. Alshaykh, Mansour Alajmi, Bassam Alshammari and Omar M. Ramahi

Sensors 2024, 24(3), 1020; https://doi.org/10.3390/s24031020 - 05 Feb 2024

Viewed by 898

This study explores the viability of using the avoided mode crossing phenomenon in the microwave regime to design microwave differential sensors. While the design concept can be applied to any type of planar electrically small resonators, here, it is implemented on split-ring resonators [...] Read more.

This study explores the viability of using the avoided mode crossing phenomenon in the microwave regime to design microwave differential sensors. While the design concept can be applied to any type of planar electrically small resonators, here, it is implemented on split-ring resonators (SRRs). We use two coupled synchronous SRRs loaded onto a two-port microstrip line system to demonstrate the avoided mode crossing by varying the distance between the split of the resonators to control the coupling strength. As the coupling becomes stronger, the split in the resonance frequencies of the system increases. Alternatively, by controlling the strength of the coupling by materials under test (MUTs), we utilize the system as a microwave differential sensor. First, the avoided mode crossing is theoretically investigated using the classical microwave coupled resonator techniques. Then, the system is designed and simulated using a 3D full-wave numerical simulation. To validate the concept, a two-port microstrip line, which is magnetically coupled to two synchronous SRRs, is utilized as a sensor, where the inter-resonator coupling is chosen to be electric coupling controlled by the dielectric constant of MUTs. For the experimental validation, the sensor was fabricated using printed circuit board technology. Two solid slabs with dielectric constants of 2.33 and 9.2 were employed to demonstrate the potential of the system as a novel differential microwave sensor. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

23 pages, 11757 KiB

Open AccessArticle

Interconnect for Dense Electronically Scanned Antenna Array Using High-Speed Vertical Connector

by Nooshin Valizade Shahmirzadi, Natalia K. Nikolova and Chih-Hung Chen

Sensors 2023, 23(20), 8596; https://doi.org/10.3390/s23208596 - 20 Oct 2023

Viewed by 854

Abstract

We present the design and the performance evaluation of a new interconnect for large-scale densely packed electronically scanned antenna arrays that utilize a high-speed digital board-to-board vertical connector. The application targets microwave tissue, imaging in the frequency range from 3 GHz to 8 [...] Read more.

We present the design and the performance evaluation of a new interconnect for large-scale densely packed electronically scanned antenna arrays that utilize a high-speed digital board-to-board vertical connector. The application targets microwave tissue, imaging in the frequency range from 3 GHz to 8 GHz. The tissue-imaging arrays consist of hundreds of active antenna elements, which require low-reflection, low-loss, and low-crosstalk connections to their respective receiving and transmitting circuits. The small antenna size and the high array density preclude the use of coaxial connectors, which are also expensive and mechanically unreliable. Modern board-to-board high-speed connectors promise bandwidths as high as 12 GHz, along with high pin density, mechanical robustness, and low cost. However, their compatibility with the various transmission lines leading to/from the miniature printed antenna elements and microwave circuitry is not well studied. Here, we focus on the design of the transitions from coplanar waveguide transmission lines to/from a high-speed vertical connector. The performance of the interconnect is examined through electromagnetic simulations and measurements. Comparison is carried out with the expensive sub-miniature push-on sub-micro coaxial connectors commonly used in miniature radio-frequency electronics. The results demonstrate that high-speed vertical connectors can provide comparable performance in the UWB frequency range. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

18 pages, 12088 KiB

Open AccessArticle

Four-Port 38 GHz MIMO Antenna with High Gain and Isolation for 5G Wireless Networks

by Ahmed A. Ibrahim, Wael A. E. Ali, Moath Alathbah and Ayman R. Sabek

Sensors 2023, 23(7), 3557; https://doi.org/10.3390/s23073557 - 28 Mar 2023

Cited by 11 | Viewed by 1860

Abstract

In this paper, a 38 GHz 4-port multiple-input multiple-output (MIMO) antenna with considerable isolation and gain enhancement for 5G applications is introduced. The suggested antenna element is a monopole antenna composed of a circular patch with a rectangular slot etched from it and [...] Read more.

In this paper, a 38 GHz 4-port multiple-input multiple-output (MIMO) antenna with considerable isolation and gain enhancement for 5G applications is introduced. The suggested antenna element is a monopole antenna composed of a circular patch with a rectangular slot etched from it and a partial ground plane is used to extend the desired frequency to operate from 36.6 GHz to 39.5 GHz with a center frequency of 38 GHz. The high isolation is achieved by arranging the four elements orthogonally and adding four stubs to reduce mutual coupling between elements at the desired frequency bands. The gain improvement is also introduced by placing a frequency selective structure (FSS) which is designed at the same frequency bands of the antenna under the suggested MIMO antenna to act as a reflector. The proposed four-element MIMO with the FSS prototype is built and tested in order to confirm the simulated results. The suggested antenna operated from 37.2 GHz to 39.2 GHz with an isolation of less than 25 dB across the obtained frequency range. The peak gain of the antenna is enhanced from 5.5 dBi to around 10 dBi by utilizing the FSS structure; furthermore, the back radiation is enhanced. The MIMO performance is validated by extracting its parameters and comparing with the simulated results. The results extracted from the simulation and the measurement show satisfactory matching along with the target band, indicating that the proposed structure could be used for 5G communications. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

19 pages, 4400 KiB

Open AccessArticle

Optimizing Cardiac Wireless Implant Communication: A Feasibility Study on Selecting the Frequency and Matching Medium

by Bilal Amin, Muhammad Riaz ur Rehman, Muhammad Farooq, Adnan Elahi, Kevin Donaghey, William Wijns, Atif Shahzad and Patricia Vazquez

Sensors 2023, 23(7), 3411; https://doi.org/10.3390/s23073411 - 24 Mar 2023

Viewed by 1741

Abstract

Cardiac wireless implantable medical devices (CWIMD) have brought a paradigm shift in monitoring and treating various cardiac conditions, including heart failure, arrhythmias, and hypertension. One of the key elements in CWIMD is the implant antenna which uses radio frequency (RF) technology to wirelessly [...] Read more.

Cardiac wireless implantable medical devices (CWIMD) have brought a paradigm shift in monitoring and treating various cardiac conditions, including heart failure, arrhythmias, and hypertension. One of the key elements in CWIMD is the implant antenna which uses radio frequency (RF) technology to wirelessly communicate and transmit data to external devices. However, wireless communication with a deeply implanted antenna using RF can be challenging due to the significant loss of electromagnetic (EM) signal at the air–skin interface, and second, due to the propagation and reflection of EM waves from different tissue boundaries. The air–skin interface loss of the EM wave is pronounced due to the absence of a matching medium. This paper investigates the EM propagation losses in the human body and presents a choice of optimal frequency for the design of the cardiac implant antenna and the dielectric properties of the matching medium. First, the dielectric properties of all tissues present in the human thorax including skin, fat, muscle, cartilage, and heart are analyzed as a function of frequency to study the EM wave absorption at different frequencies. Second, the penetration of EM waves inside the biological tissues is analyzed as a function of frequency. Third, a transmission line (TL) formalism approach is adopted to examine the optimal frequency band for designing a cardiac implant antenna and the matching medium for the air–skin interface. Finally, experimental validation is performed at two ISM frequencies, 433 MHz and 915 MHz, selected from the optimal frequency band (0.4–1.5 GHz) suggested by our analytical investigation. For experimental validation, two off-the-shelf flexible dipole antennas operating at selected ISM frequencies were used. The numerical and experimental findings suggested that for the specific application of a cardiac implant with a penetration depth of 7–17 cm, the most effective frequency range for operation is within 0.4–1.5 GHz. The findings based on the dielectric properties of thorax tissues, the penetration depth of EM waves, and the optimal frequency band have provided valuable information on developing and optimizing CWIMDs for cardiac care applications. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

12 pages, 3833 KiB

Open AccessArticle

Microwave NDT of Smart Composite Structures with Embedded Antennas

by Mohammed Saif ur Rahman, Omar Samir Hassan, Ademola Akeem Mustapha, Mohamed A. Abou-Khousa and Wesley James Cantwell

Sensors 2023, 23(6), 3200; https://doi.org/10.3390/s23063200 - 17 Mar 2023

Viewed by 2011

Abstract

The integration of antennas in composite structures is gaining popularity with advances in wireless communications and the ever-increasing demands for efficient smart structures. Efforts are ongoing to ensure that antenna-embedded composite structures are robust and resilient to inevitable impacts, loading and other external [...] Read more.

The integration of antennas in composite structures is gaining popularity with advances in wireless communications and the ever-increasing demands for efficient smart structures. Efforts are ongoing to ensure that antenna-embedded composite structures are robust and resilient to inevitable impacts, loading and other external factors that threaten the structural integrity of these structures. Undoubtedly, the in situ inspection of such structures to identify anomalies and predict failures is required. In this paper, the microwave non-destructive testing (NDT) of antenna-embedded composite structures is introduced for the first time. The objective is accomplished using a planar resonator probe operating in the UHF frequency range (~525 MHz). High-resolution images of a C-band patch antenna fabricated on an aramid paper-based honeycomb substrate and covered with a glass fiber reinforced polymer (GFRP) sheet are presented. The imaging prowess of microwave NDT and its distinct advantages in inspecting such structures are highlighted. The qualitative as well as the quantitative evaluation of the images produced by the planar resonator probe and a conventional K-band rectangular aperture probe are included. Overall, the potential utility of microwave NDT for the inspection of smart structures is demonstrated. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

9 pages, 3009 KiB

Open AccessCommunication

In-Line Wood Defect Detection Using Simple Scalar Network Analyzer

by Mohamed Radwan, Noah Becker, David V. Thiel and Hugo G. Espinosa

Sensors 2022, 22(23), 9495; https://doi.org/10.3390/s22239495 - 05 Dec 2022

Cited by 2 | Viewed by 1436

Abstract

Timber is widely used in new structures. The leading causes of structural failure are sited at bolt connections, cavities, and knots. This paper introduces a simple method to detect bolts in wood using a UHF Scalar Network Analyzer (SNA). The electronics placed inside [...] Read more.

Timber is widely used in new structures. The leading causes of structural failure are sited at bolt connections, cavities, and knots. This paper introduces a simple method to detect bolts in wood using a UHF Scalar Network Analyzer (SNA). The electronics placed inside an aluminum box with a slot aperture transmit a microwave signal through the slot, and the near-field signal determines the reflection coefficient (S₁₁). Major changes from baseline are an accurate method to detect cavities and bolts inside the wood. Experiments were conducted on pinewood beams with cross-section dimensions of (70 mm × 70 mm). The scalar network analyzer circuit can detect bolts and cavities within a 30 mm range from the wood surface. The technique can be used for timber beam preparation in an automated sawmill at speed. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

18 pages, 4618 KiB

Open AccessArticle

Slotted Monopole Patch Antenna for Microwave-Based Head Imaging Applications

by Abdulrahman Alqahtani, Mohammad Tariqul Islam, Md Siam Talukder, Md Samsuzzaman, Mohsen Bakouri, Sofiene Mansouri, Thamer Almoneef, Socrates Dokos and Yousef Alharbi

Sensors 2022, 22(19), 7235; https://doi.org/10.3390/s22197235 - 23 Sep 2022

Cited by 3 | Viewed by 2254

Abstract

A modified monopole patch antenna for microwave-based hemorrhagic or ischemic stroke recognition is presented in this article. The designed antenna is fabricated on a cost-effective FR-4 lossy material with a 0.02 loss tangent and 4.4 dielectric constant. Its overall dimensions are 0.32 λ [...] Read more.

A modified monopole patch antenna for microwave-based hemorrhagic or ischemic stroke recognition is presented in this article. The designed antenna is fabricated on a cost-effective FR-4 lossy material with a 0.02 loss tangent and 4.4 dielectric constant. Its overall dimensions are 0.32 λ × 0.28 λ × 0.007 λ, where λ is the lower bandwidth 1.3 GHz frequency wavelength. An inset feeding approach is utilized to feed the antenna to reduce the input impedance (z = voltage/current). A total bandwidth (below −10 dB) of 2.4 GHz (1.3–3.7 GHz) is achieved with an effective peak gain of over 6 dBi and an efficiency of over 90%. A time-domain analysis confirms that the antenna produces minimal signal distortion. Simulated and experimental findings share a lot of similarities. Brain tissue is penetrated by the antenna to a satisfactory degree, while still exhibiting a safe specific absorption rate (SAR). The maximum SAR value measured for the head model is constrained to be equal to or below 0.1409 W/kg over the entire usable frequency band. Evaluation of theoretical and experimental evidence indicates the intended antenna is appropriate for Microwave Imaging (MWI) applications. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

Review

Jump to: Research

29 pages, 911 KiB

Open AccessReview

Review and Analysis of Tumour Detection and Image Quality Analysis in Experimental Breast Microwave Sensing

by Tyson Reimer and Stephen Pistorius

Sensors 2023, 23(11), 5123; https://doi.org/10.3390/s23115123 - 27 May 2023

Cited by 3 | Viewed by 1528

Abstract

This review evaluates the methods used for image quality analysis and tumour detection in experimental breast microwave sensing (BMS), a developing technology being investigated for breast cancer detection. This article examines the methods used for image quality analysis and the estimated diagnostic performance [...] Read more.

This review evaluates the methods used for image quality analysis and tumour detection in experimental breast microwave sensing (BMS), a developing technology being investigated for breast cancer detection. This article examines the methods used for image quality analysis and the estimated diagnostic performance of BMS for image-based and machine-learning tumour detection approaches. The majority of image analysis performed in BMS has been qualitative and existing quantitative image quality metrics aim to describe image contrast—other aspects of image quality have not been addressed. Image-based diagnostic sensitivities between 63 and 100% have been achieved in eleven trials, but only four articles have estimated the specificity of BMS. The estimates range from 20 to 65%, and do not demonstrate the clinical utility of the modality. Despite over two decades of research in BMS, significant challenges remain that limit the development of this modality as a clinical tool. The BMS community should utilize consistent image quality metric definitions and include image resolution, noise, and artifacts in their analyses. Future work should include more robust metrics, estimates of the diagnostic specificity of the modality, and machine-learning applications should be used with more diverse datasets and with robust methodologies to further enhance BMS as a viable clinical technique. Full article

(This article belongs to the Special Issue Toward Advanced Microwave Sensors)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Toward Advanced Microwave Sensors

Share This Special Issue

Special Issue Editors

Special Issue Information

Keywords

Published Papers (8 papers)

Research

Review

Further Information

Guidelines

MDPI Initiatives

Follow MDPI