State of Art in Hip, Knee and Shoulder Replacement (Volume 2)

A special issue of Prosthesis (ISSN 2673-1592).

Deadline for manuscript submissions: 30 November 2024 | Viewed by 572

Special Issue Editors


E-Mail Website
Guest Editor
Department of Basic Medical Sciences, Neuroscience and Organs of Sense, School of Medicine, Uo Orthopaedics and Traumatology, Aou Policlinico, Università Di Bari "Aldo Moro", 70124 Bari, Italy
Interests: primary and revision hip and knee replacement; treatment of femoral fractures
Special Issues, Collections and Topics in MDPI journals

E-Mail Website
Guest Editor
AO Ordine Mauriziano Hospital, Department of Orthopaedics and Traumatology, University of Torino, Largo Turati 62, 10128 Torino, Italy
Interests: hip and knee arthroplasty; knee surgery
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

The great success of the first volume of this Special Issue, “State of Art in Hip and Knee Replacement”, was of huge satisfaction and a great signal for the editors of Prosthesis, encouraging for the second volume.

A joint replacement is considered routine and in some institutions is even performed as an outpatient surgery, but this can be confused with an easy procedure with no implications. This is a great mistake that has to be limited, and knowledge is the only way to do so.

Joint replacement surgery must be considered by young and even experienced surgeons due to the impact on patients’ activity and quality of life. In addition, patient populations are growing in different directions; older people for pain relief and young patients for increasing daily activity.

This aspect represents a great challenge and makes it even more difficult to standardize the treatment due to the high variability in indication and expectations.

In this volume of “State of the Art in Hip, Knee and Shoulder Replacement” we will focus on replacement surgeries of the hip and knee—as in the previous one—but we will also include the shoulder, to address all the bigger joints and give a broad perspective on more up-to-date surgical techniques, indications, and results.

We are living in a new golden era of orthopedic surgery thanks to the great boost of technology (e.g., robotics, artificial intelligence) that is giving new stamina to research and clinical outcomes; particular attention will be given to this aspect, which in our vision is of paramount importance for the future.

It is mandatory for surgeons to have high levels of skill and knowledge to perform a time-saving, tissue-sparing, and highly effective procedure that can give patients a better and faster recovery, reducing the risk of infection or complications.

This Special Issue would like to be a thorough investigation of the actual state of the art in hip, knee, and shoulder replacement, with the contributions of great surgeons, scientists, and clinicians that apply the best practices to their patients every day.

This is a new great opportunity to give a guide to joint replacement surgeons and the correct visibility to useful papers.

Prof. Dr. Giuseppe Solarino
Dr. Umberto Cottino
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Prosthesis is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 1600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • hip prostheses
  • knee prostheses
  • shoulder prostheses

Related Special Issue

Published Papers (1 paper)

Order results
Result details
Select all
Export citation of selected articles as:

Research

8 pages, 1242 KiB  
Article
Dual Mobility Hip Arthroplasty: Innovative Technological Advances
by Domenico Tigani, Ludovica Solito, Stefano Stallone, Corrado Maria Leonida, Tommaso Dieterich, Francesco Taverniti, Lorenzo Banci and Giuseppe Melucci
Prosthesis 2024, 6(2), 393-400; https://doi.org/10.3390/prosthesis6020029 - 17 Apr 2024
Viewed by 339
Abstract
The use of 3D-printed highly porous titanium acetabular cups in total hip arthroplasty (THA) is increasing. The porosity and mechanical properties of such highly porous titanium structures mimic those of natural cancellous bone, possibly allowing biological implant fixation to be improved. Recently, a [...] Read more.
The use of 3D-printed highly porous titanium acetabular cups in total hip arthroplasty (THA) is increasing. The porosity and mechanical properties of such highly porous titanium structures mimic those of natural cancellous bone, possibly allowing biological implant fixation to be improved. Recently, a 3D-printed highly porous Dual Mobility (DM) monobloc construct fully manufactured using Ti6Al4V alloy, with a titanium–niobium nitride (TiNbN) ceramic coating on the articular side to allow articulation against the mobile liner by improving the titanium vs. polyethylene tribological behavior, was introduced in THA. To the best of our knowledge, this is the first highly porous titanium monobloc DM implant on the market. The reasons for using a Ti alloy highly porous DM are multifarious: to prevent any possible adverse reactions due to the corrosion of Cobalt–Chromium–Molybdenum Alloy (CoCrMo) and Stainless Steel (SS) implants and to improve implant primary and secondary stability, particularly in cases of poor bone quality. Finally, with the introduction of an inner TiNbN ceramic coating surface, it was possible to overcome the poor tribological quality of titanium. Another interesting characteristic is this material’s higher implant radiolucency, which might facilitate the radiographic assessment of cup orientation, which can, in turn, facilitate the detection of any intraprosthetic dislocation (IPD) and the measurement of polyethylene wear, which is very important in the study of the durability of THA. Full article
(This article belongs to the Special Issue State of Art in Hip, Knee and Shoulder Replacement (Volume 2))
Show Figures

Figure 1

Back to TopTop