Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
4.4
2.9
Journals
Metals
Special Issues
Research on Mechanical Properties, Deformation, and Microstructures of Metallic Materials
share announcement

Research on Mechanical Properties, Deformation, and Microstructures of Metallic Materials

A special issue of Metals (ISSN 2075-4701). This special issue belongs to the section "Structural Integrity of Metals".

Deadline for manuscript submissions: 20 June 2024 | Viewed by 1666

Special Issue Editor

Prof. Dr. Qingsong Mei

E-Mail Website
Guest Editor
School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072, China
Interests: microstructure design of advanced metallic materials; metal matrix composites; strengthening mechanism; microstructure–property tailoring during manufacturing

Special Issue Information

Dear Colleagues,

There have been continuous advances in the design and manufacturing of microstructures, as well as the new understanding of the microstructure–property relations of metallic materials for structural applications in recent years. This Special Issue, entitled “Research on Mechanical Properties, Deformation, Microstructures of Metallic Materials”, will underline the most recent discoveries and progress in the microstructure and mechanical behaviors of various types of metallic materials. Topics include, but are not limited to, nanostructured and ultrafine-grained metals, metal–matrix composites, high-temperature alloys, high-entropy alloys, metallic biomaterials, heterogeneous nano/micro-structure design, 3D-printing, surface engineering, deformation manufacturing, strengthening and toughening mechanisms, high-strain-rate deformation, microstructure tailoring during advanced forming and manufacturing, heat treatment of metals, etc. We welcome the submission of original research articles, communications, and reviews on recent advances in the related areas of metallic materials.

All of these contributions will provide new insights into the microstructure and mechanical properties of metallic materials for advanced structural applications.

Prof. Dr. Qingsong Mei
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Metals is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • metals and alloys
  • mechanical properties
  • microstructure design
  • deformation
  • strengthening
  • toughening
  • advanced forming and manufacturing

Published Papers (2 papers)

Download All Papers
Order results
Result details
Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:

Research

12 pages, 6202 KiB  
Article
Hydride-Induced Responses in the Mechanical Behavior of Zircaloy-4 Sheets
by Hsiao-Ming Tung and Tai-Cheng Chen
Metals 2024, 14(2), 177; https://doi.org/10.3390/met14020177 - 01 Feb 2024
Viewed by 710
Abstract
This study aimed to investigate the impact of hydrogen content, up to 1217 ppm, on the mechanical properties of Zircaloy-4, with a particular focus on the formation and impact of hydrides. Tensile specimens were tested across a range of temperatures and hydrogen concentrations. [...] Read more.
This study aimed to investigate the impact of hydrogen content, up to 1217 ppm, on the mechanical properties of Zircaloy-4, with a particular focus on the formation and impact of hydrides. Tensile specimens were tested across a range of temperatures and hydrogen concentrations. The results revealed a pronounced ductile-to-brittle transition associated with hydride formation. When the hydrogen content in the specimens ranged between 700 and 850 ppm, a ductile-to-brittle transition was observed at temperatures of 25 °C, 50 °C, and 75 °C. At 25 °C, the ultimate tensile strength (UTS) of Zircaloy-4 linearly increased as the hydrogen concentration rose from 0 to 1217 ppm H. However, at higher temperatures, the behavior of UTS became more complex, especially in the hydrogen concentration ranges of 500–850 ppm H. Elongation (EL) in the hydrided specimens was affected by both temperature and hydrogen concentration. As hydrogen concentration increased, there was a noticeable decline in uniform EL, while non-uniform EL showed even more significant reductions. Scanning electron microscopy (SEM) analysis of the fracture surfaces revealed that quasi-cleavage features became evident when the hydrogen content reached 850 ppm H, across all tested temperatures. These findings not only provide a quantitative assessment of the safety implications of Zircaloy-4 in nuclear reactor applications but also highlight the importance of the hydrogen charging process and mechanical testing in understanding its mechanical behavior. Full article
(This article belongs to the Special Issue Research on Mechanical Properties, Deformation, and Microstructures of Metallic Materials)
►▼ Show Figures

Figure 1

15 pages, 6741 KiB  
Article
Determining Hot Deformation Behavior and Rheology Laws of Selected Austenitic Stainless Steels
by Josef Němec, Lenka Kunčická, Petr Opěla and Karel Dvořák
Metals 2023, 13(11), 1902; https://doi.org/10.3390/met13111902 - 17 Nov 2023
Viewed by 783
Abstract
Due to their versatile properties, austenitic stainless steels have a wide application potential, including in specific fields, such as the nuclear power industry. ChN35VT steel is a chromium–nickel–tungsten type of steel stabilized by titanium, and it is suitable for parts subjected to considerable [...] Read more.
Due to their versatile properties, austenitic stainless steels have a wide application potential, including in specific fields, such as the nuclear power industry. ChN35VT steel is a chromium–nickel–tungsten type of steel stabilized by titanium, and it is suitable for parts subjected to considerable mechanical stress at elevated temperatures. However, the available data on its deformation behavior at elevated/high temperatures is scarce. The core of the presented research was thus the experimental characterization of the deformation behavior of the ChN35VT steel under hot conditions via the determination of flow stress curves, and their correlation with microstructure development. The obtained data was further compared with data acquired for 08Ch18N10T steel, which is also known for its applicability in the nuclear power industry. The experimental results were subsequently used to determine the Hensel-Spittel rheology laws for both the steels. The ChN35VT steel exhibited notably higher flow stress values in comparison with the 08Ch18N10T steel. This difference was more significant the lower the temperature and the higher the strain rate. Considering the peak stress values, the lowest difference was ~8 MPa (1250 °C and 0.01 s−1), and the highest was ~150 MPa (850 °C and 10 s−1). These findings also corresponded to the microstructure developments—the higher the deformation temperature, the more negligible the observed differences as regards the grain size and morphology. Full article
(This article belongs to the Special Issue Research on Mechanical Properties, Deformation, and Microstructures of Metallic Materials)
►▼ Show Figures

Figure 1

Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:
 
Displaying articles 1-2
Back to TopTop