Energies

Research

15 pages, 2070 KiB

Open AccessArticle

The Influences of NP100 Surfactant and Pine-Oil Concentrations on Filtrate Volume and Filter-Cake Thickness of Microemulsion-Based Drilling Fluids (O/W)

by Agostinho C. B. Junior, Raphael R. Silva, Giovanna L. R. Leal, Tarsila M. Tertuliano, Rafael P. Alves, Alfredo I. C. Garnica and Fabiola D. S. Curbelo

Energies 2021, 14(16), 4965; https://doi.org/10.3390/en14164965 - 13 Aug 2021

Cited by 4 | Viewed by 2151

Abstract

In this work, nonionic surfactant NP100 and pine oil influences on the filtrate volume (F_V) and the filter-cake thickness (thkns) of microemulsified drilling fluids were studied. A ternary phase diagram was obtained to define the microemulsion region, where a 2^k [...] Read more.

In this work, nonionic surfactant NP100 and pine oil influences on the filtrate volume (F_V) and the filter-cake thickness (thkns) of microemulsified drilling fluids were studied. A ternary phase diagram was obtained to define the microemulsion region, where a 2^k factorial design was used with the addition of four center points and axial points. Twelve microemulsion points were defined and used later in the formulation of the investigated drilling fluids. The results showed that the increase in the surfactant and pine oil’s concentration increased F_V and thkns, withthe oil phase being the most influential component in the filtrate volume and the surfactant being the most influential in the filter-cake thickness. Statistically significant models were obtained. The optimal concentrations were determined for the lowest F_V and thkns; 45% of surfactant and 5% of pine oil for the filtrate volume (1.3 mL), and 45% of surfactant and 15% of pine oil for the filter-cake thickness (0.64 mm). Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Graphical abstract

19 pages, 4823 KiB

Open AccessArticle

Assessing the Relation between Mud Components and Rheology for Loss Circulation Prevention Using Polymeric Gels: A Machine Learning Approach

by Musaab I. Magzoub, Raj Kiran, Saeed Salehi, Ibnelwaleed A. Hussein and Mustafa S. Nasser

Energies 2021, 14(5), 1377; https://doi.org/10.3390/en14051377 - 3 Mar 2021

Cited by 7 | Viewed by 2163

Abstract

The traditional way to mitigate loss circulation in drilling operations is to use preventative and curative materials. However, it is difficult to quantify the amount of materials from every possible combination to produce customized rheological properties. In this study, machine learning (ML) is [...] Read more.

The traditional way to mitigate loss circulation in drilling operations is to use preventative and curative materials. However, it is difficult to quantify the amount of materials from every possible combination to produce customized rheological properties. In this study, machine learning (ML) is used to develop a framework to identify material composition for loss circulation applications based on the desired rheological characteristics. The relation between the rheological properties and the mud components for polyacrylamide/polyethyleneimine (PAM/PEI)-based mud is assessed experimentally. Four different ML algorithms were implemented to model the rheological data for various mud components at different concentrations and testing conditions. These four algorithms include (a) k-Nearest Neighbor, (b) Random Forest, (c) Gradient Boosting, and (d) AdaBoosting. The Gradient Boosting model showed the highest accuracy (91 and 74% for plastic and apparent viscosity, respectively), which can be further used for hydraulic calculations. Overall, the experimental study presented in this paper, together with the proposed ML-based framework, adds valuable information to the design of PAM/PEI-based mud. The ML models allowed a wide range of rheology assessments for various drilling fluid formulations with a mean accuracy of up to 91%. The case study has shown that with the appropriate combination of materials, reasonable rheological properties could be achieved to prevent loss circulation by managing the equivalent circulating density (ECD). Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

11 pages, 2299 KiB

Open AccessArticle

Hybrid Washer Fluid for Primary Cementing

by Marcin Kremieniewski

Energies 2021, 14(5), 1295; https://doi.org/10.3390/en14051295 - 26 Feb 2021

Cited by 4 | Viewed by 1640

Abstract

This article presents the results on the basis of which a new hybrid drilling washer fluid was designed. The use of fluid from such a drilling washer increases the mud-cake removal efficiency. Its operation is based on both chemical and mechanical removal of [...] Read more.

This article presents the results on the basis of which a new hybrid drilling washer fluid was designed. The use of fluid from such a drilling washer increases the mud-cake removal efficiency. Its operation is based on both chemical and mechanical removal of the mud cake. This article presents a group of agents and admixtures of various solid fractions, the appropriate selection of which enabled the design of a hybrid drilling washer fluid. The liquid has much better washing parameters than the drilling washers used so far. The tests were carried out in a drilling fluid flow simulator. A significant improvement in the scrubbing mud-cake removal efficiency resulted from the action of surfactants and fine-grained abrasive additives. Their proper concentration was also very important. The hybrid drilling washer fluid was designed on the basis of tests measuring the adhesion of the hardened cement slurry to the rock from which the previously produced mud was removed. In this way, the effectiveness of the washing liquids was determined. Upon analyzing the obtained results and correlating them with the reference samples, one can see a significant improvement in the efficiency of the removal of the drilling sediment by the hybrid drilling washer fluid. The hybrid drilling washer fluid is an innovative solution because it combines chemical and mechanical action in the removal of drilling fluid. Additionally, such a washing liquid has not been used so far. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

28 pages, 11248 KiB

Open AccessArticle

Experimental Study of Single Taylor Bubble Rising in Stagnant and Downward Flowing Non-Newtonian Fluids in Inclined Pipes

by Yaxin Liu, Eric R. Upchurch and Evren M. Ozbayoglu

Energies 2021, 14(3), 578; https://doi.org/10.3390/en14030578 - 23 Jan 2021

Cited by 40 | Viewed by 3466

Abstract

An experimental investigation of single Taylor bubbles rising in stagnant and downward flowing non-Newtonian fluids was carried out in an 80 ft long inclined pipe (4°, 15°, 30°, 45° from vertical) of 6 in. inner diameter. Water and four concentrations of bentonite–water mixtures [...] Read more.

An experimental investigation of single Taylor bubbles rising in stagnant and downward flowing non-Newtonian fluids was carried out in an 80 ft long inclined pipe (4°, 15°, 30°, 45° from vertical) of 6 in. inner diameter. Water and four concentrations of bentonite–water mixtures were applied as the liquid phase, with Reynolds numbers in the range 118 < Re < 105,227 in countercurrent flow conditions. The velocity and length of Taylor bubbles were determined by differential pressure measurements. The experimental results indicate that for all fluids tested, the bubble velocity increases as the inclination angle increases, and decreases as liquid viscosity increases. The length of Taylor bubbles decreases as the downward flow liquid velocity and viscosity increase. The bubble velocity was found to be independent of the bubble length. A new drift velocity correlation that incorporates inclination angle and apparent viscosity was developed, which is applicable for non-Newtonian fluids with the Eötvös numbers (

E_{0}

) ranging from 3212 to 3405 and apparent viscosity (

μ_{a p p}

) ranging from 0.001 Pa∙s to 129 Pa∙s. The proposed correlation exhibits good performance for predicting drift velocity from both the present study (mean absolute relative difference is 0.0702) and a database of previous investigator’s results (mean absolute relative difference is 0.09614). Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

21 pages, 4053 KiB

Open AccessArticle

The Effect of Salt on Stability of Aqueous Foams

by Oyindamola Obisesan, Ramadan Ahmed and Mahmood Amani

Energies 2021, 14(2), 279; https://doi.org/10.3390/en14020279 - 6 Jan 2021

Cited by 26 | Viewed by 3982

Abstract

The properties of foams are often affected by environmental variables such as salt contamination. The objective of this study is to investigate the impact of salt on the drainage behavior of aqueous foams. To accomplish this objective, drainage experiments were conducted on aqueous [...] Read more.

The properties of foams are often affected by environmental variables such as salt contamination. The objective of this study is to investigate the impact of salt on the drainage behavior of aqueous foams. To accomplish this objective, drainage experiments were conducted on aqueous foams. Test variables were foam quality (40–65%), and salt content (0% to 18%), and type. To investigate drainage, the foam was generated in a flow loop and trapped in a vertical test section. Then, the pressure profile in the foam column was measured using ten pressure sensors. Foam drainage is determined as a function of time using measured pressure profiles. The results show that the drainage of NaCl-containing foams decreased with foam quality, whereas the CaCl₂-containing foams did not exhibit a clear trend with foam quality. The effect of salt content on foam rheology was minimal. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

22 pages, 10365 KiB

Open AccessArticle

Use of Concentric Hele-Shaw Cell for the Study of Displacement Flow and Interface Tracking in Primary Cementing

by Amir Taheri, Jan David Ytrehus, Bjørnar Lund and Malin Torsæter

Energies 2021, 14(1), 51; https://doi.org/10.3390/en14010051 - 24 Dec 2020

Cited by 3 | Viewed by 1782

Abstract

We present our new designed concentric Hele-Shaw cell geometry with dynamic similarity to a real field wellbore annulus during primary cementing, and then, the results of displacement flow of Newtonian and yield-stress non-Newtonian fluids in it are described. The displacement stability and efficiency, [...] Read more.

We present our new designed concentric Hele-Shaw cell geometry with dynamic similarity to a real field wellbore annulus during primary cementing, and then, the results of displacement flow of Newtonian and yield-stress non-Newtonian fluids in it are described. The displacement stability and efficiency, the effect of back, front, and side boundaries on displacement, bypassing pockets of displaced yield-stress fluid in displacing fluid, and the behavior of pressure gradients in the cell are investigated. Applications of intermediate buoyant particles with different sizes and densities intermediate between those of successively pumped fluids for tracking the interface between the two displaced and displacing fluids are examined. The main idea is to upgrade this concentric Hele-Shaw cell geometry later to an eccentric one and check the possibility of tracking the interface between successive fluids pumped in the cell. Successful results help us track the interface between drilling fluid and spacer/cement during primary cementing in wells penetrating a CO₂ storage reservoir and decreasing the risk of CO₂ leakage from them. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

21 pages, 8916 KiB

Open AccessArticle

Effect of Iron Oxide Nanoparticles on the Properties of Water-Based Drilling Fluids

by Muhammad Awais Ashfaq Alvi, Mesfin Belayneh, Sulalit Bandyopadhyay and Mona Wetrhus Minde

Energies 2020, 13(24), 6718; https://doi.org/10.3390/en13246718 - 19 Dec 2020

Cited by 15 | Viewed by 2894

Abstract

In recent years, several studies have indicated the impact of nanoparticles (NPs) on various properties (such as viscosity and fluid loss) of conventional drilling fluids. Our previous study with commercial iron oxide NPs indicated the potential of using NPs to improve the properties [...] Read more.

In recent years, several studies have indicated the impact of nanoparticles (NPs) on various properties (such as viscosity and fluid loss) of conventional drilling fluids. Our previous study with commercial iron oxide NPs indicated the potential of using NPs to improve the properties of a laboratory bentonite-based drilling fluid without barite. In the present work, iron oxide NPs have been synthesized using the co-precipitation method. The effect of these hydrophilic NPs has been evaluated in bentonite and KCl-based drilling fluids. Rheological properties at different temperatures, viscoelastic properties, lubricity, and filtrate loss were measured to study the effect of NPs on the base fluid. Also, elemental analysis of the filtrate and microscale analysis of the filter cake was performed. Results for bentonite-based fluid showed that 0.019 wt% (0.1 g) of NPs reduced the coefficient of friction by 47%, and 0.0095 wt% (0.05 g) of NPs reduced the fluid loss by 20%. Moreover, for KCl-based fluids, 0.019 wt% (0.1 g) of additive reduced the coefficient of friction by 45%, while higher concentration of 0.038 wt% (0.2 g) of NPs shows 14% reduction in the filtrate loss. Microscale analysis shows that presence of NPs in the cake structure produces a more compact and less porous structure. This study indicates that very small concentration of NPs can provide better performance for the drilling fluids. Additionally, results from this work indicate the ability of NPs to fine-tune the properties of drilling fluids. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Graphical abstract

17 pages, 6184 KiB

Open AccessArticle

Experimental Research of Shale Pellet Swelling in Nano-Based Drilling Muds

by Borivoje Pašić, Nediljka Gaurina-Međimurec, Petar Mijić and Igor Medved

Energies 2020, 13(23), 6246; https://doi.org/10.3390/en13236246 - 26 Nov 2020

Cited by 10 | Viewed by 2686

Abstract

The drilling of clay-rich formations, such as shale, is an extremely demanding technical and technological process. Shale consists of mixed clay minerals in different ratios and in contact with water from drilling mud. It tends to swell and cause different wellbore instability problems. [...] Read more.

The drilling of clay-rich formations, such as shale, is an extremely demanding technical and technological process. Shale consists of mixed clay minerals in different ratios and in contact with water from drilling mud. It tends to swell and cause different wellbore instability problems. Usually, the petroleum industry uses various types of salt and/or polymers as shale hydration inhibitors. The aim of this research was to determine whether nanoparticles can be used as shale swelling inhibitors because due to their small size they can enter the shale nanopores, plug them and stop further penetration of mud filtrate into the shale formation. Swelling of bentonite-calcium carbonate pellets after 2 and 24 h in water and drilling mud (water, bentonite, PAC and NaOH) without nanoparticles and with addition of TiO₂ (0.5, 1 and 1.5 wt%) and SiO₂ (0.5, 1 and 1.5 wt%) nanoparticles was measured using a linear swell meter. Additionally, granulometric analyses of bentonite as well as the zeta potential of tested muds containing nanoparticles were performed. Based on the laboratory research, it can generally be concluded that the addition of SiO₂ and TiO₂ nanoparticles in water and base drilling mud reduces the swelling of pellets up to 40.06%. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

23 pages, 10326 KiB

Open AccessArticle

The Effect of Thixotropy on Pressure Losses in a Pipe

by Eric Cayeux and Amare Leulseged

Energies 2020, 13(23), 6165; https://doi.org/10.3390/en13236165 - 24 Nov 2020

Cited by 18 | Viewed by 2367

Abstract

Drilling fluids are designed to be shear-thinning for limiting pressure losses when subjected to high bulk velocities and yet be sufficiently viscous to transport solid material under low bulk velocity conditions. They also form a gel when left at rest, to keep weighting [...] Read more.

Drilling fluids are designed to be shear-thinning for limiting pressure losses when subjected to high bulk velocities and yet be sufficiently viscous to transport solid material under low bulk velocity conditions. They also form a gel when left at rest, to keep weighting materials and drill-cuttings in suspension. Because of this design, they also have a thixotropic behavior. As the shear history influences the shear properties of thixotropic fluids, the pressure losses experienced in a tube, after a change in diameter, are influenced over a much longer distance than just what would be expected from solely entrance effects. In this paper, we consider several rheological behaviors that are relevant for characterizing drilling fluids: Collins–Graves, Herschel–Bulkley, Robertson–Stiff, Heinz–Casson, Carreau and Quemada. We develop a generic solution for modelling the viscous pressure gradient in a circular pipe under the influence of thixotropic effects and we apply this model to configurations with change in diameters. It is found that the choice of a rheological behavior should be guided by the actual response of the fluid, especially in a turbulent flow regime, and not chosen a priori. Furthermore, thixotropy may influence pressure gradients over long distances when there are changes of diameter in a hydraulic circuit. This fact is important to consider when designing pipe rheometers. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

14 pages, 17678 KiB

Open AccessArticle

Systematic Experimental Investigation on In-Situ Self-Adaptive Sealing Property of Composite Pressure-Activated Sealant for Curing Minor Tubular Leaks

by Lin Xu, Xiaohe Huang, Xin Huang, Jie Xu, Xijin Xing, Mingbiao Xu, Chao Ma and Meilan Huang

Energies 2020, 13(21), 5597; https://doi.org/10.3390/en13215597 - 26 Oct 2020

Cited by 3 | Viewed by 2125

Abstract

Curing minor leaks and restoring the integrity of a wellbore in a safe and economical way is always challenging in oil and gas production. In this work, a composite pressure-activated sealant, combined with liquid and solid sealing materials, was prepared via the demulsification [...] Read more.

Curing minor leaks and restoring the integrity of a wellbore in a safe and economical way is always challenging in oil and gas production. In this work, a composite pressure-activated sealant, combined with liquid and solid sealing materials, was prepared via the demulsification approach. The structure, morphology, and size distribution of key particulates in the sealant were examined, and the in-situ self-adaptive sealing property was examined with a specially design dynamic sealing detector. The results indicated that the pressure-activated sealant was a multi-dispersed phase system, and the dispersed colloid particles were regular in shape and had a narrow size distribution of 300–400 μm. The solid sealing materials were introduced to construct a composite pressure-activated sealant, and the sealing capability can be markedly reinforced by cooperativity of liquid and solid sealing materials. A mechanochemical coupling model was put forward to rationalize the dynamic sealing process. Finally, such sealant system was employed in a certain offshore gas well with sustained casing pressure to verify its applicability in minor defect repairs. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

16 pages, 1795 KiB

Open AccessArticle

Viscosity Models for Drilling Fluids—Herschel-Bulkley Parameters and Their Use

by Arild Saasen and Jan David Ytrehus

Energies 2020, 13(20), 5271; https://doi.org/10.3390/en13205271 - 11 Oct 2020

Cited by 42 | Viewed by 5045

Abstract

An evaluation is presented of the practical usage of the Herschel-Bulkley viscosity model for drilling fluids. If data from automatic viscosity measurements exist, the parameters should be selected from relevant shear rate ranges to be applicable. To be able to be used properly, [...] Read more.

An evaluation is presented of the practical usage of the Herschel-Bulkley viscosity model for drilling fluids. If data from automatic viscosity measurements exist, the parameters should be selected from relevant shear rate ranges to be applicable. To be able to be used properly, viscosity measurements must be measured with a sufficient accuracy. It is shown that a manual reading of standard viscometers may yield insufficient accuracy. It is also shown that the use of yield point/plastic viscosity (YP/PV) as measured using API or ISO standards normally provide inaccurate viscosity parameters. The use of the Herschel-Bulkley model using dimensionless shear rates is more suitable than the traditional way of writing this model when the scope is to compare different drilling fluids. This approach makes it also easier to make correlations with thermodynamic quantities like pressure and temperature or chemical or mineralogical compositions of the drilling fluid. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

25 pages, 6762 KiB

Open AccessArticle

Experimental Methods for Investigation of Drilling Fluid Displacement in Irregular Annuli

by Bjørnar Lund, Ali Taghipour, Jan David Ytrehus and Arild Saasen

Energies 2020, 13(19), 5201; https://doi.org/10.3390/en13195201 - 6 Oct 2020

Cited by 4 | Viewed by 2023

Abstract

Experimental methods are still indispensable for fluid mechanics research, despite advancements in the modelling and computer simulation field. Experimental data are vital for validating simulations of complex flow systems. However, measuring the flow in industrially relevant systems can be difficult for several reasons. [...] Read more.

Experimental methods are still indispensable for fluid mechanics research, despite advancements in the modelling and computer simulation field. Experimental data are vital for validating simulations of complex flow systems. However, measuring the flow in industrially relevant systems can be difficult for several reasons. Here we address flow measurement challenges related to cementing of oil wells, where main experimental issues are related to opacity of the fluids and the sheer size of the system. The main objective is to track the propagation of a fluid-fluid interface during a two-fluid displacement process, and thereby to characterize the efficiency of the displacement process. We describe the implementation and use of an array of electrical conductivity probes, and demonstrate with examples how the signals can be used to recover relevant information about the displacement process. To our knowledge this is the most extensive use of this measurement method for studying displacement in a large-scale laboratory setup. Optical measurements and visual observations are challenging and/or costly in such large-scale systems, but can still provide qualitative information as shown in this article. Using electrical conductivity probes is a robust and fairly low-cost experimental method for characterizing fluid-fluid displacement in large-scale systems. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Graphical abstract

22 pages, 4850 KiB

Open AccessArticle

Experimental Investigation of Inhibitive Drilling Fluids Performance: Case Studies from United States Shale Basins

by Nabe Konate and Saeed Salehi

Energies 2020, 13(19), 5142; https://doi.org/10.3390/en13195142 - 2 Oct 2020

Cited by 6 | Viewed by 2441

Abstract

Shale formations are attractive prospects due to their potential in oil and gas production. Some of the largest shale formations in the mainland US, such as the Tuscaloosa Marine Shale (TMS), have reserves estimated to be around 7 billion barrels. Despite their huge [...] Read more.

Shale formations are attractive prospects due to their potential in oil and gas production. Some of the largest shale formations in the mainland US, such as the Tuscaloosa Marine Shale (TMS), have reserves estimated to be around 7 billion barrels. Despite their huge potential, shale formations present major concerns for drilling operators. These prospects have unique challenges because of all their alteration and incompatibility issues with drilling and completion fluids. Most shale formations undergo numerous chemical and physical alterations, making their interaction with the drilling and completion fluid systems very complex to understand. In this study, a high-pressure, high-temperature (HPHT) drilling simulator was used to mimic real time drilling operations to investigate the performance of inhibitive drilling fluid systems in two major shale formations (Eagle Ford Shale and Tuscaloosa Marine Shale). A series of drilling experiments using the drilling simulator and clay swelling tests were conducted to evaluate the drilling performance of the KCl drilling fluid and cesium formate brine systems and their effectiveness in minimizing drilling concerns. Cylindrical cores were used to mimic vertical wellbores. It was found that the inhibitive muds systems (KCl and cesium formate) provided improved drilling performance compared to conventional fluid systems. Among the inhibitive systems, the cesium formate brine showed the best drilling performances due to its low swelling rate and improved drilling performance. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Figure 1

14 pages, 6193 KiB

Open AccessArticle

Application of Microemulsion Systems in the Formulation of Biodegradable Pre-Flush Fluid for Primary Cementing

by Elayne A. Araújo, Thaine T. Caminha, Evanice M. Paiva, Raphael R. Silva, Júlio Cézar O. Freitas, Alfredo Ismael C. Garnica and Fabíola D. S. Curbelo

Energies 2020, 13(18), 4683; https://doi.org/10.3390/en13184683 - 9 Sep 2020

Cited by 1 | Viewed by 2523

Abstract

Oil well cleanup fluids (pre-flushes) are intermediate fluids pumped ahead of the cement slurry; they are able to clean the well walls by removing the filter cake formed by the drilling fluid, and leave the surface water-wet. This work’s main objective was to [...] Read more.

Oil well cleanup fluids (pre-flushes) are intermediate fluids pumped ahead of the cement slurry; they are able to clean the well walls by removing the filter cake formed by the drilling fluid, and leave the surface water-wet. This work’s main objective was to use biodegradable microemulsion systems as cleanup fluids in order to reduce the environmental impact. Three microemulsion systems were formulated, each composed of an oil phase, a surfactant and three different aqueous phases: glycerol, glycerol:water (mass ratio 1:1), and fresh water. The results show that all microemulsion systems were effective with 100% filter cake removal, with a removal time of less than 60 s. The wettability test and fluid compatibility analyses exhibited advantageous performances, without phase separation, variations in viscosity, gelation, or flocculation. The compressive strength and X-ray diffractometry (XRD) analysis showed the influence of the glycerol on the cement slurry properties, with the compressive strength resistance ranging from 8.0 to 10.7 MPa, and resulted in the formation of portlandite. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Graphical abstract

20 pages, 7528 KiB

Open AccessArticle

Effect of the Particle Size on the Near-Wall Turbulence Characteristics of the Polymer Fluid Flow and the Critical Velocity Required for Particle Removal from the Sand Bed Deposited in Horizontal Wells

by Mehmet Meric Hirpa, Sumanth Kumar Arnipally and Ergun Kuru

Energies 2020, 13(12), 3172; https://doi.org/10.3390/en13123172 - 18 Jun 2020

Cited by 5 | Viewed by 2435

Abstract

Water-based polymer drilling fluids are commonly used for drilling long horizontal wells where eliminating the drilling fluid-related formation damage and minimizing the environmental impact of the drilling fluids are the main concerns. An experimental study was conducted to investigate the turbulent flow of [...] Read more.

Water-based polymer drilling fluids are commonly used for drilling long horizontal wells where eliminating the drilling fluid-related formation damage and minimizing the environmental impact of the drilling fluids are the main concerns. An experimental study was conducted to investigate the turbulent flow of a polymer fluid over a stationary sand bed deposited in a horizontal pipeline. The main objectives of the study were to determine the effects of sand particle size on the critical velocity required for the onset of the bed erosion and the near-wall turbulence characteristics of the polymer fluid flow over the sand bed. Industrial sand particles having three different size ranges (20/40, 30/50, 40/70) were used for the experiments. The particle image velocimetry (PIV) technique was used to determine instantaneous local velocity distributions and near-wall turbulence characteristics (such as Reynolds stress, axial and turbulence intensity profiles) of the polymer fluid flow over the stationary sand bed under turbulent flow conditions. The critical velocity for the onset of the particle removal from a stationary sand bed using a polymer fluid flow was affected by the sand particle size. The critical velocity required for the particle removal from the bed deposits did not change monotonously with the changing particle size. When polymer fluids were used for hole cleaning, the particle size effect on the critical velocity varied (i.e., critical velocity increased or decreased) depending on the relative comparison of the sand particle size with respect to the thickness of the viscous sublayer under turbulent flow condition. Full article

(This article belongs to the Special Issue Advances in Drilling Fluid Technology)

► Show Figures

Graphical abstract

Journal Menu

Journal Browser

Advances in Drilling Fluid Technology

Share This Special Issue

Special Issue Editor

Special Issue Information

Keywords

Published Papers (15 papers)

Research

Further Information

Guidelines

MDPI Initiatives

Follow MDPI