Next Article in Journal
Electro-Optical Characteristics of Solution-Derived Zinc Oxide Film According to Number of Rubbing Iterations for Liquid Crystal Alignment
Next Article in Special Issue
Design of Tunable Liquid Crystal Lenses with a Parabolic Phase Profile
Previous Article in Journal
A Comparative Study of Microstructure and Hot Deformability of a Fe–Al–Ta Iron Aluminide Prepared via Additive Manufacturing and Conventional Casting
Previous Article in Special Issue
End-of-Life Liquid Crystal Displays Recycling: Physico-Chemical Properties of Recovered Liquid Crystals
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Synthesis, Mesomorphic Properties and Application of (R,S)-1-Methylpentyl 4′-Hydroxybiphenyl-4-carboxylate Derivatives

Institute of Chemistry, Military University of Technology, 00-908 Warsaw, Poland
*
Author to whom correspondence should be addressed.
Crystals 2022, 12(12), 1710; https://doi.org/10.3390/cryst12121710
Submission received: 11 October 2022 / Revised: 17 November 2022 / Accepted: 23 November 2022 / Published: 25 November 2022
(This article belongs to the Special Issue Advances in Liquid Crystal Optical Devices)

Abstract

:
Thirteen new liquid crystalline racemic mixtures were synthesized and investigated. For these racemic mixtures, the phase sequences and their changes were determined by polarizing optical microscopy (POM). The phase transition temperatures and transition enthalpies were checked by differential scanning calorimetry (DSC). All new racemates have an anticlinic smectic CA phase in a broad temperature range. Three highly tilted antiferroelectric mixtures were doped with six racemates at a concentration of 20% by weight. The helical pitch of the prepared mixtures was measured by the spectrophotometry method. All doped mixtures have a longer helical pitch than the base mixtures.

1. Introduction

The racemic mixture, also called racemate, is the mixture of equal quantities of two enantiomers or substances that have dissymmetric molecular structures, i.e., mirror images of one another (Figure 1). Each enantiomer rotates the plane of polarization of plane-polarized light through a characteristic angle, but because the rotatory effect of each component exactly cancels that of the other, the racemic mixture is optically inactive [1,2].
The racemates can be used as dopants for the liquid crystalline mixtures, improving some of their properties, such as the antiferroelectric phase range, the helical pitch length, the reduction of the rotational viscosity, the decrease of the values of the spontaneous polarization, etc. [3,4,5]. Liquid crystalline mixtures are widely used in optical devices; therefore, new materials are constantly being developed for this purpose [6,7,8,9,10,11]. The use of the racemates also leads to a reduction in the preparation costs of the liquid crystalline mixtures. They can also be separated by chiral chromatography (HPLC, UPLC, SFC) [12,13,14,15,16,17,18,19].
Herein, thirteen new racemic mixtures with the acronym: n.(X1X2) (R,S) and the general formula shown in Figure 2a are synthesized, and their mesomorphic and thermodynamic properties are measured and discussed.
Six of the racemates are used as dopants for three highly tilted antiferroelectric liquid crystalline mixtures. The base mixtures are described in Refs. [20,21]. All the components of the base mixtures are (S) enantiomers belonging to the same homologous series. The aim of the work is to discuss the mesomorphic properties of the racemates with a wide-temperature anticlinic phase and to demonstrate the advisability of using the racemates as dopants for the antiferroelectric mixtures. If so, it would be possible to extend the range of the antiferroelectric phase and thus increase the helical pitch, which is quite sensitive to doping [3,4,22,23,24,25]. An analysis of the obtained results is presented.

2. Synthesis of the Racemic Mixtures

In this work, thirteen previously unpublished racemates were synthesized by treating (R,S) 4′-(1-methylpentyloxycarbonyl)biphenol with benzoic acid chloride, see Figure 2b. The synthesis of the racemates was carried out as described in Ref. [3]. The benzoic acids were synthesized using the method described in Ref. [26].
For the synthesis of (R,S) 4′-(1-methylpentyloxycarbonyl)biphenol, the method described in Ref. [27] was chosen. The commercially available (R,S)-2-hexanol was used for the synthesis.
The purity of the synthesized racemates was checked using a Shimadzu prominence chromatograph with an SPD-M20A diode array detector. The purity of the racemates was also monitored by thin-layer chromatography (silica gel on aluminum).
The purity of the racemates, determined by HPLC, is shown in Table 1. About 1 g of the final racemates were synthesized in all cases. The purity is 99% or more.
The structure of the racemic mixtures was confirmed by 1H NMR and 13C NMR nuclear magnetic resonance. The NMR spectra were acquired on a Bruker Avance III 500 MHz spectrometer. This device has a superconducting magnet, which generates a magnetic field at induction 11.75 T, and for the sample radiation effects at a frequency of 500 MHz for protons and 125 MHz for carbon nuclei. The deuterated chloroform (CDCl3) as the solvent was used. The spectra of all of the samples were measured at 25 °C.
The 1H NMR and 13C NMR spectra of all racemates were added to the Supplementary Materials (Figures S1–S26). Details of the basic chemical characterization of the new racemates are presented below (the acronyms of the racemates are used).
2.(HH) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.66 (m, -CH2-); 1.78 (m, -CH2-); 4.06 (t, -CH2-); 4.13 (t, -CH2-); 4.06-4.27 (t, -CH2-); 5.21 (sext, -CH-), 7.02 (d, CArH), 7.34 (d, CArH), 7.68 (q, CArH), 8.15 (dd, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3); 22.6 (s, CH2), 27.6 (s, CH2), 35.8 (s, CH2), 67.6 (s, CH2), 68.2 (t, CF), 71.2 (s, CH2), 71.8 (s, CH), 114.4 (s, CArH), 122.2 (s, CArH), 122.3 (s, CAr), 126.9 (s, CArH), 128.3 (s, CArH), 129.8 (s, CAr), 130.1 (s, CArH), 132.4 (s, CArH), 137.8 (s, CAr), 144.6 (s, CAr), 151.1 (s, CAr), 162.9 (s, CAr), 164.8 (s, CAr), 166.1 (s, CAr).
2.(HF) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.61 (m, -CH2-); 1.78 (m, -CH2-); 4.06 (t, -CH2-); 4.12 (t, -CF-); 4.25 (t, -CH2-); 5.22 (sext, -CH-), 6.77 (dd, CArH), 7.35 (d, CArH), 7.68 (q, CArH), 8.09 (s, CArH), 8.11 (s, CArH), 8.13 (s, CArH), 8.14 (s, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3); 22.6 (s, CH2), 27.6 (s, CH2), 35.8 (s, CH2), 67.9 (s, CH2), 68.2 (t, CF), 71.0 (s, CH), 71.8 (s, CH), 103.1 (d, CArF), 110,6 (d, CArF), 110.8 (d, CArF), 122.2 (s, CArH), 126.9 (s, CArH), 128.3 (s, CArH), 129.8 (s, CAr), 130.1 (s, CArH), 134.0 (s, CAr), 137.9 (s, CAr), 144.6 (s, CAr), 150.8 (s, CAr), 162.3 (s, CAr), 162.4 (s, CAr), 164.0 (d, CF), 164.9 (s, CAr), 166.1 (s, CAr).
2.(FH) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3); 1.38 (d, -CH2-); 1.66 (m, -CH2-); 1.78 (m, -CH2-), 4.09 (t, -CH2-), 4.16 (t, -CH2-), 4.35 (t, -CH2-), 5.22 (sext, -CH-); 7.09 (t, CArH), 7.32 (d, CArH), 7.69 (t, CArH), 7.95–8.02 (dd, CArH); 8.13 (d, CArH).
13C {1H} NMR [ppm]: 13.9 (s, CH3); 20.1 (s, CH3), 22.6–35.8 (s, CH2), 68.4 (t, CF); 69.0 (s, CH); 71.1 (s, CH); 71.8 (s, CH); 122.2 (s, CArH), 122.7 (d, CArF), 126.9 (s, CArH), 127.4 (d, CArF), 150.9 (d, CArF), 151.2 (d, CArF), 152.9 (s, CAr), 163.0 (d, CArF), 166.0 (s, CAr).
3.(HF) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3); 1.38 (d, -CH2-); 1.65 (m, -CH2-); 1.78 (m, -CH2-); 2.15 (m, -CH2-); 3.83 (t, -CH2-); 3.98 (t, -CH2-); 4.17 (t, -CH2-); 5.21 (sext, -CH-); 6.7–6.9 (dd, CArH); 7.34 (d, CArH), 7.68 (q, CArH), 8.09 (t, CArH), 8.13 (d, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3), 22.6–35.8 (s, CH2); 64.9 (s, CH2); 67.8 (t, CF), 69.1 (s, CH); 71.8 (s, CH); 102.9 (d, CF), 110.1 (d, CArF); 110.7 (d, CArF); 162.4 (d, CArF); 162.9 (s, CAr), 164.5 (d, CArF), 165.0 (s, CAr), 166.1 (s, CAr).
3.(FF) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.66 (m, -CH2-); 1.78 (m, -CH2-); 2.19 (sext, -CH-), 3.86 (t, -CH2-), 3.99 (t, -CH2-), 4.28 (t, -CH2-), 5.21 (sext, -CH-), 6.88 (t, CArH); 7.34 (d, CArH); 7.69 (t, CArH); 7.90 (t, CArH); 8.13 (d, CArH).
13C {1H} NMR [ppm]: 13.9 (s, CH3); 20.1 (s, CH3); 22.6–35.8 (s, CH2), 66.0 (s, CH2), 67.8 (t, CH), 68.8 (s, CH2), 71.8 (s, CH), 108.5 (s, CArH), 122.2 (s, CArH), 126.9 (s, CArH), 127.1 (d, CArF), 128.4 (s, CArH), 129.9 (s, CArH), 130.1 (s, CArH), 138.1 (s, CArH), 140.4 (dd, CArF), 144.5 (s, CAr), 150.6 (s, CAr), 150.8 (d, CArF), 161.9 (s, CAr), 166.0 (s, CAr).
4.(HH) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.66 (m, -CH2-); 1.78 (m, -CH2-); 1.85 (m, -CH2-); 1.96 (m, -CH2-); 3.72 (t, -CH2-); 3.97 (t, -CH2-); 4.11 (t, -CH2-); 5.21 (sext, -CH-), 7.00 (d, CArH), 7.33 (d, CArH), 7.69 (q, CArH), 8.13 (d, CArH), 8.18 (d, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3); 22.6 (s, CH2), 25.7 (s, CH2), 26.2 (s, CH2), 27.6 (s, CH2), 35.8 (s, CH2), 67.8 (s, CH2), 71.8 (s, CH), 72.6 (s, CH), 114.3 (s, CArH), 121.6 (s, CAr), 122.3 (s, CArH), 126.9 (s, CArH), 128.3 (s, CArH), 129.7 (s, CAr), 130.1 (s, CArH), 132.4 (s, CArH), 137.6 (s, CAr), 144.6 (s, CAr), 151.2 (s, CAr), 163.5 (s, CAr), 164.9 (s, CAr), 166.1 (s, CAr).
4.(HF) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.66 (m, -CH2-); 1.82 (m, -CH2-), 1.96 1.82 (m, -CH2-), 3.71 1.82 (t, -CH2-), 3.96 1.82 (t, -CH2-), 4.08 1.82 (m, -CH2-), 5.20 (sext, -CH-), 6.70 (dd, CArH), 6.81 (dd, CArH), 7.33 (d, CArH), 7.67 (q, CArH), 8.08 (t, CArH), 8.13 (d, CArH).
13C {1H} NMR [ppm]: 13.9 (s, CH3); 20.0 (s, CH3); 22.6 (s, CH2); 25.6 (s, CH2); 26.1 (s, CH2); 27.6 (s, CH2); 35.8 (s, CH2); 67.6 (t, CF); 68.3 (s, CH2); 71.8 (s, CH); 72.6 (s, CH); 102.8 (d, CF); 109.8 (d, CF); 110.8 (d, CF); 122.3 (s, CArH), 126.9 (s, CArH), 128.3 (s, CArH), 129.7 (s, CAr), 130.1 (s, CArH), 133.9 (s, CAr), 137.8 (s, CAr), 144.6 (s, CAr), 150.8 (s, CAr), 162.4 (d, CArF), 162.9 (s, CAr), 164.7 (d, CArF), 165.0 (s, CAr), 166.1 (s, CAr).
5.(HH) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.63 (m, -CH2-); 1.74 (m, -CH2-); 1.89 (sext, -CH-), 3.67 (t, -CH2-); 3.95 (t, -CH2-); 4.09 (t, -CH2-); 5.20 (sext, -CH-), 7.00 (d, CArH), 7.32 (d, CArH), 7.68 (q, CArH), 8.13 (d, CArH), 8.18 (d, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3); 22.4 (s, CH2), 22.6 (s, CH2), 27.6 (s, CH2), 28.8 (s, CH2), 29.2 (s, CH2), 35.8 (s, CH2), 67.3 (t, CF), 68.0 (s, CH2), 71.8 (s, CH), 72.9 (s, CH), 114.3 (s, CArH), 121.5 (s, CAr), 122.3 (s, CArH), 126.9 (s, CArH), 128.3 (s, CArH), 129.7 (s, CAr), 130.1 (s, CArH), 132.4 (s, CArH), 137.7 (s, CAr), 144.6 (s, CAr), 151.2 (s, CAr), 163.5 (s, CAr), 164.9 (s, CAr), 166.1 (s, CAr).
5.(FH) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.64 (m, -CH2-); 1.74 (m, -CH2-); 1.93 (m, -CH2-); 3.67 (t, -CH2-); 3.95 (t, -CF-); 4.16 (t, -CH2-); 5.21 (sext, -CH-), 7.06 (t, CArH), 7.31 (d, CArH), 7.68 (t, CArH), 7.93 (dd, CArH), 8.00 (d, CArH), 8.13 (d, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3); 22.3 (s, CH2), 22.6 (s, CH2), 27.6 (s, CH2), 28.7 (s, CH2), 29.2 (s, CH2), 35.8 (s, CH2), 67.6 (t, CF), 69.2 (s, CH2), 71.8 (s, CH), 72.9 (s, CH), 113.4 (s, CAr), 117.8 (d, CArF), 121.8 (s, CArF), 121.9 (s, CArH), 126.9 (s, CArH), 127.4 (d, CArF), 128.4 (s, CArH), 129.8 (s, CAr), 130.1 (s, CArH), 137.9 (s, CAr), 144.5 (s, CAr), 150.9 (s, CArH), 151.8 (d, CArF), 152.9 (s, CAr), 164.0 (d, CAr), 166.0 (s, CAr).
5.(FF) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.62 (m, -CH2-); 1.75 (m, -CH2-); 1.94 (m, -CH2-); 3.67 (t, -CH2-); 3.83 (t, -CH2-); 4.18 (t, -CH2-), 5.21 (sext, -CH-); 6.85 (t, CArH); 7.36 (d, CArH), 7.69 (t, CArH); 7.89 (t, CArH), 8.13 (d, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3), 22.3–35.8 (s, CH2); 67.6 (t, CF), 69.7 (s, CH); 71.8 (s, CH); 72.9 (s, CH); 108.4 (s, CH), 111.3 (d, CArF), 122.2 (s, CArH), 126.9 (s, CArH), 127.0 (d, CArF), 129.9 (s, CArH), 130.1 (s, CArH), 138.0 (s, CAr), 144.5 (s, CAr), 150.6 (s, CAr).
6.(FH) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.50 (m, -CH2-); 1.56 (m, -CH2-), 1.67 (m, -CH2-); 1.78 (m, -CH2-); 1.91 (m, -CH2-); 3.64 (t, -CH2-); 3.94 (t, -CH2-); 4.15 (t, -CH2-); 5.20 (sext, -CH-), 7.06 (t, CArH), 7.31 (d, CArH), 7.69 (q, CArH), 7.93 (dd, CArH), 7.99 (d, CArH), 8.13 (d, CArH).
13C {1H} NMR [ppm]: 13.9 (s, CH3); 20.1 (s, CH3); 22.6 (s, CH2); 25.5 (d, CF); 27.6 (s, CH2); 28.9 (s, CH2); 29.3 (s, CH2); 35.8 (s, CH2), 67.6 (t, CF), 69.2 (s, CH2), 71.8 (s, CH), 73.0 (s, CH), 113.5 (s, CAr), 117.7 (d, CArF), 121.7 (s, CArF), 122.2 (s, CArH), 126.9 (s, CArH), 127.4 (s, CAr), 128.4 (s, CArH), 129.8 (s, CAr), 130.1 (s, CArH), 137.9 (s, CAr), 144.5 (s, CAr), 150.9 (d, CF), 151.9 (d, CF), 152.9 (s, CAr), 164.0 (d, CF), 166.0 (s, CAr).
6.(FF) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.48 (m, -CH2-); 1.55 (m, -CH2-), 1.66 (m, -CH2-), 1.78 (m, -CH2-), 1.91 (quin, -CH2-); 3.64 (t, -CH2-); 3.94 (t, -CH2-); 4.16 (t, -CH2-); 5.20 (sext, -CH-), 6.86 (t, CArH), 7.3 (d, CArH), 7.69 (t, CArH), 7.88 (t, CArH), 8.13 (d, CArH).
13C {1H} NMR [ppm]: 13.9 (s, CH3); 20.1 (s, CH3); 22.6 (s, CH2); 25.5 (d, CF); 27.6 (s, CH2); 28.8 (s, CH2); 29.3 (s, CH2); 35.8 (s, CH2); 67.6 (t, CF); 69.8 (s, CH2); 71.8 (s, CH), 72.9 (s, CH), 108.5 (s, C), 111.2 (d, CF), 122.1 (s, CArH), 126.9 (s, CArH), 127.04 (s, CAr), 128.4 (s, CArH),129.9 (s, CAr), 130.1 (s, CArH), 138.0 (s, CAr), 140.5 (d, CF), 142.5 (d, CArF), 144.5 (s, CAr), 150.7 (s, CAr), 153.1 (s, CAr), 161.9 (s, CAr), 166.0 (s, CAr).
7.(HH) (R,S)
1H NMR [ppm]: 0.94 (t, -CH3), 1.39 (d, -CH2-); 1.52 (m, -CH2-); 1.66 (m, -CH2-); 1.78 (m, -CH2-); 1.85 (sext, -CH-), 3.62 (t, -CH2-); 3.94 (t, -CH2-); 4.07 (t, -CH2-); 5.21 (sext, -CH-), 7.00 (d, CArH), 7.32 (d, CArH),7.69 (q, CArH), 1.18 (d, CArH), 8.19 (d, CArH).
13C {1H} NMR [ppm]: 14.0 (s, CH3); 20.1 (s, CH3); 22.6 (s, CH2), 25.7 (s, CH2), 25.9 (s, CH2), 27.6 (s, CH2), 29.0 (d, CF), 29.4 (s, CH2), 35.8 (s, CH2), 67.6 (t, CF), 68.2 (s, CF), 71.8 (s, CH), 73.1 (s, CH), 114.3 (s, CArH), 121.4 114.4 (s, CAr), 122.3 (s, CArH), 128.3 (s, CArH), 129.8 (s, CAr), 130.1 (s, CArH), 132.3 (s, CArH), 137.7 (s, CAr), 144.6 (s, CAr), 151.2 (s, CAr), 163.6 (s, CAr), 164.9 (s, CAr), 166.0 (s, CAr).

3. Measurements

The mesomorphic properties of the racemates and the prepared mixtures were investigated using a polarizing optical microscopy technique. An OLYMPUS BX51 polarizing optical microscope equipped with a Linkam THMS-600 hot stage and a temperature controller TMS-93 were used. The phase sequences and the phase transition temperatures were determined by observation of the characteristic textures and their changes. In addition, differential scanning calorimetry (DSC) measurements were carried out using a Netzsch DSC 204 F1 Phoenix calorimeter. These measurements were performed in a nitrogen atmosphere under 2 °C·min−1 heating and cooling rate.
The helical pitch (p) value measurements were based on the phenomenon of wavelength-dependent selective reflection of light [28]. The selective reflection wavelength was determined in the temperature range of the tilted chiral smectic phases on samples placed on a glass plate coated with a surfactant-promoting homeotropic orientation of the molecular director on the substrate glass plate. The other surface of the smectic slab was left free, which also assures the homeotropic orientation at the air-LC contact boundary. The experimental details have been reported elsewhere [29,30]. The helical pitch was calculated according to Equations (1) and (2) for the antiferroelectric and ferroelectric phases, respectively.
λ max = n p
λ max = 2 n p
Here λmax is the wavelength at the center of the selective reflection waveband. The value of n = 1.5 was taken for the calculation [31,32]. The transmission spectra were acquired using a Shimadzu UV-VIS-NIR spectrometer UV-3600 at the wavelength range of 360–3000 nm. All the observations of the selective reflection spectra were carried out during the cooling cycle. An MLWU7 temperature controller with a Peltier element was used to drive the temperature within the range of 2–110 °C, with an accuracy of ±0.1 °C.

4. Mesomorphic Properties of the Racemic Mixtures

For the synthesized racemic mixtures, the phase sequences and the phase transition temperatures are summarized in Table 2 and visualized in Figure 3. The textures for the observed phases (the smectic A phase, the smectic C phase and the smectic CA phase) are shown in Figure 4a–c.
All racemates have the anticlinic smectic phase in a broad temperature range. The broadest range of this phase is observed for the unsubstituted racemate with the oligomethylene spacer equal to 4 (above 87 °C). For four of the racemates, the direct transition from the SmCA phase to the isotropic phase is observed. Such properties occur for the racemates with a substitution of the (HF) and (HH) type and a short oligomethylene spacer (n = 2, 3, 4). It has been found that the direct SmCA-Iso phase transition in the liquid crystalline materials is beneficial for improving the alignment in the electro-optical cell [33,34,35]. The SmC and SmA phases are observed in a short or medium temperature range. The unsubstituted racemates have the highest clearing points. The melting points change irregularly; the lowest temperature is observed for the racemate with the longest oligomethylene spacer (36 °C).

5. Mixtures Compositions and Their Properties

Six racemic mixtures were used as dopants to formulate new multicomponent antiferroelectric mixtures. For the six prepared doped mixtures, the temperatures and enthalpies of the phase transitions, as well as the helical pitch, were examined. The three base mixtures selected for the study, with the acronyms W-458, W-459 and W-460, differ in the number of each doping components. All these mixtures have already been examined for their mesomorphic and thermodynamic properties, as well as the helical pitch [20,21]; therefore, it was possible to analyze the influence of the racemic mixtures on their properties. The base mixtures are characterized by very high values of the tilt angle of the molecules above 40° at lower temperatures. Six new mixtures with the racemic dopants at 20 wt% concentration were prepared (see Table 3).
The phase transition temperatures for the prepared mixtures are summarized in Table 4 and visualized in Figure 5 (comparing them with the base mixtures).
All doped mixtures have the antiferroelectric phase (SmCA*) in a very broad temperature range. The antiferroelectric phase range exceeds 70 °C for each of the doped mixtures. The broadest range of this phase is shown by the mixtures W-458B and W-460A doped with the racemic mixtures with the direct SmCA-Iso phase transition with the acronyms 3.HF (R,S) and 4.HF (R,S). The ferroelectric phase (SmC*) is present in all doped mixtures in a medium or a broad temperature range. The broadest range of this phase is shown by the mixtures W-458A and W-458B (23 and 17 degrees Celsius, respectively). The smectic A* phase occurs in a short temperature range in the mixtures W-458A, W-458B and W-460B.
All doped mixtures have higher clearing points than the base mixtures. None of the doped mixtures crystallized, and the DSC measurements were carried out from −15 °C.
The comparison of the helical pitch versus temperature for the base mixtures and the doped mixtures is shown in Figure 6a–c.
As could be expected (and of benefit), the doped mixtures are characterized by a longer helical pitch than the base mixture in both chiral phases. In the antiferroelectric phase, the helical pitch increases with increasing temperature, while in the ferroelectric phase, the helical pitch practically does not change upon heating, and it is very short (below 250 nm). The helical pitch in the SmCA* phase reaches maximum values above 1400 nm for the mixtures W-460A and W-460B, while for the mixture W-460B, it occurs at a lower temperature.

6. Conclusions

The newly synthesized racemates exhibit a wide temperature range for the anticlinic smectic CA phase and are promising components of the liquid crystalline mixtures. The synclinic smectic C phase and smectic A phase in these racemates depend on the length of the oligomethylene spacer and the substitution of the benzene ring. The widest temperature range of the SmCA phase is observed for the unsubstituted racemic mixtures.
The direct SmCA-Iso transition is observed for the racemic mixtures with a short oligomethylene spacer: 2.(HH) (R,S), 2.(HF) (R,S), 3.(HF) (R,S) and 4.(HF) (R,S). The SmC and SmA phases occur in a short or medium temperature range. New racemic mixtures can also be used as dopants which increase the helical pitch values and extend the temperature range of the SmCA* phase in the highly tilted antiferroelectric mixtures.
The mixtures doped with the racemates have favorable physical and electro-optical properties, as previously shown in Refs. [3,4,5]. In the next step, the measurements of the tilt angle of the molecules and the spontaneous polarization for the doped mixtures will be carried out.
It is also planned to develop the compositions of the other antiferroelectric liquid crystalline mixtures, based on the synthesized racemates, and separate the racemates into enantiomers by chiral liquid chromatography [36,37,38,39,40].

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/cryst12121710/s1, Figures S1–S26: The NMR spectra of all racemic mixtures.

Author Contributions

Conceptualization, M.U.; methodology, M.U.; software, M.U.; resources, M.U. and M.S.; investigation, M.U. and M.S.; data curation, M.U.; writing-original draft preparation, M.U.; writing-review and editing, M.U. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the National Science Center Grant—the Miniatura 5 entitled “Optimization of the separation of liquid crystalline racemic mixtures on chiral columns by high performance liquid chromatography” (DEC-2021/05/X/ST4/0016) and University Research Grant (UGB 796/2022).

Data Availability Statement

The data presented in this study are available on request from the corresponding author.

Acknowledgments

The authors want to thank Bartłomiej Dębicki for his help in the measurements for the doped mixtures.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Gautier, R.; Klingsporn, J.M.; Van Duyne, R.P.; Poeppelmeier, K.R. Optical activity from racemates. Nat. Mater. 2016, 15, 591–592. [Google Scholar] [CrossRef] [PubMed]
  2. Karnik, A.; Hasan, M. Stereochemistry. A Three-Dimensional Insight, 1st ed.; Elsevier: Amsterdam, The Netherlands, 2021. [Google Scholar]
  3. Urbańska, M.; Dziaduszek, J.; Strzeżysz, O.; Szala, M. Synclinic and anticlinic properties of (R,S) 4′-(1-methylheptyloxycarbonyl)biphenyl-4-yl 4-[7-(2,2,3,3,4,4,4-heptafluorobutoxy)heptyl-1-oxy]benzoates. Phase Transit. 2019, 92, 657–666. [Google Scholar] [CrossRef]
  4. Morawiak, P.; Żurowska, M.; Piecek, W. A long-pitch orthoconic antiferroelectric mixture modified by isomeric and racemic homostructural dopants. Liq. Cryst. 2018, 45, 1451–1459. [Google Scholar] [CrossRef]
  5. Ogrodnik, K.; Perkowski, P.; Raszewski, Z.; Piecek, W.; Żurowska, M.; Dabrowski, R.; Jaroszewicz, L. Dielectric measurements of orthoconic antiferroelectric liquid crystal mixtures. Mol. Cryst. Liq. Cryst. 2011, 547, 54–64. [Google Scholar] [CrossRef]
  6. Urbańska, M.; Morawiak, P.; Czerwiński, M. Effect of doping by enantiomers with the different absolute configuration and phase sequence on mesomorphic, helical and electro-optical properties of highly tilted chiral anticlinic mixture. J. Mol. Liq. 2020, 309, 113141. [Google Scholar] [CrossRef]
  7. Czerwiński, M.; Tykarska, M.; Kula, P. New ferroelectric liquid crystalline materials with properties suitable for surface stabilized and deformed helix effects. Liq. Cryst. Appl. 2021, 21, 61–73. [Google Scholar] [CrossRef]
  8. Nepal, S.; Das, B.; Das, M.K.; Das Sarkar, M.; Urbańska, M.; Czerwiński, M. Static permittivity and electro-optical properties of bi-component orthoconic antiferroelectric liquid crystalline mixtures targeted for polymer stabilized sensing systems. Polymers 2022, 14, 956. [Google Scholar] [CrossRef] [PubMed]
  9. Chakraborty, S.; Das, M.K.; Bubnov, A.; Weissflog, W.; Węgłowska, D.; Dabrowski, R. Induced frustrated twist grain boundary liquid crystalline phases in binary mixtures of achiral hockey stick-shaped and chiral rod-like materials. J. Mater. Chem. C 2019, 7, 10530–10543. [Google Scholar] [CrossRef]
  10. Tykarska, M.; Kurp, K.; Zieja, P.; Herman, J.; Stulov, S.; Bubnov, A. New quaterphenyls laterally substituted by methyl group and their influence on the self-assembling behaviour of ferroelectric bicomponent mixtures. Liq. Cryst. 2022, 49, 821–835. [Google Scholar] [CrossRef]
  11. Debnath, A.; Mandal, P.K. Effect of fluorination on the phase sequence, dielectric and electro-optical properties of ferroelectric and antiferroelectric mixtures. Liq. Cryst. 2017, 44, 2192–2202. [Google Scholar] [CrossRef]
  12. Vojtylová, T.; Kaspar, M.; Hamplová, V.; Novotná, V.; Sýkora, D. Chiral HPLC for a study of the optical purity of new liquid crystalline materials derived from lactic acid. Phase Transit. 2014, 87, 758–769. [Google Scholar] [CrossRef]
  13. Vaňkátová, P.; Šrolerová, T.; Kubíčková, A.; Kalíková, K. Fast UHPLC enantioseparation of liquid crystalline materials with chiral center based on octanol in reversed-phase and polar organic mode. Mon. Für Chem. Chem. Mon. 2020, 151, 1235–1240. [Google Scholar] [CrossRef]
  14. Vaňkátová, P.; Kalíková, K.; Kubíčková, A. Ultra-performance supercritical fluid chromatography: A powerful tool for the enantioseparation of thermotropic fluorinated liquid crystals. Anal. Chim. Acta 2018, 1038, 191–197. [Google Scholar] [CrossRef] [PubMed]
  15. Urbańska, M.; Vaňkátová, P.; Kubíčková, A.; Kalíková, K. Synthesis, characterisation and supercritical fluid chromatography enantioseparation of new liquid crystalline materials. Liq. Cryst. 2020, 47, 1832–1843. [Google Scholar] [CrossRef]
  16. Vojtylová-Jurkovičová, T.; Vaňkátová, P.; Urbańska, M.; Hamplová, V.; Sýkora, D.; Bubnov, A. Effective control of optical purity by chiral HPLC separation for ester-based liquid crystalline materials forming anticlinic smectic phases. Liq. Cryst. 2020, 48, 43–53. [Google Scholar] [CrossRef]
  17. Vaňkátová, P.; Kubíčková, A.; Cigl, M.; Kalíková, K. Ultra-performance chromatographic methods for enantioseparation of liquid crystals based on lactic acid. J. Supercrit. Fluids 2019, 146, 217–225. [Google Scholar] [CrossRef]
  18. Vaňkátová, P.; Kubíčková, A.; Kalíková, K. Enantioseparation of liquid crystals and their utilization as enantiodiscrimination materials. J. Chromatogr. A 2022, 1673, 463074. [Google Scholar] [CrossRef]
  19. Vojtylová, T.; Hamplová, V.; Galewski, Z.; Korbecka, I.; Sýkora, D. Chiral separation of novel diazenes on a polysaccharide-based stationary phase in the reversed-phase mode. J. Sep. Sci. 2017, 40, 1465–1469. [Google Scholar] [CrossRef] [PubMed]
  20. Urbańska, M.; Morawiak, P.; Senderek, M. Investigation of the tilt angle and spontaneous polarisation of antiferroelectric liquid crystals with a chiral centre based on (S)-(+)-3-octanol. J. Mol. Liq. 2021, 328, 115378. [Google Scholar] [CrossRef]
  21. Urbańska, M.; Perkowski, P.; Morawiak, P.; Senderek, M. Antiferroelectric and ferroelectric mesophases created by (S) enantiomers with a short oligomethylene spacer and their usefulness in the formulation of orthoconic mixtures. J. Mol. Liq. 2020, 320, 114452. [Google Scholar] [CrossRef]
  22. Sage, I. Thermochromic liquid crystals. Liq. Cryst. 2011, 38, 1551–1561. [Google Scholar] [CrossRef]
  23. Chełstowska, A.; Czerwiński, M.; Tykarska, M.; Bennis, N. The influence of antiferroelectric compounds on helical pitch of orthoconic W-1000 mixture. Liq. Cryst. 2014, 41, 812–820. [Google Scholar] [CrossRef] [Green Version]
  24. Czerwiński, M.; Tykarska, M.; Dabrowski, R.; Chełstowska, A.; Żurowska, M.U.; Kowerdziej, R.; Jaroszewicz, L.R. The influence of structure and concentration of cyano-terminated and terphenyl dopants on helical pitch and helical twist sense in orthoconic antiferroelectric mixtures. Liq. Cryst. 2012, 39, 1498–1502. [Google Scholar] [CrossRef]
  25. Czerwinski, M.; Tykarska, M. Helix parameters in bi- and multicomponent mixtures composed of orthoconic antiferroelectric liquid crystals with three ring molecular core. Liq. Cryst. 2014, 41, 850–860. [Google Scholar] [CrossRef]
  26. Żurowska, M.; Dąbrowski, R.; Dziaduszek, J.; Garbat, K.; Filipowicz, M.; Tykarska, M.; Rejmer, W.; Czupryński, K.; Spadło, A.; Bennis, N.; et al. Influence of alkoxy spacer length and fluorosubstitution of benzene ring on mesogenic and spectral properties of high tilted antiferroelectric 4’-(S)-1-(methylheptyloxycarbonyl)biphenyl-4-yl-4-(2,2,3,3,4,4,4-heptafluorobutoxy)alkoxybenzoates. J. Mater. Chem. 2010, 21, 2144–2153. [Google Scholar] [CrossRef]
  27. Drzewiński, W.; Dąbrowski, R.; Czupryński, K. Orthoconic antiferroelectrics. Synthesis and mesomorphic properties of optically active (S)-(+)-4-(1-methylheptyloxycarbonyl)phenyl 4’-(fluoroalkanoyloxyalkoxy)biphenyl-4-carboxylates and 4’-(alkanoyloxyalkoxy)biphenyl-4-carboxylates. Pol. J. Chem. 2002, 76, 273–284. [Google Scholar] [CrossRef]
  28. Belyakov, V.A.; Vladimir, E.D.; Orlov, V.P. Optics of cholesteric liquid crystals. Sov. Phys. Uspekhi 1979, 22, 64–88. [Google Scholar] [CrossRef]
  29. Tykarska, M.; Czerwiński, M.; Miszkurka, J. Influence of temperature and terminal chain length on helical pitch in homologue seriesnH6Bi. Liq. Cryst. 2010, 37, 487–495. [Google Scholar] [CrossRef]
  30. Tykarska, M.; Czerwiński, M. The inversion phenomenon of the helical twist sense in antiferroelectric liquid crystal phase from electronic and vibrational circular dichroism. Liq. Cryst. 2016, 43, 462–472. [Google Scholar] [CrossRef]
  31. Raszewski, Z.; Kędzierski, J.; Perkowski, P.; Piecek, W.; Rutkowska, J.; Kłosowicz, S.; Zieliński, J. Refractive indices of the MHPB(H)PBC and MHPB(F)PBC antiferroelectric liquid crystals. Ferroelectrics 2002, 276, 289–300. [Google Scholar] [CrossRef]
  32. Kowiorski, K.; Kędzierski, J.; Raszewski, Z.; Kojdecki, M.A.; Chojnowska, O.; Garbat, K.; Miszczyk, E.; Piecek, W. Complementary interference method for determining optical parameters of liquid crystals. Phase Transit. 2016, 89, 403–410. [Google Scholar] [CrossRef]
  33. Milewska, K.; Drzewiński, W.; Czerwiński, M.; Dąbrowski, R.; Piecek, W. Highly tilted liquid crystalline materials possessing a direct phase transition from antiferroelectric to isotropic phase. Mater. Chem. Phys. 2016, 171, 33–38. [Google Scholar] [CrossRef]
  34. Czerwiński, M.; Urbańska, M.; Bennis, N.; Rudquist, P. Influence of the type of phase sequence and polymer-stabilization on the physicochemical and electro-optical properties of novel high-tilt antiferroelectric liquid crystalline materials. J. Mol. Liq. 2019, 288, 111057. [Google Scholar] [CrossRef]
  35. Czerwiński, M.; de Blas, M.G.; Bennis, N.; Herman, J.; Dmochowska, E.; Otón, J.M. Polymer stabilized highly tilted antifer-roelectric liquid crystals—The influence of monomer structure and phase sequence of base mixtures. J. Mol. Liq. 2020, 327, 114869. [Google Scholar] [CrossRef]
  36. Chankvetadze, B. Recent trends in preparation, investigation and application of polysaccharide-based chiral stationary phases for separation of enantiomers in high-performance liquid chromatography. TrAC Trends Anal. Chem. 2019, 122, 115709. [Google Scholar] [CrossRef]
  37. Chen, X.; Yamamoto, C.; Okamoto, Y. Polysaccharide derivatives as useful chiral stationary phases in high-performance liquid chromatography. Pure Appl. Chem. 2007, 79, 1561–1573. [Google Scholar] [CrossRef] [Green Version]
  38. Lämmerhofer, M. Chiral recognition by enantioselective liquid chromatography: Mechanisms and modern chiral stationary phases. J. Chromatogr. A 2010, 1217, 814–856. [Google Scholar] [CrossRef] [PubMed]
  39. Scriba, G.K.E. Chiral recognition in separation science—An update. J. Chromatogr. A 2016, 1467, 56–78. [Google Scholar] [CrossRef]
  40. Ward, T.J.; Ward, K.D. Chiral separations: A review of current topics and trends. Anal. Chem. 2011, 84, 626–635. [Google Scholar] [CrossRef]
Figure 1. Example of D- and L-enantiomers.
Figure 1. Example of D- and L-enantiomers.
Crystals 12 01710 g001
Figure 2. (a) The general formula of the synthesized racemic mixtures. (b) Scheme of the synthesis of the new racemic mixtures.
Figure 2. (a) The general formula of the synthesized racemic mixtures. (b) Scheme of the synthesis of the new racemic mixtures.
Crystals 12 01710 g002
Figure 3. The temperature ranges of the phase transitions (from DSC measurements) for the racemic mixtures observed in the heating cycle.
Figure 3. The temperature ranges of the phase transitions (from DSC measurements) for the racemic mixtures observed in the heating cycle.
Crystals 12 01710 g003
Figure 4. The textures of the smectic phases obtained in the cooling cycle for the racemic mixture 7.(HH) (R,S). (a) The SmA phase at 140.5 °C; (b) The SmC phase at 130.7 °C; (c) The SmCA phase at 98.2 °C.
Figure 4. The textures of the smectic phases obtained in the cooling cycle for the racemic mixture 7.(HH) (R,S). (a) The SmA phase at 140.5 °C; (b) The SmC phase at 130.7 °C; (c) The SmCA phase at 98.2 °C.
Crystals 12 01710 g004
Figure 5. Comparing the temperature ranges of the phase transitions from DSC measurements for the base mixtures and the doped mixtures. (“*” means that the phase is observed).
Figure 5. Comparing the temperature ranges of the phase transitions from DSC measurements for the base mixtures and the doped mixtures. (“*” means that the phase is observed).
Crystals 12 01710 g005
Figure 6. (a) The temperature dependence of the helical pitch for mixtures W-458, W-458A and W-458B. (b) The temperature dependence of the helical pitch for mixtures W-459, W-459A and W-459B. (c) The temperature dependence of the helical pitch for mixtures W-460, W-460A and W-460B. (“*” means that the phase is observed).
Figure 6. (a) The temperature dependence of the helical pitch for mixtures W-458, W-458A and W-458B. (b) The temperature dependence of the helical pitch for mixtures W-459, W-459A and W-459B. (c) The temperature dependence of the helical pitch for mixtures W-460, W-460A and W-460B. (“*” means that the phase is observed).
Crystals 12 01710 g006aCrystals 12 01710 g006b
Table 1. The purity of the synthesized racemic mixtures.
Table 1. The purity of the synthesized racemic mixtures.
The Acronym of the Racemic MixturePurity [%]
2.(HH) (R,S)99.0
2.(HF) (R,S)99.0
2.(FH) (R,S)99.7
3.(HF) (R,S)99.5
3.(FF) (R,S)99.5
4.(HH) (R,S)99.9
4.(HF) (R,S)99.0
5.(HH) (R,S)99.8
5.(FH) (R,S)99.8
5.(FF) (R,S)99.8
6.(FH) (R,S)99.3
6.(FF) (R,S)99.7
7.(HH) (R,S)99.2
Table 2. The phase transition temperatures [°C] and enthalpies [J·g−1] of the synthesized racemic mixtures. (“*” means that the phase is observed and “-” means that it is not observed; The enthalpy is indicated by the italics).
Table 2. The phase transition temperatures [°C] and enthalpies [J·g−1] of the synthesized racemic mixtures. (“*” means that the phase is observed and “-” means that it is not observed; The enthalpy is indicated by the italics).
AcronymCr SmCA SmC SmA Iso
74.3 138.6
2.(HH) (R,S)*4.9*140.3--*
34.9 9.9
54.5 119.8
2.(HF) (R,S)*-*118.7--*
30.1 9.1
76.3 127.7 130.6
2.(FH) (R,S)*-*126.8*129.6-*
35.5 2.0 6.4
48.9 104.8
3.(HF) (R,S)*-*103.3--*
22.2 8.2
56.8 111.2 113.9 115.1
3.(FF) (R,S)*30.3*104.7*113.0*114.2*
23.9 0.07 1.15 5.5
52.3; 56.7 144.4 148.4
4.(HH) (R,S)*-*143.7-*147.4*
4.5; 20.2 1.7 6.8
49.6; 60.2 122.5
4.(HF) (R,S)*-*122.6--*
25.9; 3.2 6.2
60.4 136.5 143.1
5.(HH) (R,S)*-*135.9-*142.2*
35.6 1.1 6.9
69.8 108.1 119.6 129.2
5.(FH) (R,S)*-*95.6*118.8*127.8*
33.6 0.04 1.1 6.3
72.6 110.9 119.8 126.9
5.(FF) (R,S)*14.3*101.6*118.9*125.7*
25.2 0.03 0.9 5.6
59.8 120.8 131.5
6.(FH) (R,S)*-*120.3-*130.5*
25.9 0.75 6.5
68.4 121.3 129.1
6.(FF) (R,S)*40.4*120.4-*127.6*
26.9 0.76 5.9
36.0 114.3 131.2 140.1
7.(HH) (R,S)*-*105.5*130.3*139.5*
13.25 0.03 0.8 6.8
First row—temperatures from DSC measurements obtained in the heating cycle; second row—temperatures from DSC measurements obtained in the cooling cycle; third row—transition enthalpies.
Table 3. The compositions of the six prepared mixtures.
Table 3. The compositions of the six prepared mixtures.
Acronyms of the Doped MixturesBase MixturesAcronyms of the Dopants
W-458AW-4582.(FH) (R,S)
W-458BW-4583.(HF) (R,S)
W-459AW-4595.(FF) (R,S)
W-459BW-4597.(HH) (R,S)
W-460AW-4604.(HF) (R,S)
W-460BW-4606.(FH) (R,S)
Table 4. The mesomorphic and thermodynamic properties of the prepared mixtures. (“*” means that the phase is observed and “-” means that it is not observed; The enthalpy is indicated by the italics).
Table 4. The mesomorphic and thermodynamic properties of the prepared mixtures. (“*” means that the phase is observed and “-” means that it is not observed; The enthalpy is indicated by the italics).
MixturesCr SmCA* SmC* SmA* Iso
70.9–73.6 95.0–95.6 100.5–101.7
48.2–49.6 94.5–94.9 99.8–101.3
W-458A*-*71.0*93.8*99.4*
58.5 94.1 99.9
0.08 1.98 4.3
74.8–76.0 92.8–93.2 97.0–97.7
57.2–57.8 92.5–92.8 96.4–97.1
W-458B*-*75.0*91.8*96.2*
63.8 92.0 96.3
0.15 2.15 4.4
70.5–71.7 85.9–90.4
55.4–56.3 84.5–87.6
W-459A*-*72.2*85.1-*
60.5 86.5
0.08 7.5
72.5–73.6 86.4–92.4
61.7–62.5 84.8–89.8
W-459B*-*73.1*84.9-*
64.9 88.2
0.75 6.1
78.5–79.2 86.3–91.5
71.2–72.0 83.8–88.4
W-460A*-*78.0*84.2-*
72.0 87.2
0.17 6.4
72.0–73.1 84.0–84.7 88.7–93.2
63.1–61.9 83.2–84.0 87.3–90.6
W-460B*-*71.3*82.3*87.2*
63.8 83.4 89.6
0.07 1.63 4.1
First row—temperatures from POM measurements obtained in the heating cycle; Second row—temperatures from POM measurements obtained in the cooling cycle; Third row—temperatures from DSC measurements obtained in the heating cycle; Fourth row—temperatures from DSC measurements obtained in the cooling cycle; Fifth row—transition enthalpies [J·g−1].
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Urbańska, M.; Szala, M. Synthesis, Mesomorphic Properties and Application of (R,S)-1-Methylpentyl 4′-Hydroxybiphenyl-4-carboxylate Derivatives. Crystals 2022, 12, 1710. https://doi.org/10.3390/cryst12121710

AMA Style

Urbańska M, Szala M. Synthesis, Mesomorphic Properties and Application of (R,S)-1-Methylpentyl 4′-Hydroxybiphenyl-4-carboxylate Derivatives. Crystals. 2022; 12(12):1710. https://doi.org/10.3390/cryst12121710

Chicago/Turabian Style

Urbańska, Magdalena, and Mateusz Szala. 2022. "Synthesis, Mesomorphic Properties and Application of (R,S)-1-Methylpentyl 4′-Hydroxybiphenyl-4-carboxylate Derivatives" Crystals 12, no. 12: 1710. https://doi.org/10.3390/cryst12121710

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop