Next Article in Journal
Sustainable Methodology for Operational and Formal Digital Skills Acquisition: A Case Study of e-Health Inclusion
Previous Article in Journal
Insights of Digital Transformation Processes in Industrial Symbiosis from the Viable Systems Approach (vSa)
Previous Article in Special Issue
Sustainable Biological Ammonia Production towards a Carbon-Free Society
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Fermentative Production of Lasiodiplodan by Lasiodiplodia theobromae CCT3966 from Pretreated Sugarcane Straw

by
Peyman Abdeshahian
1,*,
Jesús Jiménez Ascencio
1,
Rafael R. Philippini
1,
Felipe Antonio Fernandes Antunes
1,
Avinash P. Ingle
2,
Mojgan Abdeshahian
3,
Júlio César dos Santos
1 and
Silvio Silvério da Silva
1
1
Department of Biotechnology, Engineering School of Lorena, University of São Paulo, São Paulo 12602-810, Brazil
2
Biotechnology Centre, Department of Agricultural Botany, Panjabrao Deshmukh Krishi Vidyapeeth, Akola 444104, India
3
Department of Agriculture Science, Payame Noor University (PNU), Tehran 19395-4697, Iran
*
Author to whom correspondence should be addressed.
Sustainability 2021, 13(17), 9697; https://doi.org/10.3390/su13179697
Submission received: 22 June 2021 / Revised: 23 August 2021 / Accepted: 23 August 2021 / Published: 29 August 2021
(This article belongs to the Special Issue Sustainable Fermentation Technology)

Abstract

:
Lasiodiplodan is a β-glucan polymer with different interesting characteristics, including therapeutic properties. It is an extracellular product, which is produced by the filamentous fungus Lasiodiplodia theobromae, using glucose as a substrate. In the present work, the production of lasiodiplodan was studied by the utilization of sugarcane straw as a low-cost carbon source. Glucose-rich sugarcane straw hydrolysate was obtained by a sequential pretreatment with dilute nitric acid (1% v/v) and sodium hydroxide (1% w/v), followed by enzymatic hydrolysis. The fermentation process was conducted by the cultivation of the strain Lasiodiplodia theobromae CCT3966 in sugarcane straw hydrolysate in a shake flask at 28 °C for 114 h. It was found that hydrolysate obtained after enzymatic hydrolysis contained 47.10 gL−1 of glucose. Fermentation experiments of lasiodiplodan synthesis showed that the peak yield and productivity of 0.054 gg−1 glucose consumed and 0.016 gL−1 h−1, respectively, were obtained at 72 h fermentation time. Fungal growth, glucose consumption, and lasiodiplodan production from sugarcane straw hydrolysate presented a similar pattern to kinetic models. The study on the chemical structure of lasiodiplodan produced showed it had a β-glucan construction. The current study revealed that sugarcane straw is a promising substrate for the production of lasiodiplodan.

1. Introduction

β-glucans are polysaccharide-based polymers, which have promising applications in medicine and pharmaceutical sectors because they have been found to possess potential antimicrobial and anticancer properties. In addition, these polymers play a crucial role in the improvement of the human immune system and decrease of blood cholesterol and also helps in wound healing. Moreover, β-glucans can be effectively used in the cosmetics and food industry as fat substitutes, emulsifiers, and food fibers [1,2,3]. Many microorganisms such as fungi and bacteria were reported to have the ability of β-glucan synthesis using carbon sources. Among them, the filamentous fungus Lasiodiplodia theobromae has received a growing interest by researchers for the biosynthesis of an extracellular β-glucan polymer, namely lasiodiplodan, since this fungus has a high potential for industrial production level [1,4]. In this regard, the tremendous biological characteristics of lasiodiplodan such as anti-proliferative effect on breast cancer cells, hypoglycemic function, and antioxidant activities have made it an attractive biopolymer for commercial applications [5,6]. Generally, the production costs of the fermentative products highly depend on the fermentation substrates, mainly carbon source, as the use of raw materials such as lignocellulosic biomass and agro-industrial residues decrease the manufacturing costs [7].
Current efforts for microbial synthesis of lasiodiplodan are based on the utilization of commercial sugars, particularly glucose [4,5,8,9,10]. These sugars are mostly obtained from unsustainable carbon sources such as food-derived carbohydrates, which strongly compete with food chains [11,12]. Furthermore, the production process will be costly where large-scale synthesis of glucan is targeted. Hence, production of lasiodiplodan from commercial sugars is not cost-efficient. In order to attain process economics and successful industrialization of lasiodiplodan production, the exploitation of abundant, renewable, and low-cost natural bioresources enhances economically feasible production of lasiodiplodan [13]. Considering these facts, there is a rising trend in the utilization of waste carbon sources for the production of biochemicals. Lignocellulosic feedstocks are the most versatile and viable carbon sources, which could provide fermentable sugars for the biological synthesis of chemicals. Moreover, these raw materials are promising carbon sources and economically competitive ones as compared with food-based carbon sources [14,15]. However, current knowledge about lasiodiplodan synthesis from lignocellulosic biomass is rudimentary and very limited research has been performed in this regard [13,16].
Sugarcane is known as one of the most abundant industrial crops in Brazil. Harvesting sugarcane leads to the generation of a lignocellulosic residue, namely sugarcane straw (tops and dry leaves of sugarcane plant) with an amount of 10–30 mega gram per hectare (Mg ha−1), which is left on the land after harvesting [17,18]. In this regard, 14% dry weight of the sugarcane plant forms sugarcane straw in sugarcane processing chains [19]. Considering the large production of sugarcane in Brazil (642.72 million metric tons of sugarcane in Brazil’s marketing year for the duration March 2019–April 2020), a high quantity of sugarcane straw is produced [20]. A part of sugarcane straw is left on the ground to make soil fertile [21]. The rest of the sugarcane straw can be utilized as an energy source or as a lignocellulosic feedstock for the production of biochemicals and value-added products [22]. The lignocellulosic structure of sugarcane straw is composed of a high content of cellulose ranging from 37% to 44.5% [23,24]. The high amount of cellulose in sugarcane straw represents a potential and low-cost carbon source to obtain fermentable sugars, which could further be utilized for the production of biochemicals such as lasiodiplodan.
In order to access cellulosic fraction for effective hydrolysis by cellulolytic enzymes, a pretreatment step is often imperative to partly break the recalcitrant structure of the lignocellulose and to allow the removal of hemicellulose and lignin constituents, which in turn leads to the enhancement of cellulose hydrolysis [25,26,27,28,29,30]. In this context, several pretreatment methods have already been applied to fractionate the lignocellulosic components of biomass [31]. Among them, dilute acid treatment has potential for the dissociation of hemicellulose component, which could be utilized efficiently in industrial sectors. Acid pretreatment followed by alkaline pretreatment for delignification of biomass has commonly been used to obtain a high amount of cellulose content [25,32,33,34]. Different acids such as sulfuric (H2SO4), hydrochloric (HCl), nitric acid (HNO3), and phosphoric acid (H3PO4) have been used for the pretreatment of lignocellulosic biomass [33]. Among these, HNO3 was reported to have the less corrosive effect on equipment, and has been faster and more effective for fractionating lignocellulose structure [35].
The study fulfilled by Abdeshahian et al. [36] showed that an untreated sample of sugarcane straw was composed of 41.25% cellulose, 35.17% hemicellulose, 17.25% lignin, and 2.81% ash. This indicates that sugarcane straw could be regarded as low-cost lignocellulosic biomass to obtain glucose, which can be further used for the production of glucan biopolymer through microbial fermentation process.
Therefore, the aim of this study was to investigate the feasibility of lasiodiplodan production from the sugarcane straw, which was subjected to a sequential pretreatment by diluted nitric acid (HNO3 1% v/v) and NaOH (1% w/v). In this study, the fungal strain L. theobromae CCT3966 was cultivated on the glucose obtained from enzymatic saccharification of pretreated sugarcane straw to synthesize lasiodiplodan. Moreover, a kinetic model for the production of lasiodiplodan by the fungal strain in the fermentation medium was studied. The chemical structure of lasiodiplodan produced was studied using Fourier Transform Infrared Spectroscopy (FT-IR) and X-ray diffractometry.

2. Materials and Methods

2.1. Raw Material

Sugarcane straw was obtained from Ipiranga Agroindustrial in Descalvado, São Paulo, Brazil. Sugarcane straw collected with moisture content of less than 10% was then milled using a laboratory knife mill unit. The milled sugarcane straw was transferred in a plastic bag and stored at the temperature of 4 °C prior to its use for experiments.

2.2. Microorganism

The filamentous fungal strain Lasiodiplodia theobromae CCT3966 was procured from Fundação André Tosello Pesquisa e Tecnologia (Campinas, São Paulo, Brazil). The isolate was maintained on the yeast malt agar (Sigma-Aldrich, São Paulo, Brazil) with the chemical composition of (gL−1): dextrose, 10; yeast extract, 3; malt extract, 3; peptone, 5, and agar, 20, with a pH value of 6.2 at 30 °C. The fungal inoculum was prepared by the cultivation of the strain on yeast malt agar slant in 500 mL flasks at 30 °C. After growing fungal cells, a defined volume of sterile distilled water containing 0.1% Tween 80 was added to the flask, and mixed well. A fungal suspension was prepared for inoculation of the production culture.

2.3. Pretreatment of Sugarcane Straw

Initially, the raw sugarcane straw was subjected to the pretreatment by the acid solution to remove hemicellulose fraction. For acid pretreatment, dilute nitric acid (HNO3 1% v/v) (Labsynth®, São Paulo, Brazil) was used with a solid to liquid ratio of 1:10. In this way, 20 g raw sugarcane straw was placed in 500 mL Erlenmeyer flask and 200 mL of dilute HNO3 was added, followed by vigorous mixing. The flask was then transferred into an autoclave and heated at 121 °C for 60 min [37]. The solid part was then collected, washed with water (pH 7) and dried until the moisture content reached less than 10%.
To remove the lignin fraction from biomass, the acid pretreated sugarcane straw was subjected to alkaline pretreatment. It was conducted by mixing cellulignin portion with a NaOH (1% w/v) (Labsynth®, São Paulo, Brazil) solution in a solid to liquid ratio of 1:10. For this, 200 mL NaOH solution was transferred to a 500 mL Erlenmeyer flask containing 20 g of acid pretreated sugarcane straw and mixed well. The mixture was heated at 121 °C for 60 min using an autoclave [38]. Later, the solid fraction was separated from the liquid part. The solid part was washed with water to remove lignin adhered to biomass and neutralize delignified sugarcane straw. The pretreated sugarcane straw was dried until the moisture content reached less than 10%.

2.4. Enzymatic Hydrolysis

Delignified sugarcane straw was subjected to enzymatic saccharification for conversion of cellulose fraction to glucose. The enzymatic hydrolysis of the pretreated sugarcane straw was performed using a commercial enzyme preparation, namely Cellic® CTec2 (Sigma-Aldrich, Brazil Ltd., São Paulo, Brazil) in 125 mL Erlenmeyer flasks. The hydrolysis assay was conducted at a solid loading of 7.5% (w/v) using 50 mM sodium citrate buffer (pH 5.0) in a total volume of 40 mL, so that the enzyme loading of 15 FPU (filter paper units) per gram of dry biomass was applied for 72 h at 50 °C. The mixture was then centrifuged at 2860× g for 10 min. The obtained hydrolysate was stored at −18 °C. The amount of glucose in hydrolysate was measured and the cellulose to glucose conversion (XC-G) was calculated using Equation (1):
X C - G =   C G   C B × f × 1.11 × 100
where XC-G shows the glucose conversion value (%), CG (gL−1) denotes the concentration of glucose released at the time of sampling, CB (gL−1) represents the concentration of delignified sugarcane straw used in the flask before the beginning of enzymatic hydrolysis, f indicates the content of cellulose in the dry delignified sugarcane straw, and 1.11 denotes cellulose to glucose conversion coefficient [39].

2.5. Production of Lasiodiplodan

Lasiodiplodan production was conducted in a 125 mL-Erlenmeyer flask containing sugarcane straw hydrolysate in which glucose concentration was set to 40 gL−1 with an addition of 2 gL−1 KH2PO4, 2 gL−1 MgSO4.7H2O, and 1 gL−1 yeast extract. The initial pH value of the hydrolysate was adjusted to 7.0. Then, the mixture was sterilized at 121 °C for 20 min. Later, fungal inoculum (7 mL) was inoculated in sterile and cooled medium, followed by incubation on a rotary shaker at 200 rpm and temperature of 28 °C for 114 h.

2.6. Kinetic Models of Lasiodiplodan Production Using Sugarcan Straw Hydrolysate

The production of lasiodiplodan by L. theobromae CCT3966 from sugarcane straw hydrolysate was evaluated by conducting a kinetic study on the production process. In this view, the growth of the fungal strain was described by the logistic (autonomous) model as presented previously by Zhang et al [40]. The logistic model for the growth of microbial growth was defined:
d X d t = μ X   ( 1   X X m a x )
where μ represents the maximum specific growth rate (h−1), X is fungal biomass (gL−1), and X m a x is the highest fungal biomass concentration (gL−1), which was measured at the end of fermentation. The integration of Equation (2) can give the following Equation:
X t =   X o e μ t 1.0   X o   X m a x 1.0 e μ t
where X t is the biomass concentration (gL−1) at time t and X o indicates the initial biomass concentration (gL−1) at t = 0 when microbial inoculation was carried out. Equation (4) can be derived from Equation (3) as:
μ t = ln [ X t   X m a x 1.0 X t   X m a x ln X m a x X o 1.0 ]
where the symbol of ln denotes the natural logarithm. The value of μ was calculated by plotting ln [ X t   X m a x 1.0 X t   X m a x ]   against fermentation time ( t ) so that it provided a linear graph with a slope of μ (h−1).
The Leudeking–Piret kinetic [41] was utilized to describe lasiodiplodan production as shown in Equation (5):
d P d t = m d X d t + n X
Equation (5) includes a growth-associated term m ( d x / d t ) and a non-growth associated term n X . In consideration of the fact that production of lasiodiplodan by L. theobromae CCT3966 is a growth-associated process, the term nX was, therefore, not included for calculations. The integration of Equation (5) forms:
P t = P o + m   X o e μ t 1.0   X o X m a x 1.0 e μ t 1.0
where P t   is lasiodiplodan produced at time t and P t is the lasiodiplodan concentration (gL−1) at t = 0. Plotting P t P o against   X o e μ t 1.0   X o X m a x 1.0 e μ t 1.0 generates a linear curve in which the slop is equal to the value of m.
The consumption of glucose as a microbial substrate was studied using the kinetic model presented by Zhang et al. [40] as:
S t = S o α   ( X t X o ) β   X m a x μ l n 1.0   X o   X m a x 1.0 e μ t
where S t is the substrate (glucose) concentration (gL−1) at time t and the term So is the initial substrate concentration (gL−1) in culture medium at t = 0. Factors α and β denote coefficients. The value of kinetic parameter α was obtained by plotting S o S t β   X m a x μ l n 1.0   X o   X m a x 1.0 e μ t against   ( X t X o ) .   Therefore, the slope of the linear curve generated denotes value of α . The factor β was computed by Equation (8):
β = d S / d t   X t
The statistical evaluation of the proposed models in relation to experimental data was carried out by the mean squared error (MSE) and coefficient of determination (R2) [40]:
MSE = 1 n   i = 1 n   ( y i f i ) 2
R 2 = 1 ( y i f i ) 2 ( y i y ¯ i ) 2
where y i ,   y ¯ i , f i ,   and n represent experimental data, mean of experimental data, the model data, and the number of samples taken for experimental data, respectively. The yield of lasiodiplodan ( Y p / s ) was calculated as the ratio of lasiodiplodan produced to the glucose consumed (gg−1). The volumetric productivity of lasiodiplodan ( Q p ) was measured as the ratio of amount of lasiodiplodan produced to the time of the fermentaion (gL−1 h−1). The ratio of the amount of biomass produced to glucose consumed (gg−1) was defined as Y x / s [1].

2.7. Measurement of Biomass and Lasiodiplodan

At the end of the lasiodiplodan production process, the culture broth was collected. Fungal biomass was separated by centrifugation at 2860× g for 10 min. The precipitated biomass was washed properly and dried in an oven at 60 °C to achieve constant weight. For lasiodiplodan measurement, the supernatant of the culture broth was recovered and the dissolved lasiodiplodan was precipitated by adding 70% ethanol into fermentation medium with the ratio of 1:3 (1 part mixture and 3 part 70% ethanol) and the mixture was kept at 4 °C (overnight). The precipitate was then separated from the supernatant and dried at the temperature of 60 °C to achieve constant weight. The mass of lasiodiplodan was then weighed using a laboratory balance [1,16].

2.8. Chemical Characterization of Pretreated Sugarcane Straw

The chemical content of cellulose, hemicelluloses, and lignin for acid pretreated and alkaline pretreated sugarcane straw was determined using the method presented by National Renewable Energy Laboratory (NREL) [42]. The ash content of sugarcane straw was measured using a muffle furnace at 500 °C for 24 h.

2.9. Scanning Electron Microscopy (SEM) of Pretreated Biomass

In order to study morphological changes in the lignocellulose structure of sugarcane straw after pretreatment, the pretreated biomass was analyzed by SEM (Hitachi TM3000, Chiyoda, TYQ, Japan). For this, dilute acid pretreated sugarcane straw and alkaline pretreated sugarcane straw (cellulose pulp) were subjected to SEM for morphological analysis at 1000× magnification [16].

2.10. Fourier Transform Infrared (FTIR) Spectroscopy and X-ray Diffraction Analysis (XRD)

FTIR and XRD analysis of lasiodiplodan samples were performed to study the biochemical structure of lasiodiplodan produced [16]. FT-IR spectrum was recorded in the region of 4000–600 cm−1 using a Perkin Elmer® SpectrumTM GX (Shelton, CT, USA). XRD was conducted over a diffraction angle (2θ) of 10–60. X-ray diffractogram was attained by PANalytical (Malvern Panalytical, UK) [13].

2.11. Measurement of Glucose in Hydrolysate

The concentration of sugars was analyzed by High-Performance Liquid Chromatography (HPLC) in a Agilent 1200 series (Agilent Technologies Inc., USA) equipment with a Refractive index detector RID-6A and a HPX-87H (300 × 7.8 mm) column (Bio-Rad, USA). The analysis conditions were: column temperature of 45 °C, the solution of 0.01 N H2SO4 as the mobile phase, flow rate of 0.6 mL/min, and 20 μL injection volume [13].

2.12. Statistical Analysis

Experimental data were statistically analyzed by ordinary one-way ANOVA method and two-way ANOVA followed by Dunnett’s multiple comparisons test at 95% confidence level (p < 0.05) using GraphPad Prism 8.0.2 software. The values of kinetic parameters of the models generated were calculated manually.

3. Results

3.1. Chemical Composition of Pretreated Sugarcane Straw

As discussed earlier, the pretreated sugarcane straw was analyzed for the amount of different components. After nitric acid pretreatment of the raw sugarcane straw, the chemical composition of pretreated sugarcane straw was analyzed. The lignocellulosic contents of acid pretreated sugarcane straw are presented in Table 1. The chemical composition profile of sugarcane straw pretreated with dilute nitric acid revealed that the hemicellulosic content in untreated sugarcane straw reached 3.53% after acid pretreatment.
On the other hand, the amount of cellulose and lignin components of sugarcane straw after acid pretreatment reached 62.28% and 32.15%, respectively (Table 1). It is noteworthy that the acid pretreatment of the lignocellulosic structure of plants causes a considerable hydrolysis of hemicellulosic content. However, cellulose is hydrolyzed by acid to a lesser extent.
As can be observed in Table 1, the sugarcane straw obtained after alkaline pretreatment was composed of 82.22% cellulose, indicating that cellulose content notably increased compared to the cellulose content recorded after acid pretreatment of sugarcane straw (62.28%).
In addition, it was also recorded that the hemicellulose fraction decreased even more and was not detected after alkaline hydrolysis of acid pretreated sugarcane straw. Moreover, the lignin content of alkaline pretreated sugarcane straw decreased to 16.28%, indicating the success of alkaline pretreatment in lignin removal (49.36%) after alkaline pretreatment (Table 1). The statistical analysis of the pretreatment experiments showed that cellulose content of sugarcane straw was significantly enhanced after acid pretreatment compared to raw sugarcane straw (p < 0.01) as well as after alkaline pretreatment in comparison to that for raw sugarcane straw and acid pretreated biomass (p < 0.01). On the other hand, the hemicellulose content of untreated sugarcane straw significantly decreased in both acid pretreated and alkaline pretreated biomass (p < 0.01). Although the lignin content of sugarcane straw significantly decreased after alkaline pretreatment compared to that in acid pretreated biomass (p < 0.01), variation in the lignin content of sugarcane straw was not significant after alkaline pretreatment compared to that in untreated biomass (p > 0.05).

3.2. Pretreatment Effect on Structural Modification of Sugarcane Straw

SEM of the pretreated sugarcane straw was carried out to study the structural modification after acid and alkaline pretreatment. Figure 1 depicts SEM images of pretreated sugarcane straw. As shown in Figure 1A, acid pretreated sugarcane straw revealed disordered fibrous organization with rupture in vascular cells. The changes in morphology of xylem structure are displayed as broken vessel elements and tracheids with the thin and dissociated cell wall. Figure 1B depicts the micrograph of sugarcane straw pretreated by alkaline after acid pretreatment. It can be observed that deep fracture in the fibrous organization with perpendicular breaks in the fiber cells occurred, indicating the increase in the accessibility of the enzymes to the structure of delignified sugarcane straw for hydrolysis of cellulose fraction.

3.3. Enzymatic Hydrolysis of Raw and Pretreated Sugarcane Straw

Delignified sugarcane straw obtained after alkaline pretreatment was hydrolyzed by the cellulase preparation. The results of enzymatic saccharification of the pretreated sugarcane straw revealed that the concentration of glucose released at 6, 12, 24, 48, and 72 h were 3.25, 21.16, 42.06, 44.21, and 47.10 gL−1, respectively (Figure 2A). The results indicated that a high amount of glucose was released at 24 h of enzymatic saccharification, while the rise in glucose released from 24 to 72 h was comparatively not considerable.
Statistical analysis of the glucose produced in enzymatic hydrolysis of delignified sugarcane straw (Figure 2) corroborated that the concentration of glucose was significantly enhanced (p < 0.01) during the initial 24 h of hydrolysis time. The comparison of glucose released after 24 h of enzymatic saccharification indicated that the increase in glucose concentration was insignificant (p > 0.05) between 24 to 72 h of enzymatic hydrolysis.
In this regard, glucose released could have an inhibitory effect on the cellulase so that increasing glucose concentration during cellulose hydrolysis dwindled enzymatic saccharification. Furthermore, the more accessible cellulose fraction can be hydrolyzed in the first hours of hydrolysis, remaining a more recalcitrant biopolymer in later times. This fact is also shown by the cellulose to glucose conversion yield (Figure 2B).
As can be found from Figure 2B, the conversion percentage of cellulose to glucose for enzymatic hydrolysis at 6, 12, 24, 48, and 72 h was 4.63, 30.87, 59.98, 63.05, and 67.15%, respectively, indicating an increasing trend in the conversion of cellulose to glucose with period of hydrolysis. It is noteworthy that a high yield of glucose conversion was obtained in the first 24 h enzymatic hydrolysis. This result showed that glucose conversion reached about 70% in 72 h of hydrolysis, but about 60% of conversion yield was achieved in the first 24 h.

3.4. Lasiodiplodan Production Using Sugarcane Straw Hydrolysate

Figure 3A depicts the time course for the growth of L. theobromae CCT3966 in sugarcane straw hydrolysate. As shown, the lag phase was not long. The initial fungal biomass ( X o = 0.13 gL−1) started to grow shortly after the inoculation ( t = 0). The fungal cells grew drastically during 96 h of fermentation indicating the exponential phase of the growth. The maximum specific growth rate (μ) was obtained at exponential growth phase with the value of 0.06 h−1. Similarly, the decrease in biomass growth was recorded after 96 h of fermentation, with a stationary phase of the biomass growth from 96 h to 114 h of fermentation. The highest biomass formed ( X m a x ) was 3.01 gL−1. The growth of the isolate L. theobromae CCT3966 in the sugarcane straw hydrolysate was studied by the logistic model. Here, the growth of fungal cells in sugarcane straw hydrolysate followed the growth pattern generated by the model. This indicated that the kinetic model could predict well the growth of the biomass in experimental conditions. The values of the kinetic parameters of the model are shown in Table 2.
The production of lasiodiplodan by L. theobromae CCT3966 is shown in Figure 3B. It shows that the gradual production of lasiodiplodan by the fungal cells was carried out during initial 24 h of fermentation. However, the production of lasiodiplodan exhibited an increasing trend from 24 to 72 h of the fermentation. The highest lasiodiplodan yield ( Y p / x ) and productivity ( Q p ) of 0.054 gg−1 glucose consumed and 0.016 gL−1h−1 were recorded, respectively, at 72 h of fermentation.
Moreover, it was also observed that the further increase in the fermentation time from 72 to 114 h had no positive effect on the production of lasiodiplodan. The reduction in lasiodiplodan production after 72 h was possibly due to the depletion of nutrients (glucose and yeast extract) and dissolved oxygen in the culture medium since these are the decisive factors for fungal growth and lasiodiplodan synthesis. Figure 3A,B clearly indicated that the production of lasiodiplodan by the strain L. theobromae CCT3966 was a growth-associated process since the maximum lasiodiplodan production was obtained in the exponential growth phase.
Figure 3B also depicts the pattern of lasiodiplodan production presented by the kinetic model generated. As shown, the biosynthesis of lasiodiplodan by the strain L. theobromae CCT3966 in experimental fermentation was satisfactorily correlated with lasiodiplodan production presented by the kinetic model.
Figure 3C depicts the profile of the glucose consumption in the production of lasiodiplodan by the isolate L. theobromae CCT3966. It was observed that fugal cells utilized glucose continuously from the early fermentation course to end. The fungal biomass consumed most of the initial amount of glucose until 72 h of fermentation time (21.01 gL−1) when the highest production of lasiodiplodan occurred (Figure 3A). As fermentation proceeded, a low quantity of glucose (13.32 gL−1) was utilized by the fungal cells during 72 h to 114 h of the fermentation time. The lower glucose consumption after 72 h was in line with the reduction of lasiodiplodan production during this fermentation course.
It can also be found from Figure 3C that the glucose presented in the sugarcane straw hydrolysate was not completely consumed as a residual glucose concentration of 5.67 gL−1 was measured at the end of fermentation course. Considering the amount of glucose consumed, the yield of fungal biomass ( Y x / s ) was 0.09 gg−1. As shown in Figure 3C, the glucose consumption by the fungal cells in experimental fermentation was in a favorable agreement with that in the kinetic model.
The statistical analysis of the generated models using R2 and MSE revealed that simulated models with R2 value 0.9 and MSE value less than 10% were in good agreement with the experimental results. Moreover, it indicated that the models adequately represented the real process and they could be utilized to explain the process pattern of lasiodiplodan production by L. theobromae CCT3966 from sugarcane straw hydrolysate in batch fermentation.

3.5. Chemical Structure of the Lasiodiplodan Produced by L. theobromae CCT3966

The FTIR spectra of the lasiodiplodan produced by L. theobromae CCT3966 have been illustrated in Figure 4A. The fingerprint areas between 774–938 cm−1 pointed out the presence of bands of glycosidic linkages with the β-type structure, which can be found in several microbial glucans. Peaks and bands between 1000 and 1200 cm−1 indicate axial deformations on C-C, C-H and R-C-O-C-R (ether) linkages. The absorption peak shown in the 1072 cm−1 could indicate the symmetrical stretching vibrations of C = O bonds showing the characteristic of the pyranose ring present in the monomers of glucans. The bands at 1255 cm−1 of FTIR spectra revealed the C-O-C asymmetric stretching vibrations. The band observed in the region 1406 cm−1 could be attributed to the symmetric deformation of CH2 and COH groups. In this regard, the absorption peak at 1633 cm−1 shows the C=O bond, which represents the presence of the glucose ring. The absorption peak detected at the 2932 cm−1 is related to the C-H stretching of the CH2 group. The peak shown in 3411 cm−1 indicates the hydroxyl group (OH) stretching.
X-ray diffraction of lasiodiplodan produced by L. theobromae CCT3966 is illustrated in Figure 4B. As can be seen, the diffractogram pattern is shown by a broad peak at around 22° (2θ) indicating the polymeric structure of lasiodiplodan with a non-crystalline property.

4. Discussion

Nitric acid had a notable effect on hemicellulose removal, which could increase cellulose content. In this regard, the study fulfilled by Miléo et al. [32] revealed that the pretreatment of sugarcane straw using 1% sulfuric acid at 120 °C for 10 min resulted in the considerable removal of hemicellulosic fraction from sugarcane straw, from 29.7 to 8.5%. Moutta et al. [43] investigated the pretreatment of sugarcane straw by sulfuric acid 2.9% (w/v). It was observed that a high amount of hemicellulose composition was hydrolyzed, while cellulose fraction decisively increased.
On the other hand, acid pretreatment could bring about the generation of pseudo-lignin and the re-condensation of lignin, which leads to the increment of cellulose and lignin content after acid pretreatment compared to that in raw biomass [19,43,44]. After alkaline pretreatment of sugarcane straw, cellulose content increased up to 82.22%. This result is comparable with the results obtained by Candido et al. [25] who applied consecutive acid and alkaline pretreatment for sugarcane straw by sulfuric acid and sodium hydroxide, respectively. They found that the cellulose content of raw sugarcane straw with the value of 38.82% reached 60.80% and 84.56% after acid and subsequent alkaline pretreatment, respectively.
This phenomenon can be attributed to the point that alkaline pretreatment causes the removal of a high quantity of the lignin content, which could enlarge cellulose constitution owing to the swelling of cellulose fibers [19,45,46]. The study conducted by Miléo et al. [32] revealed when cellulignin sugarcane straw with hemicellulose and lignin composition of 8.5% and 38.2%, respectively, was pretreated by NaOH (1.5% w/v), hemicellulose and lignin content decreased to 6.4% and 26.8%, respectively. It was also observed that the cellulose composition of delignified sugarcane straw reached 57.8% in comparison to 46.3% cellulose content of cellulignin sugarcane straw.
After sequential pretreatment of the sugarcane straw using nitric acid and sodium hydroxide, the enzymatic saccharification of pretreated biomass resulted in a remarkable cellulose conversion into glucose (60%) with releasing 42.06 gL−1 glucose in the first 24 h of hydrolysis (Figure 2). In contrast, the results indicated that there was no significant difference (p < 0.0.1) in the glucose produced between 24 h to 72 h of enzymatic hydrolysis. This finding revealed the important effect of the hydrolysis time in enhancement of glucose release during 24 h so that the rise in glucose production and saccharification percentage was conducted to a lesser extent at 24 h to 72 h of hydrolysis reaction [47].
The results obtained for enzymatic saccharification of pretreated sugarcane straw are comparable with the previous studies. The study fulfilled by Santos-Rocha et al. [39] revealed that enzymatic saccharification of hydrothermally pretreated sugarcane straw by cellulase enzyme led to the release of 38 gL−1 glucose so that increasing enzymatic reaction time enhanced glucose concentration up to 48.9 gL−1. A similar observation was found by Moutta et al. [43], who hydrolyzed sugarcane straw that had been pretreated previously by sulphuric acid (2.9%, 30 min). Their study showed that after 24 h of enzymatic hydrolysis by cellulase, an amount of 19 gL−1 glucose was triggered, while continuous hydrolysis up to 72 h resulted in 21 gL−1 glucose. Pereira et al. [48] conducted pretreatment of sugarcane straw by dilute sulfuric acid (1.5%, 121 °C, 30 min), followed by enzymatic hydrolysis for 24 h using cellulase preparations. It was noted that a quantity of 31 gL−1 glucose was produced after 24 h. In an attempt, sugarcane straw was utilized for converting cellulose fraction to glucose by cellulose-degrading enzymes. It was found that enzymatic saccharification of alkaline pretreated sugarcane straw could hydrolyze cellulose to release glucose with an overall cellulose conversion of 67% [49].
In this study, production of lasiodiplodan occurred from the beginning of the fermentation time and continued to the highest lasiodiplodan production at 72 h fermentation, while it was followed by a reduced production of lasiodiplodan from 72 to 114 h showing a correlation between fermentation time and lasiodiplodan formation. This finding indicated that fermentation time is of high importance to attain the highest lasiodiplodan yield when the fungal cells are in the exponential growth phase [9].
In this context, the production of lasiodiplodan from glycerol as a carbon source by the fungal strain L. theobromae MMPI in a shake flask revealed that the peak lasiodiplodan was measured at a 72-h time course [9]. A similar pattern was observed by Crognale et al. [50], who found that the highest β-glucan production by the filamentous fungus Botryosphaeria rhodina DABAC-P82 was obtained at 72 h fermentation in the shake flask.
The present study showed that the production of lasiodiplodan by the strain L. theobromae CCT3966 was a growth-associated process. Similar findings were reported by Cunha et al. [1] who cultivated the strain L. theobromae MMPI on glucose in a shake flask with triggering the maximum lasiodiplodan production in the exponential growth phase.
Consumption of glucose as a carbon source occurred during the whole fermentation process, while it was not consumed completely. A similar observation was reported by Cunha et al. [1], who cultivated the strain L. theobromae MMPI in a shake flask to produce lasiodiplodan from glucose. They noted that glucose was utilized during the whole 120-h course of fermentation, and at this stage about 30% glucose remained in the culture medium.
The study fulfilled by Philippini et al. [13] revealed that the FTIR of glucan polymer lasiodiplodan produced by the strain L. theobromae CCT3966 from corn bran acid hydrolysate showed a β-type conformation. Similar to the current study, Kagimura et al. [10] showed that the lasiodiplodan produced by L. theobromae MMPI had a structure with a very wide non-crystalline peak in the spectra 20–22° (2θ). In this line, the XRD curve of β-glucan produced by Saccharomyces cerevisiae exhibited an amorphous phenomenon in which a peak near to 22° (2θ) was observed [51].

5. Conclusions

This research showed the feasibility of lasiodiplodan production using the fermentable glucose obtained from sugarcane straw pretreated by HNO3 (1% v/v) and NaOH (1% w/v). The statistical analysis of the pretreatment results showed that pretreatments were significantly improved cellulose content and removal of hemicellulose and lignin components of sugarcane straw (p < 0.01). Statistical study on the glucose produced in enzymatic hydrolysis of pretreated sugarcane straw revealed that enzymatic hydrolysis contributes to the release of high quantity of glucose during the hydrolysis process (p < 0.01). The maximum lasiodiplodan yield and productivity of 0.054 gg−1 and 0.016 gL−1h−1, respectively, were obtained at 72 h fermentation time. Kinetic study of the fermentation process revealed that the experimental biosynthesis of lasiodiplodan from sugarcane straw hydrolysate followed the trend generated by the kinetic model. The chemical structure of lasiodiplodan produced showed β-glucan structure. The statistical analysis of the kinetic models using R2 value MSE parameters indicated that the experimental results were sufficiently consistent with the simulated models. Sugarcane straw represents a promising substrate for fermentative production of lasiodiplodan and further studies can be conducted for scaling up the production of this biopolymer in the bioreactor.

Author Contributions

Conceptualization, S.S.d.S. and P.A.; methodology, P.A. and J.J.A.; validation, P.A.; formal analysis, P.A.; investigation, P.A.; resources, S.S.d.S. and J.C.d.S.; data curation, P.A.; writing—original draft preparation, P.A.; writing—review and editing, J.J.A., R.R.P., F.A.F.A., A.P.I., M.A. and J.C.d.S.; visualization, P.A.; supervision, S.S.d.S.; project administration, J.C.d.S. and S.S.d.S.; funding acquisition, S.S.d.S. All authors have read and agreed to the published version of the manuscript.

Funding

This work was financially supported by the São Paulo Research Foundation—FAPESP (FAPESP Process No. 2018/14095-7) in São Paulo, Brazil. This work was also supported by Thematic Project of FAPESP (FAPESP Process No. 2016/10636-8).

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

The data presented in this study are available on request from the corresponding author. The data are not publicly available due to privacy issue.

Acknowledgments

The authors would like to acknowledge CNPq (Conselho Nacional de Desenvolvimento Científico e Tecnológico), Process No. 303943/2017-3, Brazil. The authors would also like to acknowledge PROFIDES—México for their approved bilateral project. API is highly thankful to SERB, Department of Science and Technology, Government of India for Ramanujan Fellowship (File No. RJF/2019/000044). The authors would also like to acknowledge Fundação André Tosello Pesquisa e Tecnologia (Campinas, SP, Brazil) for providing the strain Lasiodiplodia theobromae CCT3966.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Cunha, M.A.A.; Turmina, J.A.; Ivanov, R.C.; Barroso, R.R.; Marques, P.T.; Fonseca, E.A.; Fortes, Z.B.; Dekker, R.F.; Khaper, N.; Barbosa, A.M. Lasiodiplodan, an exocellular (1-6)-b-D-glucan from Lasiodiplodia theobromae MMPI: Production on glucose, fermentation kinetics, rheology and anti-proliferative activity. J. Ind. Microbiol. Biotechnol. 2012, 39, 1179–1188. [Google Scholar] [CrossRef] [PubMed]
  2. Varelas, V.; Tataridis, P.; Liouni, M.; Nerantzis, E.T. Valorization of winery spent yeast waste biomass as a new source for the production of β-glucan. Waste Biomass Valorization 2016, 7, 807–817. [Google Scholar] [CrossRef]
  3. Abdeshahian, P.; Ascencio, J.J.; Philippini, R.R.; Antunes, F.A.F.; de Carvalho, A.S.; dos Santos, J.C.; da Silva, S.S. Valorization of lignocellulosic biomass and agri-food processing wastes for production of glucan polymer. Waste Biomass Valorization 2021, 12, 2915–2931. [Google Scholar] [CrossRef]
  4. Oliveira, K.S.; Di Bastiani, M.; Cordeiro, L.M.; Costa, M.F.; Toledo, K.A.; Iacomini, M.; Babosa, A.M.; Dekker, R.F.; Nascimento, V.M. (1→6)- and (1→3) (1→6)-β-glucans from Lasiodiplodia theobromae MMBJ: Structural characterization and pro-inflammatory activity. Carbohydr. Polym. 2015, 20, 539–546. [Google Scholar] [CrossRef] [PubMed]
  5. Cunha, M.A.A.; Santos, V.A.Q.; Calegari, G.C.; Luna, W.N.S.; Marin, S.L.A.; Dekker, R.F.H.; Barbosa-Dekker, A.M. Structure and biological properties of lasiodiplodan: Anuncommon fungal exopolysaccharide of the (1→6)-β-D-glucan type. In Extracellular Sugar-Based Biopolymers Matrices; Cohen, E., Merzendorfer, H., Eds.; Springer Nature: Cham, Switzerland, 2019; pp. 409–432. [Google Scholar]
  6. Theis, T.V.; Calegari, G.C.; Santos, V.A.Q.; Junior, H.E.Z.; Barbosa, A.M.; Dekker, R.F.H.; Cunha, M.A.A. Exocellular (1→6)-β-D-glucan (Lasiodiplodan): Carboxymethylation, thermal behavior, antioxidant and antimicrobial activity. Am. J. Immunol. 2017, 13, 19–33. [Google Scholar] [CrossRef]
  7. Ferreira, R.G.; Azzoni, A.R.; Freitas, S. Review on the production cost of lignocellulose-degrading enzymes. Biofuel Bioprod. Biorefin. 2021, 15, 85–99. [Google Scholar] [CrossRef]
  8. Kagimura, F.Y.; Cunha, M.A.A.; Theis, T.V.; Barbosa, A.M.; Teixeira, S.D.; Dekker, R.F.H. Production of the exopolysaccharide lasiodiplodan in a stirred-tank bioreactor. Synerg. Scyentífica UTFPR 2015, 10, 1–8. [Google Scholar]
  9. Tabuchi, S.C.T.; Martiniano, S.E.; Cunha, M.A.A.; Barbosa-Dekke, A.M.; Dekker, R.F.H.; Prata, A.M.R. Kinetic Study of Lasiodiplodan Production by Lasiodiplodia theobromae MMPI in a Low-Shear Aerated and Agitated Bioreactor. J. Polym. Environ. 2021, 29, 89–102. [Google Scholar] [CrossRef]
  10. Kagimura, F.Y.; Cunha, M.A.A.; Theis, T.V.; Malfatti, C.R.M.; Dekker, R.F.H.; Barbosa, A.M.; Teixeira, S.D.; Salomé, K. Carboxymethylation of (1 → 6)- β-glucan (lasiodiplodan): Preparation, characterization and antioxidant evaluation. Carbohydr. Polym. 2015, 127, 390–399. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  11. Pflügl, S.; Marx, H.; Mattanovich, D.; Sauer, M. Heading for an economic industrial upgrading of crude glycerol from biodiesel production to 1,3-propanediol by Lactobacillus diolivorans. Bioresour. Technol. 2014, 152, 499–504. [Google Scholar] [CrossRef] [PubMed]
  12. Li, Y.; Zhu, S.; Ge, X. Co-production of 1,3-propanediol and 2,3-butanediol from waste lard by co-cultivation of Pseudomonas alcaligenes and Klebsiella pneumonia. Curr. Microbiol. 2019, 76, 415–424. [Google Scholar] [CrossRef]
  13. Philippini, R.R.; Martiniano, S.E.; Marcelino, P.R.F.; Chandel, A.K.; dos Santos, J.C.; da Silva, S.S. Production of β-glucan exopolysaccharide lasiodiplodan by Lasiodiplodia theobromae CCT3966 from corn bran acid hydrolysate. Appl. Microbiol. Biotechnol. 2021, 105, 2319–2332. [Google Scholar] [CrossRef] [PubMed]
  14. Cho, E.J.; Trinh, L.T.P.; Song, Y.; Lee, Y.G.; Bae, Y.-J. Bioconversion of biomass waste into high value chemicals. Bioresour. Technol. 2020, 298, 122386. [Google Scholar] [CrossRef] [PubMed]
  15. Sarsaiya, S.; Jaina, A.; Awasthic, S.K.; Duanc, Y.; Awasthic, M.K.; Shia, J. Microbial dynamics for lignocellulosic waste bioconversion and its importance with modern circular economy, challenges and future perspectives. Bioresour. Technol. 2019, 291, 121905. [Google Scholar] [CrossRef] [PubMed]
  16. Ascencio, J.J.; Philippini, R.R.; Gomes, F.M.; Pereira, F.M.; da Silva, S.S.; Kumar, V.; Chandel, A.K. Comparative highly efficient production of β-glucan by Lasiodiplodia theobromae CCT3966 and its multiscale characterization. Fermentation 2021, 7, 108. [Google Scholar] [CrossRef]
  17. Hernández-Pérez, A.F.; de Arruda, P.V.; Felipe, M.G.A. Sugarcane straw as a feedstock for xylitol production by Candida guilliermondii FTI 20037. Braz. J. Microbiol. 2016, 47, 489–496. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  18. de Aquino, G.S.; de Conti Medina, C.; da Costa, D.C.; Shahab, M.; Santiago, A.D. Sugarcane straw management and its impact on production and development of rations. Ind. Crops Prod. 2017, 102, 58–64. [Google Scholar] [CrossRef] [Green Version]
  19. Carvalho, D.M.; Sevastyanova, O.; Penna, L.S.; Silva, B.P.; Lindstromb, M.E.; Colodette, J.L. Assessment of chemical transformations in eucalyptus, sugarcane bagasse and straw during hydrothermal, dilute acid, and alkaline pretreatments. Ind. Crops Prod. 2015, 73, 118–126. [Google Scholar] [CrossRef]
  20. Production of Sugar Cane in Brazil from Crop Year 2010/11 to 2020/21. Statista. Available online: https://www.statista.com/statistics/742530/sugar-cane-production-volume-brazil/ (accessed on 15 June 2021).
  21. Menandro, L.M.S.; Cantarella, H.; Franco, H.C.J.; Kölln, O.T.; Pimenta, M.T.B.; Sanches, G.M.; Rabelo, S.C.; Carvalho, J.L.N. Comprehensive assessment of sugarcane straw: Implications for biomass and bioenergy production. Biofuel Bioprod. Biorefin. 2017, 11, 488–504. [Google Scholar] [CrossRef]
  22. Moutta, R.O.; Silva, M.C.; Corrales, R.C.N.R.; Cerullo, M.A.S.; Ferreira-Leitão, V.S.; Bon, E.P.S. Comparative response and structural characterization of sugarcane bagasse, straw and bagasse-straw 1:1 mixtures subjected to hydrothermal pretreatment and enzymatic conversion. J. Microb. Biochem. Technol. 2013, 12, 1–8. [Google Scholar]
  23. Gómez, E.O.; Souza, R.T.G.; Rocha, G.J.M.; Almeida, E.; Cortez, L.A.B. Sugarcane trash as feedstock for second generation processes. In Sugarcane Bioethanol—R&D for Productivity and Sustainability; Cortez, L.A.B., Ed.; Blucher: São Paulo, Brazil, 2014; pp. 637–660. [Google Scholar]
  24. Lachos-Perez, D.; Tompsett, G.A.; Guerra, P.; Timko, M.T.; Rostagno, M.A.; Martínez, J.; Forster-Carneiro, T. Sugars and char formation on subcritical water hydrolysis of sugarcane straw. Bioresour. Technol. 2017, 243, 1069–1077. [Google Scholar] [CrossRef] [PubMed]
  25. Candido, R.G.; Mori, N.R.; Gonçalves, A.R. Sugarcane straw as feedstock for 2G ethanol: Evaluation of pretreatments and enzymatic hydrolysis. Ind. Crops Prod. 2019, 142, 111845. [Google Scholar] [CrossRef]
  26. Chukwuma, O.B.; Rafatullah, M.; Tajarudin, H.A.; Ismail, N. Lignocellulolytic enzymes in biotechnological and industrial processes: A review. Sustainability 2020, 12, 7282. [Google Scholar] [CrossRef]
  27. Ferdeș, M.; Dincă, M.N.; Moiceanu, G.; Zăbavă, B.S.; Paraschiv, G. Microorganisms and enzymes used in the biological pretreatment of the substrate to enhance biogas production: A review. Sustainability 2020, 12, 7205. [Google Scholar] [CrossRef]
  28. Chaudhary, N.; Qazi, J.I.; Irfan, M. Isolation and identification of cellulolytic and ethanologenic bacteria from soil. Iran. J. Sci. Technol. Trans. Sci. 2017, 41, 551–555. [Google Scholar] [CrossRef]
  29. Mulyaningtyas, A.; Sediawan, W.B. Effect of combined pretreatment of lignocellulose and the kinetics of its subsequent bioconversion by Aspergillus niger. Biocatal. Agric. Biotechnol. 2019, 21, 101292. [Google Scholar] [CrossRef]
  30. Kang, Q.; Appels, L.; Tan, T.; Dewil, R. Bioethanol from lignocellulosic biomass: Current findings determine research priorities. Sci. World J. 2014, 1–13. [Google Scholar] [CrossRef]
  31. Zaafouri, K.; Ziadi, M.; Trabelsi, A.B.H.; Mekni, S.; Aïssi, B.; Alaya, M.; Bergaoui, L.; Hamdi, M. Optimization of hydrothermal and diluted acid pretreatments of Tunisian Luffa cylindrica (L.) fibers for 2G bioethanol production through the cubic central composite experimental design CCD: Response surface methodology. BioMed. Res. Int. 2017, 2017, 1–14. [Google Scholar] [CrossRef] [PubMed]
  32. Miléo, P.C.; Rodrigues, L.C.; Gandara, M.; Rocha, G.J.M.; Goncalves, A.R. Cellulose. In biorefinary: Fibres obtainment form sugarcane bagasse and pretreated by diluted acid and delignified by alkali. In Proceedings of the 20th European Biomass Conference and Exhibition, Milan, Italy, 18–22 June 2012. [Google Scholar]
  33. De Jong, E.; Gosselink, R.J.A. lignocellulose-based chemical products. In Bioenergy Research: Advances and Applications; Gupta, V.K., Tuohy, M.G., Kubicek, C.P., Saddler, J., Xu, F., Eds.; Elsevier: Amsterdam, The Netherlands, 2014; pp. 277–313. [Google Scholar]
  34. Jia, Z.; Zheng, Y.; Zhou, J. Effects of different pretreatment methods on the enzymatic hydrolysis of cassava residue. BioResources 2019, 14, 6060–6078. [Google Scholar] [CrossRef]
  35. Dzieko´nska-Kubczak, U.; Berłowska, J.; Dziugan, P.; Patelski, P.; Pielech-Przybylska, K.; Balcerek, M. Nitric acid pretreatment of jerusalem artichoke stalks for enzymatic saccharification and bioethanol production. Energies 2018, 11, 2153. [Google Scholar] [CrossRef] [Green Version]
  36. Abdeshahian, P.; Ascencio, J.J.; Philippini, R.R.; Antunes, F.A.F.; dos Santos, J.C.; da Silva, S.S. Utilization of sugarcane straw for production of β-glucan biopolymer by Lasiodiplodia theobromae CCT3966 in batch fermentation process. Bioresour. Technol. 2020, 314, 123716. [Google Scholar] [CrossRef] [PubMed]
  37. Kusmiyati, K.; Anarki, S.T.; Nugroho, S.W.; Widiastutik, R.; Hadiyanto, H. Effects of dilute acid and alkaline pretreatments on enzymatic saccharification of palm tree trunk waste for bioethanol produc-tion. Bull. Chem. React. Eng. Catal. 2019, 14, 705–714. [Google Scholar] [CrossRef]
  38. Tri, C.L.; Khuong, L.D.; Kamei, I. The improvement of sodium hydroxide pretreatment in bioethanol production from Japanese bamboo Phyllostachys edulis using the white rot fungus Phlebia sp. MG-60. Int. Biodeterior. Biodegradation 2018, 133, 86–92. [Google Scholar] [CrossRef]
  39. Santos-Rocha, M.S.R.; Pratto, B.; Corrêa, L.J.; Badino, A.C.; Almeida, R.M.R.G.; Cruz, A.J.G. Assessment of different biomass feeding strategies for improving the enzymatic hydrolysis of sugarcane straw. Ind. Crops Prod. 2018, 125, 293–302. [Google Scholar] [CrossRef]
  40. Zhang, Q.; Sun, J.; Wang, Z.; Hang, H.; Zhao, W.; Zhuang, Y.; Chu, J. Kinetic analysis of curdlan production by Alcaligenes faecalis with maltose, sucrose, glucose and fructose as carbon sources. Bioresour. Technol. 2018, 259, 319–324. [Google Scholar] [CrossRef] [PubMed]
  41. Luedeking, R.; Piret, E.L. A kinetic study of the lactic acid fermentation. Batch process at controlled pH. Biotechnol. Bioeng. 2000, 67, 636–644. [Google Scholar] [CrossRef]
  42. Sluiter, A.; Hames, B.; Ruiz, R.; Scarlata, C.; Sluiter, J.; Templeton, D.; Crocker, D. Determination of Structural Carbohydrates and Lignin in Biomass; National Renewable Energy Laboratory: Golden, CO, USA, 2011. [Google Scholar]
  43. Moutta, R.O.; Ferreira-Leitao, V.S.; Bon, E.P.S. Enzymatic hydrolysis of sugarcane bagasse and straw mixtures pretreated with diluted acid. Biocatal. Biotransformation 2014, 32, 93–100. [Google Scholar] [CrossRef]
  44. Cortez, D.V.; Roberto, I.C.; Barbosa, M.H.P.; Milagres, A.M.F. Evaluation of cellulosic and hemicellulosic hydrolysate fermentability from sugarcane bagasse hyborids with different compositions. Biomass Convers. Biorefin. 2014, 4, 351–356. [Google Scholar] [CrossRef]
  45. Guilherme, A.A.; Dantas, P.V.F.; Soares, J.C.J.; Santos, E.S.; Fernandes, F.A.N.; Macedo, G.R. Pretreatments and enzymatic hydrolysis of sugarcane bagasse aiming at the enhancement of the yield of glucose and xylose. Braz. J. Chem. Eng. 2017, 34, 937–947. [Google Scholar] [CrossRef] [Green Version]
  46. Rocha, M.S.R.S.; Pratto, B.; Júnior, R.S.; Almeida, R.M.R.G.; Cruz, A.J.G. A kinetic model for hydrothermal pretreatment of sugarcane straw. Bioresour. Technol. 2017, 228, 176–185. [Google Scholar] [CrossRef]
  47. Alrumman, S.A. Enzymatic saccharification and fermentation of cellulosic date palm wastes to glucose and lactic acid. Braz. J. Microbiol. 2016, 47, 110–119. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  48. Pereira, S.C.; Maehara, L.; Machado, C.M.M.; Farinas, C.S. 2G ethanol from the whole sugarcane lignocellulosic biomass. Biotechnol. Biofuels 2015, 8, 44. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  49. Oliveira, L.R.M.; Nascimento, V.M.; Goncalves, A.R.; Rocha, G.J.M. Combined process system for the production of bioethanol fromsugarcane straw. Ind. Crops Prod. 2014, 58, 1–7. [Google Scholar] [CrossRef]
  50. Crognale, S.; Federici, F.; Petruccioli, M. β-Glucan production by Botryosphaeria rhodina on undiluted olive-mill wastewaters. Biotechnol. Lett. 2003, 25, 2013–2015. [Google Scholar] [CrossRef] [PubMed]
  51. Novak, M.; Synytsya, A.; Gedeon, O.; Slepička, P.; Prochazka, V.; Synytsya, A.; Blahovec, J.; Hejlova, A.; Čopikova, J. Yeast β (1-3), (1-6)-D-glucan films: Preparation and characterization of some structural and physical properties. Carbohydr. Polym. 2012, 87, 2496–2504. [Google Scholar] [CrossRef]
Figure 1. SEM images of the pretreated sugarcane straw with magnification of 1000×: (A) HNO3 pretreated sugarcane straw; (B) NaOH pretreated sugarcane straw following acid pretreatment.
Figure 1. SEM images of the pretreated sugarcane straw with magnification of 1000×: (A) HNO3 pretreated sugarcane straw; (B) NaOH pretreated sugarcane straw following acid pretreatment.
Sustainability 13 09697 g001
Figure 2. The profile of enzymatic hydrolysis of pretreated sugarcane straw during 72 h of hydrolysis time: (A) concentration of glucose released; (B) cellulose to glucose conversion percentage.
Figure 2. The profile of enzymatic hydrolysis of pretreated sugarcane straw during 72 h of hydrolysis time: (A) concentration of glucose released; (B) cellulose to glucose conversion percentage.
Sustainability 13 09697 g002aSustainability 13 09697 g002b
Figure 3. The profile of time course of fermentation process of L. theobromae CCT3966 in sugarcane straw hydrolysate: (A) the fungal growth, (B) lasiodiplodan production, (C) glucose consumption.
Figure 3. The profile of time course of fermentation process of L. theobromae CCT3966 in sugarcane straw hydrolysate: (A) the fungal growth, (B) lasiodiplodan production, (C) glucose consumption.
Sustainability 13 09697 g003
Figure 4. Chemical characterization of lasiodiplodan produced from sugarcane straw hydrolysate by L. theobromae CCT 3966: (A) FT-IR spectra, (B) standard X-ray diffraction profile.
Figure 4. Chemical characterization of lasiodiplodan produced from sugarcane straw hydrolysate by L. theobromae CCT 3966: (A) FT-IR spectra, (B) standard X-ray diffraction profile.
Sustainability 13 09697 g004
Table 1. Chemical composition of sugarcane straw: untreated biomass, after dilute acid (HNO3 1% v/v) pretreatment, and after alkaline (NaOH 1% w/v) pretreatment a.
Table 1. Chemical composition of sugarcane straw: untreated biomass, after dilute acid (HNO3 1% v/v) pretreatment, and after alkaline (NaOH 1% w/v) pretreatment a.
ComponentUntreated Biomass (%) cAfter Acid
Pretreatment (%)
After Alkaline
Pretreatment (%)
Cellulose41.25 ± 1.1062.28 ± 1.1182.22 ± 1.04
Hemicelluloses35.17 ± 0.303.53 ± 0.40ND b
Lignin17.25 ± 3.3932.15 ± 0.4416.28 ± 1.35
Ash2.81 ± 1.432.265 ± 0.0071.73 ± 0.29
a Values based on mean ± standard deviation; b ND: Not Detected; c [36].
Table 2. The kinetic parameters for lasiodiplodan production from sugarcane straw hydrolysate in batch fermentation.
Table 2. The kinetic parameters for lasiodiplodan production from sugarcane straw hydrolysate in batch fermentation.
Kinetic ParameterValue
X o 0.13 gL−1
X m a x 3.01 gL−1
μ 0.06 h−1
α 4.54 gg−1
Y p / s 0.054 gg−1
Q p 0.016 gL−1h−1
Y x / s 0.09 gg−1
X o , initial biomass; X m a x , the highest biomass production; μ , maximum.specific growth rate; α , lasiodiplodan production coefficient; Y p / s , yield of lasiodiplodan production; Q p , volumetric productivity of lasiodiplodan production; Y x / s , fungal biomass yield.
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Abdeshahian, P.; Ascencio, J.J.; Philippini, R.R.; Antunes, F.A.F.; Ingle, A.P.; Abdeshahian, M.; Santos, J.C.d.; Silva, S.S.d. Fermentative Production of Lasiodiplodan by Lasiodiplodia theobromae CCT3966 from Pretreated Sugarcane Straw. Sustainability 2021, 13, 9697. https://doi.org/10.3390/su13179697

AMA Style

Abdeshahian P, Ascencio JJ, Philippini RR, Antunes FAF, Ingle AP, Abdeshahian M, Santos JCd, Silva SSd. Fermentative Production of Lasiodiplodan by Lasiodiplodia theobromae CCT3966 from Pretreated Sugarcane Straw. Sustainability. 2021; 13(17):9697. https://doi.org/10.3390/su13179697

Chicago/Turabian Style

Abdeshahian, Peyman, Jesús Jiménez Ascencio, Rafael R. Philippini, Felipe Antonio Fernandes Antunes, Avinash P. Ingle, Mojgan Abdeshahian, Júlio César dos Santos, and Silvio Silvério da Silva. 2021. "Fermentative Production of Lasiodiplodan by Lasiodiplodia theobromae CCT3966 from Pretreated Sugarcane Straw" Sustainability 13, no. 17: 9697. https://doi.org/10.3390/su13179697

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop