Next Article in Journal
Mental Well-Being during COVID-19: A Cross-Sectional Study of Fly-In Fly-Out Workers in the Mining Industry in Australia
Next Article in Special Issue
Decoupling and Decomposition Analysis of Agricultural Carbon Emissions: Evidence from Heilongjiang Province, China
Previous Article in Journal
Misinformation, Fears and Adherence to Preventive Measures during the Early Phase of COVID-19 Pandemic: A Cross-Sectional Study in Poland
Previous Article in Special Issue
Research on the Spatio-Temporal Impacts of Environmental Factors on the Fresh Agricultural Product Supply Chain and the Spatial Differentiation Issue—An Empirical Research on 31 Chinese Provinces
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Energy and Environmental Assessment of Steam Management Optimization in an Ethylene Plant

1
Department of Chemical and Biochemical Engineering, Faculty of Chemical and Food Technology, Slovak University of Technology, Radlinského 9, 812 37 Bratislava, Slovakia
2
SLOVNAFT, a.s., Vlčie Hrdlo 1, 824 12 Bratislava, Slovakia
3
GRUCON, s.r.o., Nezábudková 24, 821 02 Bratislava, Slovakia
*
Author to whom correspondence should be addressed.
Int. J. Environ. Res. Public Health 2021, 18(22), 12267; https://doi.org/10.3390/ijerph182212267
Submission received: 20 October 2021 / Revised: 18 November 2021 / Accepted: 20 November 2021 / Published: 22 November 2021
(This article belongs to the Special Issue Future and Feature Paper in Environment and Applied Ecology)

Abstract

:
Steam crackers (ethylene plants) belong to the most complex industrial plants and offer significant potential for energy-saving translated into the reduction of greenhouse gas emissions. Steam export to or import from adjacent units or complexes can boost the associated financial benefit, but its energy and environmental impact are questionable. A study was carried out on a medium-capacity ethylene plant using field data to: 1. Estimate the energy savings potential achievable by optimizing internal steam management and optimizing steam export/import; 2. Quantify the associated change in air pollutant emissions; 3. Analyze the impact of the increasing carbon price on the measures adopted. Internal steam management optimization yielded steam let-down rate minimization and resulted in a 5% (87 TJ/year) reduction in steam cracker’s steam boiler fuel consumption and the associated cut of CO2 emissions by almost 4900 t/year and that of NOx emissions by more than 5 t/year. Steam import to the ethylene plant from the refinery proved to be purely economic-driven, as it increased the net fuel consumption of the ethylene plant and the refinery complex by 12 TJ/year and resulted in an increase of net emissions of nearly all considered air pollutants (more than 7000 t/year of CO2, over 15 t/year of NOx, over 18 t/year of SOx) except for CO, where the net change was almost zero. The effect of external emissions change due to the associated backpressure electricity production surplus (over 11 GWh/year) was too low to compensate for this increase unless fossil fuel-based electricity production was considered. The increase of carbon price impact on the internal steam management optimization economics was favorable, while a switch to steam export from the ethylene plant, instead of steam import, might be feasible if the carbon price increased to over 100 €/tCO2.

1. Introduction

1.1. Overview and Literature Survey

The deepening climate crisis makes it imperative to substantially reduce anthropogenic carbon emissions. Reduced industrial emissions production has the potential to contribute visibly to achieving this goal, as they globally represent around a third of total anthropogenic emissions [1,2]. Around 40% of industrial emissions can be attributed to the production of energies and media consumed in production processes [3,4]. Electricity and steam production, distribution, and consumption systems are ideal candidates for design and operation optimization [5,6] within the scope of energy management systems implementation [7,8]. The drivers of such activities include several technical and non-technical aspects, such as sustainable industrial production [9,10,11], labeling of products as ‘green’ [12], increasing price of carbon emissions [13,14], as well as the persistent need for an increase in production efficiency [15] to remain innovative and competitive on the market [16,17] and to comply with the legislation [18].
In addition to electric energy, virtually consumed in any production process, the production of heat carriers contributes to both operational expenses and greenhouse gas (GHG) emissions [19,20]. Among these, steam has a prominent position especially in heavy industries, including but not limited to: steel and ironmaking [21,22], pulp and paper [23,24], ammonia and fertilizer production [25], refining and petrochemistry [26,27]. As it results from the historical development of both technologies and industrial plants, steam production in such industries is generally a mix of centralized and decentralized sources [28]. The central industrial combined heat and power plant (CHP) serves as a marginal steam source, while a substantial amount of steam is produced and consumed directly at the production plants [29]. Industrial steam networks are often complicated systems of interconnected pipelines with steam sources and consumers connected to several steam pressure levels [30,31]. Managing such systems requires suitable decision-making tools and sufficient flexibility, which is usually provided by CHP and process steam drives that can be alternated with electrodrives [32,33].
Considering the refining and petrochemical industry, individual production units are typically assembled in organized production groups, refineries [34], that can be a part of even larger chemical complexes and industrial parks [35,36]. Typically, three to five main steam pressure levels satisfy the needs for delivered steam quality [6]. CHPs are commonly equipped with several steam boilers producing high-pressure steam and several steam turbines to cope with the varying demand for steam at individual pressure levels [37]. Liquid fuels (heating oils, residues of conversion processes) or gaseous fuels (refinery gases, offgases, and natural gas) are fired in such boilers. Steam turbines cogenerate electric energy, covering a part of the electricity demand of the refinery, while extracted and backpressure steam is partly used in the CHP and the rest is exported to the refinery [38,39]. On the other hand, decentralized steam production in production units is rarely carried out on purpose; residual heat content of material streams or flue gas from refinery furnaces is an almost exclusive heat source for steam production [40]. Among these facilities, ethylene plants (Steam Crackers, SC) are examples of deeply energy- and process-integrated units, combining high-pressure steam production in convection sections of pyrolysis furnaces and dedicated steam boilers [33,41,42]. Produced steam is expanded in large steam turbines driving key process equipment [43]. The extracted steam is used in smaller process steam drives or for heating and other purposes [44,45]. The steam system in such plants is supplemented by let-down stations and steam export to or import from the main steam network is possible if the plant is integrated into a larger industrial complex [46,47]. Parallel production of steam at various pressure levels and mechanical energy [48,49] in SC can be, together with the production of steam and electric energy in industrial CHP, termed cogeneration while the whole system, which produces energies and materials, is a polygeneration plant [50,51]. The efficiency of heat and power production (mechanical energy), as well as fuel costs and GHG emissions in an industrial CHP and SC, can vary over time due to many factors. This opens the possibility of combined energetic-economic-environmental (3E) optimization [52,53]. Integration of petrochemical plants and refining plants comprises several material streams—feed [54], hydrogen [55], offgases [56], semi-finished products and products [46,57], and utilities [58], and thus poses an extraordinarily complex optimization problem [59].
Zhao et al. (2017) [46] and Ketabchi et al. (2019) [47] explored the potential of material integration of an ethylene plant in an oil refinery. Taking advantage of the synergies of both plants’ operations, a significant increase in their profit could be achieved based on optimization calculations. The most recent studies by Gong et al. (2019) [57] and Dai et al. (2021) [53] focused on material efficiency within an ethylene plant either by optimizing the reactor part [53] or the back-end separation part [57]. Shen et al. [58] proposed a framework for optimizing the energy structure of a standalone ethylene plant, comprising multiple steam pressure levels, steam sources, consumers, and steam drives operating between several pressure levels. Optimization of such a system led to increased use of electrodrives instead of steam drives and to a reduced amount of steam sent through let-down stations, whereby fuel energy consumption reduction of around 14% could be achieved. Zhao et al. [33] successfully applied similar proposals in a study on optimizing the operation of another ethylene plant. In a more recent study, Shen et al. (2021) [60] optimized a part of the SC gas plant in terms of exergy efficiency and processing costs. Wang et al. (2020) [61] proposed a framework for multiobjective optimization of production plants and applied it to the cryogenic separation part of an ethylene plant. As a result, a tradeoff was found between increased propylene production and reduced operational expenses. Numerous recent studies document the ongoing intense effort to reduce the operational expenses and to increase the material and energy efficiency of ethylene plants.

1.2. Contribution of This Study

The above survey has shown that optimizing energy consumption and process features in steam cracker plants is a promising means of achieving material and energy efficiency improvement goals. However, many studies dedicated to optimizing ethylene plants focus solely on the CO2 balance or omit the environmental problems entirely. As examples, studies by Li et al. (2013) [41], Gong et al. (2019) [57], Shen et al. (2019) [58], and Zhao et al. (2019) [33] delivered important findings related to the potential reduction in energy consumption as a result of optimized SC operation, while Chen et al. (2020) [62], Geng et al. (2020) [59], and Dai et al. (2021) [53] explored both energy efficiency and CO2 emissions aspects. This is in line with recent developments in industrial processes and energy systems optimization [63,64], where the calculation of CO2 emissions is a widely adopted means of assessing the environmental impact [52,65]; only rarely supplemented by calculation of other GHG emissions [66,67] or expressed via CO2 equivalent [68,69]. The analysis of GHGs other than CO2 is, on the other hand, common in the evaluation and optimization of combustion processes and power plants [70,71].
To the best of our knowledge, there are no relevant studies in the field of SC energy management optimization addressing other major pollutants and employing field data at the same time.
Thereby, a knowledge gap is identified, namely:
  • Whether and how are energy savings achievable by internal SC energy management optimization affected by the possibility of steam import/export to/from an SC?
  • What does the resulting balance of the main air pollutants look like, and to what extent can the feasibility of energy costs saving measures be affected by the increasing carbon tax?
The aim of this study is to provide answers to these questions with the help of field data from a real SC integrated in a refinery.

2. Materials and Methods

2.1. Steam Cracker Steam System

A mid-capacity Steam Cracker located in the European Union was selected as a model case. It is material- and energy-integrated in a refinery and processes both gases and gasoline. It has a complex steam system that can act as a standalone system or, if needed, is capable of importing or exporting steam from/to the outer steam network as depicted in Figure 1. The steam network operates at six different pressure levels with the following typical parameters.
  • SS (superhigh pressure) steam: 11.0 MPa (g), 520 °C;
  • HS steam: (high pressure) 3.5 MPa (g), 350 °C;
  • MS steam: (intermediate pressure) 1.2 MPa (g), 250 °C;
  • LS steam: (low pressure) 0.4 MPa (g), 170 °C;
  • PS steam: (very low pressure) 0.25 MPa (g), 138 °C;
  • DS steam: (dilution steam) 0.7 MPa, 190 °C.
SS steam is produced internally in cracking furnaces and in an auxiliary steam boiler. The contributions of steam produced in the furnaces and boiler were almost equal in the past, as shown in Figure 2.
However, the share of steam produced in furnaces increased in recent years, especially due to increased SC feedstock processing (2017–2019). The corresponding effect can be seen in Table 1 in the decreasing values of SS steam consumption per % of specific ethylene production, which indicates that the plant operates more efficiently at higher throughputs. SS steam is consumed in combined extraction-condensing steam drives driving process gas compressors. Excess steam is reduced in the let-down station to HS steam. Similarly, HS and MS steam is used to drive various steam drives, and the rest is reduced to lower pressure level steam. LS steam is used mostly as a heating medium in fractionators, boiler feed water (BFW) preparation, or steam tracing. In addition, HS, MS, and LS steam export or import are possible; however, only HS and LS steam import are usually used. PS steam is produced by LS steam reduction and is used as a heating medium in some heat exchangers and vessels. DS steam is used in the process as a dilution stream added directly to the feedstock.
The increasing share of steam throttling presented in Table 2 is an indication of a nonfunctional regulation element. Let-down valve ‘A’ lost its regulation ability due to erosion under extreme operating conditions. The valve opening was rather constant at 14% before the turnaround in 2019, yet the steam inlet flows increased significantly within one year.
An external energy audit performed in 2013 recommended the installation of a parallel let-down valve with a smaller capacity and an independent regulation to ensure smooth and functional regulation of the SS steam network. This was in line with the best practice, which recommended reducing the amount of steam flowing through let-down stations to a minimum. Preliminary analysis found two possible benefits:
  • Direct fuel (natural gas) savings are expected due to more efficient co-generative HS steam production by extraction from steam drives instead of SS to HS steam throttling, translated into a reduced condensing load of the steam drives. Thus, an improvement in the energy efficiency of SC and the whole refinery is expected. In addition, fewer GHG emissions will be produced.
  • HS and LS steam import will be enabled due to less steam being produced internally. Imported steam is usually produced from cheaper fuel (mixed petroleum residue, MPR, which is usually in excess). Additional extraction electricity generation will be possible thanks to the increased steam supply from the CHP unit. These effects contribute to better economic results. On the other hand, there is a negative environmental effect of MPR fuel utilization, as its combustion produces more greenhouse gases (GHGs) than that of natural gas.
Implementation of the energy audit recommendations took almost six years.

2.2. Combined Heat and Power Unit

Combined heat and power unit (CHP) serves as a marginal steam source for the refinery, balancing steam demand and supplying steam at three pressure levels: 3.5 MPa (g) (HS), 1.0 MPa (g) (MS), and 0.4 MPa (g) (LS). It comprises several MPR-fired steam boilers that supply high-pressure steam (9 MPa, 535 °C) to a battery of steam turbines producing backpressure and condensing electric energy and steam at various pressure levels, both for own consumption and for export. LS export is the most sensitive to ambient temperature as it is predominantly used for space heating and steam tracing of process streams. During warmer months, especially from June to September, LS is occasionally vented into the atmosphere to prevent a stall in the LS steam mains and thus to avoid excessive steam condensation followed by corrosion and potential equipment failure. A more detailed description of the layout and operation of the CHP unit, including the management of the steam network in the refinery, can be found in our previous studies [28,72].
There is a possibility of supplying steam from the CHP unit to SC at all three main steam pressure levels, but an autonomous SC operation in terms of steam production and consumption was preferred in the past. Optimized SC energy management opens the possibility of importing steam from the CHP unit if it is economically attractive. Given the situation of LS excess in the refinery in the summer months, this would affect mainly the LS pressure level.

2.3. Energy and Environmental Assessment

2.3.1. Steam Cracker

Rerouting SS steam from the let-down station to the steam turbine increases the production of backpressure energy and, thus, reduces the needed condensing load. Analysis of the steam turbine´s steam consumption diagram and the steam expansion path in the enthalpy-entropy diagram of steam, according to the procedure proposed by Medica-Viola et al. (2020) [73], revealed the following:
  • Rerouting 4 t/h of SS steam from the let-down station to the steam turbine and letting it expand to the HS pressure level reduces steam flow to the turbine condenser by 1 t/h;
  • Heat rejection in the steam turbine condenser is reduced by 2.268 GJ/h per 1 t/h of steam flow to the condenser, considering the enthalpy of the discharge steam to the condenser of 2.438 GJ/t and that of the steam condensate leaving the condenser of 0.168 GJ/t.
The following data express the effect of fuel savings and the reduction of GHG emissions released from the SC boiler:
  • SS steam enthalpy leaving the SC steam boiler is 3.435 GJ/t and the difference between this value and that of steam condensate enthalpy leaving the turbine condenser has to be supplied by the fuel combusted in the boiler;
  • Thermal efficiency of the boiler resulting from certified measurements is 94.1%, based on the lower heating value of the combusted fuel (natural gas, NG);
  • The lower heating value of NG is 49 GJ/t and its emission factor is 2.75 tCO2/tNG.
Emissions of other GHG released from the SC boiler can be evaluated using the data in Table 3. Data were obtained from the automated monitoring system (AMS) of the SC.

2.3.2. Combined Heat and Power Plant

CHP serves as a marginal steam source and thus any change in the SC energy management patterns leading to steam import or export affects the CHP operation. According to our previous studies [28,72], the following data were adopted.
  • Specific MPR consumption is 0.09 t per ton of exported steam;
  • The lower heating value of MPR is 40.3 GJ/t and its emission factor is 3.2 tCO2/tMPR;
  • The average steam enthalpy imported to the SC from the CHP is 2.9 GJ/t;
  • Marginal backpressure electricity production in the CHP amounts to 150 kWh per ton of exported steam.
Emissions of other GHGs released from the CHP can be assessed using the data in Table 4 that were obtained from the refinery AMS.
The change in the backpressure electricity production in the CHP is associated with the change in the GHG emissions from electricity production elsewhere. To quantify this effect, the average energy mix of Slovenské Elektrárne, a.s., (Bratislava, Slovakia), the main electricity producer in Slovakia, was applied. The corresponding emission factors are presented in Table 5.

3. Results and Discussion

3.1. Energy Consumption

Table 6 provides key figures related to the change in fuel consumption in the SC after the installation of a smaller SS to HS let-down valve in 2019. As it results from Table 6, ethylene production remained almost constant during 2020 but the amount of SS steam let-down to HS decreased visibly. The first quarter of 2020 was affected by SC staff who were still learning how to fully exploit the potential offered by the smaller valve ‘B’. From the second quarter of 2020 onwards, the amount of SS steam let-down to HS was reduced by more than 75% compared to the average value shown in Table 2. The larger let-down valve ‘A’ is closed most of the time and the opening of valve ‘B’ is around or below 50%, indicating a functional SS steam let-down regulation. The associated decrease in NG consumption reached around 9000 GJ (180 t) in the first quarter of 2020 but increased to almost 29,000 GJ (580 t) in the next periods. The total estimated NG savings due to the decrease in the SS to HS steam let-down in 2020 compared to 2018 amounted to around 87 TJ (1778 t).
In addition to lower SS to HS steam let-down rate, the SC implemented changes in the energy management aimed at optimizing the fuel costs; i.e., increased import of steam from the refinery to reduce NG consumption in the SC boiler. The resulting impact on fuel consumption in both SC´s steam boiler and CHP´s steam boilers is shown in Figure 3. A comparison of NG energy consumed in the SC boiler in 2018 and 2020 yielded a decrease of more than 470 TJ. Its decomposition into individual contributions showed that, as presented in Table 6, 87 TJ are attributable to the decreased SS to HS let-down, which represents around 18% of the total change in NG consumption and an about 5% decrease in the total fuel consumption in the SC steam boiler at the same time. Additionally, SC steam import increased by 225 TJ in 2020 compared to 2018, which resulted in another decrease in NG consumption in the SC boiler by 270 TJ. This represents the largest contribution to the total NG consumption achieved. The remaining NG consumption decrease of 116 TJ (25% share in the total change in the NG consumption) was attributed to other investments and operational optimization activities performed during the SC turnaround in 2019. Ethylene production in 2018 and 2020 was almost the same, so it did not affect the changes observed in fuel consumption.
The increase in steam import from the refinery to the SC in 2020 compared to 2018 caused changes in the operation and load of the CHP (Figure 3). To cover the change in steam demand and condensing power production requirement, annual fuel energy consumption in CHP increased by more than 400 TJ between 2018 and 2020. Of this, 282 TJ (almost 70%) can be attributed to increased steam import to SC and the remaining 129 TJ (around 30%) represent other factors. It should be noted that the relative change in fuel energy consumption in the CHP is relatively small (around 4%) and the one attributable to the change in SC energy management is even smaller (less than 3%). Therefore, the effect of the change in SC steam import could be recognized in the CHP fuel balance only because of analogous steam consumption patterns in the refinery and comparable condensing power production in the CHP in 2018 and 2020.
Another interesting fact resulting from the data presented in Figure 3 is that the increase in steam import to SC did not result in a reduction in net fuel consumption. NG consumption in the SC steam boiler decreased by 270 TJ while that in the CHP steam boilers increased by 282 GJ. Thus, the import of steam from the refinery to the SC is a purely economic issue, which results from the 2020 NG price per GJ energy being by 20–40% higher than that of MPR fired in the CHP boilers. With a different fuel price constellation, the SC might start exporting steam to the refinery. In contrast, the installation of a smaller SS to HS let-down valves yielded net fuel energy savings localized in the SC. Therefore, this energy measure is feasible both from the economic and the energy point of view regardless of fuel cost. Moreover, there is neither negative nor positive synergy between these two measures, so that they can be exploited in parallel with a clearly distinguishable economic and energy effect.

3.2. GHG Emissions

The change in SC and CHP operation patterns resulting from the implemented SC energy management measures caused a change in GHG emissions. Figure 4 presents the resulting CO2 balance divided into individual items. The total annual change in CO2 emissions from the SC steam boiler resulting from the decrease in annual fuel energy consumption of 473 TJ (Figure 3) amounted to more than 26,500 t. Of this, almost 4900 t can be attributed to the decrease in SS to HS steam let-down and, since there is no change in CO2 emissions at the CHP, it represents the net CO2 balance of this measure for the refinery and SC complex at the same time. On the contrary, the increase in steam import to the SC resulted in a net increase in CO2 emissions for the refinery and SC complex of more than 7000 t, as the decrease in CO2 emissions of more than 15,000 t achieved in the SC was outbalanced by their increase by more than 22,000 t at the CHP. This finding further underlines that, while the achieved decrease of SS to HS steam let-down is beneficial from all considered viewpoints (economics, energy, environment), the increased steam import to the SC is only a matter of economics while its energetic end environmental impact is negative.
However, it must be remembered that the increase in CHP steam export caused by the increase in SC steam demand resulted in an increase in backpressure electricity production in the CHP which amounted to more than 11,000 MWh/year. Accepting the assumption that the refinery’s electricity consumption was not affected, an equivalent decrease in the purchase of electricity from the outside grid was achieved. This further led to a decrease in electricity production elsewhere. Applying the CO2 emission factor of the energy mix of Slovenské Elektrárne, a.s. (Bratislava, Slovakia), (Table 5), this translated into an almost 1600 t decrease in CO2 emissions outside of the refinery and SC complex. Thus, extending the control volume for the CO2 balance calculation to the entire Slovak republic yielded the resulting final change in CO2 emissions of over 5600 t/year. It can be concluded that even this CO2 balance disfavors the steam import to the SC from the refinery. An alternative approach, using marginal emission factors, is presented in Section 3.4.
Considering the CO2 balance effects of the SS steam let-down minimization and the increased steam import to the SC, a value below 1 kt/year was obtained (see Figure 4). This is a favorable result since the resulting combined effect of both actions is almost CO2 neutral while being economically attractive and leading to net fuel energy savings.
The balance of other major GHGs was also estimated using the same approach and the results are presented in Table 7. Given the low values of CO and SOx emission factors from SC steam boilers resulting from clean fuel combustion (NG) [74], the only notable reduction in emissions from SC is that of NOx. This amounts to more than 5 t/year in case of decreased SS to HS let-down and more than 15 t/year in case of steam import to the SC. On the other hand, there is a significant increase in SOx and NOx emissions from the CHP steam boilers, which results from an increase in the CHP load due to the import of steam to the SC amounting to more than 30 t/year regarding NOx emissions and more than 18 t/year regarding SOx emissions, respectively. This is caused by MPR fired in the CHP steam boilers being not clean fuel. The resulting emissions of sulfur oxides and nitrogen oxides are higher than those from NG combustion despite the renovation of the CHP in the past coupled with the commissioning of a flue gas desulfurization unit [75]. Even if the benefit of backpressure electricity production is incorporated in the calculations, emissions of both SOx and NOx increased by more than 13 t/year each; only those of CO decreased slightly. It can be concluded that while the reduction of SS to HS steam let-down led to a decrease in all considered GHGs, increased steam import to the SC led to their increase, except for the case of CO.
The given refinery is dedicated to transparency and committed to reducing the environmental impact of its operation. Like several other refineries and petrochemical enterprises, it publicly provides data on the GHGs and other emissions [76] and has implemented several investment projects to increase the energy efficiency and reduce the carbon footprint of both the SC [77] and the CHP [75] units. As a part of a business group, it actively participates in the long-term strategy of the company [78] to become a net-zero CO2 emitter. Energy management of the refinery and SC complex is expected to become a part of a larger optimization scheme that includes the entire business group, supporting the long-term goals of the strategy.

3.3. Economic Considerations

Though exact values are confidential, a rough economic evaluation of both measures together yields an annual cash flow of around 1 mil. € with approximately 70% of it resulting from decreased SS to HS let-down. This value already incorporates the CO2 effect. Considering the CO2 balance of both measures, an increase of CO2 price by 50 €/t (i.e., roughly doubling its summer 2021 price) would increase the cash flow of the decreased SS to HS let-down by almost 250,000 €/year, while that of the increased steam import to the SC would drop by over 350,000 €. Under such conditions, steam import to the SC is no longer beneficial unless the price difference between NG and MPR further increases. Though the observed and continuing trend of CO2 price increase is remarkable, its impact on the economic results is limited. A much higher effect on the project economics has the currently (October–November 2021) extremely high natural gas price which leads to the maximization of the steam import to the SC, despite the associated net increase in CO2 emissions.
The price difference between the NG and MPR price (in €/GJ) evolves dynamically; it increases nowadays as a result of the currently increasing NG prices worldwide. Despite the favorable actual situation, an opposite one has occurred several times in the past when the NG price dropped below that of the MPR. In such a case, the SC can export steam to the refinery at the HS pressure level. The technical issues associated with the operation of the HS steam network in the refinery were described in our previous study [28]. Additional steam from sources other than the CHP can be absorbed only occasionally and surplus HS steam let down to the MS pressure level. The effect of letting steam down from the HS to the MS pressure level has to be accounted for and it lowers the resulting benefit.

3.4. Discussion

As it results from Figure 3 and Figure 4, increasing the import to the SC from the refinery at the expense of own steam production is purely an economic driven measure. From a technical point of view, it can be considered an inter-fuel substitution [79]. The energy and environmental aspects of fuel substitution were studied by several researchers. Ditaranto et al. (2013) [80] explored the substitution of natural gas by hydrogen in fired heaters in a refinery using CFD simulation and experimental setup. They found that nitrogen oxides emission can be substantially reduced even if the whole hydrogen production chain was considered. Glushkov et al. (2020) [81] analyzed the switch of fuel from coal to composite fuel in a power plant to reduce greenhouse gas emissions, experimentally confirming significantly lower SOx and NOx emissions in the case of composite fuel combustion. Jou et al. (2010) [82] studied the possibility of recovering tail gas from several refining units and its use as a partial replacement of NG in refinery heaters, finding that, contrary to the significant reduction in CO2 emissions, the level of NOx increased modestly. Although the research presented suggests a transition to cleaner fuels as a viable means of reducing GHG emissions, a transition in the opposite way might still be acceptable for the industry if it is economically justified [38]. Moreover, as presented in Figure 4, there is a possible associated effect of the change in electricity production if fuel substitution is performed between two distinctive utility systems. Although both the SC and the CHP operate in the cogeneration mode, the SC produces mechanical power, while the CHP produces electricity. In such a case, the external emissions change should also be considered, as presented in Figure 4 and Table 7.
Emission factors from electricity production are known to vary significantly depending on the energy mix and other conditions considered in their evaluation [83,84]. As discussed in our recent study [85], the emission factor of CO2 can vary between close to zero values for an almost exclusively renewable energy-based mix up to 700 to 900 kg/MWh for coal- and oil-fired power plants. Adopting a value of 700 kg/MWh [86] instead of that from Table 5 (136 kg/MWh) substantially changes the resulting global CO2 balance of increased steam import into SC: global increase in CO2 emissions of 5600 t/year changes to the reduction of approximately 900 t/year. Similarly, much higher CO, NOx, and SOx emission factors were reported than those considered in this study (Table 5) for fossil fuel-fired power plants [87,88]. Their application in the GHG balance related to increased steam import to SC presented in Table 7 would lead to a net reduction of the emissions of all GHGs considered, although a net increase in both SOx and NOx emissions was observed for the refinery and SC control volume.
Calculation of the emissions of major GHGs and assessment of their reduction in the design phase or by revamp, renovation, and operation optimization of existing plants is a part of the environmental assessment of several studies. Often, emissions of all major pollutants considered are expressed in form of CO2 equivalent. Bamufleh et al. (2012) [68] and Luo et al. (2014) [89] applied this concept to assess the optimal layout of a cogeneration unit by means of multiobjective optimization. Alhajji and Demirel (2015) [69], Comodi et al. (2016) [90], and Berghout et al. (2019) [29] attempted to design and operation optimization of various refinery units and utility systems and used CO2 equivalent calculations as one of the decision criteria in the optimization process, considering either model emission factors provided by modeling software [69], extracted them from available literature [29] or used field data [90]. Garcia et al. (2014) [91], and Ifaei et al. (2019) [92], and Safder et al. (2019) [93] chose a different approach including the balance of GHG in a wider frame of an environmental assessment by calculating the Ecoindicator 99 values and using it as one of the optimization criteria. Although very useful for the optimization scope in general, either approach leads to desired results if applied to particular multi-source and multi-fuel systems such as in the present study. Therefore, individual emission factors are best obtained by analyzing field data. An example of such an approach is the study by Jou et al. (2010) [82] who experimentally investigated the effect of changing fuel composition on both CO2 and NOx emissions in a refinery furnace. Hadidi et al. (2016) [94] explored the mitigation options of GHG (CO2, NOx, SO2, and volatile organic compounds) in a Saudi Arabian refinery with both help of mathematical modeling and input from refinery experts. Li et al. (2019) [95] studied the environmental performance of a high-temperature heat pump-assisted gas separation plant located in China within a more complex frame of energy, exergy, economic and environmental optimization of the given plant, yielding achievable savings in CO2, NOx, and SO2 emissions. Finally, the authors themselves applied the balances of CO2, NOx, and SOx emissions based on fuel composition and field emissions data in their earlier studies on refinery processes [38] or oxygen production plant [85] optimization. It can be concluded that, while all mentioned approaches are viable, using available field data ensures the validity of the environmental assessment results both generally and in a particular on-site application.

4. Conclusions

Steam crackers (ethylene plants) represent extraordinary material- and energy-integrated chemical complexes with significant potential for multiobjective optimization. Efforts aimed at cutting down the energy consumption and related GHG emissions focus mainly on SC´s steam network and often propose decreasing the steam let-down rates as well as reducing mechanical power requirement provided by the steam turbines on-site. Another option to optimize energy consumption is the export or import at multiple pressure levels if the SC is integrated into a chemical or refining complex. The presented study analyzed both the internal SC´s steam management as well as the steam import/export options for an SC integrated into a refinery. The exploitation of the first measure represents direct savings of fuel energy and is thus advantageous from the energetic, economic, and environmental points of view. Steam flows between the SC and the refinery result only from economically driven inter-fuel substitution between the SC steam boiler and those in the CHP of the refinery and their energetic and environmental effect is questionable. Thus, a detailed analysis of the change in the main air pollutants (CO2, NOx, SOx, CO) was performed to define the final observed changes in GHG emissions into changes attributable to individual measures.
A study carried out in a mid-capacity ethylene production plant integrated into a refinery revealed the following: 1. Optimization of the SC’s internal steam management by the installation of a smaller SS steam let-down valve minimized steam reduction rates and led to direct NG savings in the SC´s steam boiler. At 87 TJ/year, this reduction represents 5% of the annual steam boiler´s fuel consumption. The associated reduction of GHG emissions reached almost 4900 t/year and more than 5 t/year in the case of CO2 and NOx, respectively, while the reduction of both SOx and CO emissions was negligible. The increase in the CO2 price affected the economics of this energy-saving measure beneficially. 2. Import of steam to the SC from the refinery due to lower fuel price used in the CHP boilers compared to that of NG, which led to an increase in the net consumption of fuel energy by 12 TJ/year. The reduction of CO2 emissions by more than 15,000 t/year and that of NOx emissions by more than 15 t/year due to decreased fuel consumption in the SC boiler was outbalanced by the increase in GHG emissions in the CHP in the following annual amounts: CO2: more than 22,000 t; NOx more than 30 t; SOx more than 18 t. Thus, a net increase in emissions was observed for all investigated pollutants except for CO where the final effect was very close to zero. This means that the increase in the price of carbon emissions negatively affected the economics of steam import to the SC from the refinery. Therefore, the sole driver for steam import to the SC remained only the price differential between MPR and NG; in case of a reverse price situation, steam export from the SC is possible but it would be associated with difficulties in the HS steam management network.
The increase in the associated backpressure electricity production in the CHP due to the increase in steam import to the SC led to a decrease in external emissions, depending on the fuel mix considered. For that of Slovenské elektrárne, a.s., (Bratislava, Slovakia), the decrease in the external emissions was insufficient to counteract the increase in the net emissions in the SC and refinery complex. If, however, electricity production in a fossil-fuel power plant was considered, the external emissions decrease would outbalance the net emissions increase in the SC and refinery complex.

Author Contributions

Conceptualization, M.V. and M.B.; methodology, K.H. and P.I.; software, P.F. and J.J.; validation, K.H. and P.I.; investigation, M.V. and M.B.; data curation, K.H. and P.F.; writing—original draft preparation, M.V.; writing—review and editing, M.B., P.I. and P.F.; visualization, P.F.; funding acquisition, J.J. All authors have read and agreed to the published version of the manuscript.

Funding

This study was supported by the Slovak Research and Development Agency under contract nos. APVV-18-0134 and APVV-19-0170 and by the Slovak Scientific Agency, grant no. VEGA 1/0511/21.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

All data obtained by calculations and analyses are listed directly in this study.

Conflicts of Interest

The authors declare no conflict of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.

References

  1. Rissman, J.; Bataille, C.; Masanet, E.; Aden, N.; Morrow, W.R.; Zhou, N.; Elliott, N.; Dell, R.; Heeren, N.; Huckestein, B.; et al. Technologies and policies to decarbonize global industry: Review and assessment of mitigation drivers through 2070. Appl. Energy 2020, 266, 114848. [Google Scholar] [CrossRef]
  2. Gharaie, M.; Panjeshahi, M.H.; Kim, J.-K.; Jobson, M.; Smith, R. Retrofit strategy for the site-wide mitigation of CO2 emissions in the process industries. Chem. Eng. Res. Des. 2015, 94, 213–241. [Google Scholar] [CrossRef]
  3. Rehfeldt, M.; Worrell, E.; Eichhammer, W.; Fleiter, T. A review of the emission reduction potential of fuel switch towards biomass and electricity in European basic materials industry until 2030. Renew. Sustain. Energy Rev. 2020, 120, 109672. [Google Scholar] [CrossRef]
  4. Borozan, D. Decomposing the changes in European final energy consumption. Energy Strategy Rev. 2018, 22, 26–36. [Google Scholar] [CrossRef]
  5. Gerres, T.; Ávila, J.P.C.; Llamas, P.L.; San Román, T.G. A review of cross-sector decarbonisation potentials in the European energy intensive industry. J. Clean. Prod. 2019, 210, 585–601. [Google Scholar] [CrossRef]
  6. Bungener, S.L.; Van Eetvelde, G.; Maréchal, F. Optimal Operations and Resilient Investments in Steam Networks. Front. Energy Res. 2016, 4, 1. [Google Scholar] [CrossRef] [Green Version]
  7. Liu, R.; He, F.; Chen, L. Can Energy Management Systems Improve the Performance of Industrial Enterprises? Pol. J. Environ. Stud. 2021, 30, 5133–5147. [Google Scholar] [CrossRef]
  8. Kubule, A.; Ločmelis, K.; Blumberga, D. Analysis of the results of national energy audit program in Latvia. Energy 2020, 202, 117679. [Google Scholar] [CrossRef]
  9. de Magalhães, R.F.; Danilevicz, Â.d.M.F.; Palazzo, J. Managing trade-offs in complex scenarios: A decision-making tool for sustainability projects. J. Clean. Prod. 2019, 212, 447–460. [Google Scholar] [CrossRef]
  10. Maciková, L.; Smorada, M.; Dorčák, P.; Beug, B.; Markovič, P. Financial Aspects of Sustainability: An Evidence from Slovak Companies. Sustainability 2018, 10, 2274. [Google Scholar] [CrossRef] [Green Version]
  11. Drobyazko, S.; Skrypnyk, M.; Radionova, N.; Hryhorevska, O.; Matiukha, M. Enterprise energy supply system design management based on renewable energy sources. Glob. J. Environ. Sci. Manag. 2021, 7, 369–382. [Google Scholar] [CrossRef]
  12. Kar, Y. Catalytic cracking of pyrolytic oil by using bentonite clay for green liquid hydrocarbon fuels production. Biomass Bioenergy 2018, 119, 473–479. [Google Scholar] [CrossRef]
  13. Ciesielska-Maciągowska, D.; Klimczak, D.; Skrzek-Lubasińska, M. Central and Eastern European CO2 Market—Challenges of Emissions Trading for Energy Companies. Energies 2021, 14, 1051. [Google Scholar] [CrossRef]
  14. Jiang, C.; Yue, Y. Sensitivity Analysis of Key Factors Influencing Carbon Prices under the EU ETS. Pol. J. Environ. Stud. 2021, 30, 3645–3658. [Google Scholar] [CrossRef]
  15. Locmelis, K.; Blumberga, D.; Blumberga, A.; Kubule, A. Benchmarking of Industrial Energy Efficiency. Outcomes of an Energy Audit Policy Program. Energies 2020, 13, 2210. [Google Scholar] [CrossRef]
  16. Malega, P.; Majerník, M.; Rudy, V.; Daneshjo, N. Innovation Support and Eco-Innovations in the Slovak Republic in the Intentions of Sustainable Development. Pol. J. Environ. Stud. 2021, 30, 3753–3768. [Google Scholar] [CrossRef]
  17. Glavič, P.; Pintarič, Z.N.; Bogataj, M. Process Design and Sustainable Development—A European Perspective. Processes 2021, 9, 148. [Google Scholar] [CrossRef]
  18. Locmelis, K.; Blumberga, D.; Bariss, U. Energy efficiency in large industrial plants. Legislative aspects. Energy Procedia 2018, 147, 202–206. [Google Scholar] [CrossRef]
  19. Rehfeldt, M.; Globisch, J.; Fleiter, T. Fuel choice in industrial steam generation: Empirical evidence reveals technology preferences. Energy Strategy Rev. 2019, 26, 100407. [Google Scholar] [CrossRef]
  20. Martins, F.; Felgueiras, C.; Smitkova, M.; Caetano, N. Analysis of Fossil Fuel Energy Consumption and Environmental Impacts in European Countries. Energies 2019, 12, 964. [Google Scholar] [CrossRef] [Green Version]
  21. Wang, R.Q.; Jiang, L.; Wang, Y.D.; Roskilly, A.P. Energy saving technologies and mass-thermal network optimization for decarbonized iron and steel industry: A review. J. Clean. Prod. 2020, 274, 122997. [Google Scholar] [CrossRef]
  22. Peng, Z.; Fu, C.; Zhu, K.; Zhang, Q.; Ni, D.; Yang, S. An improved LP model for energy optimization of the integrated iron and steel plant with a cogeneration system in China. J. Syst. Sci. Syst. Eng. 2016, 25, 515–534. [Google Scholar] [CrossRef]
  23. Griffin, P.W.; Hammond, G.P.; Norman, J.B. Industrial decarbonisation of the pulp and paper sector: A UK perspective. Appl. Therm. Eng. 2018, 134, 152–162. [Google Scholar] [CrossRef]
  24. Gambini, M.; Vellini, M.; Stilo, T.; Manno, M.; Bellocchi, S. High-Efficiency Cogeneration Systems: The Case of the Paper Industry in Italy. Energies 2019, 12, 335. [Google Scholar] [CrossRef] [Green Version]
  25. Vooradi, R.; Anne, S.B.; Tula, A.K.; Eden, M.R.; Gani, R. Energy and CO2 management for chemical and related industries: Issues, opportunities and challenges. BMC Chem. Eng. 2019, 1, 7. [Google Scholar] [CrossRef]
  26. Ahmadi, G.; Toghraie, D.; Akbari, O. Energy, exergy and environmental (3E) analysis of the existing CHP system in a petrochemical plant. Renew. Sustain. Energy Rev. 2019, 99, 234–242. [Google Scholar] [CrossRef]
  27. Morandin, M.; Hackl, R.; Harvey, S. Economic feasibility of district heating delivery from industrial excess heat: A case study of a Swedish petrochemical cluster. Energy 2014, 65, 209–220. [Google Scholar] [CrossRef]
  28. Hanus, K.; Variny, M.; Illés, P. Assessment and Prediction of Complex Industrial Steam Network Operation by Combined Thermo-Hydrodynamic Modeling. Processes 2020, 8, 622. [Google Scholar] [CrossRef]
  29. Berghout, N.; Meerman, H.; van den Broek, M.; Faaij, A. Assessing deployment pathways for greenhouse gas emissions reductions in an industrial plant—A case study for a complex oil refinery. Appl. Energy 2019, 236, 354–378. [Google Scholar] [CrossRef] [Green Version]
  30. Bütün, H.; Kantor, I.; Maréchal, F. Incorporating Location Aspects in Process Integration Methodology. Energies 2019, 12, 3338. [Google Scholar] [CrossRef] [Green Version]
  31. Chen, C.-L.; Lin, C.-Y. A flexible structural and operational design of steam systems. Appl. Therm. Eng. 2011, 31, 2084–2093. [Google Scholar] [CrossRef]
  32. Del Nogal, F.L.; Kim, J.K.; Perry, S.; Smith, R. Synthesis of Mechanical Driver and Power Generation Configurations, Part 1: Optimization Framework. AIChE J. 2010, 56, 2356–2376. [Google Scholar] [CrossRef]
  33. Zhao, L.; Zhong, W.; Du, W. Data-Driven Robust Optimization for Steam Systems in Ethylene Plants under Uncertainty. Processes 2019, 7, 744. [Google Scholar] [CrossRef] [Green Version]
  34. Svensson, E.; Morandin, M.; Harvey, S.; Papadokonstantakis, S. Studying the Role of System Aggregation in Energy Targeting: A Case Study of a Swedish Oil Refinery. Energies 2020, 13, 958. [Google Scholar] [CrossRef] [Green Version]
  35. Hassiba, R.J.; Linke, P. On the simultaneous integration of heat and carbon dioxide in industrial parks. Appl. Therm. Eng. 2017, 127, 81–94. [Google Scholar] [CrossRef]
  36. Ma, Y.; Wang, S.; Wang, K.; Liu, L.; Zhang, R. Co-benefits analysis of energy cascade utilization in an industrial park in China. Environ. Sci. Pollut. Res. 2019, 26, 16181–16194. [Google Scholar] [CrossRef]
  37. Zhu, Q.; Luo, X.; Zhang, B.; Chen, Y.; Mo, S. Mathematical modeling, validation, and operation optimization of an industrial complex steam turbine network-methodology and application. Energy 2016, 97, 191–213. [Google Scholar] [CrossRef]
  38. Variny, M.; Jediná, D.; Kizek, J.; Illés, P.; Lukáč, L.; Janošovský, J.; Lesný, M. An Investigation of the Techno-Economic and Environmental Aspects of Process Heat Source Change in a Refinery. Processes 2019, 7, 776. [Google Scholar] [CrossRef] [Green Version]
  39. Marton, S.; Svensson, E.; Subiaco, R.; Bengtsson, F.; Harvey, S. A Steam Utility Network Model for the Evaluation of Heat Integration Retrofits—A Case Study of an Oil Refinery. J. Sustain. Dev. Energy Water Environ. Syst. 2017, 5, 560–578. [Google Scholar] [CrossRef] [Green Version]
  40. Nguyen, T.Q.; Slawnwhite, J.D.; Boulama, K.G. Power generation from residual industrial heat. Energy Convers. Manag. 2010, 51, 2220–2229. [Google Scholar] [CrossRef]
  41. Li, Z.; Zhao, L.; Du, W.; Qian, F. Modeling and Optimization of the Steam Turbine Network of an Ethylene Plant. Chin. J. Chem. Eng. 2013, 21, 520–528. [Google Scholar] [CrossRef]
  42. Verhees, P.; Amghizar, I.; Goemare, J.; Akhras, A.R.; Marin, G.B.; Van Geem, K.M.; Heynderickx, G.J. 1D Model for Coupled Simulation of Steam Cracker Convection Section with Improved Evaporation Model. Chem. Ing. Tech. 2016, 88, 1650–1664. [Google Scholar] [CrossRef]
  43. Hackl, R.; Harvey, S. Applying exergy and total site analysis for targeting refrigeration shaft power in industrial clusters. Energy 2013, 55, 5–14. [Google Scholar] [CrossRef] [Green Version]
  44. Zhao, L.; Ning, C.; You, F. Operational optimization of industrial steam systems under uncertainty using data- Driven adaptive robust optimization. AIChE J. 2019, 65, e16500. [Google Scholar] [CrossRef]
  45. Li, Z.; Du, W.; Zhao, L.; Qian, F. Modeling and Optimization of a Steam System in a Chemical Plant Containing Multiple Direct Drive Steam Turbines. Ind. Eng. Chem. Res. 2014, 53, 11021–11032. [Google Scholar] [CrossRef]
  46. Zhao, H.; Ierapetritou, M.G.; Shah, N.K.; Rong, G. Integrated model of refining and petrochemical plant for enterprise-wide optimization. Comput. Chem. Eng. 2017, 97, 194–207. [Google Scholar] [CrossRef]
  47. Ketabchi, E.; Mechleri, E.; Arellano-Garcia, H. Increasing operational efficiency through the integration of an oil refinery and an ethylene production plant. Chem. Eng. Res. Des. 2019, 152, 85–94. [Google Scholar] [CrossRef]
  48. Mrzljak, V.; Poljak, I.; Mrakovčić, T. Energy and exergy analysis of the turbo-generators and steam turbine for the main feed water pump drive on LNG carrier. Energy Convers. Manag. 2017, 140, 307–323. [Google Scholar] [CrossRef]
  49. Weickgenannt, A.; Kantor, I.; Maréchal, F.; Schiffmann, J. On the Application of Small-Scale Turbines in Industrial Steam Networks. Energies 2021, 14, 3149. [Google Scholar] [CrossRef]
  50. Ren, X.-Y.; Jia, X.-X.; Varbanov, P.S.; Klemeš, J.J.; Liu, Z.-Y. Targeting the cogeneration potential for Total Site utility systems. J. Clean. Prod. 2018, 170, 625–635. [Google Scholar] [CrossRef]
  51. Murugan, S.; Horák, B. Tri and polygeneration systems—A review. Renew. Sustain. Energy Rev. 2016, 60, 1032–1051. [Google Scholar] [CrossRef]
  52. Ng, K.S.; Hernandez, E.M. A systematic framework for energetic, environmental and economic (3E) assessment and design of polygeneration systems. Chem. Eng. Res. Des. 2016, 106, 1–25. [Google Scholar] [CrossRef] [Green Version]
  53. Dai, M.; Yang, F.; Zhang, Z.; Liu, G.; Feng, X. Energetic, economic and environmental (3E) multi-objective optimization of the back-end separation of ethylene plant based on adaptive surrogate model. J. Clean. Prod. 2021, 310, 127426. [Google Scholar] [CrossRef]
  54. Nabavi, S.R.; Rangaiah, G.P.; Niaei, A.; Salari, D. Multiobjective Optimization of an Industrial LPG Thermal Cracker using a First Principles Model. Ind. Eng. Chem. Res. 2009, 48, 9523–9533. [Google Scholar] [CrossRef]
  55. Deng, C.; Zhou, Y.; Jiang, W.; Feng, X. Optimal design of inter-plant hydrogen network with purification reuse/recycle. Int. J. Hydrogen Energy 2017, 42, 19984–20002. [Google Scholar] [CrossRef]
  56. Kamrava, S.; Gabriel, K.J.; El-Halwagi, M.M.; Eljack, F.T. Managing abnormal operation through process integration and cogeneration systems. Clean Technol. Environ. Policy 2014, 17, 119–128. [Google Scholar] [CrossRef]
  57. Gong, S.; Shao, C.; Zhu, L. An energy efficiency integration optimization scheme for ethylene production with respect to multiple working conditions. Energy 2019, 182, 280–295. [Google Scholar] [CrossRef]
  58. Shen, F.; Wang, X.; Huang, L.; Ye, Z.; Qian, F. Modeling and Optimization of a Large-Scale Ethylene Plant Energy System with Energy Structure Analysis and Management. Ind. Eng. Chem. Res. 2019, 58, 1686–1700. [Google Scholar] [CrossRef]
  59. Geng, Z.; Zhang, Y.; Li, C.; Han, Y.; Cui, Y.; Yu, B. Energy optimization and prediction modeling of petrochemical industries: An improved convolutional neural network based on cross-feature. Energy 2020, 194, 116851. [Google Scholar] [CrossRef]
  60. Shen, F.; Wang, M.; Huang, L.; Qian, F. Exergy analysis and multi-objective optimisation for energy system: A case study of a separation process in ethylene manufacturing. J. Ind. Eng. Chem. 2021, 93, 394–406. [Google Scholar] [CrossRef]
  61. Wang, J.; He, Y.-L.; Zhu, Q.-X. Energy and Production Efficiency Optimization of an Ethylene Plant Considering Process Operation and Structure. Ind. Eng. Chem. Res. 2020, 59, 1202–1217. [Google Scholar] [CrossRef]
  62. Chen, K.; Liu, S.; Han, Y.; Zhang, Y.; Geng, Z.; Liu, L.; Peng, T.; Ding, Y. Energy efficiency assessment and resource optimization using novel DEA model: Evidence from complex chemical processes. Energy Effic. 2020, 13, 1427–1439. [Google Scholar] [CrossRef]
  63. Sanaye, S.; Khakpaay, N.; Chitsaz, A. Thermo-economic and environmental multi-objective optimization of a novel arranged biomass-fueled gas engine and backpressure steam turbine combined system for pulp and paper mills. Sustain. Energy Technol. Assess. 2020, 40, 100778. [Google Scholar] [CrossRef]
  64. Ziółkowski, P.; Kowalczyk, T.; Lemański, M.; Badur, J. On energy, exergy, and environmental aspects of a combined gas-steam cycle for heat and power generation undergoing a process of retrofitting by steam injection. Energy Convers. Manag. 2019, 192, 374–384. [Google Scholar] [CrossRef]
  65. Pintarič, Z.N.; Varbanov, P.S.; Klemeš, J.J.; Kravanja, Z. Multi-objective multi-period synthesis of energy efficient processes under variable environmental taxes. Energy 2019, 189, 116182. [Google Scholar] [CrossRef]
  66. Ahmadi, G.; Toghraie, D.; Akbari, O.A. Technical and environmental analysis of repowering the existing CHP system in a petrochemical plant: A case study. Energy 2018, 159, 937–949. [Google Scholar] [CrossRef]
  67. Rimar, M.; Kulikova, O.; Kulikov, A.; Fedak, M. Energy Treatment of Solid Municipal Waste in Combination with Biomass by Decentralized Method with the Respect to the Negative Effects on the Environment. Sustainability 2021, 13, 4405. [Google Scholar] [CrossRef]
  68. Bamufleh, H.S.; Ponce-Ortega, J.M.; El-Halwagi, M.M. Multi-objective optimization of process cogeneration systems with economic, environmental, and social tradeoffs. Clean Technol. Environ. Policy 2012, 15, 185–197. [Google Scholar] [CrossRef]
  69. Alhajji, M.; Demirel, Y. Energy and environmental sustainability assessment of a crude oil refinery by thermodynamic analysis. Int. J. Energy Res. 2015, 39, 1925–1941. [Google Scholar] [CrossRef]
  70. Carmo-Calado, L.; Hermoso-Orzáez, M.J.; Mota-Panizio, R.; Guilherme-Garcia, B.; Brito, P. Co-Combustion of Waste Tires and Plastic-Rubber Wastes with Biomass Technical and Environmental Analysis. Sustainability 2020, 12, 1036. [Google Scholar] [CrossRef] [Green Version]
  71. Constantin, D.E.; Bocaneala, C.; Voiculescu, M.; Rosu, A.; Merlaud, A.; Van Roozendael, M.; Georgescu, P.L. Evolution of SO2 and NOx Emissions from Several Large Combustion Plants in Europe during 2005–2015. Int. J. Environ. Res. Public Health 2020, 17, 3630. [Google Scholar] [CrossRef]
  72. Variny, M.; Blahušiak, M.; Mierka, O.; Godó, Š.; Margetíny, T. Energy saving measures from their cradle to full adoption with verified, monitored, and targeted performance: A look back at energy audit at Catalytic Naphtha Reforming Unit (CCR). Energy Effic. 2019, 12, 1771–1793. [Google Scholar] [CrossRef]
  73. Medica-Viola, V.; Šegota, S.B.; Mrzljak, V.; Štifanić, D. Comparison of conventional and heat balance based energy analyses of steam turbine. Pomorstvo 2020, 34, 74–85. [Google Scholar] [CrossRef]
  74. Mac Kinnon, M.A.; Brouwer, J.; Samuelsen, S. The role of natural gas and its infrastructure in mitigating greenhouse gas emissions, improving regional air quality, and renewable resource integration. Prog. Energy Combust. Sci. 2018, 64, 62–92. [Google Scholar] [CrossRef]
  75. Mach, V. EDISON Rekonstrukce a Modernizace Teplárny v Areálu SLOVNAFT, a.s. Available online: http://old.allforpower.cz/UserFiles/files/2011/mach.pdf (accessed on 28 June 2021). (In Slovak).
  76. SLOVNAFT, a.s. Sustainable Development Commitment—Environment. Available online: https://slovnaft.sk/sk/o-nas/trvalo-udrzatelny-rozvoj/zivotne-prostredie/ (accessed on 12 October 2021). (In Slovak).
  77. SLOVNAFT, a.s. Recently Realized Investment and Modernization Actions. Available online: https://slovnaft.sk/sk/o-nas/informacie-o-investiciach/modernizacia-etylenovej-jednotky-a-vystavba-ldpe-4/ (accessed on 12 October 2021). (In Slovak).
  78. MOL Group Strategy 2030. Available online: https://molgroup.info/en/strategy-2030 (accessed on 28 September 2021).
  79. Rehfeldt, M.; Fleiter, T.; Worrell, E. Inter-fuel substitution in European industry: A random utility approach on industrial heat demand. J. Clean. Prod. 2018, 187, 98–110. [Google Scholar] [CrossRef]
  80. Ditaranto, M.; Anantharaman, R.; Weydahl, T. Performance and NOx Emissions of Refinery Fired Heaters Retrofitted to Hydrogen Combustion. Energy Procedia 2013, 37, 7214–7220. [Google Scholar] [CrossRef] [Green Version]
  81. Glushkov, D.; Kuznetsov, G.; Paushkina, K. Switching Coal-Fired Thermal Power Plant to Composite Fuel for Recovering Industrial and Municipal Waste: Combustion Characteristics, Emissions, and Economic Effect. Energies 2020, 13, 259. [Google Scholar] [CrossRef] [Green Version]
  82. Jou, C.-J.G.; Wu, C.-R.; Lee, C.-L. Reduction of energy cost and CO2 emission for the furnace using energy recovered from waste tail-gas. Energy 2010, 35, 1232–1236. [Google Scholar] [CrossRef]
  83. Seckinger, N.; Radgen, P. Dynamic Prospective Average and Marginal GHG Emission Factors—Scenario-Based Method for the German Power System until 2050. Energies 2021, 14, 2527. [Google Scholar] [CrossRef]
  84. Smith, C.N.; Hittinger, E. Using marginal emission factors to improve estimates of emission benefits from appliance efficiency upgrades. Energy Effic. 2019, 12, 585–600. [Google Scholar] [CrossRef]
  85. Variny, M.; Jediná, D.; Rimár, M.; Kizek, J.; Kšiňanová, M. Cutting Oxygen Production-Related Greenhouse Gas Emissions by Improved Compression Heat Management in a Cryogenic Air Separation Unit. Int. J. Environ. Res. Public Health 2021, 18, 10370. [Google Scholar] [CrossRef]
  86. Hamels, S. CO2 Intensities and Primary Energy Factors in the Future European Electricity System. Energies 2021, 14, 2165. [Google Scholar] [CrossRef]
  87. Campbell, P.E.; McMullan, J.T.; Williams, B.C. Concept for a competitive coal fired integrated gasification combined cycle power plant. Fuel 2000, 79, 1031–1040. [Google Scholar] [CrossRef]
  88. Strachan, N.; Farrell, A. Emissions from distributed vs. centralized generation: The importance of system performance. Energy Policy 2006, 34, 2677–2689. [Google Scholar] [CrossRef]
  89. Luo, X.; Hu, J.; Zhao, J.; Zhang, B.; Chen, Y.; Mo, S. Multi-objective optimization for the design and synthesis of utility systems with emission abatement technology concerns. Appl. Energy 2014, 136, 1110–1131. [Google Scholar] [CrossRef]
  90. Comodi, G.; Renzi, M.; Rossi, M. Energy efficiency improvement in oil refineries through flare gas recovery technique to meet the emission trading targets. Energy 2016, 109, 1–12. [Google Scholar] [CrossRef]
  91. García, N.; Fernández-Torres, M.J.; Caballero, J.A. Simultaneous environmental and economic process synthesis of isobutane alkylation. J. Clean. Prod. 2014, 81, 270–280. [Google Scholar] [CrossRef] [Green Version]
  92. Ifaei, P.; Safder, U.; Yoo, C. Multi-scale smart management of integrated energy systems, Part 1: Energy, economic, environmental, exergy, risk (4ER) and water-exergy nexus analyses. Energy Convers. Manag. 2019, 197, 111851. [Google Scholar] [CrossRef]
  93. Safder, U.; Ifaei, P.; Yoo, C. Multi-scale smart management of integrated energy systems, Part 2: Weighted multi-objective optimization, multi-criteria decision making, and multi-scale management (3M) methodology. Energy Convers. Manag. 2019, 198, 111830. [Google Scholar] [CrossRef]
  94. Hadidi, L.A.; AlDosary, A.S.; Al-Matar, A.K.; Mudallah, O.A. An optimization model to improve gas emission mitigation in oil refineries. J. Clean. Prod. 2016, 118, 29–36. [Google Scholar] [CrossRef]
  95. Li, X.; Zhang, Y.; Fang, L.; Jin, Z.; Zhang, Y.; Yu, X.; Ma, X.; Deng, N.; Wu, Z. Energy, exergy, economic, and environmental analysis of an integrated system of high-temperature heat pump and gas separation unit. Energy Convers. Manag. 2019, 198, 111911. [Google Scholar] [CrossRef]
Figure 1. Simplified block scheme of the steam cracker´s (SC) steam network. HS—high-pressure steam, LS—low-pressure steam, MS—intermediate pressure steam, SS—superhigh pressure steam.
Figure 1. Simplified block scheme of the steam cracker´s (SC) steam network. HS—high-pressure steam, LS—low-pressure steam, MS—intermediate pressure steam, SS—superhigh pressure steam.
Ijerph 18 12267 g001
Figure 2. Annual SS steam production and consumption. MTPA—million tons per annum.
Figure 2. Annual SS steam production and consumption. MTPA—million tons per annum.
Ijerph 18 12267 g002
Figure 3. Comparison of fuel energy consumption in the SC’s steam boiler and the CHP’s (combined heat and power unit) steam boilers in 2018 and 2020.
Figure 3. Comparison of fuel energy consumption in the SC’s steam boiler and the CHP’s (combined heat and power unit) steam boilers in 2018 and 2020.
Ijerph 18 12267 g003
Figure 4. Effect of implemented energy management optimization on CO2 emissions balance change (2020 vs. 2018).
Figure 4. Effect of implemented energy management optimization on CO2 emissions balance change (2020 vs. 2018).
Ijerph 18 12267 g004
Table 1. Annual SS steam production and consumption, and ethylene production. HS—high-pressure steam, SS—superhigh pressure steam.
Table 1. Annual SS steam production and consumption, and ethylene production. HS—high-pressure steam, SS—superhigh pressure steam.
YearSpecific Ethylene Production (% of Design Capacity)SS Steam Consumption (t/% of Specific Ethylene Production)
20156818,795
20167317,849
20178815,102
201810016,460
20198517,429
Table 2. Steam let-down rate and valve opening before steam cracker (SC) turnaround in 2019; I to XII—January to December.
Table 2. Steam let-down rate and valve opening before steam cracker (SC) turnaround in 2019; I to XII—January to December.
Time PeriodSpecific Ethylene Production
(% of Quarterly Design Capacity)
SS Steam Let-Down to HS (t)Let-Down Valve ‘A’ Opening (%)
2018 X to XII9455,26415.10
2019 I to III9363,99013.68
2019 IV to VI10678,92414.19
2019 VII to IX11075,03713.78
Quarterly average 68,304
Table 3. Key GHGs (greenhouse gases) emissions data with respect to steam cracker (SC) auxiliary steam boiler.
Table 3. Key GHGs (greenhouse gases) emissions data with respect to steam cracker (SC) auxiliary steam boiler.
Fuel Energy Consumed in 20181647 TJ
PollutantEmissions in 2018 (t)Emission Factor (kg/TJ)
SOx0.130.08
NOx94.8457.58
CO1.7871.09
Table 4. Key GHGs emissions data on combined heat and power plant (CHP) steam boilers.
Table 4. Key GHGs emissions data on combined heat and power plant (CHP) steam boilers.
Fuel Energy Consumed in 201810,773 TJ
PollutantEmissions in 2018 (t) 1Emission Factor (kg/TJ)
SOx705.5565.50
NOx1165.03108.14
CO10.280.95
1 t = tons.
Table 5. Average emission factors of power produced by Slovenské Elektrárne, a.s., adapted from [38].
Table 5. Average emission factors of power produced by Slovenské Elektrárne, a.s., adapted from [38].
PollutantCO2SOxNOxCO
Emission factor (kg/MWh)1360.3920.1070.061
Table 6. Key process features and natural gas consumption decrease achieved by the installation and use of valve ‘B’.
Table 6. Key process features and natural gas consumption decrease achieved by the installation and use of valve ‘B’.
Time PeriodSpecific Ethylene Production (% of Quarterly Design Capacity)SS Steam Let-Down to HS (t) 1SS to HS Steam Let-Down Valves Opening (%)NG Consumption Decrease * (GJ)NG Consumption Decrease * (t)
Valve ‘A’Valve ‘B’
2020 I to III10847,3261.5869.518808179.8
2020 IV to VI10615,1360.0146.3128,198575.5
2020 VII to IX10314,4900.0049.5628,587583.4
2020 X to XII9926,2550.6852.0121,500438.8
2020 total87,0941777.5
1 t = tons. * Compared to the average of 2018. NG—natural gas.
Table 7. Effect of implemented energy management optimization on the balance of other GHGs (2020 vs. 2018).
Table 7. Effect of implemented energy management optimization on the balance of other GHGs (2020 vs. 2018).
PollutantCONOxSOx
Effect of decreased SS to HS steam reduction, total (t) 1−0.10−5.02−0.01
Effect of increased steam export to the SC, total (t), out of which−0.0214.9518.45
Change in GHG emissions from the SC steam boiler (t)−0.29−15.54−0.02
Change in GHG emissions from the CHP steam boilers (t)0.2730.4918.47
Change in GHG emissions outside the refinery due to the increased steam export to the SC (t)−0.71−1.25−4.57
Global change in GHG emissions due to the increased steam export to the SC (t)−0.7313.7013.88
1 t = tons.
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Variny, M.; Hanus, K.; Blahušiak, M.; Furda, P.; Illés, P.; Janošovský, J. Energy and Environmental Assessment of Steam Management Optimization in an Ethylene Plant. Int. J. Environ. Res. Public Health 2021, 18, 12267. https://doi.org/10.3390/ijerph182212267

AMA Style

Variny M, Hanus K, Blahušiak M, Furda P, Illés P, Janošovský J. Energy and Environmental Assessment of Steam Management Optimization in an Ethylene Plant. International Journal of Environmental Research and Public Health. 2021; 18(22):12267. https://doi.org/10.3390/ijerph182212267

Chicago/Turabian Style

Variny, Miroslav, Kristián Hanus, Marek Blahušiak, Patrik Furda, Peter Illés, and Ján Janošovský. 2021. "Energy and Environmental Assessment of Steam Management Optimization in an Ethylene Plant" International Journal of Environmental Research and Public Health 18, no. 22: 12267. https://doi.org/10.3390/ijerph182212267

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop