Next Article in Journal
Endo-Exoglucanase Synergism for Cellulose Nanofibril Production Assessment and Characterization
Previous Article in Journal
Potent Inhibitory Activity of Natural Product Anaephene B and Analogues against Leishmania tarentolae In Vitro
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Molecules
Volume 28
Issue 3
10.3390/molecules28030949
molecules-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Modified Technogenic Asphaltenes as Enhancers of the Thermal Conductivity of Paraffin

by
Svetlana N. Gorbacheva
1,2,
Yulia Yu. Borisova
3,
Veronika V. Makarova
1,2,
Sergey V. Antonov
1,2,
Dmitry N. Borisov
3 and
Makhmut R. Yakubov
3,*
1
Institute of Macromolecular Compounds, Russian Academy of Sciences, Bolshoi Prospect V.O. 31, 199004 St. Petersburg, Russia
2
A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, Leninsky Pr. 29, 119991 Moscow, Russia
3
Arbuzov Institute of Organic and Physical Chemistry, FRC Kazan Scientific Center, Russian Academy of Sciences, Arbuzov Str. 8, 420088 Kazan, Russia
*
Author to whom correspondence should be addressed.
Molecules 2023, 28(3), 949; https://doi.org/10.3390/molecules28030949
Submission received: 16 November 2022 / Revised: 15 January 2023 / Accepted: 16 January 2023 / Published: 18 January 2023
(This article belongs to the Section Applied Chemistry)
Browse Figures
Review Reports Versions Notes

Abstract

:
The low thermal conductivity of paraffin and other organic phase change materials limits their use in thermal energy storage devices. The introduction of components with a high thermal conductivity such as graphene into these materials leads to an increase in their thermal conductivity. In this work, we studied the use of inexpensive carbon fillers containing a polycyclic aromatic core, due to them having a structural similarity with graphene, to increase the thermal conductivity of paraffin. As such fillers, technogenic asphaltenes isolated from ethylene tar and their modified derivatives were used. It is shown that the optimal concentration of carbon fillers in the paraffin composite, which contributes to the formation of a structural framework and resistance to sedimentation, is 5 and 30 wt. %, while intermediate concentrations are ineffective, apparently due to the formation of large aggregates, the concentration of which is insufficient to form a strong framework. It has been found that the addition of asphaltenes modified with ammonium persulfate in acetic acid significantly increases the thermal conductivity of paraffin by up to 72%.

1. Introduction

It is known that organic phase change materials (PCM) are capable of accumulating and releasing heat due to phase transitions and can be used to accumulate thermal energy [1]. Paraffin-based systems are widely used as such devices, since they have a high energy storage density; they are also characterized by high thermal and chemical stability, they are non-toxic, and also have a low cost [2]. The disadvantage of such systems is the low rate of heat transfer, which leads to a decrease in the performance of heat accumulators and restricts their use [3]. The introduction of substances with a high thermal conductivity, such as graphene, into these systems improves the thermal properties of PCMs. Among them, metals [4], metal oxides [5], and boron nitride [6,7] could be mentioned. Carbon-based substances, such as graphene, are among the most popular additives due to their relatively high thermal conductivity [8,9,10]. In this case, an effective increase in the thermal conductivity of PCMs is associated with the presence of the π–π interaction between planar polycyclic fragments, which promotes heat transfer [11,12,13].
Although paraffin-based PCMs containing graphene particles or carbon nanotubes exhibit higher thermal conductivity enhancement [14,15], the high cost of these carbon nanofillers restricts their application [16]. On the other hand, carbon black and graphite are much cheaper and can be used to enhance the thermal conductivity of PCMs. Wu et al. [17] reported an increase in thermal conductivity in octadecane containing carbon black nanopowder modified with oleic acid. An improvement in the thermal conductivity of paraffin wax filled with expanded flexible graphite with different densities was shown in [18]. However, in most cases, inexpensive carbon materials require pretreatment and modification to be used as PCM thermal conductivity enhancers.
Glova et al. [19], using computer simulations, have shown that other inexpensive carbon substances, petroleum asphaltenes, can increase the thermal conductivity of liquid paraffin, provided that peripheral alkane groups are removed from the polyaromatic core. In a previous work [20], we studied the properties of paraffin/petroleum asphaltene composites, but the modification of asphaltenes with sulfuric acid and oleum led only to a slight increase in the thermal conductivity of the PCMs.
As an alternative to petroleum asphaltenes, their analogues, technogenic asphaltenes, which were isolated from ethylene tar (ET), a waste product of ethylene production by pyrolysis of hydrocarbon raw materials [21,22], are considered in this paper. Currently, ET is being investigated as a raw material for the synthesis of pitch precursors for various carbon materials, including general purpose carbon fiber [22,23,24] and carbon nanofiber [25]. However, on an industrial scale, ET is used mainly for the production of carbon black or as a component of boiler fuel. It should be noted that ET is a mixture of various compounds, predominantly aromatic [26,27], and is usually characterized by the content of saturated, aromatic, and polar compounds according to the IP 469 method and technogenic asphaltenes, a residue insoluble in heptane according to the IP 143 method. Thus, ET has great potential for the production of various carbon materials and can serve as a valuable source for the extraction of polycyclic aromatic compounds.
In this work, we compared the structural similarity and difference between petroleum and technogenic asphaltenes. For technogenic asphaltenes, a number of features of the composition and properties have been identified, which allow us to consider them as a promising thermal conductivity enhancer for obtaining paraffin-based PCMs. The structure of technogenic asphaltenes (ET-A) was modified by treatment with ammonium persulfate in sulfuric acid (ET-Ox1) and acetic acid (ET-Ox2) media.
For composites of paraffin with technogenic asphaltenes and their modified derivatives, the concentrations of the fillers were determined, at the point at which they possess sedimentation stability while the crystallinity of the systems was not altered significantly. The values of the thermal conductivity for composites of paraffin with technogenic asphaltene were also determined.

2. Results and Discussion

2.1. Characteristics of Technogenic Asphaltenes and Their Modified Derivatives

It should be noted that, in comparison with petroleum asphaltenes Petroleum-A, technogenic asphaltenes ET-A are characterized by a lower molecular weight and polydispersity (Supporting Information, Figure S1), contain almost no heteroatoms (Table 1), but also have polycyclic aromatic nuclei at the heart of the molecular architecture.
According to the Matrix Assisted Laser Desorption/Ionization (MALDI) spectrum (Supporting Information, Figure S1a), ET-A asphaltenes are characterized by a molecular weight distribution from 100 to 1300 m/z, with a peak molecular weight of Mmax = 550 m/z. For comparison, it is worth pointing out that the molecular weight of ovalene with 10 aromatic rings is 398 g/mol, and that of perylene with five aromatic rings is 252 g/mol. Probably, technogenic asphaltenes are represented by oligomeric forms (mainly dimeric) of aromatic structural units obtained as a result of condensation at the pyrolysis of mixed gasoline. Thus, the predominant aromatic compounds previously identified by us in distillate fractions (up to 350 ℃) of ET [26] were derivatives of phenanthrene, biphenyl, naphthalene, fluorine, and pyrene. It can be assumed that the heavy residue of ET (asphaltenes ET-A) is a mixture of the oligomeric forms of these aromatic compounds, as described in [28].
In the infrared (IR) spectrum of ET-A (Figure 1a), there are intense bands of out-of-plane C-H bending vibrations of the aromatic region (3046 and 3024 cm−1, 964–695 cm−1) similar to the C-H vibrations of the ring in the same regions of ovalene’s spectrum (Figure 1b). There are also intense bands of C-H stretching vibrations of the methyl and methylene groups (2845–2975 cm−1, 1453 and 1376 cm−1), as in petroleum asphaltenes.
Studies carried out using a computer simulation of the atomic scale in [19] showed that a large number of peripheral alkyl substituents and a significant polydispersity of petroleum asphaltenes prevent the formation of extended ordered aggregates which could have been capable of heat transfer due to the π–π interaction between the planar polycyclic nuclei. Taking into account that ET-A asphaltenes also have alkyl substituents at polycyclic cores, it was necessary to find methods for modifying their structure.
Thus, the action of strong oxidizing agents on petroleum asphaltenes leads to the removal of aliphatic substituents along the perimeter of the polycondensed aromatic nucleus with the formation of carboxyl groups, which is accompanied by the compaction of the spatial structure [20,29,30]. These approaches were extended to technogenic asphaltenes ET-A, which were modified by treatment with ammonium persulfate in sulfuric acid (ET-Ox1) and acetic acid (ET-Ox2).
Indeed, for modified asphaltenes one can observe growth in the oxygen (in the case of the ET-Ox1 and ET-Ox2 products) and sulfur (in the case of the ET-Ox1 product) content (Table 1). According to XPS data, oxygen is found in the C–O-C and O-C=O groups, while sulfur in the case of the ET-Ox1 product exists in the form of R-SO3H sulfonates (Supporting Information, Figure S2a,b). The XPS spectra of sulfur of ET-Ox1 are doublets of 2p3/2-2p1/2 peaks (spin-orbit splitting) with an intensity ratio of 2/1 and a splitting of 1.18 eV (Supporting Information, Figure S2c) [31,32]. The XPS spectrum of ET-Ox1 also contains two nitrogen peaks (N1s 400.4 and 402.0 eV), which can be attributed to pyrolytic and quaternized nitrogen (Supporting Information, Figure S2d) [33,34], probably obtained as a result of the introduction of ammonium persulfate molecules and the subsequent recombinations of the polyaromatic structures.
IR spectroscopy (Table 2) also confirms an increase in oxidation (content of C=O and C-O groups) and the sulfur content (content of sulfonate RSO3H and sulfoxide S-O groups) in the modified products. The value of the aromaticity coefficient (C=C/CH3+CH2) also increases and the value of the aliphatic coefficient (CH2/C=C) decreases after modification.
The action of a strong oxidizing agent such as ammonium persulfate on technogenic asphaltenes leads, first of all, to oxidation and the introduction of oxygen with the formation of the carboxyl and ether groups and, in the case of the ET-Ox1 product, also to the formation of sulfonic acid groups. At the same time, aliphatic substituents are removed and the polycyclic aromatic structure of the molecules is densified.

2.2. Physicochemical Properties of Paraffin Composition Modified with Asphaltenes

2.2.1. Rheological Properties

When discussing the various properties of the paraffin composites, one should keep in mind their sedimentation stability. Filler sedimentation may lead not only to inhomogeneous distribution, but also to significant changes in the properties of the whole composite. The sedimentation stability of a suspension may be provided by the yield stress [35,36,37].
It is known that paraffin melt is a Newtonian liquid: its viscosity is practically independent of the shear stress [38]. The introduction to paraffin of technogenic asphaltenes ET-A in the amount of 5 wt. % leads to the appearance of a pronounced yield stress in the systems. In the dependences of viscosity on shear stress (Figure 2a), the yield stress looks like an almost vertical region of constant stress. This may be due to the formation of a certain structure (network of contacts) by the filler particles. The strength of this network prevents particles from sedimentation. By increasing the shear stress (or shear rate), this network may break, which can be an explanation of the reverse slope of viscosity vs. the shear stress curves after overcoming the yield stress (marked areas in Figure 2a).
However, by increasing filler concentration up to 10 %, the yield stress value drops significantly. This may be explained by the increase in the probability of the formation of large agglomerates of filler particles, which leads to a decrease in the number of agglomerate particles in the system and to the lower strength of the structural framework [39]. At an ET-A concentration of 30 wt. %, the situation changes again—the yield stress recovers—which may mean that the concentration of asphaltenes becomes sufficient for the agglomerates to be able to form their rather strong structural framework.
The storage G’ and loss G’’ moduli for compositions with 5 and 30% ET-A (Figure 2b) depend very weakly on frequency, with the storage modulus exceeding the loss modulus over the entire frequency range studied. This behavior is typical for gels. In contrast, for a system with 10% ET-A above 1 rad/s, the storage and loss moduli increase with the frequency, with a crossover point where the storage modulus dominates the loss modulus. Some decreases in the modulus with frequency in the low-frequency region can be associated with the process of the destruction of a weak network. Thus, the dynamic test data correlate with the dependences of viscosity on shear stress.
A similar change in the yield strength with filler concentration is observed for composites with asphaltenes ET-OX1 (Figure 3a). The dependences of storage and loss moduli on frequency (Figure 3b), however, are weak for all systems with these types of asphaltenes, and G’ > G’’ for all composites in the entire frequency range. It should be noted that the highest modulus values are typical for compositions with 5 and 30 wt% filler, while for intermediate concentrations (10 and 20 wt. %), they are significantly lower.
For systems with ET-Ox2 asphaltenes, we also observe the deterioration of yield stress and moduli values with the increasing of the filler concentration from 5 to 20 wt% (Figure 4). The system with 20% ET-Ox2 demonstrates the same pattern of frequency dependences of the moduli as the one with 10 wt% of ET-A: there is a drop in the low-frequency range with a growth at higher frequencies, which indicates a very weak network.
The concentration dependence of the yield stress for the discussed systems is shown in Figure 5. It can be concluded from it that at asphaltenes concentrations of 5 and 30 wt%, their particles or aggregates form a stable structural network capable of preventing their sedimentation in the paraffin melt, while at intermediate concentrations, the network is much weaker.

2.2.2. Structure of Composites

According to optical microscopy data, ET-A asphaltenes form spherical particles of about 1 µm in size, assembling into agglomerates of up to 30 µm in size. In dispersions with paraffin, the largest size of the agglomerates is 50 µm (Figure 6a). Asphaltenes ET-Ox1 and ET-Ox2 are particles of an uneven shape with a size of about 1 µm, forming agglomerates of up to 50 and 30 µm in size, respectively. In composites, the size of the agglomerates reaches 70 and 50 µm (Figure 6b,c). The larger size of the agglomerates in composites with ET-Ox1-modified asphaltenes can be associated with their modification, which enhances the interaction between their molecules.
According to the results of the X-ray diffraction analysis, the introduction of asphaltenes of various natures into paraffin has practically no effect on its crystal lattice. Compared to the diffraction pattern of pure paraffin, the diffraction patterns of composites containing asphaltenes lose the peak characteristic of paraffin in the region of 10° in 2θ (Figure 7), and at 15–20°, an insignificant amorphous halo is observed, indicating some amorphization of the structure. One can also note a decrease in the intensity of the peaks in the region of 35–45°. Thus, the data obtained indicate a decrease in the degree of crystallinity of the systems upon the introduction of asphaltenes; however, the crystal structure characteristic of paraffin is retained.
The degree of the crystallinity of systems is linearly related with the amount of heat that will be absorbed or released during the phase transition—the greater the degree of crystallinity, the more heat the system is able to accumulate [40]. The degree of crystallinity of the samples was estimated as the ratio of the heat of fusion of the material experimentally determined by differential scanning calorimetry (DSC) to the heat of fusion of eicosan (244.2 J/g) [41], corrected for the mass fraction of paraffin in a specific system. The introduction of additives in paraffin in the amount of 5–10 wt. % leads to a decrease in paraffin crystallinity by almost 20% (Figure 8). A further increase in the filler concentration slightly improves the situation in the case of ET-Ox1 asphaltenes, stabilizes the values for ET-A, and decreases when filling with ET-Ox2 asphaltenes. Probably, this behavior is associated with the formation of agglomerates by filler particles, which interfere with the packing of paraffin chains.

2.2.3. Thermal Conductivity

The rate of the accumulation and release of thermal energy by a thermal accumulator depends on the thermal conductivity of the composite material [42]. The introduction of technogenic asphaltenes into paraffin leads to a noticeable increase in its thermal conductivity with the growth of the filler concentration (Figure 9). In the case of ET-A and ET-Ox1 asphaltenes, the thermal conductivity values of the composites practically coincide, despite the lower initial value of the thermal conductivity of ET-A asphaltenes compared to paraffin. In this case, the greatest increase in thermal conductivity is 18% which is achieved at a 30 wt. % filler content. In the case of ET-Ox2 asphaltenes, the results stand out noticeably. The thermal conductivity of asphaltenes ET-Ox2 turns out to be higher than the thermal conductivity of paraffin by 58%, and their addition to paraffin in an amount as small as 5 wt. % significantly increases its thermal conductivity, and the maximum increase (by 72%) is achieved with a filler content of 30 wt. %.
This behavior should be related to the modification of asphaltenes and opens up the possibility of their successful use as a filler to increase the thermal conductivity of paraffin.

3. Materials and Methods

3.1. Materials

Highly purified paraffin grade P-2 (Lukoil, Russia), which is a mixture of solid hydrocarbons with a predominantly normal structure and a melting point of 52–58 °C, was used as a phase change material.
ET, a byproduct of pyrolysis of mixed gasoline in the production of ethylene, was provided by PJSC Nizhnekamskneftekhim (Russia). The complete characterization of ET (fractional composition, group hydrocarbon composition of distillate fractions, etc.) is presented in [26]. Technogenic asphaltenes, designated as “ET-A”, and petroleum asphaltenes, designated as “Petroleum-A”, were isolated by the IP 143 method from ET and crude oil from the Ashalchinskoye field (Russia), respectively. The yield of ET-A asphaltenes from ET was 14 wt%, whereas the weight fraction of Petroleum-A asphaltenes in the crude oil was 7.1 wt%. All solvents and reagents used in this study were obtained from Sigma-Aldrich and used as received.

3.1.1. Modification of ET-A Asphaltenes with Ammonium Persulfate in Sulfuric Acid

A total of 20 g of ammonium persulfate was mixed with 60 mL of concentrated sulfuric acid (98 wt% concentration), and then 2 g of ET-A asphaltenes were added to the resulting mixture by stirring in small portions over 1 h. A strong exothermic effect and foaming were observed. After adding the last portion of asphaltenes, stirring was continued for 1 h, after which 50 mL of distilled water was slowly added and kept under stirring for 2 h more. Next, the reaction mass was poured into 500 mL of distilled water, and the black precipitate was filtered off, which was washed with water until neutral and dried under vacuum. The yield of the product, hereinafter referred to as “ET-Ox1”, was 88 wt%.

3.1.2. Modification of ET-A Asphaltenes with Ammonium Persulfate in Acetic Acid

A total of 1 g of ET-A asphaltenes was dissolved in 30 mL of methylene chloride. Then, 60 mL of glacial acetic acid followed by 20 g of ammonium persulfate (in small parts) was added, while stirring, to the solution. Then, 0.1 mL of sulfuric acid (98%) was added as a catalyst. The reaction mass was stirred for another 3 h, after which 10 mL of distilled water was added and stirred for another hour. After that, the reaction mass was kept for 12 h, and then poured into 500 mL of distilled water, and the aqueous layer was separated from the black organic layer. The organic layer was evaporated from methylene chloride and the residue was dried under vacuum. The yield of the product, hereinafter referred to as “ET-Ox2”, was 98 wt %.

3.2. Preparation of Composites

Technogenic asphaltenes and their modified derivatives were ground in an IKA A11 basic mill at 28,000 rpm for 10 min. Composite samples were prepared by introducing 30 wt% of the filler obtained by grinding into the molten paraffin at 80 °C with constant stirring using an overhead stirrer, Heidolph RZR 2051, at 500 rpm. To obtain samples with a lower filler concentration, the concentrated mixtures were diluted step by step with paraffin to the desired concentration. Three series of samples were obtained in this way: composites filled with technogenic asphaltenes ET-A and modified asphaltenes ET-Ox1 and ET-Ox2. The filler concentration was 30, 20, 10, and 5 wt % for each system.

3.3. Methods

3.3.1. MALDI

Matrix-assisted laser desorption/ionization mass spectra were obtained by UltraFlex III TOF/TOF mass-spectrometer (Bruker Daltonik GmbH, Bremen, Germany) in a linear mode with Nd:YAG laser (λ = 355 nm). The spectra were obtained with 25 kV of accelerating voltage and 30 ns of acceleration delay. The data were processed by using FlexAnalysis 3.0 software (Bruker Daltonik GmbH, Bremen, Germany). Additionally, 1,8,9-Trihydroxyanthracene was used as a matrix. The metal target MTP AnchorChipTM was used. In addition, 0.5 µL of 1% solutions of the matrix and the sample in toluene were successfully spotted on the target and evaporated. Spectra were collected for all spots using 250 shots per spectrum. Positively charged ions were analyzed.

3.3.2. XPS

X-ray photoelectron spectroscopy was performed on a PHI 5000 Versa Probe II spectrometer (ULVAC-PHI, Inc., USA). The excitation source was monochromatized Al Kα radiation (hν = 1486.6 eV), with power of 50 W and beam diameter of 200 µm. We used a charge neutralization system because a slight electrostatic charge was observed, which distorted the spectra. Atomic concentrations were determined from survey spectra using the relative elemental sensitivity factors of the C1s, O1s, N1s, and S2p lines. The binding energies, Eb, of photoelectronic lines were determined from high-resolution spectra, taken at an analyzer transmission energy of 23.5 eV and a collection density of 0.2 eV/step. The binding energy scale, Eb, was calibrated for Au4f—83.96 eV—and Cu2p3—932.62 eV. The Eb scale was corrected for the first peak in the C1s spectrum (with the lowest Eb value of 284.7 eV), since the samples contain a large number of carbon atoms in aromatic fragments—the presence in the C1s spectrum with Eb peak in the region of 291 eV, the so-called shake-up satellite representing sp2 carbon bonds.

3.3.3. Elemental Analysis

Elemental composition of samples was determined using a CHNS analyzer Vario Macro cube (Elementar Analysensysteme GmbH, Germany).

3.3.4. IR Spectroscopy

IR spectra of the compounds were recorded in the range of 4000–400 cm−1 on a Vector-22 IR-Fourier spectrometer (Bruker, Germany) with an optical resolution of 4 cm−1. Samples were prepared in tablets with KBr (Acros Organics 206391000). To study the structural and group composition of samples, spectral coefficients were calculated: CH2/C=C—aliphaticity (D1450/D1600), C=C/CH2+CH3—aromaticity (D1600/D1450+1380), C=O/C=C—degree of oxidation I (D1720/D1600), C-O-C/C=C—degree of oxidation II (D1230/D1600), RSO3H—degree of sulfonation (D1030/D1600), and SO = D1160/D1600—(degree of sulfoxidation). The spectra were processed and analyzed using OPUS Version 6.5 software (Bruker Optik GmbH, Germany).

3.3.5. Optical Microscopy

The study of the morphology of the obtained samples was carried out using optical microscopy. A Biomed microscope with 10x magnification and a digital video camera was used to obtain images of filled samples.

3.3.6. Rheological Properties

The rheological properties of the compositions obtained were studied on a DHR-2 rotary rheometer (TA Instruments, USA) using a measuring cone-plane unit (the cone diameter was 25 mm, the angle between the conical surface and the plate was 2°). The flow curves of the samples were obtained at 80 °C with a stepwise increase of the shear rate from 10−3 to 1000 s−1.

3.3.7. X-ray Diffraction

The effect of filler introduction on the degree of crystallinity of paraffin was studied by X-ray diffraction on a Rigaku Rotaflex D/max-RC instrument (Rigaku, Japan, Japan) using CuKα radiation with a wavelength of λ = 0.154 nm. Diffractograms were obtained in the range of 3–70° in 2θ with a step of 0.04° and a recording rate of 4°/min.

3.3.8. Thermophysical Properties

The amount of heat released or absorbed by pure paraffin and its composites filled with asphaltenes as a result of the phase transitions was measured by DSC on the MDSC 2920 calorimeter (TA Instruments, New Castle, DE, USA) in the argon atmosphere. Thermograms were recorded in the temperature range of 0–100 °C at a heating/cooling rate of 2 °C/min.
The measurements of the thermal conductivity of paraffin, asphaltenes, and composites were carried out at 20 °C using a KITT-Nanocomposite device (KB “Teplofon”, Russia). Samples were preliminarily prepared from paraffin or composites in the form of tablets 10 mm in diameter and 5 mm thick. Asphaltenes tablet samples were prepared by compaction of the asphaltenes powders in a mold at room temperature under light pressure. Then the samples were placed in a measuring cell made of neutral material. The method of measurement consisted in uniformly preheating a sample and then its monotonous cooling from one side using a Peltier element, with calculation of the value of heat conductivity using the temperature difference at the edges of the sample and the value of heat flow.
The research methodology is presented in Figure 10.

4. Conclusions

In the present work, inexpensive carbon additives obtained from wastes of ethylene production by the pyrolysis of hydrocarbon feedstock were studied as enhancers of the thermal conductivity of PCMs. Technogenic asphaltenes and their modified derivatives have been studied as fillers to enhance the thermal conductivity of paraffin. The following conclusions were made:
(1)
Due to the presence of a polycyclic aromatic core, technogenic and petroleum asphaltenes can be considered as carbon nanofillers, similar in structural properties to small fragments of graphene. The revealed features of the structure of technogenic asphaltenes—high condensation and an almost complete absence of heteroatoms in polyaromatic systems—make them a more promising basis for obtaining PCM thermal conductivity enhancers by chemical modification.
(2)
The oxidative modification of technogenic asphaltenes makes it possible to change their composition in a controlled way. In the case of oxidation with ammonium persulfate in sulfuric acid, significant changes are observed in the structure of modified technogenic asphaltenes associated with the formation of more condensed structures and a noticeable increase in the oxygen content in the average molecule due to the formation of carboxyl, ether, and sulfo groups, as well as the appearance of a significant amount of heteroatoms, especially on the surface. The process of the oxidation of technogenic asphaltenes with ammonium persulfate in acetic acid does not lead to significant changes in their structure and is associated mainly with the formation of carboxyl and ether groups.
(3)
It was found that the introduction of 5 and 30 wt. % of such fillers leads to the formation of an internal network structure, which contributes to an increase in the sedimentation stability of their suspensions in paraffin, while intermediate concentrations of asphaltenes are not so effective.
(4)
As a result, the addition of modified technogenic asphaltenes oxidized with ammonium persulfate in acetic acid in an amount of 5–30 wt% allows the increase of the thermal conductivity of paraffin by 58–72%, respectively.
(5)
The addition of technogenic asphaltenes oxidized with ammonium persulfate in sulfuric acid does not provide a similar increase in the thermal conductivity of paraffin. This is probably due to the presence of sulfo groups, RSO3H, formed in presence of sulfuric acid, which enhance interactions between molecules, but also lead to poor (non-uniform) distribution in the wax. As a result, a significant increase in the thermal conductivity was not achieved.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/molecules28030949/s1, Figure S1: MALDI spectra of technogenic (a) and petroleum (b) asphaltenes; Figure S2: XPS spectra of oxygen (a,b), sulfur (c), and nitrogen (d) in ET-Ox1 and ET-Ox2 products.

Author Contributions

Conceptualization, S.V.A. and M.R.Y.; experimental work, S.N.G., V.V.M., D.N.B., and Y.Y.B.; writing—original draft preparation, S.N.G., V.V.M., and Y.Y.B.; writing—review and editing, D.N.B., S.V.A., Y.Y.B., and M.R.Y. All authors have read and agreed to the published version of the manuscript.

Funding

This research was performed with financial support from the Russian Science Foundation (Project no. 19-13-00178).

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Acknowledgments

The authors thank the staff of the Distributed Collective Spectral-Analytical Center for Studying the Structure, Composition, and Properties of Substances and Materials of the Federal Research Center, Kazan Scientific Center of the Russian Academy of Sciences for the conducted studies. The authors thank I.S. Levin for registering diffractograms in the Shared Research Center, “Analytical center of deep oil processing and petrochemistry of TIPS RAS”, and A.V. Kostyuk for registering DSC thermogramms.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Sarier, N.; Onder, E. Organic phase change materials and their textile applications: An overview. Thermochim. Acta 2012, 540, 7–60. [Google Scholar] [CrossRef]
  2. Wang, J.; Li, Y.; Zheng, D.; Mikulčić, H.; Vujanović, M.; Sundén, B. Preparation and thermophysical property analysis of nanocomposite phase change materials for energy storage. Renew. Sustain. Energy Rev. 2021, 151, 111541. [Google Scholar] [CrossRef]
  3. Karaipekli, A.; Biçer, A.; Sarı, A.; Tyagi, V.V. Thermal characteristics of expanded perlite/paraffin composite phase change material with enhanced thermal conductivity using carbon nanotubes. Energy Convers. Manag. 2017, 134, 373–381. [Google Scholar] [CrossRef]
  4. El Idi, M.M.; Karkri, M.; Kraiem, M. Preparation and effective thermal conductivity of a Paraffin/Metal Foam composite. J. Energy Storage 2021, 33, 102077. [Google Scholar] [CrossRef]
  5. Chaichan, M.T.; Kamel, S.H.; Al-Ajeely, A.N.M. Thermal conductivity enhancement by using nano-material in phase change material for latent heat thermal energy storage systems. Saussurea 2015, 5, 48–55. [Google Scholar]
  6. Wu, S.; Chen, Q.; Chen, D.; Peng, D.; Ma, Y. Multiscale study of thermal conductivity of boron nitride nanosheets/paraffin thermal energy storage materials. J. Energy Storage 2021, 41, 102931. [Google Scholar] [CrossRef]
  7. Ma, X.; Wu, S.; Yi, Z.; Peng, D.; Zhang, J. The effect mechanism of functionalization on thermal conductivity of boron nitride nanosheets/paraffin composites. Int. J. Heat Mass Transf. 2019, 137, 790–798. [Google Scholar] [CrossRef]
  8. Balandin, A.A.; Ghosh, S.; Bao, W.; Calizo, I.; Teweldebrhan, D.; Miao, F.; Lau, C.N. Superior thermal conductivity of single-layer graphene. Nano Lett. 2008, 8, 902–907. [Google Scholar] [CrossRef]
  9. Amin, M.; Putra, N.; Kosasih, E.A.; Prawiro, E.; Luanto, R.A.; Mahlia, T.M.I. Thermal properties of beeswax/graphene phase change material as energy storage for building applications. Appl. Therm. Eng. 2017, 112, 273–280. [Google Scholar] [CrossRef]
  10. Yu, Z.T.; Fang, X.; Fan, L.W.; Wang, X.; Xiao, Y.Q.; Zeng, Y.; Cen, K.F. Increased thermal conductivity of liquid paraffin-based suspensions in the presence of carbon nano-additives of various sizes and shapes. Carbon 2013, 53, 277–285. [Google Scholar] [CrossRef]
  11. Kiršanskas, G.; Li, Q.; Flensberg, K.; Solomon, G.C.; Leijnse, M. Designing π-stacked molecular structures to control heat transport through molecular junctions. Appl. Phys. Lett. 2014, 105, 233102. [Google Scholar] [CrossRef]
  12. Emrick, T.; Pentzer, E. Nanoscale assembly into extended and continuous structures and hybrid materials. Npg Asia Mater. 2013, 5, e43. [Google Scholar] [CrossRef] [Green Version]
  13. Balandin, A.A. Thermal properties of graphene and nanostructured carbon materials. Nat. Mater. 2011, 10, 569–581. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  14. Lin, Y.; Jia, Y.; Alva, G.; Fang, G. Review on thermal conductivity enhancement, thermal properties and applications of phase change materials in thermal energy storage. Renew. Sustain. Energy Rev. 2018, 82, 2730–2742. [Google Scholar] [CrossRef]
  15. Liu, X.; Rao, Z. Experimental study on the thermal performance of graphene and exfoliated graphite sheet for thermal energy storage phase change material. Thermochim. Acta 2017, 647, 15–21. [Google Scholar] [CrossRef]
  16. Bhattacharya, M. Polymer nanocomposites—A comparison between carbon nanotubes, graphene, and clay as nanofillers. Materials 2016, 9, 262. [Google Scholar] [CrossRef] [Green Version]
  17. Wu, Y.; Yan, X.; Meng, P.; Sun, P.; Cheng, G.; Zheng, R. Carbon black/octadecane composites for room temperature electrical and thermal regulation. Carbon 2015, 94, 417–423. [Google Scholar] [CrossRef]
  18. Zhong, Y.; Li, S.; Wei, X.; Liu, Z.; Guo, Q.; Shi, J.; Liu, L. Heat transfer enhancement of paraffin wax using compressed expanded natural graphite for thermal energy storage. Carbon 2010, 48, 300–304. [Google Scholar] [CrossRef]
  19. Glova, A.D.; Nazarychev, V.M.; Larin, S.V.; Lyulin, A.V.; Lyulin, S.V.; Gurtovenko, A.A. Asphaltenes as novel thermal conductivity enhancers for liquid paraffin: Insight from in silico modeling. J. Mol. Liq. 2022, 346, 117112. [Google Scholar] [CrossRef]
  20. Makarova, V.V.; Gorbacheva, S.N.; Kostyuk, A.V.; Antonov, S.V.; Borisova, Y.Y.; Borisov, D.N.; Yakubov, M.R. Composites based on neat and modified asphaltenes and paraffin: Structure, rheology and heat conductivity. J. Energy Storage 2022, 47, 103595. [Google Scholar] [CrossRef]
  21. Liu, J.; Chen, X.; Xie, Q.; Liang, D. Controllable synthesis of isotropic pitch precursor for general purpose carbon fiber using waste ethylene tar via bromination–dehydrobromination. J. Clean. Prod. 2020, 271, 122498. [Google Scholar] [CrossRef]
  22. Ge, C.Z.; Sun, Z.L.; Yang, H.X.; Long, D.H.; Qiao, W.M.; Ling, L.C. Preparation and characterization of high softening point and homogeneous isotropic pitches produced from distilled ethylene tar by a novel bromination method. New Carbon Mater. 2018, 33, 71–81. [Google Scholar] [CrossRef]
  23. Yang, J.; Nakabayashi, K.; Miyawaki, J.; Yoon, S.H. Preparation of pitch based carbon fibers using Hyper-coal as a raw material. Carbon 2016, 106, 28–36. [Google Scholar] [CrossRef]
  24. Yang, J.; Nakabayashi, K.; Miyawaki, J.; Yoon, S.H. Preparation of isotropic pitch-based carbon fiber using hyper coal through co-carbonation with ethylene bottom oil. J. Ind. Eng. Chem. 2016, 34, 397–404. [Google Scholar] [CrossRef]
  25. Kim, B.-J.; Kil, H.; Watanabe, N.; Seo, M.-H.; Kim, B.-H.; Yang, K.S.; Kato, O.; Miyawaki, J.; Mochida, I.; Yoon, S.-H. Preparation of novel isotropic pitch with high softening point and solvent solubility for pitch-based electrospun carbon nanofiber. Curr. Org. Chem. 2013, 17, 1463–1468. [Google Scholar] [CrossRef]
  26. Borisova, Y.Y.; Mironov, N.A.; Yakubova, S.G.; Borisov, D.N.; Kosachev, I.P.; Yakubov, M.R. Application of Ethylene Tar as an Additive in Visbreaking of Petroleum Vacuum Residue. Energy Fuels 2021, 35, 15684–15694. [Google Scholar] [CrossRef]
  27. Mukhamedzyanova, A.A.; Gimaev, R.N.; Khaibullin, A.A.; Telyashev, E.G. Research of high-quality descriptions of heavy pyrolysis tar. Bull. Bashkir Univ. 2012, 17, 909–915. [Google Scholar]
  28. Burgess, W.A.; Thies, M.C. Molecular structures for the oligomeric constituents of petroleum pitch. Carbon 2011, 49, 636–651. [Google Scholar] [CrossRef]
  29. Borisov, D.N.; Foss, L.E.; Shabalin, K.V.; Musin, L.I.; Musin, R.Z. Oxidative Cleavage of Asphaltenes Under Mild Conditions. Chem. Technol. Fuels Oils 2019, 55, 552–556. [Google Scholar] [CrossRef]
  30. Shabalin, K.V.; Musin, L.I.; Foss, L.E.; Nagornova, O.A.; Morozov, V.I.; Borisov, D.N.; Yakubov, M.R. Preparation of Redox Ion-Exchange Materials Based on Petroleum Asphaltenes. Pet. Chem. 2022, 62, 222–228. [Google Scholar] [CrossRef]
  31. Induchoodan, G.; Jansson, H.; Swenson, J. Influence of graphene oxide on asphaltene nanoaggregates. Colloids Surf. A Physicochem. Eng. Asp. 2021, 630, 127614. [Google Scholar] [CrossRef]
  32. Siow, K.S.; Britcher, L.; Kumar, S.; Griesser, H.J. XPS Study of Sulfur and Phosphorus Compounds with Different Oxidation States. Sains Malays. 2018, 47, 1913–1922. [Google Scholar] [CrossRef]
  33. Li, W.; Tang, Y.; Zhao, Q.; Wei, Q. Sulfur and nitrogen in the high-sulfur coals of the Late Paleozoic from China. Fuel 2015, 155, 115–121. [Google Scholar] [CrossRef]
  34. Guzmán, H.J.; Isquierdo, F.; Carbognani, L.; Vitale, G.; Scott, C.E.; Pereira-Almao, P. X-ray photoelectron spectroscopy analysis of hydrotreated athabasca asphaltenes. Energy Fuels 2017, 31, 10706–10717. [Google Scholar] [CrossRef]
  35. Barnes, H.A. The yield stress—A review or ‘παντα ρει’—Everything flows? J. Non-Newton. Fluid Mech. 1999, 81, 133–178. [Google Scholar] [CrossRef]
  36. Willenbacher, N.; Georgieva, K. Rheology of disperse systems. In Product Design and Engineering: Formulation of Gels and Pastes; John Wiley & Sons: Hoboken, NJ, USA, 2013; Volume 44. [Google Scholar]
  37. Dzuy, N.Q.; Boger, D.V. Yield stress measurement for concentrated suspensions. J. Rheol. 1983, 27, 321–349. [Google Scholar] [CrossRef]
  38. Gorbacheva, S.N.; Makarova, V.V.; Ilyin, S.O. Hydrophobic nanosilica-stabilized graphite particles for improving thermal conductivity of paraffin wax-based phase-change materials. J. Energy Storage 2021, 36, 102417. [Google Scholar] [CrossRef]
  39. Ancey, C.; Jorrot, H. Yield stress for particle suspensions within a clay dispersion. J. Rheol. 2001, 45, 297–319. [Google Scholar] [CrossRef]
  40. Raine, H.C.; Richards, R.B.; Ryder, H. The heat capacity, heat of solution, and crystallinity of polythene. Trans. Faraday Soc. 1945, 41, 56–64. [Google Scholar] [CrossRef]
  41. Babaev, B.D. Principles of heat accumulation and heat-accumulating materials in use. High Temp. 2014, 52, 736. [Google Scholar] [CrossRef]
  42. Kibria, M.A.; Anisur, M.R.; Mahfuz, M.H.; Saidur, R.; Metselaar, I.H.S.C. A review on thermophysical properties of nanoparticle dispersed phase change materials. Energy Convers. Manag. 2015, 95, 69–89. [Google Scholar] [CrossRef]
Molecules 28 00949 g001 550
Figure 1. IR spectra of petroleum asphaltenes Petroleum-A (black) and technogenic asphaltenes ET-A (red) (a), ovalene (b).
Figure 1. IR spectra of petroleum asphaltenes Petroleum-A (black) and technogenic asphaltenes ET-A (red) (a), ovalene (b).
Molecules 28 00949 g001
Molecules 28 00949 g002 550
Figure 2. Dependence of viscosity on shear stress (a) and frequency dependences of storage and loss moduli (b) of paraffin composites containing ET-A asphaltenes, T = 80 °C. Marked areas in (a) with reverse slope correspond to deterioration of the structural network of composites.
Figure 2. Dependence of viscosity on shear stress (a) and frequency dependences of storage and loss moduli (b) of paraffin composites containing ET-A asphaltenes, T = 80 °C. Marked areas in (a) with reverse slope correspond to deterioration of the structural network of composites.
Molecules 28 00949 g002
Molecules 28 00949 g003 550
Figure 3. Dependence of viscosity on shear stress (a) and frequency dependences of storage and loss moduli (b) of paraffin composites containing ET-Ox1 asphaltenes, T = 80 °C.
Figure 3. Dependence of viscosity on shear stress (a) and frequency dependences of storage and loss moduli (b) of paraffin composites containing ET-Ox1 asphaltenes, T = 80 °C.
Molecules 28 00949 g003
Molecules 28 00949 g004 550
Figure 4. Dependence of viscosity on shear stress (a) and frequency dependences of storage and loss moduli (b) of paraffin composites containing ET-Ox2 asphaltenes, T = 80 °C.
Figure 4. Dependence of viscosity on shear stress (a) and frequency dependences of storage and loss moduli (b) of paraffin composites containing ET-Ox2 asphaltenes, T = 80 °C.
Molecules 28 00949 g004
Molecules 28 00949 g005 550
Figure 5. Concentration dependence of the yield stress of paraffin dispersions containing fillers.
Figure 5. Concentration dependence of the yield stress of paraffin dispersions containing fillers.
Molecules 28 00949 g005
Molecules 28 00949 g006 550
Figure 6. Optical micrographs of paraffin containing 5 wt. % asphaltenes ET-A (a), ET-Ox1 (b), ET-Ox2 (c).
Figure 6. Optical micrographs of paraffin containing 5 wt. % asphaltenes ET-A (a), ET-Ox1 (b), ET-Ox2 (c).
Molecules 28 00949 g006
Molecules 28 00949 g007 550
Figure 7. X-ray diffraction patterns of systems based on paraffin (1) and its composites containing 20 wt. % asphaltenes ET-A (2), ET-Ox1 (3), ET-Ox2 (4), T = 25 °C.
Figure 7. X-ray diffraction patterns of systems based on paraffin (1) and its composites containing 20 wt. % asphaltenes ET-A (2), ET-Ox1 (3), ET-Ox2 (4), T = 25 °C.
Molecules 28 00949 g007
Molecules 28 00949 g008 550
Figure 8. Concentration dependence of the degree of crystallinity of composites based on paraffin containing asphaltenes of various natures.
Figure 8. Concentration dependence of the degree of crystallinity of composites based on paraffin containing asphaltenes of various natures.
Molecules 28 00949 g008
Molecules 28 00949 g009 550
Figure 9. Concentration dependence of the thermal conductivity of composites based on paraffin containing asphaltenes of various nature, T = 25 °C.
Figure 9. Concentration dependence of the thermal conductivity of composites based on paraffin containing asphaltenes of various nature, T = 25 °C.
Molecules 28 00949 g009
Molecules 28 00949 g010 550
Figure 10. Research methodology flow chart.
Figure 10. Research methodology flow chart.
Molecules 28 00949 g010
Table
Table 1. Content of elements in asphaltene samples according to X-ray photoelectron spectroscopy (XPS) data (on the surface) and CHNS elemental analysis.
Table 1. Content of elements in asphaltene samples according to X-ray photoelectron spectroscopy (XPS) data (on the surface) and CHNS elemental analysis.
Asphaltene
Samples		Concentration of Elements, wt. %
at the Surface (XPS Data)in the Whole Sample (CHNS Analysis Data)
CNOSCHNSO 1
Petroleum-A93.01.02.13.680.98.12.16.92.0
ET-A99.3-0.7-92.26.5--1.3
ET-Ox171.61.123.34.051.94.91.66.435.2
ET-Ox296.5-3.5-83.86.1-0.79.4
1 the oxygen concentration was calculated as a difference between 100% and the sum of the concentrations of the other elements.
Table
Table 2. Spectral coefficients derived from IR spectroscopy data for samples.
Table 2. Spectral coefficients derived from IR spectroscopy data for samples.
Asphaltene SamplesSpectral Coefficients
CH2/
C=C		C=C/
CH3+CH2		C=O/
C=C		C-O/
C=C		RSO3H/
C=C		S-O/C=C
ET-A1.330.49----
ET -Ox10.821.220.891.201.211.31
ET -Ox21.020.540.780.890.680.65
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Gorbacheva, S.N.; Borisova, Y.Y.; Makarova, V.V.; Antonov, S.V.; Borisov, D.N.; Yakubov, M.R. Modified Technogenic Asphaltenes as Enhancers of the Thermal Conductivity of Paraffin. Molecules 2023, 28, 949. https://doi.org/10.3390/molecules28030949

AMA Style

Gorbacheva SN, Borisova YY, Makarova VV, Antonov SV, Borisov DN, Yakubov MR. Modified Technogenic Asphaltenes as Enhancers of the Thermal Conductivity of Paraffin. Molecules. 2023; 28(3):949. https://doi.org/10.3390/molecules28030949

Chicago/Turabian Style

Gorbacheva, Svetlana N., Yulia Yu. Borisova, Veronika V. Makarova, Sergey V. Antonov, Dmitry N. Borisov, and Makhmut R. Yakubov. 2023. "Modified Technogenic Asphaltenes as Enhancers of the Thermal Conductivity of Paraffin" Molecules 28, no. 3: 949. https://doi.org/10.3390/molecules28030949

Article Metrics

Back to TopTop