A Symmetric Controllable Hyperchaotic Hidden Attractor

Abstract

By introducing a simple feedback, a hyperchaotic hidden attractor is found in the newly proposed Lorenz-like chaotic system. Some variables of the equilibria-free system can be controlled in amplitude and offset by an independent knob. A circuit experiment based on Multisim is consistent with the theoretic analysis and numerical simulation.

1. Introduction

As we all know, chaos is ubiquitous in nature and human society, and has great potential in engineering applications. However, there exists great challenge in conditioning broadband chaotic signals, and appropriate amplitude and polarity are the key specifications for chaos generation and transmission [1,2,3], and therefore, recently great efforts have been made on the research of amplitude control and offset boosting. Normally, the amplitude of system variable requires further adjusting a couple of parameters. In many cases, a unipolar signal is more suitable for transmitting in inter-coupled integrated circuits. Such a challenge exists in the conversion from the bipolar signal to unipolar signal. An independent non-bifurcation parameter to rescale the signal without revising the Lyapunov exponents is important for chaos application. Suitable signal control saves the modulator in chaos-based applications [4,5], including amplitude control [6,7] and offset boosting [8,9].

In addition, hidden attractors exist in chaos, but one cannot find them from the neighborhood of any equilibrium point. Thus, it is of great value in theoretical and physical significance and engineering application to study the realization method of hidden attractors. The Chua system, Lorenz-like systems, and the chaotic systems with stable equilibria [10,11,12,13,14,15], line equilibria [16,17,18], or no equilibria [19,20,21,22,23,24] give us impressive points. Hyperchaos with higher complexity is beneficial to secure communication, so some research extends to hyperchaos. A hyperchaotic system with a hidden attractor was proposed by Wang et al. [25]; Chlouverakis and Sprott [26] claimed the simplest hyperchaotic snap system in algebra; and Yuan et al. [27] showed a memristive multi-scroll hyperchaotic system. Other many hyperchaotic systems have come out of the Lorenz-like system [28,29,30,31]. Some other hyperchaotic ones have been proposed, including a memristive hyperchaotic system [32,33], fractional order hyperchaotic system [34,35] or hyperchaotic multi-wing system [36,37]. To the best of our knowledge, there is no relevant research on a hyperchaotic hidden attractor with geometric control. Based on a three-dimensional Lorenz-like system, Wang et al. [38] put forward a hyperchaotic system for producing multi-wing attractors; while in this work, the proposed system has four features as follows:

I)

There exists a parameter to control amplitude and frequency of signals in a small range.

II)

Amplitude of x and y can be controlled simultaneously.

III)

There is an offset boosting controller.

IV)

A special parameter can realize both amplitude and offset control of one system variable.

As shown in Figure 1, the proposed hyperchaotic system has multiple independent geometric controllers including controllers for rescaling amplitude, frequency and offset. Some of the reported 4-D hyperchaotic Lorenz-like systems are listed in

Table 1. Comparison of the Lorenz-like hyperchaotic systems.

Reference	Number of Terms	Number of Equilibrium	Amplitude/Frequency Control	Amplitude/Offset Control
[15]	9	one	no	not mentioned
[28]	10	line equilibrium	no	not mentioned
[30]	10	one	no	not mentioned
[31]	9	one	no	not mentioned
[38]	9	no	no	not mentioned
this work	9	no	yes	yes

. In the paper, the system controllers are signal controllers and multistability observers as well. In Section 2, the mathematical model of the hyperchaotic system is given. In Section 3, complex dynamic behavior is analyzed. The process of amplitude control and offset boosting is discussed in Section 4. In Section 5, multistability is investigated. In Section 6, the analog circuit is given. Finally, we give the conclusions and discussion.

2. Model Description

A 3-D Lorenz-like chaotic system is proposed by Cang et al [39], which is,

$$\{\begin{array}{l}\dot{x}=-ay-xz,\\ \dot{y}=-x+xz,\\ \dot{z}=-d-xy.\end{array}$$

(1)

System (1) has a simple rotational symmetric structure with six terms. Based on system (1), a new hyperchaotic system is proposed as,

$$\{\begin{array}{l}\dot{x}=-ay-xz-u,\\ \dot{y}=-cx+xz,\\ \dot{z}=-b-mxy,\\ \dot{u}=kx-y.\end{array}$$

(2)

where x, y, z, u are system variables, and a, b, c, k are bifurcation parameters of system (2). When a = 5, b = 4, c = 1, k = 0.5 and m = 1, system (2) has a hyperchaotic attractor with Lyapunov exponents (0.3606, 0.1222, 0, −1.4827) and a Kaplan-Yorke dimension of D_KY = 3.3256 under initial conditions (1, −1, −1, 1), as shown in Figure 2.

The hyper-volume contraction is

$$\nabla V=\frac{\partial \dot{x}}{\partial x}+\frac{\partial \dot{y}}{\partial y}+\frac{\partial \dot{z}}{\partial z}+\frac{\partial \dot{u}}{\partial u}=-z$$

(3)

When a = 5, b = 4, c = 1 and k = 0.5, the dissipative curve of Equation (3) is as shown in Figure 3. The negative average of $\nabla V$ proves that system (2) is dissipative.

3. Basic Dynamic Analysis

3.1. Anylis of Equilibria

For system (2), the equilibria can be solved by the following equation:

$$\{\begin{array}{l}-ay-xz-u=0\\ -cx+xz=0\\ -b-mxy=0\\ kx-y=0\end{array}$$

(4)

The fourth equation indicates that $y=kx$, but the third equation means that $b=-mxy$, then b = −mkx², which means that there is no real solution, correspondingly the hyperchaotic attractor of system (2) is hidden.

3.2. Bifurcation Analysis

For system (2), the parameters modify the dynamics effectively. To make the demonstration simpler, we ignore the multistability caused by the special structure of symmetry. When b = 4, c = 1, k = 0.5, m = 1 under initial conditions (1, −1, −1, 1), Lyapunov exponent spectra and bifurcation diagram when a varies in [−10, 23.4] are shown in Figure 4, where a typical transition from period to chaos shows up and finally system (1) results in the state of hyperchaos. Typical phase trajectories are shown in Figure 5. Quasi-periodicity was not found in the examination interval of system (2). When a = 5, c = 1, k = 0.5, m = 1 and initial conditions are (1, −1, −1, 1), when b varies in [0, 15], system (2) heads to hyperchaos from chaos. Lyapunov exponent spectra and bifurcation diagrams are shown in Figure 6, which shows a robust hyperchaos. Both cases have almost linearly scaled Lyapunov exponents in specific regions indicating the function of frequency rescaling.

Comparing Figure 4 and Figure 6, we can see that the parameter a or b visits chaos quickly but modifies the solution in its own way. The parameter a almost has positive correlation with amplitude in a limited range. Meanwhile parameter b has positive correlation with amplitude and frequency, which is distinct and different from other systems. Typical phase trajectories and waveforms are shown in Figure 7.

Fix the parameters a = 5, b = 4, k = 0.5, m = 1, when parameter c varies in [0, 1.7]; the Lyapunov exponent spectra and bifurcation diagram are shown in Figure 8a,b. When c varies in [0, 1.4], system (2) exhibits hyperchaos, while when c varies in [1.4, 1.7], system (2) presents chaos. When a = 5, b = 4, c = 1 and m = 1, the parameter k varies in [0.15, 7.8]; the Lyapunov exponent spectra and bifurcation diagram are shown in Figure 8c,d. When k varies in [0.15, 1.82], system (2) keeps chaos, and when c varies in [1.82, 7.8], system (2) exhibits hyperchaos. Comparing the Lyapunov exponents controlled by parameters c and k, system (2) has relatively robust hyperchaos under the parameters c.

3.3. Amplitude Control

Besides the above two control knobs, the parameter m in the third dimension in system (2) is a single non-bifurcation knob for amplitude control. To understand this rescaling mechanism, we turn back to the initial system (2). Here, we take the transformation: $x\to hx,y\to hy,z\to z,$ $u\to hu(h>0)$, which only leaves an additional coefficient in the third dimension:

$$\{\begin{array}{l}\dot{x}=-ay-xz-u,\\ \dot{y}=-cx+xz,\\ \dot{z}=-b-m{h}^{2}xy,\\ \dot{u}=kx-y.\end{array}$$

(5)

indicating that the amplitude of variables x, y and u can be controlled by the parameter m, with the signal z unchanged. It also has no effect on the frequency of the hyperchaotic chaotic signals.

The output signals are controlled by the non-bifurcation parameter m in system (2). As shown in Figure 9, the amplitude of the signals x, y and u are rescaled by the non-bifurcation parameter m. When m = 0.25, the amplitudes of the x, y and u signals are very large. The amplitudes of the x, y and u signals decrease with an inverse proportion to the parameter m without changing the amplitude of z. Figure 10 shows the phase trajectories on the planes of x-u and y-z when the control parameter m varies.

As we can see in Figure 11a, when the parameter m varies in [0, 5], the average of the absolute values of state variables x, y and u significantly decreases with an inverse proportion to m, while the average of signal z basically has no change. The corresponding Lyapunov exponent spectrum of parameter m varies in [0, 5] are shown in Figure 11b. It can be further proved that the parameter m of system (2) does not change the frequency of the signals.

3.4. Offset Boosting

Since the derivative of a constant is zero, when a constant is added to a variable in a dynamical system, the system exhibits the same dynamics. To understand this, we turn back to the initial system (2). Here, we take the transformation: $u\to u-n$, which does not change the system equation but only leaves an additional constant in the first equation:

$$\{\begin{array}{l}\dot{x}=-ay-xz-u+n,\\ \dot{y}=-cx+xz,\\ \dot{z}=-b-mxy,\\ \dot{u}=kx-y.\end{array}$$

(6)

When changing the variable u with $u-n$ (n is a constant), system (2) gives the same dynamics. Therefore, if the variable u does not show in the other equations in system (2), the introduced constant will give a boosting control of the variable u. The chaotic signal u(t) can be revised from unipolar to bipolar or vice versa.

When a = 5, b = 4, c = 1, k = 0.5 and m = 1, the signal u is boosted from a bipolar to a unipolar one, which is indicated by the red and blue attractors in Figure 12a. The waveform of chaotic signal u(t) is shown in Figure 12b. The change of parameter n causes the up and down translation of the signal u(t). Some monostable systems have relatively large areas of basins of attraction; therefore, the initial conditions do not need to modify according to the variable which makes the offset control simpler, as shown in Figure 13.

Here the offset of the variable u is boosted along the u-axis according to the constant n. When n is positive, u is moved in the positive direction, and negative n causes the opposite direction. When the boosting controller n is changed from −30 to 30, system (6) has the same Lyapunov exponents, which is shown in Figure 13. The average value of variable u changes linearly with the increase of parameter n, while others remain unchanged.

3.5. Mixed Geometric Control

More striking, parameter c almost has a positive correlation with the offset of signal z, almost without changing other signals, and also has a negative correlation with the amplitude of variable x and positive correlation with the amplitude of variable y. Figure 14 shows the typical phase trajectories and waveforms. Figure 15 shows the corresponding Lyapunov exponent spectra and average value of the x, y and z signals. Therefore, all in all, there are five parameters, a, b, c, m and n, rescaling the system variables, some of which are restricted in a specific region, as shown in

Table 2. Five independent parameters in system (2) for geometric control.

Parameters	Execution Interval	Amplitude Control	Frequency Control	Offset Control
a	[6.9, 23.3]	positive control with x	positive	no
b	[3, 13]	positive control with x, y, z, u	positive	no
c	[10, 50]	positive control with y negative control with x	no	z
m	[0.1, 5]	Positive control with x, y, u	no	no
n	[−30, 30]	no	no	u

.

4. Bistability Analysis

In all the above analysis, we did not consider the multistability in each issue to simplify the demonstration. In fact, for the special structure of symmetry, coexisting attractors exist in their own basins of attraction in phase space. Specifically, for symmetrical systems, when the symmetry is broken, a pair of symmetrical coexisting attractors usually show up.

System (2) is a rotational symmetric system, which can be proved by the invariance of transformation $x\to -x,y\to -y,z\to z,u\to -u$. Symmetric systems are prone to show multistability due to the effect of broken symmetry. In general, predicting multistability seems not easy in theory. A common method to identify multistability is using the basins of attraction based on the ergodic initial conditions. Alternative methods can resort to non-bifurcation manipulation, in which a linear transformation is performed on the basin of attraction to generate a dynamical dispersion for a fixed initial condition, which can reveal different coexisting symmetrical pairs by generating different average values [40].

When offset boosting is introduced from the variables x and u,

$$\{\begin{array}{l}\dot{x}=-ay-(x+d)z-(u-d),\\ \dot{y}=(z-c)(x+d),\\ \dot{z}=-b-m(x+d)y,\\ \dot{u}=k(x+d)-y.\end{array}$$

(7)

and the average values of variables x and u will change according to the offset control parameter d. The coexisting attractors are drawn into different areas of the basin since the basins of attraction of the coexisting symmetric pair of attractors also change according to the offset parameter, as shown in Figure 16. In Figure 16a, the averages of variables x and u are revised by the offset parameters, while the average values of variable y remains the same. From Figure 16b, the invariance of Lyapunov exponents indicates the same structure of the symmetric pair of coexisting attractors. The typical phase trajectories of the symmetrical attractors of the system (2) under a pair of opposite initial conditions are shown in Figure 17.

To further verify the multistability in system (2), the basin of attraction is shown in Figure 18, which has the predicted symmetry and complex fractal structure. To show the types of attractors more clearly and comprehensively, the similar chaotic attractors are presented using an identical color in the basin of attraction. It can be clearly seen that there are two areas in different colors in the basin. The corresponding Lyapunov exponents of the two attractors are (0.2137, 0.0623, 0, -1.5761), and the Kaplan-Yorke dimension is 3.1751.

Both chaotic and hyperchaotic attractors show sensitivity to the initial condition, and furthermore, multistability and hyperchaos make the sensitivity more complicated. From two initial conditions in the same basin of attraction, even a slight difference results in great divergence in system (2), which is shown in Figure 19a. While from the two initial conditions in different basins of attraction, the slight difference leads to two separate phase trajectories, as shown in Figure 19b.

5. Circuit Implementation

The analog circuit of system (2) is designed as shown in Figure 20 with the circuit equation:

$$\{\begin{array}{l}\dot{x}=-\frac{1}{R_1{C}_1}y-\frac{1}{R_2{C}_1}xz-\frac{1}{R_3{C}_1}u\\ \dot{y}=-\frac{1}{R_4{C}_2}x+\frac{1}{R_5{C}_2}xz\\ \dot{z}=-\frac{1}{R_6{C}_3}+\frac{1}{R_7{C}_3}xy\\ \dot{u}=\frac{1}{R_8{C}_4}x-\frac{1}{R_9{C}_4}y\end{array}$$

(8)

Totally, the hyperchaotic circuit consists of four channels, which contain the integration, addition, subtraction, and nonlinear operations. The circuit is powered by 18V. The variables x, y, z and u in system (2) are the state voltages of the capacitors in four channels. The corresponding circuit element parameters can be selected as $C_1=C_2=C_3=C_4=10nF$, $R_2=R_5=R_7=4k\Omega$, $R_3=R_4=R_9=40k\Omega$, $R_1=8k\Omega$, $R_6=100k\Omega ,R_8=80k\Omega ,R_{10}=R_{11}=10k\Omega$. Here, a common time scale of 1000 is applied for better demonstration in the oscilloscope. The phase trajectories in circuit (8) under amplitude control are shown in Figure 21. Circuit experiment proves that the parameter m rescales the amplitude of x, y and u. Symmetric attractors are shown in Figure 22.

6. Discussion and Conclusions

A hidden hyperchaotic attractor is found, which has the property of amplitude control and offset boosting. The proposed system shares a symmetric structure, where one can find an independent knob for amplitude control. An extra introduced dimension leaves an opportunity for attractor shifting in phase space by an independent controller. Broken symmetry induced bistability is also well addressed in this work. All the coexisting symmetric attractors governed by the basin of attraction can be rescaled by the non-bifurcation parameter. Numerical and circuit simulation agree with each other proving the properties found in the hyperchaotic system.