Next Article in Journal
Effect of Stabilized Martensite on the Long-Term Performance of Superelastic NiTi Endodontic Files
Next Article in Special Issue
Radionuclides’ Recovery from Seawater Using FIC and FIC A Sorbents
Previous Article in Journal
Influence of Different Build Orientations and Heat Treatments on the Creep Properties of Inconel 718 Produced by PBF-LB
Previous Article in Special Issue
Synthetic Calcium Silicate Biocomposite Based on Sea Urchin Skeleton for 5-Fluorouracil Cancer Delivery
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

7Be Recovery from Seawater by Sorbents of Various Types

by
Nikolay A. Bezhin
1,2,
Iuliia G. Shibetskaia
1,
Ol’ga N. Kozlovskaia
1,
Evgeniy V. Slizchenko
1 and
Ivan G. Tananaev
2,3,4,*
1
Department of Biogeochemistry, Marine Hydrophysical Institute, Russian Academy of Sciences (MHI RAS), Kapitanskaya Str., 2, 299011 Sevastopol, Russia
2
Department of Chemistry and Chemical Engineering, Sevastopol State University, Universitetskaya Str., 33, 299053 Sevastopol, Russia
3
Radiochemistry Laboratory, Vernadsky Institute of Geochemistry and Analytical Chemistry of the Russian Academy of Sciences (GEOKHI RAS), Kosygin Str., 19, 119991 Moscow, Russia
4
Department of Nuclear Technology, Far Eastern Federal University, Sukhanov Str., 8, 690091 Vladivostok, Russia
*
Author to whom correspondence should be addressed.
Materials 2023, 16(11), 4088; https://doi.org/10.3390/ma16114088
Submission received: 16 April 2023 / Revised: 19 May 2023 / Accepted: 29 May 2023 / Published: 31 May 2023

Abstract

:
For the first time, a comprehensive study of sorbents based on manganese dioxide was carried out for beryllium sorption from seawater in laboratory and expeditionary conditions. The possibility of using several commercially available sorbents based on manganese dioxide (Modix, MDM, DMM, PAN-MnO2) and phosphorus(V) oxide (PD) for 7Be recovery from seawater for solving oceanological problems was evaluated. Beryllium sorption under static and dynamic conditions was studied. The distribution coefficients and dynamic and total dynamic exchange capacities were determined. Sorbents Modix (Kd = (2.2 ± 0.1) × 103 mL/g) and MDM (Kd = (2.4 ± 0.2) × 103 mL/g) showed high efficiency. The dependences of the degree of recovery on time (kinetics) and the capacity of the sorbent on the beryllium equilibrium concentration in solution (isotherm) were established. The data obtained were processed using kinetic models (intraparticle diffusion, pseudo-first and pseudo-second orders, Elovich model) and sorption isotherm equations (Langmuir, Freindlich, Dubinin–Radushkevich). The paper contains results of expeditionary studies to evaluate the sorption efficiency of 7Be from large volumes of the Black Sea water by various sorbents. We also compared the sorption efficiency of 7Be for the considered sorbents with aluminum oxide and previously obtained sorbents based on iron(III) hydroxide.

1. Introduction

The cosmogenic isotope 7Be forms in the Earth’s atmosphere under the action of fast protons; the main reaction of formation is 14N(p,2α)7Be. It is a constituent of BeO and Be(OH)2 compounds. These molecules diffuse through the atmosphere until they are sorbed by aerosol particles or captured by raindrops [1,2]. After that, 7Be enters the underlying surface, including the world ocean, mainly with atmospheric precipitation.
In oceanological studies, 7Be is widely used to study the processes of vertical transport in the ocean’s surface layer [3]. The results of several works [4,5] showed that the vertical distribution of 7Be generally reflects the temperature profile: the concentration of 7Be in the mixed layer is constant, while in the layers below the thermocline, it decreases exponentially. However, searching for materials that allow the most efficient concentration of 7Be from seawater is essential because the 7Be activity in seawater is only 1–12 Bq/m3, according to works [6,7,8].
Aluminum oxide was the first material proposed by W.B. Silker [9] for 7Be recovery from seawater. At high seawater flow rates (about 10 C.V./min (column volumes per minute)), the sorption efficiency of 7Be is less than 60%; however, reliable determination of 7Be activity on the second adsorber and the sorption efficiency becomes possible. This method was successfully used in works [5,8], and according to the data obtained, a mathematical model of 7Be distribution in the surface layer of the Black Sea was built [10].
To recover 7Be from seawater, most researchers widely use sorbents based on Fe(OH)3 and acrylate fiber [3] or polypropylene cartridges [7,11], which have shown a high sorption efficiency of 7Be. In particular, for the filtration and concentration system used in [7] based on cartridges impregnated with Fe(OH)3, when passing 4400–5500 L of seawater at a rate of 18.3–29.4 L/min, the radiochemical yield during beryllium sorption was 84.2–91.0%. However, this system was not widely used due to the need to keep the research vessel at the station for taking one sample for 3 to 5 h, while to get a vertical profile, the required sampling time increased by multiplying the number of points in the profile. In addition, polypropylene cartridges have a high hydrodynamic resistance, which can lead to the failure of pumping equipment.
Previously, we obtained several sorbents based on PAN (polyacrylonitrile) fiber and iron(III) hydroxide for the sorption of natural and cosmogenic radionuclides from seawater [10,11]. Their comprehensive study was carried out, the distribution coefficients of beryllium, the dynamic (DEC) and total dynamic exchange capacities (TDEC) of sorbents for beryllium were determined, output sorption curves were constructed [12], and the sorption kinetics and isotherm were studied [13]. The obtained sorbents were tested for radionuclides sorption from seawater [12]. In addition, the parameters of beryllium sorption by obtained sorbents based on PAN fiber and iron(III) hydroxide were compared with aluminum oxide [12,13]—the first material proposed for 7Be recovery [9].
However, some works [14,15,16] mention the possibility of recovering 7Be from seawater using sorbents based on manganese dioxide. Thus, it was proposed to recover beryllium with several sorbents based on manganese dioxide from artificial seawater [14,15]. Under static conditions at V/m = 1000 mL/g, high distribution coefficients of 7Be (Kd > 103 mL/g) were obtained on MnO2 impregnated on an anion exchange resin Biorad AG 1-X4 Cl form, biogenic MnO2, and nanostructured mesoporous MnO2.
7Be sorption from seawater was evaluated on model particles simulating various types of particulate matter, including MnO2. High values of 7Be sorption were obtained—97 ± 3% [16].
Thus, it is clearly seen that, at present, a small number of materials have been studied for the sorption of 7Be from seawater. Most researchers use either aluminum oxide [7] or sorbents based on iron(III) hydroxide [1].
Therefore, to find the optimal sorbent for recovering 7Be from seawater, it was necessary to evaluate the possibility of using commercially available sorbents based on manganese dioxide. Previously, we studied sorbents of this type in detail and characterized them concerning strontium [17,18] and radium isotopes [19] when recovered from seawater.
This work aims to conduct a comprehensive study of the sorption and kinetic characteristics of sorbents based on manganese dioxide and phosphorus(V) oxide for beryllium sorption from seawater. In addition, during our research work, we also needed to compare the sorption efficiency of these sorbents with the previously studied sorbents based on iron(III) hydroxide and aluminum oxide in 7Be sorption from large volumes of seawater under expeditionary conditions.

2. Materials and Methods

2.1. Materials

Table 1 shows detailed characteristics of the used sorbents based on manganese dioxide and phosphorus(V) oxide [17].
Beryllium sulfate (analytically pure grade) produced by AO ReaKhim (Moscow, Russia) was used as an additive.
Aluminon (analytically pure grade), ammonium acetate (analytically pure grade), disodium salt of ethylenediaminetetraacetic acid (analytically pure grade) produced by JSC ReaKhim (Moscow, Russia), and gum arabic produced by Alland & Robert S.A. (Port-Mort, France) were used to determine the concentration of stable beryllium.
For the preparation of calibration solutions, a standard sample of beryllium solution ISS (interstate standard sample) 0352:2002 (LLC Ormet, Ekaterinburg, Russia) was used.

2.2. Determination of Beryllium Distribution Coefficients

The distribution coefficients of beryllium were determined according to the unified method proposed in [20]. For this purpose, 20 mL of the test solution was added to 0.1 g of the sorbent. Sea water with the addition of beryllium to a concentration of 0.3 mg/L was used as the test solution. The resulting mixture was kept for 48 h with occasional stirring, then separated by filtration. Each experiment was repeated at least three times.

2.3. Sorption Dynamics

To study the dynamics of sorption through a column filled with 3 g of the sorbent, seawater with the addition of beryllium 0.3 mg/L was passed at different rates (3, 6, 15, 30 mL/min) using a LongerPump WT600-2J peristaltic pump (Longer Precision Pump Co., Baoding, China). After certain time intervals, a portion of the eluate was taken to estimate the number of beryllium ions that had not been sorbed. Each experiment was repeated at least three times for each rate.

2.4. Sorption Kinetics

The dependence of the degree of beryllium recovery on the time of sorption was determined by mixing 0.1 g of the sorbent with 10 mL of seawater with the addition of beryllium 0.3 mg/L for various times from 1 to 48 h. Then, the mixture was separated by filtration. Each experiment was repeated at least three times for each time point.

2.5. Sorption Isotherm

Determination of the dependence of the capacity of sorbents on the equilibrium concentration of beryllium in solutions was carried out by mixing 0.1 g of the sorbent with 10 mL of seawater with various additions of beryllium for 48 h. Then, the mixture was separated by filtration. Each experiment was repeated at least three times for each concentration.

2.6. Determination of the Concentration of Beryllium in Solution and Quantitative Parameters of Sorption

The beryllium concentration in solutions before and after sorption was determined using a KFK-3-01 photometer (JSC Zagorsk Optical and Mechanical Plant, Sergiev Posad, Russia) according to the method [21]. For this purpose, an aluminon solution was prepared by dissolving 0.5 g of aluminon, 140 g of ammonium acetate, and 10 g of gum arabic in distilled water, after which the volume of the solution was brought up to 1 L with distilled water. The resulting solution was filtered. A total of 5 mL of the disodium salt of ethylenediaminetetraacetic acid solution (5 g in 100 mL of water) and 10 mL of aluminon solution were added to 25 mL of the analyzed solution in a 50 mL volumetric flask. The mixture was heated for 10 min in a water bath, quickly cooled to room temperature (under cold water flow), and diluted with distilled water to the mark. Standard solutions with beryllium concentrations of 0.1, 0.2, and 0.4 mg/L were prepared using ISS Be 0352:2002 and with the same reagents as the analyzed samples. Optical density was measured at 536 nm in a 2 cm cuvette using a blank sample prepared with reagents, as well as the analyzed samples. The relative error in the determination of beryllium was 2–4%.
The distribution coefficient (Kd, mL/g), the degree of recovery (R, %), the sorbents capacity (q, mg/g), and the dynamic (DEC, mg/g) and total dynamic exchange capacity (TDEC, mg/g) were determined by the equations given in the articles [12,17].

2.7. Sorption of 7Be from Large Volumes of Seawater

Seawater sampling was carried out in the Black Sea during the 116 cruises (22 April–17 May 2021) of the R/V Professor Vodyanitsky using a UNIPUMP BAVLENETS BV 0.12-40-U5 submersible vibration pump (LLC Subline Service, Moscow, Russia) into plastic tanks located on board. In the process of sampling, for separation of suspended matter, the sample was filtered through 5 inches high polypropylene cartridges with a pore size of 0.5 µm FCPS1M series (Aquafilter Europe Ltd., Lodz, Poland) at a rate of 6–10 L/min. A high filtration rate is necessary since the prefilter saturated with suspended matter acts as a “sorbent” for several radionuclides, in particular 7Be, which misrepresents the results of its initial activity in dissolved and suspended form.
Sorption of 7Be from large volumes of seawater was performed using single-column and two-column methods.
The one-column method consisted in adding stable beryllium as a tracer to the seawater sample to a concentration of 0.3 mg/L. 5–6 h later, when the concentration of beryllium was equalized in the entire volume of the container, the sample was passed through one column with the studied sorbent. In this case, every 10–50 L, a sample of the passed seawater was taken to analyze the concentration of stable beryllium in it for further evaluation of the sorption efficiency using the equation given in [22,23]:
E = V C 0 V p C p V C 0 100 %
where C0 is the initial cesium concentration, mg/L; V is the total volume of seawater passed through the sorbent, L; Cp is the cesium concentration in a portion of seawater passed through the sorbent, mg/L; and Vp is the volume of a portion of seawater passed through the sorbent, L.
The two-column method consisted of passing seawater samples through two successively installed columns with studied sorbent of the same volume. The sorption efficiency was determined by the equation given in [24]:
E = 1 B A
where A and B are the activities of the radionuclide on the sorbent in the first and second adsorbers.
The disadvantage of the method is a significant error due to the low activity of the extracted radionuclide on the second sorbent.
The sample volume for extracting 7Be ranges from 250 to 1000 L and depends on the time interval between the concentration and sample measurement since the half-life of 7Be is only 53.3 days. In a long expedition, the time interval between concentration and measurement of the samples can be more than a month, and then larger samples are needed.
After 7Be concentration, the sorbents were dried in a SNOL 58/350 I4 oven (AB UMEGA-GROUP, Utena, Lithuania) at a temperature of 70–80 °C. When using fibrous sorbents, after drying, the sorbent was additionally ashed in a SNOL-30/1300-I1p muffle furnace (AB UMEGA-GROUP, Utena, Lithuania) at 700 °C for 8 h to reduce the volume of the counting sample and as a consequence, self-absorption of gamma radiation.

2.8. Determination of 7Be Activity in Sorbents

7Be activity in the sorbents was determined by the 477 keV (10.44%) photopeak [25] on a Canberra multichannel gamma spectrometer for measuring X-ray and gamma radiation (Canberra Industries, Meriden, CT, USA) with Canberra BE3825 Broad Energy High Purity Germanium Detector for at least 24 h. In this case, the relative error measurement was 13–16%. Detection efficiency was estimated using ISOCS/LabSOCS software (Canberra Industries, Meriden, CT, USA).

3. Results and Discussion

3.1. Beryllium Distribution Coefficients

Table 2 shows the determined distribution coefficients of beryllium from seawater by the studied sorbents.
It is clear that beryllium is more effectively sorbed on MDM and Modix sorbents. In general, the sorbents under study can be arranged in the following order in terms of the beryllium distribution coefficient:
MDM ≈ Modix > PAN-MnO2 > PD ≈ DMM.
For beryllium, the distribution coefficients obtained on sorbents on manganese dioxide are generally higher than the distribution coefficients obtained in our study [12] on sorbents based on iron(III) hydroxide. For example, among the sorbents of this type, the best distribution coefficient of beryllium was obtained on the Fe-SF sorbent (Fe-Sodium Ferrate, obtained using ready-made Na2FeO4) and amounted to (1.1 ± 0.1)×103 mL/g (Table S1).
These results are due to the fact that Modix and MDM sorbents are granular manganese dioxide, differing only in particle size: 0.16–0.3 mm and 0.2–3.0 mm, respectively. At the same time, the other sorbents under consideration, including those based on iron hydroxide (III), consist of a carrier on which an active component is applied; its content in the finished sorbent varies from 5 to 22% (Table 1).

3.2. Sorption Dynamics

Figure 1 shows beryllium recovery output curves obtained at various seawater flow rates.
The shapes of the output curves clearly show that the Modix sorbent has higher capacity characteristics. A more S-shaped output curve is characteristic of sorbents with higher values of exchange capacity; a more convex output curve indicates low values of exchange capacity.
Table 3 shows the obtained values of DEC and TDEC.
The DEC and TDEC of the Modix sorbent were higher than these of the other sorbents. In general, the studied sorbents can be arranged in the following order in terms of DEC and TDEC:
Modix > MDM > PAN-MnO2 > DMM > PD.
The DEC and TDEC values of the previously studied sorbents based on iron(III) hydroxide [12] were generally lower than the values obtained for the Modix sorbent. In particular, the best Fe-H sorbent (Fe-Hydrolyzed, obtained using pre-hydrolyzed PAN with precipitation of Fe(OH)3 by ammonia) in terms of these characteristics at a seawater flow rate of 3 mL/min had somewhat lower DEC and TDEC values of 0.068 and 0.656 mg/g (Table S1), respectively [12].

3.3. Sorption Kinetics

Figure 2 shows the results of determining the dependence of the degree of recovery of beryllium on the time of sorption.
It is clear that the studied sorbents reach the time sorption equilibrium within 40–48 h, which corresponds to the data on the sorption kinetics on aluminum oxide and sorbents on iron(III) hydroxide, except the Fe-H sorbent, which extracts beryllium in 10 min [13].
The obtained data were processed using four kinetic models: pseudo-first [26,27,28,29] and pseudo-second [26,27,28,30] orders, intraparticle diffusion [26,30], and the Elovich model [27,28,31].
The obtained experimental values of the equilibrium capacity of the sorbents correspond to the values obtained by the pseudo-second-order equation (Table 4).
The acquired parameters of the kinetic models generally correspond to the parameters obtained on sorbents based on iron(III) hydroxide [13] and are well described using the pseudo-second-order model, which makes it possible to take into account not only sorbate–sorbent interactions, but also intermolecular interactions of adsorbed substances. Thus, the chemical exchange reaction limits the sorption process [26,27,30].
In general, changes in the sorption rate constants of the models pseudo-first (K1) and pseudo-second-order (K2) and Elovich model (α) have common patterns for sorbents based on MnO2:
Modix > PAN-MnO2 > MDM > DMM.

3.4. Sorption Isotherm

Figure 3 shows the determined dependences of the capacity of sorbents on the equilibrium concentration of beryllium in solutions. It is seen that the maximum beryllium capacity of sorbents is reached at an equilibrium beryllium concentration in a solution of more than 2 mg/L. The Modix sorbent (0.752 mg/g) has the highest beryllium capacity, which exceeds the maximum capacity previously obtained for the Fe-H sorbent (0.694 mg/g, Table S1) [13].
The obtained data were processed using the Langmuir [26,29,31], Freindlich [27,29,31], and Dubinin–Radushkevich [26,31,32,33] sorption equations.
The obtained experimental values of the maximum capacity of the sorbents correspond to the values obtained from the Langmuir isotherm equation (Table 5), which describes adsorption on a monomolecular layer well. Thus, the obtained data on the recovery of beryllium by all the studied sorbents are well described by the Langmuir sorption isotherm equation, which corresponds to the results obtained on sorbents based on iron(III) hydroxide [13].

3.5. Sorption of 7Be from Large Volumes of Seawater

Figure 4 shows the results of evaluating the sorption efficiency of 7Be from seawater samples of large volume by the studied sorbents in comparison with the sorbents based on iron(III) hydroxide and aluminum oxide presented in [12]. In our work [12], a detailed study of the sorption efficiency of 7Be by sorbents based on iron(III) hydroxide and aluminum oxide was not carried out; only the results of single tests were presented when 1000 L of seawater were passed through 2 columns of 100 g of the sorbent at a rate of 1 L/min.
According to the obtained results, the best efficiency of 7Be sorption from seawater is shown by Modix (E = 63.2–76.7%), MDM (E = 55.5–72.3%), and Fe-H (E = 60.9–78.5%) sorbents. The optimal seawater flow rate for 7Be sorption is 2–6 C.V./min. Examples of the obtained 7Be activities in the Black Sea water in the spring of 2021 when testing various sorbents at a seawater transmission rate of 2.4–3.2 C.V./min are given in Table S2.
Thus, these sorbents can be successfully used to solve the oceanological problem of estimating vertical transport [34,35].
In the course of laboratory tests, sorbents based on manganese dioxide proved to be more efficient in the recovery of beryllium compared to sorbents based on iron(III) hydroxide according to [12,13]; however, in the expeditionary studies, their efficiency is comparable to sorbents based on iron(III) hydroxide.
This is explained by the fact that sorbents based on manganese dioxide, in contrast to sorbents based on iron(III) hydroxide and also sorb radium isotopes from seawater quite efficiently [36,37,38,39,40].
Thus, sorbents based on manganese dioxide can be effectively used to recover such isotopes important for oceanological research [41] as 7Be, 210Pb [14,15,39,40], 210Po [14,15,40], “radium quartet” (223Ra, 224Ra, 226Ra, 228Ra) [36,37,38,39,40], 234Th [14,15,39] from seawater. The gamma spectrometric method makes it possible to determine the activity of most of these isotopes (7Be [25], 210Pb [42], 226Ra and 228Ra [43], 234Th [44]) from various peaks. Determination of 210Po is possible by the alpha spectrometric method [45] after radiochemical preparation; short-lived radium isotopes (223Ra, 224Ra) can be detected using the RaDeCC (Radium Delayed Coincidence Counter) system [46]. However, 226Ra can only be measured 3 weeks after hermetic sealing to achieve its equilibrium with 214Pb [43].
Moreover, it is possible effectively and reliably separate the peaks of beryllium and radium due to their superposition (Figures S1 and S2) only on gamma spectrometric equipment with HPGe detectors, which can be difficult for several laboratories with less efficient equipment.
Sorbents based on iron(III) hydroxide can be effectively used to recover such isotopes as 7Be [3,7,11,12,47], 32P, and 33P [7,11,12,47], 210Pb [12,48,49,50], 210Po [51], 234Th [12,47,50] from seawater. The isotopes 7Be [25], 210Pb [42], and 234Th [44] can be simultaneously analyzed on a gamma spectrometer using different peaks, and there are no problems in separating the peaks of thorium and radium, which makes it possible to use even scintillation gamma rays for effective analysis of 7Be and 234Th spectrometers. Analysis of 32P, 33P, and 210Po requires additional radiochemical preparation. Unfortunately, for a pair of phosphorus and 210Po isotopes, the radiochemical preparation is different, so their simultaneous analysis is not possible. After radiochemical preparation, 32P and 33P can be analyzed by beta spectrometry [52] and 210Po—by alpha spectrometry [45].
We assume that in the case of gamma-spectrometric determination of the activity of radionuclides in sorbent samples, it is most effective to carry out a complex extraction of radionuclides by sequentially arranging the first columns of sorbents based on iron(III) hydroxide and then columns of sorbents based on manganese dioxide. Thus, it will be possible to determine 7Be, 210Pb, and 234Th on a sorbent based on iron(III) hydroxide and 226Ra and 228Ra on the next sorbent based on manganese dioxide. We use this principle in the sequential arrangement of PAN-Fe(OH)3 and PAN-MnO2 sorbents in our new studies.
Despite high sorption efficiency, the Modix sorbent has a high hydrodynamic resistance due to the small size of the granules (0.16–0.3 mm). However, in expeditionary studies, to reduce the analysis time and increase the number of samples taken, it is important to achieve a high rate of seawater flowing through the sorbent. Therefore, at high seawater flow rates, sorbents with relatively large granules would be the best choice, even though they are less efficient, for example, MDM (granule size 1.0–3.0 mm). Fibrous sorbents modified with manganese dioxide or iron(III) hydroxide have low hydrodynamic resistance and proved good for the recovery of radionuclides in expeditionary studies.

4. Conclusions

Thus, sorbents based on manganese dioxide and phosphorus(V) oxide to extract 7Be from seawater can be used for solving the problems of oceanology. A comprehensive study of commercially available sorbents, from laboratory static and dynamic tests to expeditionary studies on large volumes of seawater, was carried out. The results obtained on sorbents based on manganese dioxide were compared with sorbents based on iron(III) hydroxide.
Experimental data on the distribution coefficients of beryllium on the studied sorbents and the values of dynamic and total dynamic exchange capacities were obtained. The obtained values for beryllium exceeded those for sorbents based on iron(III) hydroxide.
Isotherms, output, and kinetic curves of sorption were plotted. The obtained data were characterized using several sorption models. A pseudo-second-order kinetic model (r2 > 0.996) described well the determined dependences of the degree of recovery on the sorption time; the Langmuir sorption isotherm (r2 > 0.997) well described the dependence of the sorbent capacity on the equilibrium concentration of beryllium.
In tests on large volumes of seawater, the efficiency of sorbents based on manganese dioxide (E = 63.2–76.7% for Modix, E = 55.5–72.3% for MDM) was comparable to sorbents based on iron(III) hydroxide (E = 60.9–78.5% for Fe-H), which is explained by more efficient specific sorption of radium isotopes from seawater by sorbents based on manganese dioxide.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/ma16114088/s1, Figure S1. Gamma spectrum of a sorbent based on manganese dioxide, obtained by radionuclides sorption from seawater by a single-column method. Figure S2. Gamma spectra of sorbents based on iron(III) hydroxide, obtained by radionuclides sorption from seawater by a two-column method. Table S1. Parameters of beryllium sorption by sorbents based on iron(III) hydroxide and aluminum oxide. Table S2. Examples of the obtained 7Be activities in the Black Sea water in the spring of 2021 when testing various sorbents.

Author Contributions

Conceptualization, N.A.B. and I.G.T.; methodology, N.A.B. and I.G.S.; validation, N.A.B.; formal analysis, I.G.S., O.N.K. and E.V.S.; investigation, N.A.B., O.N.K. I.G.S. and E.V.S.; resources, N.A.B.; data curation, I.G.S., O.N.K. and E.V.S.; writing—original draft preparation, N.A.B., O.N.K. and I.G.T.; writing—review and editing, all authors; visualization, N.A.B. and I.G.S.; supervision, I.G.T.; project administration, N.A.B.; funding acquisition, I.G.T. All authors have read and agreed to the published version of the manuscript.

Funding

The research was funded within the framework of the project of the Sevastopol State University No. 42-01-09/169/2021-7 and the state task of the Ministry of Science and Higher Education of the Russian Federation (topic “Oceanological processes” No. FNNN-2021-0004).

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Sapozhnikov, Y.A.; Aliev, R.A.; Kalmykov, S.N. Radioactivity of the Environment; BINOM Knowledge Laboratory: Moscow, Russia, 2015; 289p. (In Russian) [Google Scholar]
  2. Hisao, N.; Wataru, T.; Takayuki, K. Prodaction Rates of 7Be and 10Be in the Atmosphere. Nucl. Instr. Methods Phys. Res. Sect. B Beam Interact. Mater. Atoms 2001, 172, 796–801. [Google Scholar] [CrossRef]
  3. Kadko, D.; Olson, D. Beryllium-7 as a tracer of surface water subduction and mixed-layer history. Deep Sea Res. Part I Oceanogr. Res. Pap. 1996, 43, 86–116. [Google Scholar] [CrossRef]
  4. Haskell, W.Z.; Kadko, D.; Hammond, D.E.; Knapp, A.N.; Prokopenko, M.G.; Berelson, W.M.; Capone, D.G. Upwelling velocity and eddy diffusivity from 7Be measurements used to compare vertical nutrient flux to export POC flux in the Eastern Tropical South Pacific. Mar. Chem. 2015, 168, 140–150. [Google Scholar] [CrossRef]
  5. Kremenchutskii, D.A. Distribution of beryllium-7 (7Be) in the Black Sea in the summer of 2016. Environ. Sci. Pollut. Res. 2018, 31, 31569–31578. [Google Scholar] [CrossRef]
  6. Venti, A.; Kadko, D.; Andersson, A.J.; Langdon, C.; Bates, N.R. A multi-tracer model approach to estimate reef water residence times. Limnol. Oceanogr. Methods 2012, 10, 1078–1095. [Google Scholar] [CrossRef]
  7. Nakanishi, T.; Kusakabe, M.; Aono, T.; Yamada, M. Simultaneous measurements of cosmogenic radionuclides 32P, 33P and 7Be in dissolved and particulate forms in the upper ocean. J. Radioanal. Nucl. Chem. 2009, 279, 769–776. [Google Scholar] [CrossRef]
  8. Kremenchutskii, D.A.; Batrakov, G.F.; Dovhyi, I.I.; Sapozhnikov, Y.A. Role of suspended matter in controlling beryllium-7 (7Be) in the Black Sea surface layer. Mar. Syst. 2021, 217, 10351. [Google Scholar] [CrossRef]
  9. Silker, W.B.; Robertson, D.E.; Rieck, H.G., Jr.; Perkins, R.W.; Prospero, J.M. Beryllium-7 in ocean water. Science 1968, 161, 879–880. [Google Scholar] [CrossRef]
  10. Kremenchutskii, D.A.; Dymova, O.A.; Batrakov, G.F.; Konovalov, S.K. Numerical simulation of the intra-annual evolution of beryllium-7 (7Be) in the surface layer of the Black Sea. Environ. Sci. Pollut. Res. 2018, 11, 11120–11127. [Google Scholar] [CrossRef]
  11. Aono, T.; Kusakabe, M.; Nakanishi, T.; Yamada, M.; Kancko, S.; Nakamura, T.; Hori, K.; Bishop, J.K.B. Large Volume in situ Filtration and Concentration System for Measurements of Low-level Radioactivity in Seawater. J. Adv. Mar. Sci. Technol. Soc. 2008, 14, 39–50. [Google Scholar] [CrossRef]
  12. Bezhin, N.A.; Frolova, M.A.; Dovhyi, I.I.; Kozlovskaia, O.N.; Slizchenko, E.V.; Shibetskaia, I.G.; Khlystov, V.A.; Tokar’, E.A.; Tananaev, I.G. The Sorbents Based on Acrylic Fiber Impregnated by Iron Hydroxide (III): Production Methods, Properties, Application in Oceanographic Research. Water 2022, 14, 2303. [Google Scholar] [CrossRef]
  13. Bezhin, N.A.; Frolova, M.A.; Kozlovskaya, O.N.; Slizchenko, E.V.; Shibetskaya, Y.G.; Tananaev, I.G. Physical and chemical regularities of phosphorus and beryllium recovery from the seawater by acrylate fiber based on iron(+3) hydroxide. Processes 2022, 10, 2010. [Google Scholar] [CrossRef]
  14. Athon, M.T.; Fryxell, G.E.; Chuang, C.-Y.; Santschi, P.H. Sorption of selected radionuclides on different MnO2 phases. Environ. Chem. 2017, 14, 207–214. [Google Scholar] [CrossRef]
  15. Athon, M.T. Chemisorption of Radionuclides on Commercial, Synthetic, and Biogenic Sorbents for Use In-Situ Gamma Spectrometry. Master’s Thesis, Texas A&M University, College Station, TX, USA, 2016. [Google Scholar]
  16. Yang, W.; Guo, L.; Chuang, C.-Y.; Schumann, D.; Ayranov, M.; Santschi, P.H. Adsorption characteristics of 210Pb, 210Po and 7Be onto micro-particle surfaces and the effects of macromolecular organic compounds. Geochim. Cosmochim. Acta 2013, 107, 47–64. [Google Scholar] [CrossRef]
  17. Bezhin, N.A.; Dovhyi, I.I.; Kapranov, S.V.; Bobko, N.I.; Milyutin, V.V.; Kaptakov, V.O.; Kozlitin, E.A.; Tananaev, I.G. Separation of radiostrontium from seawater using various types of sorbents. J. Radioanal. Nucl. Chem. 2021, 328, 1199–1209. [Google Scholar] [CrossRef]
  18. Bezhin, N.A.; Dovhyi, I.I.; Tokar, E.A.; Tananaev, I.G. Physical and chemical regularities of cesium and strontium recovery from the seawater by sorbents of various types. J. Radioanal. Nucl. Chem. 2021, 330, 1101–1111. [Google Scholar] [CrossRef]
  19. Kozlovskaia, O.N.; Shibetskaia, I.G.; Bezhin, N.A.; Tananaev, I.G. Estimation of 226Ra and 228Ra Content Using Various Types of Sorbents and Their Distribution in the Surface Layer of the Black Sea. Materials 2023, 16, 1935. [Google Scholar] [CrossRef] [PubMed]
  20. Nekrasova, N.A.; Milyutin, V.V.; Kaptakov, V.O.; Kozlitin, E.A. Inorganic Sorbents for Wastewater Treatment from Radioactive Contaminants. Inorganics 2023, 11, 126. [Google Scholar] [CrossRef]
  21. Korostelev, P.P. Photometric and Complexometric Analysis in Metallurgy; Metallurgy: Moscow, Russia, 1984. (In Russian) [Google Scholar]
  22. Kadko, D. Upwelling and primaryproduction during the U.S. GEOTRACES East Pacific Zonal Transect. Glob. Biogeochem. Cycles 2017, 31, 218–232. [Google Scholar] [CrossRef]
  23. Bezhin, N.A.; Kremenchutskii, D.A.; Slizchenko, E.V.; Kozlovskaia, O.N.; Shibetskaia, I.G.; Milyutin, V.V.; Tananaev, I.G. Estimation of 137Cs Distribution and Recovery Using Various Types of Sorbents in the Black Sea Surface Layer. Processes 2023, 11, 603. [Google Scholar] [CrossRef]
  24. Mann, D.R.; Casso, S.A. In situ chemisorption of radiocesium from seawater. Mar. Chem. 1984, 14, 307–318. [Google Scholar] [CrossRef]
  25. Andrews, J.E.; Hartin, C.; Buesseler, K.O. 7Be analyses in seawater by low background gamma-spectroscopy. J. Radioanal. Nucl. Chem. 2008, 277, 253–259. [Google Scholar] [CrossRef]
  26. Dong, L.; Wu, C.; Han, Y.; Pan, S.; Wang, Z.; Zhang, G.; Hou, L.; Gu, P. Research on the application potential of spent biological activated carbon from BAC process to remove radionuclides Sr2+ from water. J. Radioanal. Nucl. Chem. 2021, 327, 1179–1190. [Google Scholar] [CrossRef]
  27. Attallah, M.F.; Borai, E.H.; Allan, K.F. Kinetic and thermodynamic studies for cesium removal from low-level liquid radioactive waste using impregnated polymeric material. Radiochemistry 2009, 51, 622–627. [Google Scholar] [CrossRef]
  28. Dakroury, G.A.; Abo-Zahra, S.F.; Hassan, H.S. Utilization of olive pomace in nano MgO modification for sorption of Ni(II) and Cu(II) metal ions from aqueous solutions. Arab. J. Chem. 2020, 13, 6510–6522. [Google Scholar] [CrossRef]
  29. El-Shazly, E.A.A.; Dakroury, G.A.; Someda, H.H. Kinetic and isotherm studies for the sorption of 134Cs and 60Co radionuclides onto supported titanium oxide. J. Radioanal. Nucl. Chem. 2021, 330, 127–139. [Google Scholar] [CrossRef]
  30. Plazinski, W.; Dziuba, J.; Rudzinski, W. Modeling of Sorption Kinetics: The Pseudo-Second Order Equation and the Sorbate Intraparticle Diffusivity. Adsorption 2013, 19, 1055–1064. [Google Scholar] [CrossRef]
  31. Javadian, H. Application of kinetic, isotherm and thermodynamic models for the adsorption of Co(II) ions on polyamidine/polypyrrole copolymer nanofibers from aqueous solution. J. Ind. Eng. Chem. 2014, 20, 4233–4241. [Google Scholar] [CrossRef]
  32. Dubinin, M.M. The potential theory of adsorption of gases and vapors for adsorbents with energetically non-uniform surface. Chem. Rev. 1960, 60, 235–241. [Google Scholar] [CrossRef]
  33. Hu, Q.; Zhang, Z. Application of Dubinin–Radushkevich isotherm model at the sol-id/solution interface: A theoretical analysis. J. Mol. Liq. 2019, 277, 646–648. [Google Scholar] [CrossRef]
  34. Chukharev, A.M.; Pavlov, M.I. Model and Experimental Estimates of Vertical Mixing Intensity in the Sea Upper Homogeneous Layer. Phys. Oceanogr. 2021, 28, 309–325. [Google Scholar] [CrossRef]
  35. Samodurov, A.S.; Chukharev, A.M.; Kazakov, D.A. Basic Regularities of Vertical Turbulent Exchange in the Mixed and Stratified Layers of the Black Sea. Phys. Oceanogr. 2021, 28, 376–391. [Google Scholar] [CrossRef]
  36. Moon, D.S.; Burnett, W.C.; Nour, S.; Horwitz, P.; Bond, A. Preconcentration of radium isotopes from natural waters using MnO2 resin. Appl. Rad. Isot. 2003, 59, 255–262. [Google Scholar] [CrossRef]
  37. Henderson, P.B.; Morris, P.J.; Moore, W.S.; Charette, M.A. Methodological advances for measuring low-level radium isotopes in seawater. J. Radioanal. Nucl. Chem. 2013, 296, 357–362. [Google Scholar] [CrossRef]
  38. Charette, M.A.; Dulaiova, H.; Gonneea, M.E.; Henderson, P.B.; Moore, W.S.; Scholten, J.C.; Pham, M.K. GEOTRACES radium isotopes interlaboratory comparison experiment. Limnol. Oceanogr. Methods 2012, 10, 451–463. [Google Scholar] [CrossRef]
  39. Colley, S.; Thomson, J. Particulate/solution analysis of 226Ra, 230Th and 210Pb in sea water sampled by in-situ large volume filtration and sorption by manganese oxyhydroxide. Sci. Total Environ. 1994, 155, 273–283. [Google Scholar] [CrossRef]
  40. Towler, P.H.; Smith, J.D.; Dixon, D.R. Magnetic recovery of radium, lead and polonium from seawater samples after preconcentration on a magnetic adsorbent of manganese dioxide coated magnetite. Anal. Chim. Acta 1996, 328, 53–59. [Google Scholar] [CrossRef]
  41. Dovhyi, I.I.; Bezhin, N.A.; Tananaev, I.G. Sorption methods in marine radiochemistry. Rus. Chem. Rev. 2021, 90, 1544–1565. [Google Scholar] [CrossRef]
  42. Yücel, M.; Moore, W.S.; Butler, I.B.; Boyce, A.; Luther, G.W. Recent sedimentation in the Black Sea: New insights from radionuclide distributions and sulfur isotopes. Deep Sea Res. Part I Oceanogr. Res. Pap. 2012, 66, 103–113. [Google Scholar] [CrossRef]
  43. Dulaiova, H.; Burnett, W.C. An efficient method for γ-spectrometric determination of radium-226,228 via manganese fibers. Limnol. Oceanogr. Methods 2004, 2, 256–261. [Google Scholar] [CrossRef]
  44. Gulin, S.B. Seasonal changes of 234Th scavenging in surface water across the western Black Sea. An implication of the cyclonic circulation patterns. J. Environ. Radioact. 2000, 51, 335–347. [Google Scholar] [CrossRef]
  45. Villa-Alfageme, M.; Mas, J.L.; Hurtado-Bermudez, S.; Masqué, P. Rapid determination of 210Pb and 210Po in water and application to marine samples. Talanta 2016, 160, 28–35. [Google Scholar] [CrossRef] [PubMed]
  46. Moore, W.S.; Arnold, R. Measurement of 223Ra and 224Ra in coastal waters using a delayed co-incidence counter. J. Geophys. Res. 1996, 101, 1321–1329. [Google Scholar] [CrossRef]
  47. Lee, T.; Barg, E.; Lal, D. Studies of vertical mixing in the Southern California Bight with cosmogenic radionuclides 32P and 7Be. Limnol. Oceanogr. 1991, 36, 1044–1052. [Google Scholar] [CrossRef]
  48. Suriyanarayanan, S.; Brahmanandhan, G.M.; Malathi, J.; Ravi Kumar, S.; Masilamani, V.; Shahul Hameed, P.; Selvasekarapandian, S. Studies on the distribution of 210Po and 210Pb in the ecosystem of Point Calimere Coast (Palk Strait), India. J. Environ. Radioact. 2008, 99, 766–771. [Google Scholar] [CrossRef]
  49. Suriyanarayanan, S.; Brahmanandhan, G.M.; Samivel, K.; Ravikumar, S.; Shahul Hameed, P. Assessment of 210Po and 210Pb in marine biota of the Mallipattinam ecosystem of Tamil Nadu, India. J. Environ. Radioact. 2010, 101, 1007–1010. [Google Scholar] [CrossRef]
  50. Krishnaswami, S.; Lal, D.; Somayajulu, B.L.K.; Dixon, F.S.; Stonecipher, S.A.; Craig, H. Silicon, radium, thorium, and lead in seawater: In-situ extraction by synthetic fibre. Earth Planet. Sci. Lett. 1972, 16, 84–90. [Google Scholar] [CrossRef]
  51. Iyengar, M.A.R.; Thulasi Brindha, A.P. Polonium-210 measurements in coastal sea waters using ferric hydroxide coated polyacrylic fibres. Radiat. Prot. Environ. 1997, 20, 57–60. [Google Scholar]
  52. Benitez-Nelson, C.R.; Buesseler, K.O. Measurement of cosmogenic 32P and 33P activities in rainwater and seawater. Anal. Chem. 1998, 70, 64–72. [Google Scholar] [CrossRef]
Figure 1. Beryllium sorption output curves at different flow rates (3, 6, 15, and 30 mL/min) on the sorbents: (a) Modix; (b) MDM; (c) DMM; (d) PAN-MnO2; (e) PD.
Figure 1. Beryllium sorption output curves at different flow rates (3, 6, 15, and 30 mL/min) on the sorbents: (a) Modix; (b) MDM; (c) DMM; (d) PAN-MnO2; (e) PD.
Materials 16 04088 g001
Figure 2. Kinetic curves of beryllium sorption.
Figure 2. Kinetic curves of beryllium sorption.
Materials 16 04088 g002
Figure 3. Sorption isotherms of beryllium.
Figure 3. Sorption isotherms of beryllium.
Materials 16 04088 g003
Figure 4. Sorption efficiency of 7Be from large volumes of seawater by sorbents of various types.
Figure 4. Sorption efficiency of 7Be from large volumes of seawater by sorbents of various types.
Materials 16 04088 g004
Table 1. Characteristics of the sorbents used for beryllium separation.
Table 1. Characteristics of the sorbents used for beryllium separation.
SorbentManufacturerAppearanceGrain Size, mmBulk Weight, g/mLSorbent Composition
SupportSorption-Active Phase: Content, Mass %
ModixSPE Eksorb Ltd. (Ekaterinburg, Russia)Irregular-shaped black granules0.16–0.30.6–0.9manganese dioxide
MDMSPE Ektos-Atom, JSC (Moscow, Russia)Irregular-shaped dark brown granules0.1–3.00.4–0.6manganese oxides (III, IV)
DMMIrregular-shaped dark brown granules0.1–5.00.1–0.4cellulosemanganese oxides (III, IV); not less than 5
PDIrregular-shaped light brown granules0.1–5.00.1–0.4phosphorylated woodphosphorus(V) oxide; not less than 13
PAN-MnO2black fiberPAN fibermanganese dioxide; 18–22
Table 2. Beryllium distribution coefficients.
Table 2. Beryllium distribution coefficients.
SorbentModixMDMDMMPAN-MnO2PD
Kd, mL/g(2.2 ± 0.1) × 103(2.4 ± 0.2) × 103700 ± 50(1.5 ± 0.1) × 103850 ± 90
Table 3. DEC and TDEC of sorbents for beryllium.
Table 3. DEC and TDEC of sorbents for beryllium.
SorbentFlow Rate, mL/min
361530
DEC, mg/gTDEC, mg/gDEC, mg/gTDEC, mg/gDEC, mg/gTDEC, mg/gDEC, mg/gTDEC, mg/g
Modix0.1250.7390.0930.6370.0620.5410.0420.470
MDM0.0620.4600.0420.4070.0210.3460.0100.298
DMM0.0420.2950.0310.2670.0160.2340.0060.171
PAN-MnO20.0520.3780.0350.3340.0180.2840.0080.266
PD0.0310.2290.0210.1800.0120.1570.0040.135
Table 4. Parameters of kinetic models.
Table 4. Parameters of kinetic models.
SorbentIntraparticle Diffusion *Pseudo-First-
Order *
Pseudo-Second-Order *Elovich Model *qe exp, mg/g
KI, mg/(g∙h0.5)c, mg/gr2K1, h−1ge, mg/gr2K2, g/(mg∙h)ge, mg/gr2α, g/(mg∙h)β, g/mgr2
Modix0.00190.01290.9330.1080.01320.98018.30.02590.9980.1363130.9740.0247
MDM0.00230.01030.9650.0930.01580.97311.80.02640.9960.0652700.9750.0249
DMM0.00230.00860.9540.0830.01420.98812.00.02420.9960.0392700.9920.0228
PAN-MnO20.00240.00980.9040.1040.01560.99113.80.02570.9990.0442500.9940.0243
PD0.00210.01030.9300.0900.01320.99015.30.02450.9980.0662860.9970.0233
* KI is the rate constant of intraparticle diffusion, mg/(g∙h0.5); c is the constant characterizing the contribution of the boundary layer, mg/g; qe is the equilibrium capacity of the sorbent, mg/g; K1 is the pseudo-first-order rate constant, h−1; K2 is the pseudo-second-order rate constant, g/(mg∙h); α is the initial sorption rate constant, g/mg h; β is the desorption constant, g/mg; r2 is the approximation confidence factor.
Table 5. Parameters of sorption isotherms.
Table 5. Parameters of sorption isotherms.
SorbentLangmuir Isotherm *Freindlich Isotherm *Dubinin–Radushkevich Isotherm *qm exp, mg/g
qm, mg/gKL, L/mgr2KF, mg/gnr2qm, mg/gβ, mol2/kJ2E, kJ/molr2
Modix0.7612.910.9970.6461.500.9561.010.01386.020.9960.752
MDM0.5301.950.9990.3141.600.9630.6000.01525.740.9970.521
DMM0.3232.580.9990.1861.940.9520.3530.01356.090.9980.321
PAN-MnO20.4151.830.9990.2151.750.9630.4410.01525.740.9980.410
PD0.2562.070.9990.1361.960.9540.2720.01465.850.9990.254
* qm is the maximum capacity of the sorbent, mg/g; KL is the Langmuir adsorption equilibrium constant, L/mg; KF is the Freundlich constant, mg/g; n is the empirical indicator of the heterogeneity of exchange centers; β is the constant associated with sorption energy, mol2/kJ2; E is the average free energy of sorption, kJ/mol; r2 is the approximation confidence factor.
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Bezhin, N.A.; Shibetskaia, I.G.; Kozlovskaia, O.N.; Slizchenko, E.V.; Tananaev, I.G. 7Be Recovery from Seawater by Sorbents of Various Types. Materials 2023, 16, 4088. https://doi.org/10.3390/ma16114088

AMA Style

Bezhin NA, Shibetskaia IG, Kozlovskaia ON, Slizchenko EV, Tananaev IG. 7Be Recovery from Seawater by Sorbents of Various Types. Materials. 2023; 16(11):4088. https://doi.org/10.3390/ma16114088

Chicago/Turabian Style

Bezhin, Nikolay A., Iuliia G. Shibetskaia, Ol’ga N. Kozlovskaia, Evgeniy V. Slizchenko, and Ivan G. Tananaev. 2023. "7Be Recovery from Seawater by Sorbents of Various Types" Materials 16, no. 11: 4088. https://doi.org/10.3390/ma16114088

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop