Waste-to-Energy

Waste cooking oil (WCO) biodiesel has some disadvantages, such as poor cold flow properties, low oxidation stability, and flash point during storage. These poor physicochemical properties can be improved by different ways, such as the addition of non-edible oil. The aim of this study to analyse physicochemical properties of the biodiesel made by between WCO and Schleichera oleosa (SO). The biodiesel produced with 70:30% of WCO and SO respectively as crude oil, further introducing of different KOH-based catalyst into this oil to obtained the methyl ester. The optimum yield transesterification process are 94% with 60 min. of the reaction time, 1 wt.% KOH, and 12:1 molar ratio the methanol to oil. On the other hand, the Schleichera oleosa blend shows oxidation stability at 6.8 h and 3.3 h for Waste cooking oil methyl ester (WCME). The reduction of cold flow and, on the contrary, the flash point increase were obtained with a 70:30% ratio of WCO and SO. The cold flow properties and flash point of the fuel. Thus, mixed WCO and Schleichera oleosa oil improve the physiochemical properties such as oxidation stability, flash point, and cold flow of biodiesel without the need for synthetic antioxidants. Full article

Developments in waste incineration technology in terms of efficient fuel preparation, combustion, and emissions reduction, as well as the growing needs of the community in terms of electricity, water, and air conditioning loads, are the prime motive for this study. This study presents a novel approach, in which three models of the fluidized bed combustion of municipal waste for simultaneous power generation, freshwater production, and district cooling are analyzed for their energy and exergy performance. The three simultaneously evaluated utility models are different configurations of a fluidized bed combustion system with Rankine cycle power generation, cooling with a vapor absorption refrigeration system, and fresh water production using multiple effect desalination. The output from the turbine, cooling system, and desalination system is determined using the Engineering Equations Solver for different boiler operating pressures. Energy and exergy analysis data for different pressures are used to identify the best configuration. Two variants of the absorption cooling system, namely, single effect and double effect, are considered. The variants of the multiple-effect desalination are the three-stage and five-stage methods. Input parameters used in this study are municipal solid waste generation and composition data collected for an urban community in an arid climate zone with high demand for electric power, cooling, and fresh water. Model 2, which contains two turbines with the reheating and cooling systems connected to a high-pressure turbine and water desalination connected to a low-pressure turbine, gave the best overall performance. Significant savings in terms of the replacement of conventional energy were observed from these waste conversion plants with greater benefits in arid weather conditions. The results obtained by different models under different operating criteria constitute a guideline for municipal planners for the selection of appropriate waste utilization technology, as well as the appropriate operations. Full article

The mass arrival of pelagic sargassum is an international issue that is currently taking its toll on the economic activity of affected regions by causing a significant reduction in investment and tourism. The purpose of this work was to evaluate the Logistic Modified and Gompertz Modified sigmoid kinetic models for describing the lag phase in the generation of biomethane. The case studies were: anaerobic co-digestion (ACoD) of Sargassum spp./domestic organic waste and Sargassum spp. in mono-digestion. The experimental method, based on biochemical methane potential (BMP), enabled kinetic models to be built for methane production under environmental conditions and an estimate to be made for the duration of the lag phase. The maximum cumulative production determined for monodigestion was 140.7 cm³ of CH₄/g SV at 99 days, and for ACoD, it was 161.3 cm³ of CH₄/g SV at 172 days. The lag phase was determined to be approximately 7 days and 93 days, respectively. It was concluded that the modified sigmoid growth functions are a valuable tool for studying the start-up and scaling of systems for the ACoD of organic waste. The results present the ACoD of coastal pelagic sargassum algae and domestic organic waste as a potential alternative energy source. Full article

Biogas consists of mainly methane, as a source of energy, and impurities such as carbon dioxide, hydrogen sulphide, water, and siloxanes. These impurities, such as hydrogen sulphide, reduce the biogas energy content and corrode equipment that store, transport, or utilise biogas. Several reviews on upgrading biogas to biomethane have been published, but minimal focus has been put on upgrading biogas for commercialisation in South Africa. Thus, this study reviewed biogas upgrading techniques in South Africa to put together information on activities and experiences on biogas valorisation to enhance the chances for different stakeholders to learn and build on from local experiences. To capture all relevant information, literature from the past 10 years was retrieved from online databases and government, municipality, and companies’ websites and institutional repositories. The review covered the sorption, separation, and in situ techniques that are globally used for upgrading biogas. The status of the biogas sector and the upgrading activities that occur in the country with their cost, energy, and environmental impacts were given in detail. It is estimated that a total of 3 million Nm³d⁻¹ of biogas can be produced in the country from biogas substrates. Thus, researchers and entrepreneurs are encouraged to collaborate to utilise the abundant resources used for biogas production to enhance the commercialisation of biomethane. Full article

A large part of municipal solid waste (MSW) still goes to landfills, representing an environmental concern. A circular economy approach can enable safe management of MSW while mitigating the increasing energy needs when waste is used as a feedstock in energy production processes (waste to energy). Currently, MSW can be converted into refuse-derived fuel (RDF) through mechanical and biological treatment processes. This study analyzes the status of MSW and RDF production, as well as its main destinations in Portugal and Europe. The legislation applied, possible energy-recovery routes, and challenges associated with energy recovery are discussed throughout this paper. This research finds that the production of RDF in Portugal has been neglected, mostly because of RDF composition being quite heterogeneous and its poor fuel properties. Therefore, the need to improve and upgrade the characteristics and properties of RDF for waste-to-energy processes was detected. RDF can be pretreated to be further applied to waste-to-energy and waste-to-gas processes, such as incineration and gasification. The technology readiness level data, costs, and SWOT analysis allowedto assess that although incineration is the most mature and widely used technology, gasification becomes more attractive, having lower costs and gaseous emissions, proving to be more efficient and sustainable for MSW and RDF conversion. Full article

The microbial production of fuel ethanol is an attractive and sustainable biotechnological approach. This study presents a metabolic engineering strategy of Zymomonas mobilis aimed at coproducing bioethanol and fatty acids. The increased flux of fatty acids stabilizes the cell membrane and thus counteracts the progressively higher ethanol toxicity. In a glucose medium, the highest ethanol titer achieved was 146.7 g/kg of broth, surpassing the wild-type Z. mobilis CP4 and angel yeast by 30% and 45%, respectively. The recombinant strain exhibited a total fatty acid titer of 0.4 g/L from 230 g/L total sugar solution (5 L bioreactor), representing a 12-fold increase compared to the wild-type Z. mobilis CP4. Furthermore, when using a 4:2:1 mixture of glucose: xylose: mannose (w/v), an ethanol concentration of 142.8 g/kg of broth was attained, only 2.66% lower than that of the glucose-only medium. These findings highlight the enormous potential of this genetically engineered strain for the sustainable production of ethanol and fatty acids from lignocellulosic renewable carbon sources. Full article

The article describes the process of hot water extraction treatment of a specific material—in this case, shavings of hemp shives of different thicknesses, sorted by their thickness into three different fractions of 0–4 mm, 4–8 mm, and 8–12 mm. In addition, each sample from a given fraction was separately subjected to one, two, and three extraction processes. After the material was treated with extraction, cellulose determination was performed using the Kürschner–Hoffer method in order to find out the effect that hot water extraction had on the cellulose content of the test material. This research aims to determine whether hot water extraction strongly alters the cellulose content, which may translate into a change in efficiency when producing second-generation biofuel produced from this material. The cellulose determination showed the smallest cellulose losses were in chips 4–8 mm thick, while the largest were in chips 0–4 mm thick. Each repetition resulted in a loss of cellulose, with the steepest loss occurring after the second repetition of HWE, and the smallest after the third repetition—the exception being the 4–8 fraction, in which the smallest decrease occurred after the first repetition of the HWE (Hot Water Extraction) process. Full article

Due to the economic inefficiency of material recycling of general industrial waste and urban waste, the use of solid recovered fuels (SRFs) not only mitigates the environmental loadings from waste incineration plants and sanitary landfills but also creates green electricity and/or heat and thus reduces the use of fossil fuels. In this regard, the Taiwan government formulated the “Solid Recovered Fuel Manufacturing Guidelines and Quality Standards” in 2020 to ensure the manufacturing quality of SRFs. This paper focused on the status of waste management and energy supply, the current regulations for adopting SRFs, and the challenges in the development of SRFs from the viewpoints (or life cycle) of the environmental, economic, and engineering (or technological) characters in Taiwan. Based on the database of the official handbook/yearbook, the energy supply from indigenous biomass and waste was 1678.7 × 10³ kiloliters of oil equivalent (KLOE) in 2021, which only accounted for about 1.2% of the total energy supply. Obviously, available indigenous biomass and waste for producing SRFs were mostly from waste wood, sugarcane bagasse, and mixtures containing wood/paper. Finally, some suggestions for the increasing use of SRFs in the energy and industrial sectors were addressed to keep in step with the sustainable development goals (SDGs) in 2030, especially in the mitigation of GHG emissions. Full article

Inadequate disposal of Municipal Solid Waste (MSW) is one of the greatest environmental issues confronted nowadays. One of the techniques used for its final disposal is incineration, otherwise known as mass burning. Although this procedure remains very controversial in Brazil, some recent studies published in Europe reveal a large amount of misinformation about it. It has been widely used in European countries, Japan, and a few U.S. cities and has been increasingly and significantly adopted in China. Therefore, this article aims to carry out a literature review on the evolution of waste-to-energy recovery from Municipal Solid Waste (MSW) worldwide and the progress of mass-burning technologies, particularly in the Brazilian context. For such a purpose, global scientific databases were selected and some of their results allowed us to present how the main WtE recovery technologies function, as well as their benefits and impacts. Moreover, it was possible to systematize the main regulatory frameworks on the theme in Brazil and to reveal the country’s electricity generation capacity, in addition to depicting the progress of Waste-to-Energy Plants (WtEPs) undergoing licensing processes in the state of São Paulo. Full article

A high load of inorganics in raw lignocellulosic biomass is known to inhibit the yield of bio-oil and alter the chemical reactions during fast pyrolysis of biomass. In this study, palm kernel shell (PKS), an agricultural residue from palm oil production, and two other woody biomass samples (mahogany (MAH) sawdust and iroko (IRO) sawdust) were pretreated with distilled water or an acidic solution (either acetic, formic, hydrochloric (HCl) or sulfuric acid (H₂SO₄)) before fast pyrolysis in order to investigate its effect on the primary products and pyrolysis reaction pathways. The raw and pretreated PKS, MAH and IRO were pyrolysed at 600 °C and 5 s with a micro-pyrolyser connected to a gas chromatograph–mass spectrometer/flame ionisation detector (GC-MS/FID). Of the leaching solutions, HCl was the most effective in removing inorganics from the biomass and enhancing the primary pyrolysis product formed compared to the organic acids (acetic and formic acid). The production of levoglucosan was greatly improved for all pretreated biomasses when compared to the original biomass but especially after HCl pretreatment. Additionally, the relative content of the saccharides was maximised after pretreatment with H₂SO_4, which was due to the increased production of levoglucosenone. The relative content of the saccharides increased by over 70%. This increase may have occurred due to a possible reaction catalysed by the remaining acid in the biomass. The production of furans, especially furfural, was increased for all pretreatments but most noticeable when H₂SO₄ was used. However, the relative content of acids and ketones was generally reduced for PKS, MAH and IRO across all leaching solutions. The relative content of the phenol-type compound decreased to a large extent during pyrolysis after acid pretreatment, which may be attributed to dehydration and demethoxylation reactions. This study shows that the production of valuable chemicals could be promoted by pretreatment with different acid solutions. Full article

Bio-SRF based on livestock waste has low heating value and high moisture content. The concentration of toxic gases such as SOx, NOx, and HCl in the flue gas is changed according to the composition of fuel, and it has been reported. Therefore, the study of fuel combustion characteristics is necessary. In this study, we investigated combustion characteristics on the blended firing of coal and Bio-SRF (bio-solid refused fuel) made from livestock waste fuel in CFBC (circulating fluidized bed combustor). The raw materials for manufacturing Bio-SRF include agricultural waste, herbaceous plants, waste wood, and vegetable residues. Bio-SRF, which is formed from organic sludge, has a low heating value and a high moisture content. Bio-SRF of livestock waste fuel is blended with different ratios of coal based on heating values when coal is completely combusted in CFBC. In the result of experiment, the combustor efficiency of calculated unburned carbon concentration in the fly ash shows 98.87%, 99.04%, 99.64%, and 99.71% when the multi co-combustion ratio of livestock waste fuel increased from 100/0 (coal/livestock waste) to 70/30 (coal/livestock waste). In addition, the boiler efficiency is shown to be 86.23%, 86.30%, 87.24% and 87.27%. Through the experimental results, we have identified that co-combustion of livestock waste fuel does not affect boiler efficiency. We have systematically investigated and discussed the temperature changes of the internal combustor, compositions of flue gases, solid ash characteristics, and the efficiency of combustion and of the boiler during co-combustion of coal and Bio-SRF. Full article

The use of energy from waste can be a key means of reducing the consumption of fossil fuels and thus reduction of greenhouse gas emissions. Waste energy can be a worthy alternative to conventional energy sources in construction. This paper presents data on energy consumption for the preparation of domestic hot water in residential buildings. A review of the literature sources and inventions in the area of waste energy recovery from grey water was carried out. It also presents the results of research on prototypes of devices used to receive energy deposited in wastewater, published in recent years. The benefits of using drain water heat recovery systems for preheating utility water in residential buildings are presented. An analysis of technical solutions for grey water energy collection units was made, revealing their advantages and disadvantages. Great importance was attached to the review of patent sources as well as devices available on the market. According to the authors, the results of the technical review may be useful for contractors and designers of heat recovery equipment and installations, researchers and potential users of these technologies. Full article

Global economic development and the associated increase in consumption increase the demand for plastics. The result of these changes is the increase in the share of this group of used plastics in the structure of household waste. An innovative way of managing plastic waste is to use it as a component of a high-energy material. According to the conceptual assumptions, some plastics introduced into the structure of an explosive (Ex) in appropriate amounts can improve the energy parameters of a high-energy material. Modification of the composition of the explosive causes a change in its explosive and operational parameters. It also becomes necessary to develop a method of introducing an additional component. Computer programs for thermodynamic calculations are a tool for modeling the predicted energy parameters of an explosive. The performed simulations and modeling allow for the selection of appropriate compositions for laboratory and “in situ” tests. This reduces the number of field tests performed. This enables the more effective design of new explosive compositions. The use of waste plastics as a corrector of explosive properties may also be pro-environmental in nature through the use of a detonation method of their disposal and will reduce the cost of manufacturing the product. The conducted analyses showed that for three ANFO-type explosives containing 2% polyethylene—PE 2.0, 1% polypropylene—PP 1.0 and 1% polyurethane—PU 1.0, obtained energy parameters similar to ANFO and qualitatively and quantitatively similar structure of post-detonation gases. Full article

To mitigate the various problems caused by using conventional plastics, bioplastic (BP) has emerged as a substitute for plastics. BP wastes after use are commonly treated using composting, causing many environmental problems. Anaerobic digestion (AD) has become prominent as an alternative method of producing renewable energy. The aim of this study was to estimate the methane production yield (MPY) of BPs (polylactic acid (PLA) and polyhydroxyalkanoate (PHA)) with mechanical pretreatment (particle size < 0.5 cm) and investigate the effect of co-digestion of BPs and food waste (FW). Batch experiments were conducted under mesophilic and thermophilic conditions at various mixing ratios (FW/PLA or PHA = 95:5 and 90:10 on a weight basis). During 20 d of digestion at temperatures of 37 and 55 °C, MPYs of PHA were 153.8–172.0 mL CH₄/g chemical oxygen demand (COD), but that of PLA was significantly low (<25.6 mL CH₄/g COD). Higher MPYs were attained at 55 °C than at 37 °C. The synergistic effects of FW addition on BP AD were observed at both temperatures, especially at 55 °C. By comparing theoretical (based on mono-digestion results) and actual (based on co-digestion results) MPYs, the synergistic effect of FW addition on MPY of co-digestion reached 8.5–26.6% and 12.7–25.5% for PLA- and PHA-fed tests, respectively. The biodegradation rates (on a volatile solids (VS) basis) of PLA and PHA were 6.0–13.7% and 49.1–52.3% and increased by 1.8–4.3 and 1.2–1.5 times in the PLA- and PHA-fed co-digestion tests, respectively. Co-digestion of FW might be a feasible treatment option for BPs combined with simple mechanical pretreatment. Full article

The VALUEWASTE project can offer a sustainable solution to transform biowaste into added-value bioproducts, such as proteins from microorganisms and insects and biofertilizers. The present study focused on the environmental impacts linked to obtaining these bioproducts, which was performed by the standardized Life Cycle Assessment (LCA) approach, using the Environmental Footprint methodology to evaluate the midpoint impact categories considered. At the same time, the bioproducts coming from biowaste were compared to regular ones: other protein sources and mineral fertilizers. The study results show that these new protein sources are firm candidates to reach the market from an environmental point of view. Furthermore, their environmental impacts could be improved by reducing the energy use (the main contributor) within some impact categories, such as ecotoxicity and global warming. In case of the biofertilizers, their environmental performance was overall worse compared to mineral fertilizers, except for the following impact categories: mineral and metal use and water scarcity. Nevertheless, these biofertilizers come from biowaste, extending the circularity concept, and from local places, reducing the dependency on other actors. Hence, the study showed that the obtained bioproducts are real alternatives to implement in a circular economy. However, continuous improvement of the solution should be performed. Full article

A growing awareness of global climate change has led to an increased interest in investigating renewable energy sources, such as the anaerobic digestion of biomass. This process utilizes a wide range of microbial communities to degrade biodegradable material in feedstock through a complex series of biochemical interactions. Anaerobic digestion exhibits nonlinear dynamics due to the complex and interacting biochemical processes involved. Due to its dynamic and nonlinear behavior, uncertain feedstock quality, and sensitivity to the process’s environmental conditions, anaerobic digestion is highly susceptible to instabilities. Therefore, in order to model and operate a biogas production unit effectively, it is necessary to understand which parameters are most influential on the model outputs. This also reduces the amount of estimation required. Through a scoping review, the present study analyzes the studies on the application of sensitivity analysis in anaerobic digestion modeling. Both local and global sensitivity analysis approaches were carried out using different mathematical models. The results indicate that anaerobic digestion model no.1 (ADM1) was the most commonly used model for analyzing sensitivity. Both local and global sensitivity analyses are widely employed to investigate the influence of key model parameters such as kinetic, stoichiometric, and mass transfer parameters on model outputs such as biogas production, methane concentration, pH, or economic viability of the plant. Full article

Waste management and electricity supply have always been among the main challenges faced by developing countries. So far, the use of waste to energy (WtE) is one strategy that could simultaneously address these two challenges. However, the use of such technologies requires detailed studies to ensure their sustainability. In this paper, the potential of WtE in two cities in Nigeria (Abuja and Lagos) using anaerobic digestion (AD), incineration, gasification and landfill gas to energy (LFGTE), is presented with the aim of evaluating their economic viability using life cycle costing (LCC) as an analytical tool. This economic feasibility analysis includes LCC, levelised cost of electricity (LCOE), net present value (NPV), internal rate of return (IRR) and payback period. A sensitivity analysis was conducted to investigate the influence of several parameters on the economic viability of the selected technologies for the two cities. The economic assessment revealed that all the WtE systems were feasible and viable in both cities except for LFGTE in Abuja where the NPV was negative (−USD 105.42/t), and the IRR was 4.17%. Overall, incineration for both cities proved to be the most favourable economic option based on its positive LCC (Lagos USD 214.1/t Abuja USD 232.76/t), lowest LCOE (Lagos USD 0.046/t Abuja USD 0.062/t), lowest payback period (Lagos 1.6 years Abuja 2.2 years) and the highest IRR (Lagos 62.8% Abuja 45.3%). The results of the sensitivity analysis also indicated that variation in parameters such as the capital cost and discount rate have significant effects on the LCC. This paper provides information for potential investors and policy makers to enhance optimal investment in WtE technologies in Nigeria. Full article

The Iwan model is composed of elastoplastic elements and is widely used to represent the stiffness degradation of bolted joints under mixed-mode loading (normal and tangential loading). The latest static methods of parameter identification established the relationship between the elastoplastic elements and the contact pressure under normal loading. Under mixed-mode loading, the parameters of the Iwan model are dynamic for the evolution of contact conditions. Therefore, static parameter identification methods are not suitable for the dynamic Iwan model. A new technique was proposed to identify the parameters of the elastoplastic elements in this paper. Firstly, several different finite element models were established. The influence of the contact method and the thread structure were analyzed, and a reliable and efficient bolted-joint modeling method was proposed. Secondly, the evolution of contact conditions was studied. The dynamic elliptical contact model and the ellipticity discrete method were proposed. Finally, the residual stiffness of the Iwan model was analyzed to establish the mapping between the residual stiffness and the bending of the screw. The results can provide a technique for identifying the parameters of the dynamic Iwan model. Full article

Plastic waste accumulation has been growing due to the increase in plastic generation and the lack of infrastructure for recycling. One of the approaches is to treat the mixed plastic waste (MPW) through thermal processes to produce feedstocks for other applications. However, the presence of polyvinyl chloride (PVC) in MPW would produce HCl during processing and has negative impacts (emission, catalyst poisoning, etc.). In addition, due to the high heterogeneity of MPW, it is difficult to generate consistent experimental data. In this study, MPW was homogenized through double compounding–extrusion and then formed into a sheet to be treated at 400 °C. The solid products at various mass losses were characterized by heat and chlorine content, Fourier-transform infrared (FTIR) spectroscopy, and elemental composition analysis. It was found that the thermal degradation of MPW started at ~260 °C. The chlorine removal efficiency increased with mass loss and reached an asymptotic value of ~84% at ~28% mass loss, and the remaining chlorine can be attributed to inorganic sources. A PVC de-chlorination model was developed for MPW using TGA data for PVC and MPW to determine organic chlorine removal efficiency. These results show that PVC de-chlorination was not affected by other plastics at this temperature. As the mass loss increases, the heat content first increases and then decreases. It was found that mass loss is a universal parameter for organic chlorine removal efficiency and heat content. The elemental composition analysis and FTIR spectroscopy also shed more light into the chemical changes during MPW thermal degradation. Full article

Converter gas (BOFG) is a by-product of the steel manufacturing process in steelworks. Its usage as a substitute fuel instead of natural gas for fueling a metallurgical furnace seems to be reasonable due to potential benefits as follows: CO₂ emission reduction into the ambient air and savings in purchasing costs of natural gas. Results of theoretical analysis focused on implementing converter gas as a fuel for feeding a tunnel furnace for either steel plate rolling, steel sheet hardening in its real working condition or both, are discussed. The analysis was focused on the combustion chemistry of the converter gas and its potential ecological and economic benefits obtained from converter gas usage to heat up steel in a tunnel furnace. Simulations of combustion were conducted using a skeletal chemical kinetic mechanism by Konnov. The directed relation graph with error propagation aided sensitivity analysis (DRGEPSA) method was used to obtain this skeletal kinetic mechanism. Finally, the model was validated on a real tunnel furnace fueled by natural gas. Regarding exhaust emissions, it was found that nitric oxide (NO) dropped down from 275 to 80 ppm when natural gas was replaced by converter gas. However, carbon dioxide emissions increased more than three times in this case, but there is no possibility of eliminating carbon dioxide from steel manufacturing processes at all. Economic analysis showed savings of 44% in fuel purchase costs when natural gas was replaced by converter gas. Summing up, the potential benefits resulting from substituting natural gas with converter gas led to the conclusion that converter gas is strongly recommended as fuel for a tunnel furnace in the steel manufacturing process. Practical application requires testing gas burners in terms of their efficiency, which should provide the same amount of energy supplied to the furnace when fed with converter gas. Full article