Application of Graphene-Based Materials

This Topic on the “Application of Graphene-Based Materials”, which consists of a total of twenty-six articles, including two review articles, written by research groups of experts in the field, considers the most recent research and trends on the synthesis and characterization of graphene-based materials, including nanohybrids, intended for a vast array of high-demanding technological applications, namely batteries/fuel cells, aerogels, laser technology, sensors, electronic/magnetic devices, catalysts, etc [...] Full article

Graphene is a promising candidate used to reduce friction and wear in micro- and nano-device applications owing to its superior mechanical robustness and intrinsic lubrication properties. Herein, we report the frictional and wear resistance properties of a graphene-coated polymer and how they are affected by fabrication processes. The results show that graphene deposited on a polymer substrate effectively improves both frictional and wear resistance properties, and the degree of improvement significantly depends on the graphene transfer method and interfacial adhesion between graphene and the substrate. Dry-transferred graphene showed better improvement than wet-transferred graphene, and the strong adhesion of graphene achieved by imidazole treatment aided the improvement. A combined analysis of surface morphology and scratch trace shows that the graphene transfer method and graphene adhesion dominate the structural integrity of the transferred graphene, and the graphene/substrate interfacial adhesion plays a decisive role in the improvement of both properties by suppressing the delamination of graphene from the substrate during the nanoscratch test, thereby preventing crack formation in graphene and weakening the puckering effect. Full article

It is proposed that nanosized graphene aggregation could facilitate coherent neutron scattering under particle size conditions similar to nanodiamonds to enhance neutron intensity below cold neutrons. Using the RIKEN accelerator-driven compact neutron source and iMATERIA at J-PARC, we performed neutron measurement experiments, total neutron cross-section and small-angle neutron scattering on nanosized graphene aggregation. For the first time, the measured data revealed that nanosized graphene aggregation increased the total neutron cross-sections and small-angle scattering in the cold neutron energy region. This is most likely due to coherent scattering, resulting in higher neutron intensities, similar to nanodiamonds. Full article

This study investigates the thermal effect of supercritical water treatment at different temperatures (150, 175, 200 °C) and semi-vacuum state (−0.08 MPa) on graphite flakes which are then incorporated into nylon 610. The treatment is deemed to increase the surface activity of nanofillers through the formation of oxygen-containing functional groups. X-ray diffraction (XRD) analysis indicated that the crystal structure of the flakes remained similar before and after supercritical water treatment. Fourier transform infrared spectroscopy (FTIR) also showed the presence of hydrogen bonding between the flakes and the polymer matrix through the appearance of amide bands. The intensity of the amide peaks is higher for nanocomposites with treated flakes than untreated ones. Furthermore, scanning electron microscopy (SEM) showed that at higher wt%, aggregation will occur, which leads to a weakening in physical properties. The tensile strength of nanocomposites with treated flakes decreased with increasing wt%, while those with untreated flakes increased with increasing wt%. Young’s modulus of all the nanocomposites generally increased with increasing wt%. The highest tensile strength obtained is 967.02 kPa, while that of neat nylon 610 is 492.09 kPa. This enhancement in mechanical properties can be attributed to the intact structure of the graphite flakes and the interaction between the flakes and the nylon 610 matrix. A higher temperature of water treatment was discovered to cause higher oxidation levels on surface of the nanofillers but would result in some structural damage. The optimum nylon 610 nanocomposite synthesized was the one that was incorporated with 1.5 wt% graphite flakes treated at 150 °C and −0.08 MPa, as it has the highest tensile strength. Full article

The process of acoustically stimulated charge transport in the graphene film on the surface of the $YZ-$cut of a LiNbO₃ crystal was investigated. It was found that the dependence of the current in the graphene film on the frequency of the surface acoustic wave (SAW) excitation repeats the amplitude-frequency response of the SAW delay time line. It is shown that increasing the SAW amplitude leads to an increase in the current in the graphene film, and the current in the graphene film depends linearly on the amplitude of the high-frequency input signal supplied to the interdigital transducer (IDT, in dB). It is demonstrated that at a positive bias potential on the graphene film, the SAW propagation allows to change the direction of the current in the graphene film by changing the amplitude of the SAW. It is also shown that in the frequency range of the amplitude-frequency response of the SAW delay time line, the current in the graphene film can vary from positive to negative values depending on the frequency. The capability to control the SAW excitation frequency or the SAW amplitude makes it possible to control the value and direction of the current in the graphene film. The SAW propagation lets to collect and transport the photo-stimulated charges in the graphene film on the crystal surface. Full article

Vertically aligned graphite substrate (VGS)-copper packaging was renowned for improving the robustness against the thermal gradient loading by using micro texturing. The micro-groove array with a line width of 50 μm and a pitch of 100 μm was formed into the VGS by controlling the line depth with the use of fast-rate oxygen plasma etching. Three micro-grooved VGS specimens were wet-plated to fill these microgrooves with copper deposits and to cover the VGS surfaces. The nearly full-deposited VGS-Copper specimens were subjected to a severe thermal transient loading test. The simply Cu-covered package and shallow rib-structured VGS-Cu packages were damaged to delaminate at their interfaces. The VGS-Cu package with the copper rib structure with a height of 50 μm experienced no delamination. This rib-structured VGS-copper package with high rib height had sufficient robustness against the severe thermal transients even with the proof of homogeneous thermal spreading capacity. Full article

With the incredible discovery of graphene (Gr), all of the properties studied to date suggest that it has promising applications in the development of semiconductor, spintronic, insulating, and polymer materials. However, efforts are still underway to fully understand the nature of metal–graphone(GrH) interaction in order to offer better scope for tuning the electronic and magnetic properties, which can be performed by intercalation of atoms via metal support on graphene. We chose metal atoms belonging to the s and p blocks, namely Na and Al, respectively, as the intercalating atoms. Herein, the maximum coverage of a monolayer of Na and Al was comparatively studied on a Ni(111) surface. Significant changes in the magnetic and electronic properties at the Ni(111)/graphone interface were observed upon intercalation. Of the two intercalating metal atoms, Na proved to be more effective, such that the magnetic properties of the surface Ni were only slightly decreased, and the graphone also showed better magnetic properties than in the absence of Na. Full article

Water contamination around the world is an increasing problem due to the presence of contaminants such as arsenic, fluoride, and chromium. The presence of such contaminants is related to either natural or anthropogenic processes. The above-mentioned problem has motivated the search for strategies to explore and develop technologies to remove these contaminants in water. Adsorption is a common process employed for such proposals due to its versatility, high adsorption capacity, and lower cost. In particular, graphene oxide is a material that is of special interest due to its physical and chemical properties such as surface area, porosity, pore size as well as removal efficiency for several contaminants. This review shows the advances, development, and perspectives of materials based on GO employed for the adsorption of contaminants such as arsenite, arsenate, fluoride, and hexavalent chromium. We provided a detailed discussion of the synthesis techniques and their relationship with the adsorption capacities and other physical properties as well as pH ranges employed to remove the contaminants. It is concluded that the adsorption capacity is not proportional to the surface area in all the cases; instead, the synthesis method, as well as the functional groups, play an important role. In particular, the sol–gel synthesis method shows better adsorption capacities. Full article

In this work, a novel ternary nanocomposites AgZnS-TiO₂-reduced graphene oxide (RGO) was successfully synthesized by a facile soft ultrasonic-reduction condition as low as 70 °C. During the ultrasound reaction, the reduction of GO and the growth of AgZnS and TiO₂ crystals occurred simultaneously in conjunction with the deposition of AgZnS and TiO₂ crystals onto the surface of the graphene. The synthesized nanocatalysts were characterized by XRD, SEM, TEM, EDX, Raman spectroscopy, XPS, UV–Vis DRS, photoluminescence spectrometer, and photocurrent and CV. The AgZnS-G-T was shown as catalytic HER with some synnegetic factors such as pH-universal, temperature, and ultrasonic condition. After 4 h, it was observed that AgZnS-TiO₂-RGO has the highest efficiency of photocatalytic activity through hydrogen production by water splitting, which achieved the highest hydrogen evolution rate of 930.45 μmol/g at buffer solution (pH = 5), which was superior to AgZnS-G (790.1 µmole/g) and AgZnS (701.2 µmole/g). Such a significant hydrogen evolution amount far exceeded that of undoped TiO₂ and RGO. The H₂ evolution amounts increased significantly at ultrasonic irradiation power of 80 MHz. AgZnS-G-T demonstrates the higher H₂ evolution amounts of 985 µmole/g at 80 MHz. Its photocatalytic hydrogen-evolution activity remained at a high level over four cycles (16 h) nanoparticle. Full article

A very attractive advantage of graphene is that its Fermi level can be regulated by electrostatic bias doping. It is of great significance to investigate and control the spatial location of graphene emission for graphene thermal emitters, in addition to tuning the emission intensity and emission spectrum. Here, we present a detailed theoretical model to describe the graphene emission characteristics versus gate voltages. The experimentally observed movement of the emission spot and temperature distribution of graphene emitters are basically in agreement with those from the theoretical model. Our results provide a simple method to predict the behavior of graphene emitters that is beneficial for achieving the spatial dynamic regulation of graphene infrared emission arrays. Full article

Carbon films were fabricated on the orthodontic stainless steel archwires by using a custom-designed electron cyclotron resonance (ECR) plasma sputtering deposition system under electron irradiation with the variation of substrate bias voltages from +5 V to +50 V. Graphene sheets embedded carbon (GSEC) films were fabricated at a higher substrate bias voltage. The fretting friction and wear behaviors of the carbon film-coated archwires running against stainless steel brackets were evaluated by a home-built reciprocating sliding tribometer in artificial saliva environment. Stable and low friction coefficients of less than 0.10 were obtained with the increase of the GSEC film thickness and the introduction of the parallel micro-groove texture on the bracket slot surfaces. Particularly, the GSEC film did not wear out on the archwire after sliding against three-row micro-groove textured bracket for 10,000 times fretting tests; not only low friction coefficient (0.05) but also low wear rate (0.11 × 10⁻⁶ mm³/Nm) of the GSEC film were achieved. The synergistic effects of the GSEC films deposited on the archwires and the micro-groove textures fabricated on the brackets contribute to the exceptional friction and wear behaviors of the archwire-bracket sliding contacts, suggesting great potential for the clinical orthodontic treatment applications. Full article

Direct ethanol fuel cells (DEFCs) are considered the most suitable direct alcohol fuel cell (DAFC) in terms of safety and current density. The obstacle to DEFC commercialization is the low reaction kinetics of ethanol (C₂H₅OH) oxidation because of the poor performance of the electrocatalyst. In this study, for the first time, graphene nanoplates (GNPs) were coated with sulfated zirconium dioxide (ZrO₂) as adequate support for platinum (Pt) catalysts in DEFCs. A Pt/S-ZrO₂-GNP electrocatalyst was prepared by a new process, polyol synthesis, using microwave heating. Field emission scanning electron microscope (FESEM) imaging revealed well-dispersed platinum nanoparticles supported on the S-ZrO₂-GNP powder. Analysis of the Fourier transform infrared (FTIR) spectrometry confirmed that sulfate modified the surfaces of the sample. In X-ray diffraction (XRD), no effect of S-ZrO₂ on the crystallinity net in Pt was found. Pt/S-ZrO₂-GNP electrode outperformed those with unsulfated counterparts, primarily for the higher access with electron and proton, confirming sulfonating as a practical approach for increasing the performance, electrocatalytic activity, and carbon monoxide (CO) tolerance in an electrocatalyst. A considerable decrease in the voltage of the CO electrooxidation peak from 0.93 V for Pt/C to 0.76 V for the Pt/S-ZrO₂-GNP electrode demonstrates that the new material increases activity for CO electrooxidation. Moreover, the as-prepared Pt/S-ZrO₂-GNPs electrocatalyst exhibits high catalytic activity for the EOR in terms of electrochemical surface area with respect to Pt/ZrO₂-GNPs and Pt/C (199.1 vs. 95 and 67.2 cm².mg⁻¹ Pt), which may be attributed to structural changes caused by the high specific surface area of graphene nanoplates catalyst support and sulfonating effect as mentioned above. Moreover, EIS results showed that the Pt/S-ZrO₂-GNPs electrocatalyst has a lower charge transfer resistance than Pt/ ZrO₂-GNPs and Pt/C in the presence of ethanol demonstrating an increased ethanol oxidation activity and reaction kinetics by Pt/S-ZrO₂-GNPs. Full article

The development of new applications of graphene oxide in the biomedical field requires the covalent bonding of bioactive molecules to a sheet skeleton. Obtaining a large carboxyl group population over the surface is one of the main targets, as carboxyl group concentration in conventional graphene oxide is low among a majority of non-useful sp3-C-based functionalities. In the present work, we propose a selective method that yields an impressive increase in carboxyl group population using single-layer, thermally reduced graphene oxide as a precursor in a conventional Hummers–Offemann reaction. When starting with a reduced graphene oxide with no interlayer registry, sulfuric acid cannot form a graphite intercalated compound. Then, potassium permanganate attacks in in-plane (vacancies or holes) structural defects, which are numerous over a thermally reduced graphene oxide, as well as in edges, yielding majorly carboxyl groups without sheet cutting and unzipping, as no carbon dot formation was observed. A single-layer precursor with no ordered stacking prevents the formation of an intercalated compound, and it is this mechanism of the potassium permanganate that results in carboxyl group formation and the hydrophilic character of the compound. Full article

Egg white protein is a non-toxic and biodegradable biopolymer that forms a gel easily via simple thermal denaturation treatment. A novel aerogel on the basis of egg white protein crosslinked with graphene oxide was prepared via a facile freeze-drying method. The structure and physicochemical characteristics of the aerogels were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA) and Brunauer–Emmett–Teller (BET) analysis. The adsorption properties of the aerogels were investigated by studying the influencing factors such as the solution pH, dose, temperature and contact time. The adsorption capacity of methylene blue onto the aerogels was tested, whose maximum adsorption capacity, calculated by the Langmuir isotherm equation, reached 91.7 mg/g. Adsorption kinetics studies showed that the adsorption followed the pseudo-second-order kinetic model. Thermodynamic data implied that methylene blue adsorbed by the aerogels was an exothermic and spontaneous process. Full article

The esthetic clasp material is a clinical demand for a satisfactory removable partial denture. The purpose of this study is to assess the mechanical performance of graphene-based polymer (GBP) and polyether-ether-ketone (PEEK) materials as clasp materials. Thirty-two clasps were fabricated by CAD-CAM from two materials, GBP and PEEK. All clasps were tested for retention force after 10,000 cycles of insertion and removal and thermocycling. The clasp arms’ deformation was measured, and areas of stress–strain concentration were explored. The Mann–Whitney U test was used to compare the retentive force of the studied groups, while the independent sample t-test was applied to check the difference in clasp arm deformation at α = 0.5. The results showed a significantly higher retentive force (2.248 ± 0.315 N) in PEEK clasps, at p < 0.001. The deformation of the clasp arm of the GBP clasps was significantly higher than PEEK clasps. Areas of stress–strain concentration were seen at the junction of the retentive arm to the minor connector and at the retentive arm terminal. It could be concluded that PEEK polymer had a better mechanical performance as an esthetic clasp material than the GBP. An optimization study for GBP might be required to check the validity of such an application. Full article

Graphene has been regarded as a potential application material in the field of new energy conversion and storage because of its unique two-dimensional structure and excellent physical and chemical properties. However, traditional graphene preparation methods are complicated in-process and difficult to form patterned structures. In recent years, laser-induced graphene (LIG) technology has received a large amount of attention from scholars and has a wide range of applications in supercapacitors, batteries, sensors, air filters, water treatment, etc. In this paper, we summarized a variety of preparation methods for graphene. The effects of laser processing parameters, laser type, precursor materials, and process atmosphere on the properties of the prepared LIG were reviewed. Then, two strategies for large-scale production of LIG were briefly described. We also discussed the wide applications of LIG in the fields of signal sensing, environmental protection, and energy storage. Finally, we briefly outlined the future trends of this research direction. Full article

In this work, the electrical properties of graphene papers were investigated with the aim of developing pressure sensor prototypes for measuring pressures up to 2 kPa. In order to determine which graphene paper would be the most suitable, three different types of graphene papers, synthesized by different routes, were prepared and electrically characterized. The results of electrical characterizations, in terms of electrical conductivity and sheet resistance of graphene papers, are presented and discussed. Prototypes of pressure sensors are proposed, using graphene papers obtained by chemical oxidation (graphene oxide and reduced graphene oxide) and by electrochemical exfoliation. The prototypes were tested in static compression/decompression tests in the working range of 0 kPa to 1.998 kPa. The compression/decompression sensitivity values observed in these prototype sensors ranged from 20.8% ΔR/kPa for graphene sensors obtained by electrochemical exfoliation to 110.7% ΔR/kPa for those prepared from graphene oxide obtained by chemical oxidation. More expressive sensitivity values were observed for the sensors fabricated from GO, intermediate values for those made of rGO, while prototypes made of EG showed lower sensitivity. Full article

Poly(amic acid) (PAA) was synthesized from dianhydride 4,4-(4,4-isopropylidenediphenoxy)bis(phthalic anhydride) and diamine bis [4-(3-aminophenoxy) phenyl] sulfone. Colorless and transparent polyimide (CPI) hybrid films were synthesized through thermal imidization after dispersing nanofillers using an intercalation method in a PAA solution. C16-GS and C16-MMT, in which hexadecylamine (C16) was substituted on graphene sheet (GS) and montmorillonite (MMT), respectively, were used as nanofillers to reinforce the CPI hybrid films. These two nanofillers were admixed in varying loadings of 0.25 to 1.00 wt%, and the morphology, thermal properties, and optical transparency of the hybrid films were investigated and compared. The results suggest that the thermal properties of the CPI hybrid films can be improved by adding only a small amount of nanofiller. Transmission electron microscopy results of the CPI hybrid film containing two types of fillers suggested that the fillers were well dispersed in the nano-size in the matrix polymer; however, some of the fillers were observed as agglomerated particles above the critical concentration of 0.50 wt%. Full article

The strong bactericidal action of silver nanoparticles (AgNPs) is usually limited by their degree of aggregation. Deposition of AgNPs onto a graphene oxide (GO) surface to generate GO-Ag hybrids has been shown to be an effective method of controlling these aggregation problems. In this sense, a novel carboxylated graphene oxide–silver nanoparticle (GOCOOH-Ag) material has been synthesized, and their antibacterial and biofilm formation inhibitions have been studied. AgNPs decorating the GOCOOH surface achieved an average size of 6.74 ± 0.25 nm, which was smaller than that of AgNPs deposited onto the GO surface. In addition, better distribution of AgNPs was achieved using carboxylated material. It is important to highlight the main role of the carboxylic groups in the nucleation and growth of the AgNPs that decorate the GO-based material surface. In vitro antibacterial activity and antibiofilm-forming action were tested against Gram-positive (Staphylococcus aureus and Staphylococcus epidermidis) and Gram-negative bacteria (Pseudomonas aeruginosa and Escherichia coli). Both GO-Ag and GOCOOH-Ag reduced bacterial growth, analyzed by time–kill curves. However, the minimum inhibitory concentration and the minimum bactericidal concentration of GOCOOH-Ag were lower than those of GO-Ag for all strains studied, indicating that GOCOOH-Ag has better antibacterial activity. In addition, both nanomaterials prevent biofilm formation, with a higher reduction of biofilm mass and cell viability in the presence of GOCOOH-Ag. The carboxylation functionalization in GO-based materials can be applied to improve the bactericidal and antibiofilm-forming action of the AgNPs. Full article

Development of high-performance graphene-based microwave absorbing materials with low density and strong absorption is of great significance to solve the growing electromagnetic pollution. Herein, a controllable open-cell structure is introduced into graphene aerogels by the graphene oxide (GO) Pickering emulsion. The open-cell graphene aerogel (OCGA) with multiple microstructures shows a significantly enhanced microwave absorption ability without any additions. A high microwave absorption performance with the minimum value of reflection loss (RL_min) of −51.22 dB was achieved, while the material density was only 4.81 mg/cm³. Moreover, by means of centrifugation, the graphene cells were arranged by their diameter, and a gradient, open-cell graphene structure was first fabricated. Based on this unique structure, an amazing microwave absorption value of −62.58 dB was reached on a condition of ultra-low graphene content of 0.53 wt%. In our opinion, such excellent microwave absorption performance results from multiple reflection and well-matched impedance brought by the open-cell and gradient structure, respectively. In addition, the structural strength of the OCGA is greatly improved with a maximum increase of 167% due to the introduction of cell structure. Therefore, the OCGAs with the gradient structure can be an excellent candidate for lightweight, efficient microwave absorption materials. Full article

Graphite/graphene intercalation compounds with good and improving electrical transport properties, optical properties, magnetic properties and even superconductivity are widely used in battery, capacitors and so on. Computational simulation helps with predicting important properties and exploring unknown functions, while it is restricted by limited computing resources and insufficient precision. Here, we present a cost-effective study on graphite/graphene intercalation compounds properties with sufficient precision. The calculation of electronic collective excitations in AA-stacking graphite based on the tight-binding model within the random phase approximation framework agrees quite well with previous experimental and calculation work, such as effects of doping level, interlayer distance, and interlayer hopping on 2D $\pi$ plasmon and 3D intraband plasmon modes. This cost-effective simulation method can be extended to other intercalation compounds with unlimited intercalation species. Full article

An extensive experimental study was conducted to investigate the co-effects of surface area and distance between electrodes as well as filler scales on the percolation threshold of piezoresistive cement-stabilised sand. In this route, the electrical resistivity of numerous specimens of different sizes and composed of different content of carbon-based conductive fillers was measured, including carbon nanotubes (CNTs), graphene nanoplatelets (GNPs), and carbon fibres (CFs) with different aspect ratios. In addition, the numerical relations between the electrical percolation threshold and matrix dimensions were expressed for different conductive fillers. Furthermore, the electrical percolation threshold of two large-scale specimens with different shapes (a 10 × 10 × 85 cm³ beam, and a 15 cm size cube) were predicted through numerical relations, and their piezoresistivity performances were investigated under compression cyclic loading (cube) and flexural cyclic loading (beam). The mechanical properties of the specimens were also evaluated. The results showed that the changes in the length, width, and thickness of the matrix surrounded between electrodes had a significant effect on the electrical percolation threshold. However, the effects of length changes on the percolation threshold were greater than the width and thickness changes. Generally, increasing the aspect ratio of the conductive fillers caused a reduction in the electrical percolation threshold of the cementitious geocomposite. The appropriate piezoresistivity response of the large-scale specimens composed of filler content equal to their percolation threshold (obtained by the numerical relation presented in this study) showed the adequacy of the results in terms of threshold dosage prediction and self-sensing geocomposite design. The results of this study addressed a crucial factor for the design of self-sensing composites and pave the way for the development of field-applicable, smart, cementitious geocomposite. Full article

Advanced battery materials are urgently desirable to meet the rapidly growing demand for portable electronics and power. The development of a high-energy-density anode is essential for the practical application of B³⁺ batteries as an alternative to Li-ion batteries. Herein, we have investigated the performance of B³⁺ on monolayer (MG), bilayer (BG), trilayer (TG), and tetralayer (TTG) graphene sheets using first-principles calculations. The findings reveal significant stabilization of the HOMO and the LUMO frontier orbitals of the graphene sheets upon adsorption of B³⁺ by shifting the energies from −5.085 and −2.242 eV in MG to −20.08 and −19.84 eV in 2B³⁺@TTG. Similarly, increasing the layers to tetralayer graphitic carbon B³⁺@TTG_asym and B³⁺@TTG_sym produced the most favorable and deeper van der Waals interactions. The cell voltages obtained were considerably enhanced, and B³⁺/B@TTG showed the highest cell voltage of 16.5 V. Our results suggest a novel avenue to engineer graphene anode performance by increasing the number of graphene layers. Full article

A long-range surface plasmon polariton (SPP) waveguide, composed of double-layer graphene, can be pivotal in transferring and handling mid-infrared electromagnetic waves. However, one of the key challenges for this type of waveguide is how to excite the SPP modes through an incident light beam. In this study, our proposed design of a novel grating, consisting of a graphene-based cylindrical long-range SPP waveguide array, successfully addresses this issue using finite-difference time-domain simulations. The results show that two types of symmetric coupling modes (SCMs) are excited through a normal incident light. The transmission characteristics of the two SCMs can be manipulated by changing the interaction of the double-layer gratings of graphene as well as by varying various parameters of the device. Similarly, four SCMs can be excited and controlled by an oblique incident light because this light source is equivalent to two orthogonal beams of light. Furthermore, this grating can be utilized in the fabrication of mid-infrared optical devices, such as filters and refractive index sensors. This grating, with double-layer graphene arrays, has the potential to excite and manipulate the mid-infrared electromagnetic waves in future photonic integrated circuits. Full article

Efficient and environment-friendly nanopesticide delivery systems are critical for the sustainable development of agriculture. In this study, a graphene oxide nanocomposite was developed for pesticide delivery and plant protection with pyraclostrobin as the model pesticide. First, graphene oxide–pyraclostrobin nanocomposite was prepared through fast adsorption of pyraclostrobin onto graphene oxide with a maximum loading of 87.04%. The as-prepared graphene oxide–pyraclostrobin nanocomposite exhibited high stability during two years of storage, suggesting its high potential in practical application. The graphene oxide–pyraclostrobin nanocomposite could achieve temperature (25 °C, 30 °C and 35 °C) and pH (5, 7 and 9) slow-release behavior, which overcomes the burst release of conventional pyraclostrobin formulation. Furthermore, graphene oxide–pyraclostrobin nanocomposite exhibited considerable antifungal activities against Fusarium graminearum and Sclerotinia sclerotiorum both in vitro and in vivo. The cotoxicity factor assay revealed that there was a synergistic interaction when graphene oxide and pyraclostrobin were combined at the ratio of 1:1 against the mycelial growth of Fusarium graminearum and Sclerotinia sclerotiorum with co-toxicity coefficient values exceeding 100 in vitro. The control efficacy of graphene oxide–pyraclostrobin nanocomposite was 71.35% and 62.32% against Fusarium graminearum and Sclerotinia sclerotiorum in greenhouse, respectively, which was higher than that of single graphene oxide and pyraclostrobin. In general, the present study provides a candidate nanoformulation for pathogenic fungal control in plants, and may also expand the application of graphene oxide materials in controlling plant fungal pathogens and sustainable agriculture. Full article

The remote epitaxy of GaN epilayers on GaN/sapphire templates was studied by using different graphene interlayer types. Monolayer, bilayer, double-stack of monolayer, and triple-stack of monolayer graphenes were transferred onto GaN/sapphire templates using a wet transfer technique. The quality of the graphene interlayers was examined by Raman spectroscopy. The impact of the interlayer type on GaN nucleation was analyzed by scanning electron microscopy. The graphene interface and structural quality of GaN epilayers were studied by transmission electron microscopy and X-ray diffraction, respectively. The influence of the graphene interlayer type is discussed in terms of the differences between remote epitaxy and van der Waals epitaxy. The successful exfoliation of GaN membrane is demonstrated. Full article

The selective deposition of metals on dielectric materials is widely used in the electronic industry, making electro-conductive connections between circuit elements. We report a new low-cost laser-assisted method for the selective deposition of copper tracks on polymer surfaces by electroplating. The technique uses a laser for the selective modification of the polymer surface. The electrical conductivity of some polymers could be increased due to laser irradiation. Polyimide samples were treated using nanosecond and picosecond lasers working at a 1064 nm wavelength. An electro-conductive graphene-like layer was formed on the polymer surface after the laser treatment with selected parameters, and the copper layer thickness of 5–20 µm was deposited on the modified surface by electroplating. The selective laser-assisted electroplating technology allows the fabrication of copper tracks on complex shape dielectric materials. The technology could be used in the manufacturing of molded interconnect devices (MID). Full article