Special Issue "Recent Trends in Polymer Membranes: Fabrication Technique, Characterization, Functionalization, and Applications in Environmental Science"

A special issue of Polymers (ISSN 2073-4360). This special issue belongs to the section "Polymer Membranes and Films".

Deadline for manuscript submissions: 30 October 2023 | Viewed by 10678

Special Issue Editors

College of Chemistry and Chemical Engineering, Qingdao University, Qingdao 266071, China
Interests: CFD; separation science; functional nanomaterials; water purification
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

More than 90% of water in the world is comprised of salty water, and only about 2.5% can be used for human consumption. Among this proportion, most water resources are polluted by various industrial dyes, toxic metallic ions, drugs, pesticides, bacteria, and other aromatic organic chemicals. Polymer membranes with 3D networks and nanoporous structures provide a potential way to treat these pollutants in wastewater to obtain cleaning drinking water. Traditional polymer membranes have been widely used for water purification, but they are mostly limited by low selectivity, solution fluxes and fouling issues. In addition, some impurities and biological materials would aggregate on the surface or in the pores of the fabricated membranes, causing very poor selectivity, low water purification ability, reduced resilience, and increased energy consumption. The functionalization of polymer membranes with suitable chemicals, nanoparticles, and 2D graphene-like materials exhibits the possibility to create functional antifouling and antibacterial membrane materials. To promote the application of polymer membranes in environmental science, other relevant issues in membrane fabrication, characterization, physicochemical properties, processability, reliability, sustainability, and other factors should be more deeply understood.

Therefore, in this Special Issue of Polymers we would like to collect contributions that focus on (but are not limited to) the design, fabrication, structural and functional regulation, as well as application of various polymeric membranes in boosting the utilization of membrane materials in environmental science. Submissions in the form of full-length articles, communications, and reviews are invited.

Dr. Yan Wang
Prof. Dr. Gang Wei
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Polymers is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2700 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • functional polymers
  • fabrication technique
  • nanoparticles
  • 2D materials
  • functionalization
  • hybridization
  • biomimetic synthesis
  • characterization techniques
  • membrane filtration
  • wastewater treatment
  • desalination
  • environment remediation
  • drug
  • pesticides
  • virus
  • antifouling
  • antibacterial
  • sustainability

Published Papers (8 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

Article
Alginate/PVA Polymer Electrolyte Membrane Modified by Hydrophilic Montmorillonite for Structure and Selectivity Enhancement for DMFC Application
Polymers 2023, 15(12), 2590; https://doi.org/10.3390/polym15122590 - 06 Jun 2023
Cited by 2 | Viewed by 795
Abstract
Nafion is a commercial membrane that is widely used in direct methanol fuel cells (DMFC) but has critical constraints such as being expensive and having high methanol crossover. Efforts to find alternative membranes are actively being carried out, including in this study, which [...] Read more.
Nafion is a commercial membrane that is widely used in direct methanol fuel cells (DMFC) but has critical constraints such as being expensive and having high methanol crossover. Efforts to find alternative membranes are actively being carried out, including in this study, which looks at producing a Sodium Alginate/Poly (Vinyl Alcohol) (SA/PVA) blended membrane with modification by montmorillonite (MMT) as an inorganic filler. The content of MMT in SA/PVA-based membranes varied in the range of 2.0–20 wt% according to the solvent casting method implemented. The presence of MMT was seen to be most optimal at a content of 10 wt%, achieving the highest proton conductivity and the lowest methanol uptake of 9.38 mScm−1 and 89.28% at ambient temperature, respectively. The good thermal stability, optimum water absorption, and low methanol uptake of the SA/PVA-MMT membrane were achieved with the presence of MMT due to the strong electrostatic attraction between H+, H3O+, and OH ions of the sodium alginate and PVA polymer matrices. The homogeneous dispersion of MMT at 10 wt% and the hydrophilic properties possessed by MMT contribute to an efficient proton transport channel in SA/PVA-MMT membranes. The increase in MMT content makes the membrane more hydrophilic. This shows that the loading of 10 wt% MMT is very helpful from the point of view of sufficient water intake to activate proton transfer. Thus, the membrane produced in this study has great potential as an alternative membrane with a much cheaper cost and competent future performance. Full article
Show Figures

Figure 1

Article
Effect of Solvent and Monomer Ratio on the Properties of Polyphenylene Sulphone
Polymers 2023, 15(10), 2279; https://doi.org/10.3390/polym15102279 - 12 May 2023
Viewed by 615
Abstract
For the first time, the effect of the solvent and monomer ratio on molecular weight, chemical structure, and mechanical, thermal, and rheological characteristics of polyphenylene sulfone has been studied. When dimethylsulfoxide (DMSO) is used as a solvent, cross-linking occurs during the processing of [...] Read more.
For the first time, the effect of the solvent and monomer ratio on molecular weight, chemical structure, and mechanical, thermal, and rheological characteristics of polyphenylene sulfone has been studied. When dimethylsulfoxide (DMSO) is used as a solvent, cross-linking occurs during the processing of the polymer, which is accompanied by an increase in melt viscosity. This fact sets a pressing need for the complete removal of DMSO from the polymer. The best solvent used for the production of PPSU is N,N-dimethylacetamide. This study of the molecular weight characteristics of polymers by gel permeation chromatography showed the stability of the polymers practically does not change with a decrease in molecular weight. The synthesized polymers correspond in tensile modulus to the commercial analog Ultrason-P, while exceeding it in terms of tensile strength and relative elongation at break. Thus, the developed polymers are promising for spinning hollow fiber membranes with a thin selective layer. Full article
Show Figures

Figure 1

Article
Solvent-Evaporation-Induced Synthesis of Graphene Oxide/Peptide Nanofiber (GO/PNF) Hybrid Membranes Doped with Silver Nanoparticles for Antibacterial Application
Polymers 2023, 15(5), 1321; https://doi.org/10.3390/polym15051321 - 06 Mar 2023
Viewed by 1127
Abstract
Designing functional membranes through the collaboration of multi-dimensional nanomaterials is of particular interest in environmental and biomedical applications. Herein, we propose a facile and green synthetic strategy by collaborating with graphene oxide (GO), peptides, and silver nanoparticles (AgNPs) to synthesize functional hybrid membranes [...] Read more.
Designing functional membranes through the collaboration of multi-dimensional nanomaterials is of particular interest in environmental and biomedical applications. Herein, we propose a facile and green synthetic strategy by collaborating with graphene oxide (GO), peptides, and silver nanoparticles (AgNPs) to synthesize functional hybrid membranes with favourable antibacterial effects. GO nanosheets are functionalized with self-assembled peptide nanofibers (PNFs) to form GO/PNFs nanohybrids, in which the PNFs not only improve the biocompatibility and dispersity of GO, but also provide more active sites for growing and anchoring AgNPs. As a result, multifunctional GO/PNFs/AgNP hybrid membranes with adjustable thickness and AgNP density are prepared via the solvent evaporation technique. The structural morphology of the as-prepared membranes is characterized using scanning electron microscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy, and their properties are analyzed by spectral methods. The hybrid membranes are then subjected to antibacterial experiments and their excellent antibacterial performances are demonstrated. Full article
Show Figures

Figure 1

Article
Investigation of Performance of Anion Exchange Membrane (AEM) Electrolysis with Different Operating Conditions
Polymers 2023, 15(5), 1301; https://doi.org/10.3390/polym15051301 - 04 Mar 2023
Cited by 3 | Viewed by 1648
Abstract
In this work, the performance of anion exchange membrane (AEM) electrolysis is evaluated. A parametric study is conducted, focusing on the effects of various operating parameters on the AEM efficiency. The following parameters—potassium hydroxide (KOH electrolyte concentration (0.5–2.0 M), electrolyte flow rate (1–9 [...] Read more.
In this work, the performance of anion exchange membrane (AEM) electrolysis is evaluated. A parametric study is conducted, focusing on the effects of various operating parameters on the AEM efficiency. The following parameters—potassium hydroxide (KOH electrolyte concentration (0.5–2.0 M), electrolyte flow rate (1–9 mL/min), and operating temperature (30–60 °C)—were varied to understand their relationship to AEM performance. The performance of the electrolysis unit is measured by its hydrogen production and energy efficiency using the AEM electrolysis unit. Based on the findings, the operating parameters greatly influence the performance of AEM electrolysis. The highest hydrogen production was achieved with the operational parameters of 2.0 M electrolyte concentration, 60 °C operating temperature, and 9 mL/min electrolyte flow at 2.38 V applied voltage. Hydrogen production of 61.13 mL/min was achieved with an energy consumption of 48.25 kW·h/kg and an energy efficiency of 69.64%. Full article
Show Figures

Figure 1

Article
Effect of OH-Group Introduction on Gas and Liquid Separation Properties of Polydecylmethylsiloxane
Polymers 2023, 15(3), 723; https://doi.org/10.3390/polym15030723 - 31 Jan 2023
Viewed by 1498
Abstract
Membrane development for specific separation tasks is a current and important topic. In this work, the influence of OH-groups introduced in polydecylmethylsiloxane (PDecMS) was shown on the separation of CO2 from air and aldehydes from hydroformylation reaction media. OH-groups were introduced to [...] Read more.
Membrane development for specific separation tasks is a current and important topic. In this work, the influence of OH-groups introduced in polydecylmethylsiloxane (PDecMS) was shown on the separation of CO2 from air and aldehydes from hydroformylation reaction media. OH-groups were introduced to PDecMS during hydrosilylation reaction by adding 1-decene with undecenol-1 to polymethylhydrosiloxane, and further cross-linking. Flat sheet composite membranes were developed based on these polymers. For obtained membranes, transport and separation properties were studied for individual gases (CO2, N2, O2) and liquids (1-hexene, 1-heptene, 1-octene, 1-nonene, heptanal and decanal). Sorption measurements were carried out for an explanation of difference in transport properties. The general trend was a decrease in membrane permeability with the introduction of OH groups. The presence of OH groups in the siloxane led to a significant increase in the selectivity of permeability with respect to acidic components. For example, on comparing PDecMS and OH-PDecMS (~7% OH-groups to decyl), it was shown that selectivity heptanal/1-hexene increased eight times. Full article
Show Figures

Figure 1

Article
Parametric Study and Electrocatalyst of Polymer Electrolyte Membrane (PEM) Electrolysis Performance
Polymers 2023, 15(3), 560; https://doi.org/10.3390/polym15030560 - 21 Jan 2023
Cited by 2 | Viewed by 1932
Abstract
An investigation was conducted to determine the effects of operating parameters for various electrode types on hydrogen gas production through electrolysis, as well as to evaluate the efficiency of the polymer electrolyte membrane (PEM) electrolyzer. Deionized (DI) water was fed to a single-cell [...] Read more.
An investigation was conducted to determine the effects of operating parameters for various electrode types on hydrogen gas production through electrolysis, as well as to evaluate the efficiency of the polymer electrolyte membrane (PEM) electrolyzer. Deionized (DI) water was fed to a single-cell PEM electrolyzer with an active area of 36 cm2. Parameters such as power supply (50–500 mA/cm2), feed water flow rate (0.5–5 mL/min), water temperature (25−80 °C), and type of anode electrocatalyst (0.5 mg/cm2 PtC [60%], 1.5 mg/cm2 IrRuOx with 1.5 mg/cm2 PtB, 3.0 mg/cm2 IrRuOx, and 3.0 mg/cm2 PtB) were varied. The effects of these parameter changes were then analyzed in terms of the polarization curve, hydrogen flowrate, power consumption, voltaic efficiency, and energy efficiency. The best electrolysis performance was observed at a DI water feed flowrate of 2 mL/min and a cell temperature of 70 °C, using a membrane electrode assembly that has a 3.0 mg/cm2 IrRuOx catalyst at the anode side. This improved performance of the PEM electrolyzer is due to the reduction in activation as well as ohmic losses. Furthermore, the energy consumption was optimal when the current density was about 200 mA/cm2, with voltaic and energy efficiencies of 85% and 67.5%, respectively. This result indicates low electrical energy consumption, which can lower the operating cost and increase the performance of PEM electrolyzers. Therefore, the optimal operating parameters are crucial to ensure the ideal performance and durability of the PEM electrolyzer as well as lower its operating costs. Full article
Show Figures

Graphical abstract

Article
Self-Powered Gradient Hydrogel Sensor with the Temperature-Triggered Reversible Adhension
Polymers 2022, 14(23), 5312; https://doi.org/10.3390/polym14235312 - 05 Dec 2022
Cited by 1 | Viewed by 955
Abstract
The skin, as the largest organ of human body, can use ions as information carriers to convert multiple external stimuli into biological potential signals. So far, artificial skin that can imitate the functionality of human skin has been extensively investigated. However, the demand [...] Read more.
The skin, as the largest organ of human body, can use ions as information carriers to convert multiple external stimuli into biological potential signals. So far, artificial skin that can imitate the functionality of human skin has been extensively investigated. However, the demand for additional power, non-reusability and serious damage to the skin greatly limits applications. Here, we have developed a self-powered gradient hydrogel which has high temperature-triggered adhesion and room temperature-triggered easy separation characteristics. The self-powered gradient hydrogels are polymerized using 2-(dimethylamino) ethyl metharcylate (DMAEMA) and N-isopropylacrylamide (NIPAM) under unilateral UV irradiation. The prepared hydrogels achieve good adhesion at high temperature and detachment at a low temperature. In addition, according to the thickness-dependent potential of the gradient hydrogel, the hydrogels can also sense pressure changes. This strategy can inspire the design and manufacture of self-powered gradient hydrogel sensors, contributing to the development of complex intelligent artificial skin sensing systems in the future. Full article
Show Figures

Figure 1

Article
Synthesis of Amidoxime Adsorbent by Radiation-Induced Grafting of Acrylonitrile/Acrylic Acid on Polyethylene Film and Its Application in Pb Removal
Polymers 2022, 14(15), 3136; https://doi.org/10.3390/polym14153136 - 01 Aug 2022
Cited by 4 | Viewed by 1343
Abstract
In the aquatic environment, heavy metals such as lead ions Pb (II) are of particular importance. These are due to Pb (II) being toxic at concentrations over 0.01 mg/L, when taken continuously over an extended length of time. Organs including the heart, gut, [...] Read more.
In the aquatic environment, heavy metals such as lead ions Pb (II) are of particular importance. These are due to Pb (II) being toxic at concentrations over 0.01 mg/L, when taken continuously over an extended length of time. Organs including the heart, gut, and kidneys are seriously harmed by Pb (II) intoxication. The neurological, reproductive, and bone systems are also affected. The removal of Pb (II) from aquatic environments is, therefore, crucial. Low density Polyethylene (LDPE) is grafted by radiation with Acrylonitrile and acrylic acid (PE-g-AN/AAc) for the adsorption of Pb (II). Factors that control the grafting process for optimum conditions, such as the effect of solvents, the air atmosphere, inhibitors, comonomer concentration, and composition and irradiation dose, are studied to obtain a high grafting yield without homopolymer formation and a higher water uptake. The results showed that the addition of 2.5% by wt% ferric chloride salt effectively inhibits homoploymerization of a mixture of 30% methanol and 70% H2O used as a solvent in nitrogen. The highest graft yield obtained was 320% at a 25 kGy radiation dose with an 80/20 monomer composition and 60% comonomer concentration. The resulting composite films were characterized by XRD to analyze the dispersion properties of the material, SEM for the surface morphology, FTIR analysis for the functional groups, TGA, DSC for the thermal stability and elongation, and tensile strength for the mechanical properties. The uptake of Pb (II) from lead nitrate aqueous solution by (PE-g-AN/AAc) was observed under different conditions of the degree of grafting, contact time, metal ion concentration, and pH. The results obtained suggest LDPE-g-p (AN/AAc) as a superabsorbent for the Pb (II) ion’s removal from an aqueous solution. Full article
Show Figures

Figure 1

Back to TopTop