Plastic Deformation and Welding on Metallic Materials

A special issue of Crystals (ISSN 2073-4352). This special issue belongs to the section "Crystalline Metals and Alloys".

Deadline for manuscript submissions: 30 December 2024 | Viewed by 148

Special Issue Editors


E-Mail Website
Guest Editor
Department of Logistics and Management Engineering, Institute of Applied Sciences, Faculty of WSB University in Chorzow, WSB University in Poznan, 29 Sportowa Str., 41-506 Chorzow, Poland
Interests: production engineering; process optimization; manufacturing processes; materials engineering; plastic deformation; materials characterisation; welding; coatings
Special Issues, Collections and Topics in MDPI journals

E-Mail Website
Guest Editor
Department of Welding Engineering, Faculty of Mechanical Engineering, Silesian University of Technology, Konarskiego 18A Str., 44-100 Gliwice, Poland
Interests: laser surface engineering; laser material processing; welding; coatings; the additive manufacturing of metal parts
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

One of the most important properties of metals and alloys is their ability to deform permanently without breaking cohesion, known as plasticity. It is this property that makes possible the plastic processing of metals in processes including rolling, forging, pressing, drawing, and obtaining finished products and semi-finished products such as rods, profiles, sheets, pipes, and wires. The functional properties of structural materials, especially their mechanical characteristics, are significantly influenced by the chemical composition of the alloy, the manufacturing technology, and the heat and plastic processing used, which determine the material's crystalline structure and macro- and microstructure, as well as the presence or absence of texture. In this Special Issue, we will focus on the effect of the cold and hot plastic deformation process on changes in the structure and properties of modern and advanced metallic materials (i.e., Austenitic stainless steel–ASS, High-Strength Low-Alloy–HSLA, low-carbon high-Mn TWIP steel, high-manganese austenitic steel, non-ferrous alloys, and others). In addition, in this issue we will address the welding of advanced materials and, therefore, their joining technologies to ensure high-quality joints and high mechanical properties of the obtained joints. 

We are pleased to invite you to submit original research papers, short communications, or review articles that describe the current state of knowledge in the field of Plastic Deformation and Welding of Metallic Materials. 

Research areas may include (but are not limited to) the following:

- Characterization of deformed materials (microstructure, texture, mechanical properties, etc.).

- Characterization of welded materials (microstructure, mechanical properties, etc.).

- Welding of metallic materials.

- Advanced fusion and solid-state welding technologies of materials.

Dr. Agnieszka Kurc-Lisiecka
Prof. Dr. Aleksander Lisiecki
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Crystals is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • plastic deformation
  • hot working
  • cold working
  • welding
  • innovative methodology research
  • new technologies
  • physical and numerical simulation of plastic deformation
  • structure and mechanical properties

Published Papers

This special issue is now open for submission.
Back to TopTop