Analytica

Electrical conductivity is one of the main parameters for the characterization of water solutions and for the monitoring of water sources. In this paper, we describe a very inexpensive prototype for conductivity measurements based on Arduino UNO R3 coupled to an open-source circuit board with only passive components. We designed the printed circuit board (PCB) and the suitable handmade cell using stainless-steel electrodes and wrote the freeware management software; the assembly of the prototype, including a temperature probe, and results were relatively simple. In order to allow for replicates, the instrument design, schematics, and software are available with an open-source license. Thirty-one bottles of spring waters with conductivities of between 15.2 and 2000 µS cm⁻¹ were tested using both this prototype and a commercial conductivity meter. Data correlation produced an equation that allowed us to obtain the conductivity value, starting with the value furnished by the Arduino apparatus in arbitrary units. The prototype is accurate enough (inaccuracy lower than 6% excluding very low conductivity values) and precise (RSD% of about 5%). Even if a lot of commercial instruments for conductivity are available, we propose a prototype built with the aim of lowering the cost of measurements, while ensuring that they remain useful for lab or in situ application, as well as for continuous water monitoring/management systems. A further aim was to propose the building of the instrument as a laboratory exercise; this can help students to better understand basic theoretical concepts regarding conductivity, electronic components, and the acquisition and treatment of analytical data. Full article

The adaptable nature of the SARS-CoV-2 virus has led to the emergence of multiple viral variants of concern. This research builds upon a previous demonstration of sampling human hand odor to distinguish SARS-CoV-2 infection status in order to incorporate considerations of the disease variants. This study demonstrates the ability of human odor expression to be implemented as a non-invasive medium for the differentiation of SARS-CoV-2 variants. Volatile organic compounds (VOCs) were extracted from SARS-CoV-2-positive samples using solid phase microextraction (SPME) coupled with gas chromatography–mass spectrometry (GC–MS). Sparse partial least squares discriminant analysis (sPLS-DA) modeling revealed that supervised machine learning could be used to predict the variant identity of a sample using VOC expression alone. The class discrimination of Delta and Omicron BA.5 variant samples was performed with 95.2% (±0.4) accuracy. Omicron BA.2 and Omicron BA.5 variants were correctly classified with 78.5% (±0.8) accuracy. Lastly, Delta and Omicron BA.2 samples were assigned with 71.2% (±1.0) accuracy. This work builds upon the framework of non-invasive techniques producing diagnostics through the analysis of human odor expression, all in support of public health monitoring. Full article

This review provides insights into the current research on pyrolytic bio-oil obtained from different feedstock regarding upgrading techniques and applications such as energy, fuels, chemicals, and carbon materials. Raw bio-oil is not appropriate for transportation and ignition due to undesired properties; therefore, several challenges have been reported regarding its suitable market application. For liquid biofuel production, thermochemical pathways, particularly hydrogenation and deoxygenation, must be carried out, and for chemical production, liquid solvents are mostly used via physical separation. The main issues related to downstream processes with environmental and economic assessment are also covered. The analysis indicates that the major bottlenecks for commercial applications of upgraded bio-oil are the initial stage (upgrading techniques), high production costs, and pilot scale production. Finally, future directions are addressed for the improvement of bio-oil upgrading. Full article

Achieving quantification of biomarkers in body fluids is crucial to the indication of the state of a person’s body and health. Wearable sensors could offer a convenient, fast and painless sensing strategy. In this work, we fabricated a wearable electrochemical patch sensor for simultaneous detection of dopamine and glucose in sweat. The sensor was printed on a flexible PDMS substrate with a simple screen-printed method. This prepared four-electrode sensor integrated two working electrodes for dopamine and glucose electrochemical sensing, one Ag/AgCl reference electrode and one carbon counter electrode, respectively. Cyclic voltammetry, differential pulse voltammetry and chronoamperometry were used for the evaluation of the wearable electrochemical patch sensor. It exhibits good sensitivity, wide linear range, low limit of detection, good anti-interference and reproducibility toward dopamine and glucose sensing in PBS and sweat. Full article

This work proposes a simple, fast and low-cost voltammetric method for the determination of trimethoprim at low concentrations in an analytical and real matrix (river water sample, bovine serum and synthetic urine). For this, a glassy carbon electrode was modified with Printex(6L) carbon and gold nanoparticles in a chitosan film crosslinked with epichlorohydrin. After that, the electrochemical measurement system contained a solution of phosphate buffer at pH 4.0 with commands for the square wave voltammetry technique. The results achieved showed a limit of detection equal to 12.4 nmol L⁻¹ and a linear concentration range from 0.20 to 6.0 μmol L⁻¹. The sensor selectivity was tested in the presence of various electroactive molecules, and the results showed that the detection of TMP in the presence of possible interferents was not masked. In addition, the applicability of the AuNPs–Printex(6L)–CTS:EPH/GCE sensor was also verified in synthetic samples of urine, bovine serum and river water through standard addition and recovery tests. Finally, the results of this analytical proposal portray a simple, fast and efficient method for the detection of TMP in different matrices. Full article

Ximenia americana L., popularly known in Brazil as “ameixa do-mato, ameixa-brava, and ameixa-do-sertão,” is widely used in folk medicine to treat several intestinal disorders. The present study assessed the potential mechanisms of action underlying the gastroprotective activity of the hydroethanolic extract of Ximenia americana L. (EHXA) stem bark. The acute toxicity of EHXA was estimated, and later, the gastroprotective effect in mice was assessed through acute models of gastric lesions induced by acidified or absolute ethanol and indomethacin, where the following mechanisms were pharmacologically analyzed: the involvement of prostaglandins (PG), histamine (H₂) receptors, ATP-dependent potassium channels, sulfhydryl groups (SH), α₂ adrenergic receptors, nitric oxide (NO), myeloperoxidase (MPO), gastric mucus production, and acetylcholine-mediated intestinal motility. Regarding toxicity, EHXA did not cause deaths or signs of toxicity (LD₅₀ greater than or equal to 2000 mg/kg/p.o.). When the gastroprotective effect was assessed, EHXA (50, 100, and 200 mg/kg/p.o.) reduced the rate of lesions induced by acidified ethanol by 65.63; 53.66, and 58.02% in absolute ethanol at 88.91, 78.82, and 74.68%, respectively, when compared to the negative control group. In the indomethacin-induced gastric injury model, the reductions were 84.69, 55.99, 55.99, and 42.50%, respectively. The study revealed that EHXA might stimulate mucus production and reduce intestinal motility through SH groups, NO production, and activation of α₂ adrenergic receptors. The results indicated that EHXA had significant gastroprotective activity in the evaluated models. However, further investigation is required to elucidate the cellular and molecular events underlying the action of EHXA components and to correlate them with the modulation of the signaling pathways, as demonstrated by the current pharmacological approach. Therefore, the results demonstrated in the present study, as well as previously reported findings, support the recommendation of using this species in traditional communities in Brazil. Full article

Different starch properties may cause alterations in the foodstuff’s external appearance. However, modification processes in starches are usually secretive. The use of chemically modified starches is regulated by international standards, which makes it important to identify its presence and type. Mid-infrared spectroscopy (MIR)-modified starches’ identification can be hindered by the presence of excess glucose. This research investigates types of modification in commercial starches and in approaches that circumvent MIR’s limitations with exploratory analysis. It also considers that enzymatic hydrolysis (α-amylase and amyloglucosidase) can highlight the points of modification in the structure, which can be detected with infrared assays. To determine if sour cassava starch (FCS) is modified and check its type, six samples were selected: a native one, three of the most common cassava modified starches (etherified, esterified, and FCS), and two laboratory processed samples (Acid, Oxidized). The results showed that the sour cassava starch showed similarities with a commercial ester and an oxidized cassava starch, which may be due to the formation of a graft, corresponding to what the literature has already reported for corn starch treated with lactic acid and gamma radiation. Full article

Here, we present proof of principle studies to demonstrate how the product ions associated with the ion mobility peaks obtained from a High Kinetic Energy-Ion Mobility Spectrometer (HiKE-IMS) measurement of a volatile can be identified using a Proton Transfer Reaction/Selective Reagent Ion-Time-of-Flight-Mass Spectrometer (PTR/SRI-ToF-MS) when operating both instruments at the same reduced electric field value and similar humidities. This identification of product ions improves our understanding of the ion chemistry occurring in the ion source region of a HiKE-IMS. The combination of the two analytical techniques is needed, because in the HiKE-IMS three reagent ions (NO⁺, H₃O⁺ and O₂^+•) are present at the same time in high concentrations in the reaction region of the instrument for reduced electric fields of 100 Td and above. This means that even with a mass spectrometer coupled to the HiKE-IMS, the assignment of the product ions to a given reagent ion to a high level of confidence can be challenging. In this paper, we demonstrate an alternative approach using PTR/SRI-ToF-MS that allows separate investigations of the reactions of the reagent ions NO⁺, H₃O⁺ and O₂^+•. In this study, we apply this approach to four nitrile containing organic compounds, namely acetonitrile, 2-furonitrile, benzonitrile and acrylonitrile. Both the HiKE-IMS and the PTR/SRI-ToF-MS instruments were operated at a commonly used reduced electric field strength of 120 Td and with gas flows at the same humidities. Full article

Chlorine-containing disinfectants have been widely used all over the world to prevent COVID-19. However, little is known about the potential risk of chlorine-containing disinfectants in the marine environment. Phaeodactylum tricornutum (P. tricornutum) is a typical marine economic diatom, often used as an effective biomarker in ecotoxicology research. Here, the present study has investigated the effect of different effective chlorine concentrations on photosynthesis of P. tricornutum by chlorophyll fluorescence spectroscopy. Results have demonstrated that chlorine exposure promoted the chlorophyll fluorescence intensity at initial stage (24 h), suggesting that a large amount of energy is emitted in the form of fluorescence. However, the chlorophyll fluorescence intensity could not be detected under the high effective chlorine concentrations (6.7 × 10⁻³, 1.0 × 10⁻², 1.3 × 10⁻² and 1.7 × 10⁻² mg L⁻¹) after 48 h, indicating that the chlorine had high toxicity leading to the death of microalgae. In addition, the emission spectra of P. tricornutum were determined to contain two distinct fluorescence peaks representing the core antenna of photosystem II (685 nm) and the photosystem I complexes (710 nm) in the control group. The fluorescence emission peak value at 685 nm is significantly lower than the peak value at 710 nm in the control group, whereas chlorine treatments were opposite. It can be concluded that microalgae can regulate the distribution of excitation energy between the two photosystems to ensure that algae can utilize light energy. The result also found that the peak position of fluorescence emission spectra has a blue shift in all of NaClO treatments. The fluorescence intensity of microalgae excited at 467 nm was lower than that at 439 nm in chlorine treatments, illustrating chlorophyll b antenna was more easily damaged than chlorophyll a antenna. Our findings are providing new insights into the changing mechanism of chlorophyll fluorescence on P. tricornutum under chlorine stress and valuable data for risk assessment of marine environments. Full article

This study describes the preparation and use of a dental amalgam electrode for the voltammetric determination of triazine-based pesticides ametryn, atrazine, and simazine in natural waters, using square wave voltammetry. The experimental and voltammetric parameters were previously optimized, and analytical curves were constructed to calculate analytical parameters. The detection limits presented values that were lower than the maximum limits of residues permitted in natural water by the Brazilian Environmental Agency, 100 µg L⁻¹ (100 ppb), and around the values obtained using other electrodic surfaces or high-performance liquid chromatography, traditionally used in triazine levels determination. Furthermore, the recovery percentages in pure electrolyte and natural waters were around 100%, demonstrating that the methodology proposed is suitable for determining triazines contamination in natural water samples, based on an environmentally friendly procedure. Full article

Among many diseases, allergy appears to be a serious problem for human beings. Various forms of allergic disorders make people tense, leading to some other health issues. Many medications, including nonracemic and racemic ones, are used to treat this problem. It is important to have exact analysis strategies just to see any medication side effects, plasma profiles, and working efficiency. Therefore, efforts are made to review simple and chiral HPLC methods for antiallergic drugs; HPLC is the best analytical technique. The highlights in this article include the world scenario, causes of allergy, the effect of allergy on the economy, the mechanism of allergy in humans, classes of antiallergic drugs, simple drugs, chiral drugs, analysis by HPLC, and the chiral recognition mechanism. Moreover, attempts are also made to highlight the management of allergies and future perspectives. Full article

Human milk provides all the nutrients required by babies during the first six months of their life. Human milk lipids represent the main source of energy, contributing almost 50% of the total energy content. Additionally, fatty acids ensure the correct development of children in the prenatal, postnatal, and infant phases. Docosahexaenoic acid (DHA) is essential for visual and cognitive development, and its presence during childhood can affect long-term health. This study aimed to optimize and validate a methodology for the direct determination of DHA in human milk. We used 20 samples of human milk from lactating women living in the city of Itu, São Paulo, who attended Basic Health Units from September 2019 to September 2020, and a sample of certified reference material from the National Institute of Standards and Technology. The proposed methodology consists of a validated mixed transesterification process without prior lipid extraction, optimized by factorial design. This methodology can be successfully used in human milk samples as it is both precise and accurate. The values of DHA in the sampled milks were similar to those in European countries and lower than those in Asian countries due to diet. Full article

Chromatograms with overlapping peaks and a baseline rise or upset constitute a great challenge for analysts. Such a case regarding the analysis of bupropion hydrochloride and its 5 impurities in a tablet formulation was used as a model. A baseline correction technique for liquid chromatography coupled with diode array detection is described by using Rstudio. The asymmetry least squares (ALS) algorithm was used as implemented in the “baseline” package, with parameters lambda and p set to 4 and 0.05, respectively. Peak deconvolution and subsequent integration and area quantification were accomplished through Fytik software. Chromatographic data from the validation procedure were utilized to demonstrate the feasibility of the suggested method and whether this correction affects the outcome of the validation study. Finally, a robustness study was carried out in order to shed light on the factors that have a more significant influence on the baseline correction, showing the reliability of this procedure through random changes in its parameters. Full article

Fluorescent staining of microplastics as a detection method is consistently gaining importance in microplastics research, as it is fast, easy to use, and requires low technical effort. In this study, a complete procedure was developed, from sample collection to sample processing and detection, to measure microplastics with low cost and time requirements. The developed procedure was tested by measuring the microplastics in the effluent of a German wastewater treatment plant over a period of one year. The results show that the process is especially well suited to investigate temporal variations of microplastic contamination, which requires a large number of samples to be processed. Further, the precision and selectivity of the detection process could be improved by applying newly developed Nile red derivatives for fluorescent staining. A low budget modification of a microscope for fluorescent imaging is compared to a modification with precise optical bandpass filters. A script enabling automated microplastic detection and counting was developed, improving the accuracy and comparability of the process. Full article

Global plastic production and usage has increased annually for decades and microplastic pollutants (≤5 mm) are a growing concern. Microplastics in surface waters can adsorb and desorb harmful chemicals such as per- and polyfluoroalkyl substances (PFAS). Microplastics can accumulate across all tropic levels in the marine food web. The purpose of this research was to analyze the stomach and intestinal contents of stranded (Mississippi coast) bottlenose dolphins and sea turtles for the presence of microplastics and commonly found PFAS, PFOS, PFOA, and GenX. Gut contents were digested (10% KOH in 50% MeOH) and then analyzed for microplastics using pyrolysis gas chromatography-mass spectrometry (Pyro-GC-MS), Nile red microscopy, X-ray photo electron spectroscopy (XPS), and Raman spectroscopy. Digested sample filtrate was pre-concentrated using solid-phase extraction (SPE) before PFAS liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis. The PFOS extraction and analysis had 98.6% recovery when validated with certified pike‒perch fish reference material. The Nile red testing on most samples revealed the presence of microplastics (Table S1). The Pyro-GC-MS results from two samples confirmed the presence of the plasticizer acetamide. The Raman spectroscopy analysis indicated characteristic plastic peaks corresponding to polystyrene in one sample. PFOS (95.5 to 1,934.5 µg/kg) was detected in three dolphin stomach samples. This project is part of a long-term study with the goal of a better understanding of microplastics and PFAS environmental contamination and their impact on bottlenose dolphins and sea turtles. Full article

Levetiracetam (LEV) is a broad spectrum antiseizure medication that is used in various seizure types. There is evidence that therapeutic drug monitoring (TDM) of LEV is of value in selected patient populations, therefore determination of LEV plasma concentrations is essential. Herein we developed and validated a simple, reproducible, and practical method for the quantification of LEV concentrations in human plasma samples using high performance liquid chromatography (HPLC). Plasma samples (0.3 mL) deproteinization was done using acetonitrile. HPLC chromatographic separation of plasma samples was accomplished by reversed phase C18 column. The mobile phase constituted water and acetonitrile (90:10, v/v) ran at flow rate of 1 mL/min. Signal acquisition was conducted at a wavelength of 192 nm. Calibration curves showed excellent linearity (Correlation coefficient r² > 0.99) over a concentration range of 3–80 μg/mL. Both inter and intraday assay accuracy and precision were less than 8% (except for the lowest limit of quantification was within 20%). Elution time was 15 min. The developed method excluded the use of buffers and utilized small volumes of plasma samples with simple mobile phase composition. Therefore, our method could be practically applied to routine TDM. Full article

The body of work described in this research paper evaluates the compatibility between Fenbendazole (Fen), which is a broad-spectrum anthelmintic with promising antitumor activity, and three polymeric excipients commonly applied in pharmaceutical dosage forms. The assessment of binary mixtures was performed by differential scanning calorimetry and thermogravimetric analysis/derivative thermogravimetry to predict physical and/or chemical interactions, followed by X-ray diffraction spectroscopy (XRD), Fourier transform infrared spectroscopy (FTIR), and high-performance liquid chromatography (HPLC) to confirm or exclude any interactions. Thermal studies suggested the presence of interactions between Fen and P 407, PCL, and PLA. To validate these data, XRD showed that Fen is compatible with PCL and PLA, suggesting some interaction with P 407. FTIR demonstrated that PCL and PLA can establish physical interactions with Fen; moreover, it suggested that P 407 interacts not only physically but also chemically, which was later proved by HPLC to be only new intermolecular interactions. This work supports the further application of P 407, PCL, and PLA for the development of new medicinal and veterinary formulations containing Fen, since they do not affect the physical and chemical characteristics of the active ingredient and consequently its bioavailability and therapeutic efficacy. Full article

Green(er) sample preparation technologies still dominate as the anticipated improvement in all analytical protocols. Separation scientists all over the world continuously strive to comply with the Green Analytical Chemistry (GAC) demands. To follow this trend, microextraction techniques are constantly evolving to bridge the gap between Green Analytical Chemistry and sample pretreatment. A research group from Florida International University, Miami, Florida has introduced fabric phase sorptive extraction (FPSE) in 2014 that was considered as a new milestone in microextraction technologies at that time. Two years later, the same research group introduced an advantageous innovative configuration that combines the stirring and extraction mechanism into a single sample preparation device, keeping all the benefits originally offered by classical FPSE. Magnet integrated fabric phase sorptive extraction (MI-FPSE) was eventually introduced as a new, advantageous implementation of FPSE. This device exhibits the advantageous role of the increase in extraction kinetics through sample diffusion, resulting in improved extraction efficiency of the microextraction device and supports the need for combining processes for better promotion and implementation of the principles of Green Analytical Chemistry. The applications of MI-FPSE are presented herein, showing the essential role that this technique can play in analytical and bioanalytical sample preparation. Full article