Next Article in Journal
Effects of Dispersed Carbon Nanotubes and Emerging Supramolecular Structures on Phase Transitions in Liquid Crystals: Physico-Chemical Aspects
Previous Article in Journal
Translational Dynamics of Imidazolium-Based Ionic Liquids in Acetonitrile Solutions
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Determination of the Dissociation Constants (pKa) of Eight Amines of Importance in Carbon Capture: Computational Chemistry Calculations, and Artificial Neural Network Models

by
Venkata Sai Priyatham Varma Alluri
,
William (Hoang Chi Hieu) Nguyen
and
Amr Henni
*
Clean Energy Technologies Research Institute (CETRi), Acid Gas Removal Laboratory (AGRL), Faculty of Engineering and Applied Science, University of Regina, Regina, SK S4S 0A2, Canada
*
Author to whom correspondence should be addressed.
Liquids 2023, 3(2), 214-245; https://doi.org/10.3390/liquids3020016
Submission received: 11 April 2023 / Revised: 28 April 2023 / Accepted: 8 May 2023 / Published: 20 May 2023
(This article belongs to the Section Chemical Physics of Liquids)

Abstract

:
This work focuses on determining the dissociation constants (pKa) of eight amines, namely, 3-(Diethylamino) propylamine, 1,3-Diaminopentane, 3-Butoxypropylamine, 2-(Methylamino) ethanol, Bis(2-methoxyethyl) amine, α-Methylbenzylamine, 2-Aminoheptane, and 3-Amino-1-phenylbutane, within temperatures ranging from 293.15 K to 323.15 K. The thermodynamic properties of the protonated reactions were regressed from the pKa work. In addition, the protonated order of both 3-(Diethylamino) propylamine and 1,3-Diaminopentane were determined using computational chemistry methods owing to their unsymmetrical structures. In addition to the experimental methods, the dissociation constants at the standard temperature (298.15 K) were also estimated using group functional models (paper–pencil) and computational methods. The computational methods include COSMO-RS and computational chemistry calculations. An artificial neural network (ANN) method was employed to model the data by collecting and combining the experimental properties to estimate the missing pKa values. Although the ANN models can provide acceptable results, they depend on the availability of the data. Instead of using the experimental properties, they were generated using software such as Aspen Plus or CosmothermX. The simulated ANN model can also provide very good fits to the experimental constant values.

1. Introduction

Carbon dioxide (CO2) is mainly generated by burning fossil fuels for human daily activities such as power generation, heating demands, and from refineries, steel, and cement production plants. CO2 is considered one of the greenhouse gases that cause global warming [1]. There are many CO2 capture technologies, such as using liquid solvents or solid sorbents to separate CO2 from the other gases. For the flue gases with low CO2 partial pressures, the aqueous amine solutions have been used because the solutions can quickly react with CO2 while physical solvents are not very suitable to capture CO2 at low pressures. For the different amine types, the reaction mechanisms between the amines and CO2 are also very different [2]. As a result, the study of the protonation between amines and CO2 is necessary to understand the reaction mechanism as well as model gas solubility in the solution [3].
Chowdhury et al. [4] and Tomizaki et al. [5] studied and reported the dissociation constants (pKa) for cyclic amines, while Perrin [6] reported the dissociation constants for many alkanolamines. Both Versteeg et al. [7] and Sharma [8] studied the relationships between the dissociation constants and the reaction rate between CO2 and aqueous amine solutions. The pKa values of 2-(Butylamino)ethanol, m-Xylylenediamine, 3-Picolylamine, Isopentylamine, and 4-(Aminoethyl)-piperidine were recently measured and reported by Kumar et al. [9], while Nguyen et al. [10] reported the experimental values and explained the protonation mechanisms by computational chemistry calculation (DFT) for 1,4-Bis(3-aminipropyl) piperazine, 1,3-Bis(aminomethyl) cyclohexane, Tris(2-aminoethyl) amine, and 1-Amino-4-methyl piperazine. In addition, the constant values can be used to determine amines’ chemical and biological behaviors [9,10,11,12].
Some methods used to determine the dissociation constant values for amines include ultraviolet spectrophotometry, potentiometric titration, magnetic resonance, and conductimetric titration [13]. Among these methods, potentiometric titration is widely used because of its simplicity and convenience within the pH range of 2.00 to 11.00 [13,14,15]. In this study, the potentiometric titration method was used to determine and dissociation constant of Monoethanolamine (MEA), 3-(Diethylamino) propylamine, 1,3-Diaminopentane, 3-Butoxy-propylamine, 2-(Methylamino) ethanol, Bis(2-methoxyethyl) amine, α-Methylbenzylamine, 2-Aminoheptane, and 3-Amino-1-phenylbutane for the temperature range between 298.15 K to 313.15 K with an increment of 5 K. The average atmospheric pressure during the experiments was 95.8 (±0.8) kPa. The purpose of using monoethanolamine (MEA) is for validating the equipment. The compounds’ structures, suppliers, and purities are listed in Table 1.
Based on the structures in Table 1, the studied amines included two diamines (DEAPA and EP) and six monoamines (BPA, MAE, BMOA, PEA, AH, and APB). All six monoamines were primary or secondary amines that have high kinetic and CO2 uptakes. The diamines were primary and tertiary amines. In addition, instead of directly measuring the kinetic rates between the aqueous amine solutions with CO2, the dissociation constants (pKa) can be used to rank the reaction rates for the studied amines. Furthermore, the dissociation constant can be used for further modeling CO2 absorptions into the aqueous solutions. The studied amines are mainly monoamines and tertiary amines; therefore, they are expected to have lower heat of absorption than polyamines. As a result, these amines have a high potential for CO2 capture.

2. Chemicals, Apparatus, and Experimental Procedures

The nine amines, namely, Monoethanolamine (MEA) (≥99% in mass purity), 3-(Diethylamino) propylamine (DEAPA) (≥99% in mass purity), 1,3-Diaminopentane (EP) (98% in mass purity), 3-Butoxypropylamine (BPA) (99% in mass purity), 2-(Methylamino) ethanol (MAE) (≥98% in mass purity), Bis(2-methoxyethyl) amine (BMOA) (98% in mass purity), α-Methylbenzylamine (PEA) (99% in mass purity), 2-Aminoheptane (AH) (99% in mass purity), and 3-Amino-1-phenylbutane (APB) (98% in mass purity) were purchased from Sigma Aldrich.
To measure the pH of the aqueous amine solutions, a 270 Denver Instrument pH meter (Denver Instruments, Arvada, CO, USA) was used in the titration method. Three pH buffer solutions were purchased from VWR (Mississauga, ON, Canada) and used to calibrate the pH meter. Buffer solutions of 4.00, 7.00, and 10.00 were used, and the uncertainties supplied by the manufacturer (VWR) were 0.02, 0.00, and 0.01 for the 10.00, 7.00, and 4.00 buffer solutions, respectively. Table S1 in the Supporting Information (SI) section summarizes the calibration data for the pH meter.
The equipment and experimental procedures were validated by determining the pKa of monoethanolamine (MEA) and compared with the values in the literature [9,10,11,14,15]. Figure S1 in SI shows the comparisons of the dissociation constant values (pKa) of MEA between this study and the data from the literature and is compared in Table S4. Hydrochloric acid solution 0.100 N (±0.002 N) was purchased from VWR International for the titration process. Nitrogen with 99.99% mass purity was purchased from Linde (Mississauga, ON, Canada) for flushing the space on the top of amine solutions to replace oxygen (O2) and carbon dioxide (CO2) present in the environment. The temperature of the solution inside the amine-storing beaker was controlled by an external water bath. The uncertainty of the temperature was 0.01 K. The aqueous amines were mixed to have a concentration of 0.0100 M within ±0.0002 M. The solutions were stirred at least for 20 min before starting the experiments.
In the beginning, 50 mL of the mixing solution was transferred into the storing beaker which had a stirring magnetic bar. During the experiment, the stirring speed of the bar was maintained at 30 rpm. The experiment started when the solution reached equilibrium and the temperature and pH became stable. The initial pH values of the solutions at equilibrium conditions were recorded. The storing beaker was always closed during the experiment to avoid oxidative degradation or vaporization. At each step of the titration process, 0.5 mL of the acid was added to the aqueous solution while stirring with the magnetic bar. After 20 to 30 s, the pH values were recorded as the mixtures reached equilibrium.
Measured pH and the details of the calculated pKa values for MEA, before the thermodynamic corrections, are presented in Table S2. Table S3 shows the values of pKa before and after the correction for MEA at 298.15 K.

3. Calculation of Dissociation Constant (pKa)

To determine the dissociation constant values for the studied amines, the titration method was used to measure the pH of the solutions at each step after adding the acid to the solutions. The procedures employed are reported below to estimate the pKa values for MEA as well as the other amines. The protonated mechanism of MEA and water is represented in Equation (1). In Equation (2), {MEAH+} is the protonated MEA molecule and {MEA} is the monoethanolamine molecule. Equation (2) was used to determine the pKa values before the thermodynamic correction [10],
MEAH + + H 2 O   K a   MEA + H 3 O +
p K a M = pH + log { M E A H + } { M E A }
Equation (3) was used to calculate ionic strength (I), which is a function of the molecular concentration of ionization species (Ci) in the solution and the valency of species (zi). The extended Debye–Hückel activity coefficient (γ) was calculated using Equation (4) with the adjustable parameter ki. The value of the parameter was dependent on the ion sizes. The Supporting Information (SI) provides the details of the pKa calculations as well as thermodynamic corrections with the parameters of A and B from the literature [16] and the values of ki from Sumon et al. [17] Equation (5) was used to determine the true concentration of protonated MEA. For the first dissociation constant calculation, the value of I can be simply used as in Equation (3); however, the Albert et al. [13] method was used to determine I for the second pKa, as reported in the literature [10]. Equation (6) was used to determine the dissociation constant after the thermodynamic correction (TC).
I = 0.5 C i z i 2
γ i = 10 A z i 2 I 1 + B k i I
M E A H + = { M E A H + } γ i
pKa = pKaM − TC

4. Results and Discussion

Based on the calculation steps mentioned above and in the Supporting Information section, the results of the first dissociation constants of MEA and the eight studied amines are listed in Table S4. The first pKa values of MEA for various temperatures are also plotted in Figure S1 and reported in the SI section to compare them with the literature data. All the first dissociation constants of the studied amines and MEA are plotted in Figure 1.
First, the more negative values in Figure 1 have higher dissociation constant values. As the obtained data are reported in Table S4 and Figure 1, the six studied amines, namely, DEAPA, EP, APB, MAE, AH, and BPA, have higher dissociation constant values than MEA within the studied temperature range. Furthermore, two studied amines, BMOA and PEA, have lower constant values for the studied temperature range. In addition, AH has a high slope of the linear regression line which implies that the kinetic of the amine strongly depended on the temperature and the concentration. The six amines with higher pKa values than MEA were expected to have higher reaction rates with CO2 than MEA.
In addition, among the eight studied amines, two were diamines, DEAPA and EP. The values of the second dissociation constant are reported in Table S5 and Figure 2. As shown, the second pKa of DEAPA was higher than that of EP. Based on the molecular structures of the two amines, DEAPA included one primary and one tertiary amino group, while EP had two primary amino groups. The tertiary amine tended to react slower with CO2 than the primary amine; however, DEAPA had a higher second pKa than EP, with two primary amino groups in the structure. Furthermore, tertiary amines have lower heat of absorption than primary amines. Therefore, DEAPA has great potential as an amine for CO2 capture.
The coefficients of determination (R2) of the linear regressions for Figure 1 and Figure 2 are reported in Table S6.
The standard state enthalpy change (ΔH0, kJ·mol−1) and entropy change (ΔS0, kJ·mol−1·K−1) can be determined using the van’t Hoff equation [9,10,15]. These thermodynamic quantities (ΔH0 and ΔS0) can be regressed using data in Tables S4 and S5 and Figure 1 and Figure 2 by applying Equation (7). In the equation, the slope and intercept of the linear regressions are ( Δ H 0 R ) and ( Δ S 0 R ), respectively. The universal gas constant (R, kJ·mol−1·K−1) value is 8.3145 × 10−3 kJ·mol−1·K−1. In addition, the standard state free energy of the reaction (ΔG0, kJ·mol−1) was calculated using Equation (8). The calculated values of these thermodynamic quantities are reported in Table 2, Table 3, Table 4 and Table 5.
ln   K a = ln   ( 10 p K a ) = Δ S 0 R + Δ H 0 R T
ΔG0 = RT ln (10pKa)

5. Estimation Protonated Order for the Diamines

There are two diamines in this study, namely, 3-(Diethylamino) propylamine and 1,3-Diaminopentane. As mentioned above, 3-(Diethylamino) propylamine’s structure has one primary and one tertiary amino group, while 1,3-Diaminopentane includes two unsymmetrical primary amino groups. It is important to know that the protonation order is required to model the solubility of CO2 in amine solutions. To perform the study, commercial computational chemistry software (Gaussian (09 Revision B.01 SMP)) was used to optimize the molecular structures of the neutral amines with different models and basis sets. The molecular structures of the amines were built by using GaussView version 5.0.9. The optimization model was performed with implicit (without explicit water molecule) solvent and polarizable continuum model (PCM) as default. Then, the optimization structures would be reoptimized with protons at different amino groups. The energy (E) of the protonated amines was used to suggest the preferred amino group for the first and second pKa. The structures with lower energies suggested the highest stable structures. For the computational chemistry methods, Hartree–Fock (HF), density functional theory (DFT/B3LYP), and the Moller–Plesset perturbation second order (MP2) were used. The basis sets chosen were 6-311G+(d,p), B3LYP/3-21G, and B3LYP/6-311G+(d,p), or HF, DFT, and DFT, respectively. For the MP2 calculation, the chosen basis set was 6-311G+(d,p). For the energy notation in Equation (9), E1 represented the potential energy surface (PES) when the proton was attached to the primary amino group on the carbon chain, while E2 represented the PES when the proton was attached to the primary amino group on the branch for (1,3-Diaminopentane) or the tertiary amino group for 3-(Diethylamino propylamine). The two geometrical structures for the two amines were optimized with water as a solvent and a polarizable continuum model (PCM).
ΔE (kJ·mol−1) = E1 − E2
Based on the results reported in Table 6, the differences in PES (ΔE/ kJ·mol−1) were positive for all calculation methods for 3-(Diethylamino) propylamine. This means that the E1 was higher than E2 or the protonated tertiary amino group was more stable than the protonated primary amino group in the structure. The results do not agree with what is reported in the literature [9,10,16], which suggested that the primary amino group should be protonated before the tertiary amino group. However, the functional groups in the structure can strongly affect the order of protonation for the amines. This conclusion will be studied further in the later parts of this study. As for 1,3-Diaminopentane, the differences were all negative; this implies that the protonated amino group on the chain structure was more stable than the protonated amino group on the branch.

6. Computational Estimation for the Dissociation Constants

In addition to the experimental measurements, the dissociation constants could be estimated by other methods such as the PDS [16] (Perrin, Dempsey, and Serjeant) method, the new PDS [17] method, the QSSG [18] method, the COSMO-RS method, the Van’t Hoff equation, the SHE [17] method, and the KHE [19] method. The first three methods were simply called functional group methods because the method suggested the base values for the primary, secondary, and tertiary groups. The functional groups around these amino groups would shift the base values. The shifted values depended on the type of functional groups and their positions. For the other methods, computational chemistry calculations were required to optimize the structure from which the Gibbs free energy would be determined before and after the protonation occurred. Based on the difference in the free energy, the values of dissociation constants can be determined.

6.1. Functional Group Estimations

The method can be used to estimate the first dissociation constant for the studied amines at 298.15 K based on the chemical structures. As mentioned above, the base values and the pKa shift were predetermined by optimizing the structures and the experimental values of many chemicals; as a result, the estimated values’ accuracies improved when more experimental values were available for optimization. For further improvements, Sumon et al. [17] and Qian et al. [18] included more data to reoptimize the base and shift values. Sumon’s method is called the new PDS while Qian’s method is called the QSSG method in this study. The suggested base and shift values for the three methods are summarized in Table S7. By applying these methods to determine the dissociation constant values for the studied amines, the first pKa at 298.15 K values are summarized in Table 7 below. 2-(Methylamino) ethanol was chosen to demonstrate the calculation method. Based on the structure in Table 1, this amine has a secondary amino group, (CH3)– on the secondary amino, and –(OH) on the gamma (γ) position. For the PDS method, the first pKa value of the amine would be 11.15 − 0.2 − 1.1 × 0.4 = 10.51. For the new PDS method, the first pKa value would be 10.50, while the QSSR method suggests 10.2. By comparing the estimated values with the experimental values (9.84), the lowest error was 0.36 while the highest error was 0.67. Table 7 summarizes the estimated pKa values for the three methods. As mentioned above, 3-(Diethylamino) propylamine and 1,3-Diaminopentane could be protonated at different locations; therefore, the superscript V1 was used to represent the primary amino protonating on the main chain while V2 stood for the tertiary amino or the branch primary amino protonating, as shown in Figure 3.

6.2. Computational Chemistry Estimation

In addition to the functional group estimations such as the PDS or QSSR methods, the dissociation constants values of the amines at the standard conditions can be estimated by computational chemistry calculations. In particular, the SHE [17] method applied quantum computational chemistry calculations to determine amine pKa values. In general, the dissociation mechanism of an amine was reported in Equation (10). By combing Equations (8) and (10), the dissociation constant at standard condition was determined by Equation (11) with R = 1.986 × 10−3 kcal·K−1·mol−1, and the unit of energy is kcal·mol−1. Equation (12) was derived by expanding and simplifying Equation (11) as reported in the literature [17]:
B H ( a q ) + B ( a q ) + H ( a q ) +
p K a = [ G a q H + + G a q B G a q B H + ] 1.3643
p K a = [ G a q H + + h E e l + h G n o n e l + h E n u c ] 1.3643
The values of  G a q H +  = −270.3 kcal·mol−1 h E n u c  = −9.4 kcal·mol−1, and  h G n o n e l  = 0 kcal·mol−1 are reported in the literature [17]. Values of  h E e l  were determined by optimization of the molecular structures. In addition, the SHE method used the implicit–explicit model, which added one additional water molecule to the amine. In addition, an empirical correction factor was included to minimize the errors between the estimated experimental values as in Equation (13). The values of C were −1.7 for cyclic amines and −0.7 for acyclic amines [17].
p K a = [ 270.3 + E e l B · H 2 O E e l B H + · H 2 O 9.4 ] 1.3643 + C
However, as in Equation (11), the dissociation constant values could be calculated since  G a q B  and  G a q B H +  could be found directly without further simplification as in the SHE method. This method is called the theoretical method in this study. All values of  G a q B G a q B H + E e l B · H 2 O , and  E e l B H + · H 2 O  were determined using Gaussian (09 Revision B.01 SMP). These molecular structures of the amines and amines–water were built using GaussView version 5.0.9. For the theoretical method, the structures were optimized using different methods (DFT/B3LYP and MP2) and the basis sets (6-31G(d) and 6-311G++(d,p)), while the SHE method used the DFT calculation method and 6-31G(d) basis set. All the amines’ geometrical structures were optimized with water as a solvent and the polarizable continuum model (PCM).
In addition to the quantum computational chemistry calculation methods mentioned, COSMO-RS can be used to determine the dissociation constant values with the same concept as in Equation (11) at the standard temperature (T = 298.15 K). In this study, CosmothermX (Version C30_1201) software was used to estimate the pKa values for the studied amines with the TZVP calculation method. The results from these calculations were compared to the experimental values in Table 8. As mentioned above, the V1 superscript stands for the protonated main chain amino group while the V2 superscript stands for the branched or tertiary amino group.
By comparing the group functional methods in Table 7, the original PDS method tended to predict higher values than Sumon’s method, which led to higher values than Qian’s method. In general, the estimated values by Qian’s method were closest to the experimental values than the other methods, on average. It should be mentioned that Qian’s method had more functional groups than the original PDS and Sumon’s method. In addition, Qian’s method included the effects of the group functional group on the ε (theta) position while the original PDS and Sumon’s methods included only the δ (delta) position. Therefore, the estimated values by Qian’s method were the closest to the experimental values.
In addition, when comparing the values between the group functional methods and chemistry computational methods in Table 7 and Table 8, the group functional methods were found to be more accurate than the computational methods. The functional group methods were also much faster and cheaper than the computational methods as they did not require high-performance computers and complex software while providing reasonable results. In addition, the estimates obtained using the Cosmo-RS calculation using CosmothermX (version C30_1201) were much better than both the SHE and the classical methods.
As mentioned earlier, 3-(Diethylamino) propylamine’s first pKa can be associated with the tertiary amino position or V2 conformation in Figure 3. By comparing the estimated values by group functional methods and chemistry computational method (except the Cosmo-RS method), the pKa values for the tertiary protonated scenario were closer to the experimental value than the first protonated scenario. On the contrary, the group functional methods estimated the same values for 1,3-Diaminopentane for both cases. The computational methods with different basis sets have different values for dissociation constants for the different amine geometries. In particular, the SHE method and Cosmo-RS calculation provided the closest values to the experimental values while the classical methods estimated the best values, although all the values did not perfectly match the experimental results. According to the structure presented in Table 1, the chain is considered the longest structure while the branch is attached to the chain. Logically, one primary amino belongs to the chain while the other is the branch. By the group contributions, the effect of the primary on the chain and branch is the same for each group. Although the ethyl group effect on the pKa values was not studied, it will shift the original values. As observed in Table S7, the methyl group will reduce the original values; similarly, the ethyl group would have similar behavior with different values. By combining the logical analysis with the results reported in Table 6, the primary amino group attached to the chain would probably be protonated before the branched amino group.

7. Estimation of the Dissociation Constants at Various Temperatures by Computational Chemistry

The above methods were used to predict the pKa values for the amines at the standard temperature (T = 298.15 K). However, it was necessary to estimate the constants at different temperatures. Therefore, to determine the pKa values at various temperatures, a thermodynamic cycle would be employed. In this study, two different cycles would be used to calculate the constant values. Figure 4 represents a thermodynamic cycle which is called the “hydronium cycle”. Equation (14) was derived from Equation (11), as reported in the literature [20], where  G s * ( B H + ) G s * ( H 2 O ) G s * B ,  and  G s * ( H 3 O + )  are the free solvation energies of BH+, H2O, B, and H3O+, respectively. The gas phase acidity of BH+ is represented by  G g a s *  and is defined by Equation (15) [20], while  G g a s 0 B G g a s 0 H 3 O + G g a s 0 H 2 O ,  and  G g a s 0 B H +  are the Gibbs free energies for B, H3O+, H2O, and BH+ in the gas phase. In addition,  G 0 *  is the free energy change which is associated with moving from the standard state that uses a concentration of 1 atm in the gas phase and 1 mol·L−1 in the aqueous phase to a standard state that uses a concentration of 1·mol·L−1 in both the gaseous and aqueous phases. Equation (16) defines the values of  G 0 *  for different temperatures [20].
p K a = [ G g a s 0 + G s * B G s * B H + + G s * H 3 O + G s * H 2 O + G 0 * ] R T l n ( 10 )
G g a s 0 = G g a s 0 B + G g a s 0 H 3 O + G g a s 0 B H + G g a s 0 H 2 O
G 0 * = R T l n 24.46
The Gibbs free energy of the amines in the gaseous phase at various temperatures can be calculated by computational chemistry calculation. The solvation energies at various temperatures can be determined by Equation (17), as in the literature [20]. In the equation, CavE298 and  G s 298  are the cavitation energy and free energy of solvation at 298 K, respectively, which can be calculated by computational chemistry. The computational chemistry calculations can be used to determine the solvation-free energy of water (H2O) and hydronium (H3O+) at standard temperature (298.15 K). The values of −4.64, −5.05, and −5.12 kcal·mol−1 of water for three calculations (DFT/B3LYP/6-31G(d), DFT/B3LYP/6-311++G(d,p), and MP2/6-31G(d), respectively) at 298.15 K are very different from the experimental value of −6.32 kcal·mol−1 reported in the literature [21]. Similarly, the values of −77.63, −77.42, and −78.45 kcal·mol−1 of hydronium (H3O+) for three calculations (DFT/B3LYP/6-31G(d), DFT/B3LYP/6-311++G(d,p), and MP2/6-31G(d), respectively) at 298.15 K are much lower than the experimental values of −110.3 kcal·mol−1 found in the literature [21]. Therefore, this study employed the experimental values of −6.32 kcal·mol−1 and −110.3 kcal·mol−1 at 298.15 K to improve the accuracy. Similar to the previous calculations, the computational chemistry calculations were performed by the methods and basis sets as DFT/B3LYP/6-31G(d), DFT/B3LYP/6-311++G(d,p), and MP2/6-31G(d), while the solvation model was the polarizable continuum model (PCM) with water as the solvent. The results of the calculations are summarized in Table 9.
G s T = G s 298 + T 298 C a v E 298 298
By comparing the calculation values in Table 9 and the experimental values in Table S4, at the various temperatures, the calculation values obtained were very far from the experimental values. The differences could be the result of the errors between calculations and experimental values for each calculation or species in the cycle. For example, the significant differences for solvation-free energy of water and H3O+ between computational chemistry calculations and experimental values were observed previously. Therefore, more species or components involved in the thermodynamic cycle will result in more errors. By comparison, 3-(Diethylamino) propylamine with the protonated tertiary amino had constant values which were closer to the experimental values. Similarly, 1,3-Diaminopentane with the protonated chain primary amino had constant values close to the experimental results. Therefore, the calculations confirm the reaction order or mechanism of the two diamines as discussed previously. Furthermore, to reduce the components in the cycle in Figure 4, the hydronium H3O+ was replaced by the proton (H+) while the water molecule was completely removed, as in the protonated thermodynamic cycle in Figure 5.
Because the proton does not include any electron, it could not be used in computational chemistry calculation optimization. The gas phase free energies of protons at various temperatures were obtained by fitting the data in the literature [22] from 0 K to 400 K. The values are reported in Table S8 in the SI section. In addition, Equations (18) and (19) were applied for the new thermodynamic cycle. In the equations,  G s * B G s * B H + , and  G s * H +  were the free solvation energies of B, BH+, and H+, while  G g a s 0 B G g a s 0 H + , and  G g a s 0 B H +  were Gibbs free energies of B, H+, and BH+ in the gas phase. The calculations were performed the same as previously, while the cavitation energy of the proton was calculated with DTF/B3LYP/6-311G(d,p). The calculation results are summarized in Table 10.
p K a = [ G g a s 0 + G s * B G s * B H + + G s * H + + G 0 * ] R T l n ( 10 )
G g a s 0 = G g a s 0 B + G g a s 0 H + G g a s 0 B H +
By comparing the calculation results in Table 9 and Table 10 and the experimental measurements in Table S4 for the first dissociation constants (pKa), although the calculation results which were based on the protonated thermodynamic cycle were not very close to the experimental measurements, the protonated thermodynamic cycle calculations were much better than the hydronium thermodynamic cycle calculation results. The improvements could be the result of using the experimental data of the proton, rather than using all the calculation results of the proton. In addition, the basis set of 6-311G++(d,p) underestimated the calculation results while the basis set of 6-31G(d) overestimated the results. In addition, 3-(Diethylamino) propylamine with the protonated tertiary amino (V2) had constant values closer to the experimental values than the protonated primary amino version (V1), on average. For 1,3-Diaminopentane, the protonated chain primary amino 1,3-Diaminopentane (V1) had dissociation constant values closer to the experimental results than the protonated branch primary amino 1,3-Diaminopentane (V2) on average. The calculations confirm the reaction order or mechanism of the two diamines which have been discussed previously.

8. The Artificial Neural Network (ANN) Models for Estimating the Constant Values of the Studied Amines

8.1. ANN Model with Input Parameters

As observed in the results and previous discussions, the dissociation constants of the studied amines at various temperatures were quite far from the experimental measurements. Although the measurements provided the most accurate values, the purchase of the chemicals is expensive in addition to the cost of waste disposal. In addition, chemists and chemical engineers have a great interest in estimating the constant values of chemicals even before their synthesis. Therefore, many researchers have attempted estimating the constant values at various temperatures with higher accuracies.
For computational chemistry estimation, Khalili et al. [12] used the commercial software Gaussian to predict the dissociation constant values of 17 amines at 298.15 K with ±0.68 pKa unit accuracy. Based on the Khalili–Henni–East (KHE) method [12], Sumon et al. [20] performed the calculations and improved the estimations to within ±0.28 pKa unit accuracy at the standard temperature. Although computational chemistry calculations can be applied to estimate the pKa for chemicals with known structures, the method could consume much CPU time and memory for large molecules. In addition to quantum chemistry calculations and quantitative structure–property relationship (QSPR) methods, artificial neural networks (ANNs) can be used to substitute experimental measurements. In summary, an ANN is a mathematical model which imitates the human brain to analyze information [23]. One of the advantages of an ANN is its flexibility to be applied in many fields using the nonlinear relationship in complicated systems without deep knowledge of the model; therefore, ANN applications have become very popular in solving engineering as well as scientific problems [24,25]. Habibi-Yangjeh et al. [25] predicted the dissociation constants of many different benzoic acids and phenol at standard temperature (298.15 K) by combining QSPR and ANN. The squared correlation coefficients (R2) of the ANN model for training, validation, and prediction were 0.9926, 0.9943, and 0.9939, respectively. Many scientists have combined two models (ANN and QSPR) to estimate the constant values of chemicals. One of the challenges was to convert chemical structures to numerical information to feed into the ANN model. Another challenge was that these works were performed at the standard temperature (298.15 K). In this study, the ANN model is used for predicting pKa values for the amines at various temperatures.
First of all, data were collected to feed into the model (input data) and references (output) were obtained. The data can generally be divided into three segments, which included (1) properties that identified the chemicals (molecular weight, temperature, number of H, N, C, and O atoms), (2) properties associated with the dissociation constants (density, viscosity, refractive index, and sound velocity), and (3) referenced output (experimental measurement pKa values). In this study, 1140 data points of 31 sets of amines associated with CO2 capture were collected and are listed in Table S9 in the SI section.
In the ANN study, the data were divided into three groups for training, validation, and testing. For training purposes, of the entire dataset, 70% of the data was randomly chosen. Similarly, of the entire dataset, 15% was randomly chosen for validation while the remaining 15% of the dataset was selected for testing the ANN model. In addition, this study optimized the number of hidden layers, the number of neurons in each hidden layer, and the number of epochs with the optimal condition of minimizing the mean squared error (MSE) in the ANN model. Initially, only one hidden layer was applied while the number of neurons varied from 30 to 80. Figure S2 shows the performances which included the correlation® and mean squared error (MSE) of the ANN model.
Based on Figure S2, the ANN model performed well with one hidden layer when the number of neurons was equal to 40. In particular, the Roverall = 0.86156, MSEtrain = 0.0288, MSEvalidation = 0.0460, and MSEtest = 0.09044. To study the effect of additional hidden layers, an extra hidden layer was added with 40 neurons for the first layer, while the number of neurons for the extra hidden layer was varied from 10 to 50. Figure S3 shows the performances with R and MSE of the ANN model. As observed in Figure S3, the performances of the ANN model significantly improved by introducing the second hidden layer into the model. In particular, the model was optimized when the number of neurons was 39 with Roverall = 0.9075, MSEtrain = 0.0069, MSEvalidation = 0.0372, and MSEtest = 0.0597.
For further improvement, an additional third hidden layer was introduced into the ANN model. However, the performances of the ANN model did not improve; therefore, as a final scenario, this study used 40 and 39 neurons for the first and second hidden layers, respectively. The neurons, weights, and biases for the first, second, and output layers are reported in Table 11, Table 12 and Table 13, respectively. The overfitting in the ANN model happened when the model could predict the output with very high accuracy in the training process; however, the predictions would not fit well in the validating and testing processes. Therefore, balancing the accuracies between all processes is necessary to avoid overfitting issues. In addition, the studied ANN model chose the right balance between the variables and the hyperparameters which were the number of epochs, neurons, and batch sizes.
The ANN model architecture was described in Figure S4 for this study. The process of determining the best overall performance by running the model with many epochs varying from 140 to 200 is presented in Figure S5. Based on the results, the best performance for the overall MSE was at 166 epochs with a value of 0.026.
Figure S6 is a parity plot between the output and target for the entire dataset which included training, validation, and testing. The overall R was higher than 0.9; therefore, the ANN model provided a good estimation of the dissociation constants for a wide range of temperatures. Figure S7 shows the error histogram with only a few outliers. Based on the figure, the majority of the errors were close to the value of −0.06303, which almost overlaps with the zero line.

8.2. ANN Model with Optimized Input Parameters

Previously, the ANN model with the provided inputs resulted in high-accuracy prediction; however, the model required many of experimental data. In an effort to make the ANN model more robust and faster, a further study was performed on reducing the number of inputs to decrease the number of experimental input data as well as speed up the training processes. In the model, the temperatures were unchanged because they directly have impact on the pKa values. This study focuses on the omission of some inputs to obtain an acceptable trade-off between the errors, complexities, and training speed.
From the previous full model, the study reduces the number of inputs such as density, refractive index, and the number of atoms (molecular weights) or combinations and examines the Roverall, MSEtrain, MSEvalidation, and MSEtest. The results are summarized in Table 14 below. The Roverall reached the highest values of 0.89225, while MSEtrain, MSEvalidation, and MSEtest were 0.00881, 0.02945, and 0.0798, respectively, when the sound velocity and refractive index were omitted. By comparison with the full model, the value of Roverall of the full model was a little higher than the Roverall of the reduced model, while the values of MSEtrain, MSEvalidation, and MSEtest of the full model were lower than the values of the reduced model. However, the differences were not large, and the reduced model did not require two sets of experimental datasets, which were the speed of sound and refractive index. Other combinations and the results are shown in Table 14.
Table 15, Table 16 and Table 17 summarize the weights and biases for the first, second hidden, and output layers of the reduced (refractive index and sound velocity) model.
Figure S8 shows the performance of the reduced ANN model with several epochs ranging from 140 to 200. The figure shows that the best output of the model was when the number of epochs reached 187.
Figure S9 shows the parity plot between the estimated and the experimental (target) values. The overall R was over 0.89, while Figure S10 represents the error histogram with very few outliers. Based on Figure S10, most of the errors were close to the value of 0.0136 while most of the errors were in the range of −0.0785 to 0.1057.

8.3. The Simulated ANN Model with Simulated Inputs

As observed in the previous sections, the ANN inputs included many other experimental measurements, such as densities, viscosities, and so on. It would consume more time to obtain all the measured data than directly measuring the pKa. In addition, it is impossible to obtain all of the data to estimate the dissociation constants values at various temperatures if the chemicals are synthesized. Therefore, it would be more convenient to develop an ANN model that can estimate the dissociation constant values based on the simulated data. Therefore, the model is called the simulated ANN model in this study. In this section, the chemicals are used to obtain the ANN model, the same as in the previous ANN models. In addition to the temperatures (K), the molecular weight (MW), and the output values (pKa) taken from the literature, the simulated data which include critical pressure (Pc/kPa), critical temperature (Tc/K), acentric factor (ω), the boiling temperature at 1 atm (Tb/K), flash point temperature (TF/K), density (ρ/g⸳cm−1), dynamic viscosity (η/cP), and vapor pressure (Pv/mbar), were used for the ANN model. In particular, critical pressures, critical temperatures, acentric factors, and boiling temperatures were obtained by the NIST estimation system from Aspen Plus V11.0, while flash point temperatures, densities, dynamic viscosities, and vapor pressures were calculated by CosmothermX (version C30_1201). In summary, the input of the ANN model includes 10 different types of data while the outputs are the same as the previous records. Because of the same number of inputs and outputs, the numbers of neurons for the two hidden layers are kept the same. The ANN structure for the model is the same as in Figure S4. After training, the obtained parameters were Roveral = 0.9988, MSEoveral = 0.0012, MSEtrain = 0.0016, MSEvalidation = 4.8433 × 10−5, and MSEtest = 1.1246 × 10−4. The weights and biases for the first, second hidden, and output layers are reported in Table 18, Table 19 and Table 20. The simulated ANN model performance with various epochs is shown in Figure S11. Figure S12 shows the parity plot between the estimated and the experimental values, while Figure S13 represents the error histogram of the simulated ANN model.
Based on the overall correlation coefficient and mean squared errors of the ANN model, as mentioned above, the model can provide a good estimation of the dissociation constants at various temperatures. When comparing the full, reduced, and simulated ANN models with the same ANN architecture, the overall correlation coefficients (Roveral), and mean squared errors (MSEs) for overall, training, validating, and testing of the three models were not very different. The simulated model has even lower mean squared errors with higher overall correlation coefficients than the other models. In addition, the simulated model is more convenient than the others because it uses the simulated data for the estimations.

9. Conclusions

The first and second pKa of 3-(Diethylamino) propylamine, 1,3-Diaminopentane, 3-Butoxypropylamine, 2-(Methylamino) ethanol, Bis(2-methoxyethyl) amine, α-Methylbenzyl-amine, 2-Aminoheptane, and 3-Amino-1-phenylbutane were experimentally measured from the temperature range between 293.15 K to 313.15 K with 5 K increments and 323.15 K at atmospheric pressure. The dissociation constants of the amines decreased when the temperature increased. In addition, by employing the Van’t Hoff equation, the thermodynamic quantities of the reactions were determined for the eight amines studied. Among the amines, 3-(Diethylamino) propylamine and 1,3-Diaminopentane have unsymmetrical structures; it is, therefore, necessary to determine the protonation reaction orders for these amines. Computational chemistry calculations confirmed that the first pKa values of 3-(Diethylamino) propylamine were associated with the tertiary amino while the first pKa values of 1,3-Diaminopentane were associated with the primary amino group on the carbon chain.
In addition, the dissociation constant values of the studied amines at 298.15 K were calculated using functional group and computational chemistry methods. The paper–pencil methods provided faster calculations while keeping the predicted pKa values at acceptable accuracy. As the paper–pencil methods could not determine the dissociation constants at any temperature but at 298 K, computational chemistry methods were used to perform the calculations using two different thermodynamic cycles. The two cycles resulted in different predictions. However, the calculated values were not very accurate; therefore, artificial neural network (ANN) models were tested to provide better accuracy. The models simply collected and combined experimental data of many amines to estimate the pKa. Although the ANN models can produce very good estimations, the main drawback was to obtain the experimental data. If the required data were not available or the chemicals had not been synthesized, the dissociation constant values could not be determined. Instead of using the experimental properties, the software can be used to generate the data for the ANN model. The simulated ANN model was able to fit the experimental pKa quite well.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/liquids3020016/s1. References [26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64] are cited in the supplementary materials.

Author Contributions

Conceptualization, A.H. and W.N.; methodology, V.S.P.V.A. and W.N.; software, W.N. and V.S.P.V.A.; validation, V.S.P.V.A. and W.N.; formal analysis, V.S.P.V.A. and W.N.; investigation, V.S.P.V.A. and W.N.; resources, A.H.; data curation, V.S.P.V.A. and W.N.; writing—original draft preparation, V.S.P.V.A. and W.N.; writing—review and editing, A.H.; visualization, W.N.; supervision, A.H.; project administration, A.H. and W.N.; funding acquisition, A.H. All authors have read and agreed to the published version of the manuscript.

Funding

This work was funded by the Natural Science and Engineering Council (NSERC), Canada, in the form of a Discovery Grant.

Data Availability Statement

Data used in this manuscript can be found in the Supplementary Materials Section.

Acknowledgments

The authors wish to express their appreciation to the Natural Sciences and Engineering Research Council (Canada) for providing a Discovery Grant to the corresponding author, and an NSERC PGS D scholarship to the first author.

Conflicts of Interest

The authors declare no competing financial interests.

References

  1. Ang, B.; Su, B. Carbon emission intensity in electricity production: A global analysis. Energy Policy 2016, 94, 56–63. [Google Scholar] [CrossRef]
  2. Chakma, A.; Mehrotra, A.; Nielsen, B. Comparison of Chemical Solvents for Mitigating CO2 Emissions from Coal-Fired Power Plants. Heat Recovery Syst. CHP 1995, 15, 231–240. [Google Scholar] [CrossRef]
  3. Kim, I.; Jens, C.; Grimstvedt, A.; Svendsen, H. Thermodynamics of Protonation of Amines in Aqueous Solutions at Elevated Temperatures. J. Chem. Thermodyn. 2011, 43, 1754–1762. [Google Scholar] [CrossRef]
  4. Chowdhury, F.; Yamada, H.; Higashii, T.; Goto, K.; Onoda, M. CO2 Capture by Tertiary Amine Absorbents: A Performance Comparison Study. Ind. Eng. Chem. Res. 2013, 52, 8323–8331. [Google Scholar] [CrossRef]
  5. Tomizaki, K.; Shimizu, S.; Onoda, M.; Fujioka, Y. An Acid Dissociation Constant (pKa)-Based Screening of Chemical Absorbents That Preferably Capture and Release Pressurized Carbon Dioxide for Greenhouse Gas Control. Chem. Lett. 2008, 37, 516–517. [Google Scholar] [CrossRef]
  6. Perrin, D. Dissociation Constants of Inorganic Acids and Bases in Aqueous Solution; Australian National University: Canberra, Australia, 1969. [Google Scholar]
  7. Versteeg, G.; Van Dijck, L.; Van Swaaij, W. On The Kinetics Between CO2 and Alkanolamines both In Aqueous and Non-Aqueous Solutions. An Overview. Chem. Eng. Commun. 1996, 144, 113–158. [Google Scholar] [CrossRef]
  8. Sharma, M. Kinetics of Reactions of Carbonyl Sulphide and Carbon Dioxide with Amines and Catalysis by Bronsted Bases of The Hydrolysis of COS. Trans. Faraday Soc. 1965, 61, 681–688. [Google Scholar] [CrossRef]
  9. Kumar, A.; Solanki, A.; Nguyen, W.H.C.H.; Henni, A. Determination and Prediction of Dissociation Constants and Related Thermodynamic Properties for 2-(Butylamino)ethanol, m-Xylylenediamine, 3-Picolylamine, Isopentylamine, and 4-(Aminoethyl)-piperidine. J. Chem. Eng. Data 2020, 65, 5437–5442. [Google Scholar] [CrossRef]
  10. Nguyen, W.H.C.H.; Henni, A. Dissociation Constant (pKa) and Thermodynamic Properties of 1,4-Bis(3-aminipropyl) Piperazine, 1,3-Bis(aminomethyl) Cyclohexane, Tris(2-aminoethyl) Amine, and 1-Amino-4-methyl Piperazine: Study of the Protonation Mechanism Using the Density Function Theory. J. Chem. Eng. Data 2020, 65, 2280–2290. [Google Scholar] [CrossRef]
  11. Hamborg, E.; Niederer, J.; Versteeg, G. Dissociation Constants and Thermodynamic Properties of Amino Acids Used in CO2 Absorption From (293 To 353) K. J. Chem. Eng. Data 2007, 52, 2491–2502. [Google Scholar] [CrossRef]
  12. Khalili, F.; Henni, A.; East, A. pKa Values of Some Piperazines at (298, 303, 313, and 323) K. J. Chem. Eng. Data 2009, 54, 2914–2917. [Google Scholar] [CrossRef]
  13. Albert, A.; Serjeant, E.P. The Determination of Ionization Constants. In A Laboratory Manual, 3rd ed.; Chapman and Hall: New York, NY, USA, 1984. [Google Scholar]
  14. Rayer, A.; Sumon, K.; Jaffari, L.; Henni, A. Dissociation Constants (pKa) of Tertiary and Cyclic Amines: Structural and Temperature Dependences. J. Chem. Eng. Data 2014, 59, 3805–3813. [Google Scholar] [CrossRef]
  15. Tagiuri, A.; Mohamedali, M.; Henni, A. Dissociation Constant (pKa) And Thermodynamic Properties of Some Tertiary and Cyclic Amines From (298 to 33) K. J. Chem. Eng. Data 2016, 61, 247–254. [Google Scholar] [CrossRef]
  16. Perrin, D.; Dempsey, B.; Serjeant, E. pKa Prediction for Organic Acids and Bases; Springer: Berlin/Heidelberg, Germany, 1981. [Google Scholar]
  17. Sumon, K.; Henni, A.; East, A. Predicting pKa of Amines for CO2 Capture: Computer Versus Pencil-And-Paper. Ind. Eng. Chem. Res. 2012, 51, 11924–11930. [Google Scholar] [CrossRef]
  18. Qian, J.; Sun, R.; Sun, S.; Gao, J. Computer–Free Group–Addition Method for pKa Prediction of 73 Amines for CO2 Capture. J. Chem. Eng. Data 2016, 62, 111–122. [Google Scholar] [CrossRef]
  19. Khalili, F.; Henni, A.; East, A.L.L. Entropy Contributions In pKa Computation: Application to Alkanolamines and Piperazines. J. Mol. Struct. THEOCHEM 2009, 916, 1–9. [Google Scholar] [CrossRef]
  20. Gupta, M.; da Silva, E.F.; Svendsen, H.F. Modeling Temperature Dependency of Amine Basicity Using PCM and SM8T Implicit Solvation Models. J. Phys. Chem. B 2012, 116, 1865–1875. [Google Scholar] [CrossRef]
  21. Along, K.S.; Shields, G.C. Theoretical Calculations of Acid Dissociation Constants: A Review Article. Annu. Rep. Comput. Chem. 2010, 6, 113–138. [Google Scholar]
  22. Fifen, J.J.; Dhaouadi, Z.; Nsangou, M. Revision of the Thermodynamics of the Proton in Gas Phase. J. Phys. Chem. A 2014, 118, 11090–11097. [Google Scholar] [CrossRef]
  23. Yegnanaryana, B. Artificial Neural Networks; PHI Learning Pvt. Ltd.: New Delhi, India, 2009. [Google Scholar]
  24. Artemenko, N.V.; Baskin., I.I.; Palyulin, V.A.; Zefirov, N.S. Prediction of Physical Properties of Organic Compounds Using Artificial Neural Networks within the Substructure Approach. Chemistry 2001, 381, 317–320. [Google Scholar] [CrossRef]
  25. Habibi-Yangjeh, A.; Damandeh-Jenagharad, M.; Nooshyar, M. Prediction Acidity Constant of Various Benzoic Acids and Phenols in Water Using Linear and Nonlinear QSPR models. Bull. Korean Chem. Soc. 2005, 26, 2007. [Google Scholar] [CrossRef]
  26. Mandal, B.P.; Kundu, M.; Bandyopadhyay, S.S. Density and viscosity of aqueous solutions of (N-methyldiethanolamine + monoethanolamine), (N-methyldiethanolamine + diethanolamine), (2-amino-2-methyl-1-propanol + monoethanolamine), and (2-amino-2-methyl-1-propanol + diethanolamine). J. Chem. Eng. Data 2003, 48, 703–707. [Google Scholar] [CrossRef]
  27. Muhammad, A.; Mutalib, M.I.A.; Murugesan, T.; Shafeeq, A. Density of Excess Properties of Aqueous N-methyldiethanolamine Solutions from (298.15 to 338.15) K. J. Chem. Eng. Data 2008, 53, 2217–2221. [Google Scholar] [CrossRef]
  28. Blanco, A.; Garc, A.; Gomez-Diaz, D.; Navaza, J.M.; Villaverde, O.L. Density, Speed of Sound, Viscosity, Surface Tension, and Excess Volume of N-Ethyl-2-Pyrolidone+Ethanolamine (or Diethanolamine or Triethanolamine) from T = (293.15 to 323.15) K. J. Chem. Eng. Data. 2013, 58, 653–659. [Google Scholar] [CrossRef]
  29. Blanco, A.; Garc, A.; Gomez-Diaz, D.; Navaza, J.M. Density, Speed of Sound, Viscosity, Refractive Index, and Excess Volume of N-Methyl-1-Pyrorolidone + Ethanol (or Water or Ethanolamine) from T = (293.15 to 323.15) K. J. Chem. Eng. Data 2017, 56, 646–651. [Google Scholar] [CrossRef]
  30. Moosavi, M.; Sisco, C.J.; Rostami, A.A.; Vargas, F.M. Thermodynamic Properties and CO2 Solubility of Monoethanolamine + Diethylenetriamine/Aminoethylethanolamine Mixtures: Experimental Measurements and Thermodynamic Modeling. Fluid Phase Equilibria 2017, 449, 175–185. [Google Scholar] [CrossRef]
  31. Vazquez, G.; Alvarez, E.; Navaza, J.M.; Rendo, R.; Remero, E. Surface Tension of Binary Mixtures of Water + Monoethanolamine and Water + 2-Amino-2-Methyl-1-Propanol and Tertiary Mixtures of these Amines with Water from 25 °C to 50 °C. J. Chem. Eng. Data 1997, 42, 57–59. [Google Scholar] [CrossRef]
  32. Rayer, A.V.; Kadiwala, S.; Narayanaswamy, K.; Henni, A. Volumetric Properties, Viscosities, and Refractive Indices for Aqueous 1-Amino-2-Propanol (monoisopropanolamine (MIPA)) Solutions from (298.15 to 343.15) K. J. Chem. Eng. Data 2010, 55, 5562–5568. [Google Scholar] [CrossRef]
  33. Narayanaswamy, K.; Rayer, A.V.; Kadiwala, S.; Henni, A. Volumetric Properties, Viscosities, Refractive Indices and Surface Tensions for (Dimethyl Propanol Amine (DMPA) + Water) Mixtures from 298.15 K to 343.15 K. Thermochim Acta 2012, 543, 218–225. [Google Scholar] [CrossRef]
  34. Li, J.; Mundhwa, M.; Tontiwachwuthikul, P.; Henni, A. Volumetric Properties, Viscosities, and Refractive Indices for Aqueous 2-(Methylamino)Ethanol Solutions from (298.15 to 343.15) K. J. Chem. Eng. Data 2007, 52, 560–565. [Google Scholar] [CrossRef]
  35. Hamborg, E.S.; Verteeg, G.F. Dissociation Constants and Thermodynamic Properties of Alkanolamines. Energy Proced. 2009, 1, 1213–1218. [Google Scholar] [CrossRef]
  36. Ghulam, M.; Mohd, S.A.; Azmi, B.M.; Faizan, A. Volumetric Properties, Viscosities and Refractive Indices of Aqueous Solutions of 2-Amino-2-Methyl-1-Propanol (AMP). Res. J. Chem. Environ. 2013, 17, 22–31. [Google Scholar]
  37. Alvarz, E.; Cerdeira, F.; Gomez-Diaz, D.; Navaza, J.M. Density, Speed of Sound, Isentropic Compressbility, and Excess Volume of Bianary Mixtures of 1-Amino-2-Propanol or 3-Amino-1-Propanol with 2-Amino-2-Methyl-1-Propanol, Diethanolamine, or Triethanolamine from (293.15 to 323.15) K. J. Chem. Eng. Data 2008, 55, 2567–2575. [Google Scholar] [CrossRef]
  38. Spasojević, V.D.; Šerbanović, S.P.; Djordjević, B.D.; Kijevčanin, M.L. Densities, Viscosities, and Refractive Indices of Aqueous Alkanolamine Solutions as Potential Carbon Dioxide Removal Reagents. J. Chem. Eng. Data 2012, 58, 84–92. [Google Scholar] [CrossRef]
  39. Tseng, Y.M.; Thompson, A.R. Densities and Refractive Indices of Aqueous Monoethanolamine, Diethanolamine, Triethanolamine. J. Chem. Eng. Data 1964, 9, 264–267. [Google Scholar] [CrossRef]
  40. Vázquez, G.; Alvarez, E.; Rendo, R.; Romero, E.; Navaza, J.M. Surface Tension of Aqueous Solutions of Diethanolamine and Triethanolamine from 25 °C to 50 °C. J. Chem. Eng. Data 1996, 41, 806–808. [Google Scholar] [CrossRef]
  41. Bower, V.E.; Robinson, R.A.; Bates, R.G. Acidic Dissociation Constant and Related Thermodynamic Quantities for Diethanolammonium Ion in Water from 0 to 50 °C. J. Res. Natl. Bur. Stand. A 1962, 66, 71–75. [Google Scholar] [CrossRef]
  42. Tennyson, R.; Schaaf, R. Guidelines Can Help Choose Proper Process for Gas-Treating Plants. Oil Gas J. 1977, 75, 78–80. [Google Scholar]
  43. Rochelle, G.T. Amine Scrubbing for CO2 Capture. Science 2009, 325, 1652–1654. [Google Scholar] [CrossRef]
  44. Aboaba, A.J. Reaction Kinetics and Dissociation Constants (pKa) of Tertiary Alkanolamines for Carbon Capture. Master’s Thesis, University of Regina, Regina, SK, Canada, 2017. [Google Scholar]
  45. Omrani, A.; Rostami, A.A.; Mokhtary, M. Densities and Volumetric Properties of 1,4-Dioxane with Ethanol, 3-Methyl-1-Butanol, 3-Amino-1-Propanol and 2-Propanol Binary Mixtures at Various Temperatures. J. Mol. Liq. 2010, 157, 18–24. [Google Scholar] [CrossRef]
  46. Álvarez, E.; Cancela, Á.; Maceiras, R.; Navaza, J.M.; Táboas, R. Surface Tension of Aqueous Binary Mixtures of 1-Amino-2-Propanol and 3-Amino-1-Propanol, and Aqueous Ternary Mixtures of these Amines with Diethanolamine, Triethanolamine, and 2-Amino-2-Methyl-1-Propanol from (298.15 to 323.15) K. J. Chem. Eng. Data 2003, 48, 32–35. [Google Scholar] [CrossRef]
  47. Saravanakumar, K.; Baskaran, R.; Kubendran, T.R. Thermophysical Properties of Acetophenone with N, N-Dimethylethanolamine or with N, N-Diethylethanolamine at Temperatures of (303.15, 313.15 and 323.15) K and Pressure of 0.1 MPa. J. Solut. Chem. 2011, 40, 955–967. [Google Scholar] [CrossRef]
  48. Iloukhani, H.; Rakhshi, M. Excess Molar Volumes, Viscosities, and Refractive Indices for Binary and Ternary Mixtures of {Cyclohexanone (1) + N,N-Dimethylacetamide (2)+N,N-Diethylethanolamine (3)} at (298.15, 308.15, and 318.15) K. J. Mol. Liq. 2009, 149, 86–95. [Google Scholar] [CrossRef]
  49. DiGuilio, R.M.; Lee, R.J.; Schaeffer, S.T.; Brasher, L.L.; Teja, A.S. Densities and Viscosities of the Ethanolamines. J. Chem. Eng. Data 1992, 37, 239–242. [Google Scholar] [CrossRef]
  50. Alvarz, E.; Gamez-Daz, D.; La Rubia, M.D.; Navaza, J.M. Surface Tensions of Aqueous Binary Mixtures of 2-(Methylamino)ethanol and 2-(Ethylamino)ethanol and Aqueous Ternary Mixtures of these Amines with Triethanolamine or N-Methyldiethanolamine from (293.15 to 323.15)K. J. Chem. Eng. Data 2007, 53, 318–321. [Google Scholar] [CrossRef]
  51. Alvarez, E.; Gamez-Daz, D.; La Rubia, M.D.; Navaza, J.M. Densities and Viscosities of Aqueous Ternary Mixtures of 2-(Methylamino)ethanol and 2-(Ethylamino)ethanol with Diethanolamine, Triethanolamine, N-Methyldiethanolamine, or 3-Amino-1-Methyl-1-Propanol from 298.15 to 323.15 K. J. Chem. Eng. Data 2006, 51, 955–962. [Google Scholar] [CrossRef]
  52. Lampreia, I.M.; Santos, Â.F.; Barbas, M.J.A.; Santos, F.J.; Matos Lopes, M.L. Changes in Aggregation Patterns Detected by Diffusion, Viscosity, and Surface Tension in Water + 2-(Diethylamino)Ethanol Mixtures at Different Temperatures. J. Chem. Eng. Data 2007, 52, 2388–2394. [Google Scholar] [CrossRef]
  53. Kinart, C.M.; Kinart, W.J.; Chęcińska-Majak, D.; Ćwiklińska, A. Refractive Properties of Binary Mixtures Containing 2-Methoxyethanol and N-Butylamine, Isobutylamine, sec-Butylamine and tert-Butylamine. Phys. Chem. Liq. 2003, 41, 383–389. [Google Scholar] [CrossRef]
  54. Wang, J.; Du, H.; Liu, H.; Yao, X.; Hu, Z.; Fan, B. Prediction of Surface Tension for Common Compounds Based on Novel Methods Using a Heuristic Method and Support Vector Machine. Talanta 2007, 73, 147–156. [Google Scholar] [CrossRef]
  55. Pal, A.; Kumar, A.; Kumar, H. Volumetric, Acoustic, Viscometric, and Spectroscopic Properties for Binary Mixtures of Alkoxypropanol with mono, di- and tri-Alkylamines at a Temperature of 298.15K. J. Chem. Thermodyn. 2006, 38, 1227–1239. [Google Scholar] [CrossRef]
  56. Ahmadloo, Z. Predictability of Carbon Dioxide and Ethane Solubility in Ionic Liquids: A Simulation Approach. Master’s Thesis, University of Regina, Regina, SK, Canada, 2016. [Google Scholar]
  57. Sumon, K.Z. Quantum-Mechanical and Thermodynamic Study of Amines and Ionic Liquids for CO2 Capture. Ph.D. Thesis, University of Regina, Regina, SK, Canada, 2013. [Google Scholar]
  58. Blanco, A.; García -Abuín, A.; Gómez -Díaz, D.; Navaza, J.M. Density, Speed of Sound, Viscosity and Surface Tension of 3-Dimethylamino-1-Propylamine+ Water, 3-Amino-1-Propanol + 3-Dimethylamino-1-Propanol, and (3-Amino-1-Propanol + 3-Dimethylamino-1-Propanol) + Water from T = (293.15 to 323.15) K. J. Chem. Eng. Data 2017, 62, 2272–2279. [Google Scholar] [CrossRef]
  59. Tissier, C.; Barillie, P. Acidity Constants and Thermodynamic Functions of Acids Conjugated with Some Propanediamines. Comptes Rendus Hebd. Séances L’Académie Des Sci. Série C 1969, 268, 1953. [Google Scholar]
  60. Liu, G.; Nguyen, W.H.; Henni, A. Experimental determination of dissociation constants (pKa) for N-(2-aminoethyl)-1,3-propanediamine, 2-methylpentamethylene diamine, N,N-dimethyldipropylenetriamine, 3,30-diamino-N-methyldipropyl-amine, Bis[2-(N,N-dimethylamino)ethyl]ether, 2-[2-(dimethyl-amino) ethoxy] ethanol, 2-(dibutylamino) ethanol, and N-propylethanol-amine and modeling with artificial neural network. AIChE J. 2022, 69, e17923. [Google Scholar] [CrossRef]
  61. Jamal, M.A.; Khosa, M.K.; Naseem, B.; Zaheer-Ud-Din, M.; Muneer, M. Excess Molar Volume and Isentropic Compressibility of Monoethanolamine in Aqueous System at Temperatures from 298.15 to 318.5 K. Phys. Chem. Liq. 2016, 54, 384–393. [Google Scholar] [CrossRef]
  62. Garcia-Abuin, A.; Gomez-Diaz, D.; Rubia, M.D.L.R.; Navaza, J.M. Desnity, Speed of Sound, Viscosity, Refractive Index, and Excess Volume of N-Methyl-2-pyrrolidone + Ethanol (or Water or Ethanolamine) from T = (293.15 to 323.15 K). J. Chem. Eng. Data 2011, 57, 1009–1014. [Google Scholar]
  63. Arachchige, U.S.P.R.; Aryal, N.; Eimer Dag, A.; Melaaen, M.C. Viscosities of Pure and Aqueous Solutions of Monoethanolamine (MEA), Diethanolamine (DEA) and N-Methyldiethanolamine (MDEA). Ann. Trans. Nordic Rheol. Soc. 2013, 21, 299. [Google Scholar]
  64. Nguyen, H.C.H.W.; Henni, A. Volumetric Properties, Speeds of Sound, Viscosities, and Refractive Indices of {1,4-Bis(3-aminopropyl)piperazine + Water} Binary Mixture from 293.15 to 343.15 K. J. Chem. Eng. Data 2022, 67, 1101–1114. [Google Scholar] [CrossRef]
Figure 1. Linear relationship between the first dissociation constants and inverse temperatures of the amines studied.
Figure 1. Linear relationship between the first dissociation constants and inverse temperatures of the amines studied.
Liquids 03 00016 g001
Figure 2. Linear relationship between the second dissociation constants with the inverse of temperature for diamines.
Figure 2. Linear relationship between the second dissociation constants with the inverse of temperature for diamines.
Liquids 03 00016 g002
Figure 3. The protonating possibilities for 3-(Diethylamino) propylamine and 1,3-Diaminopentane. Blue: nitrogen, grey: carbon, and white: hydrogen.
Figure 3. The protonating possibilities for 3-(Diethylamino) propylamine and 1,3-Diaminopentane. Blue: nitrogen, grey: carbon, and white: hydrogen.
Liquids 03 00016 g003
Figure 4. Hydronium thermodynamic cycle for calculating the dissociation constant.
Figure 4. Hydronium thermodynamic cycle for calculating the dissociation constant.
Liquids 03 00016 g004
Figure 5. Protonated thermodynamic cycle for calculating the dissociation constants.
Figure 5. Protonated thermodynamic cycle for calculating the dissociation constants.
Liquids 03 00016 g005
Table 1. Chemical name, structures, suppliers, and mass purity (%) of the studied amines.
Table 1. Chemical name, structures, suppliers, and mass purity (%) of the studied amines.
Full NameIUPAC NameAbbreviation NameCAS Reg. No.Molecular StructureMolecular Mass
(g⸳gmol−1)
SupplierMass Fraction Purity
(%)
Monoethanolamine2-AminoethanolMEA141-43-5Liquids 03 00016 i00161.08Sigma-Aldrich (Oakville, ON, Canada)≥99
3-(Diethylamino) propylamineN′,N′-diethylpropane-1,3-diamineDEAPA104-78-9Liquids 03 00016 i002130.23Sigma-Aldrich≥99
1,3-DiaminopentanePentane-1,3-diamineEP589-37-7Liquids 03 00016 i003102.18Sigma-Aldrich98
3-Butoxypropylamine3-Butoxypropan-1-amineBPA16499-88-0Liquids 03 00016 i004131.22Sigma-Aldrich99
2-(Methylamino) ethanol2-(Methylamino)ethanolMAE109-83-1Liquids 03 00016 i00575.11Sigma-Aldrich≥98
Bis(2-methoxyethyl) amine2-Methoxy-N-(2-methoxyethyl)ethanamineBMOA11-95-5Liquids 03 00016 i006133.19Sigma-Aldrich98
α-Methylbenzylamine1-PhenylethanaminePEA618-36-0Liquids 03 00016 i007121.18Sigma-Aldrich99
2-Aminoheptane[(2R)-heptan-2-yl]azaniumAH123-82-0Liquids 03 00016 i008115.22Sigma-Aldrich99
3-Amino-1-phenylbutane4-Phenylbutan-2-amineAPB22374-89-6Liquids 03 00016 i009149.24TCI (Portland, OR, USA)98
Table 2. The standard state enthalpy change (ΔH0/ kJ·mol−1) and entropy change (ΔS0/ kJ·mol−1·K−1) of the first dissociation constants of the studied amines.
Table 2. The standard state enthalpy change (ΔH0/ kJ·mol−1) and entropy change (ΔS0/ kJ·mol−1·K−1) of the first dissociation constants of the studied amines.
AmineΔH0 (kJ·mol−1)ΔS0 (kJ·mol−1·K−1)
3-(Diethylamino) propylamine46.05−0.05
1,3-Diaminopentane52.40−0.02
3-Butoxypropylamine52.83−0.01
2-(methylamino) ethanol44.27−0.04
Bis(2-methoxyethyl) amine39.21−0.03
α-Methylbenzylamine58.300.02
2-Aminoheptane130.90.24
3-Amino-1-phenylbutane65.680.03
Table 3. Standard state free energy of reaction (ΔG0, kJ·mol−1) of the first dissociation constants of the studied amines.
Table 3. Standard state free energy of reaction (ΔG0, kJ·mol−1) of the first dissociation constants of the studied amines.
AmineTemperature T/K
293.15298.15303.15308.15313.15323.15
3-(Diethylamino) propylamine59.3859.5959.7859.8860.1360.81
1,3-Diaminopentane59.2759.2559.3759.4159.4760.01
3-Butoxypropylamine56.3556.5156.5356.5856.5356.79
2-(Methylamino) ethanol55.6256.1756.3056.2856.3557.04
Bis(2-methoxyethyl) amine48.7749.2049.3949.3849.4649.93
α-Methylbenzylamine53.3253.4853.2252.7452.9453.02
2-Aminoheptane60.1160.1159.4358.9455.4053.51
3-Amino-1-phenylbutane58.4858.1657.9257.7657.6157.78
Table 4. The standard state enthalpy change (ΔH0/ kJ·mol−1) and entropy change (ΔS0/ kJ·mol−1·K−1) of the second dissociation constants of 3-(Diethylamino) propylamine and 1,3-Diaminopentane.
Table 4. The standard state enthalpy change (ΔH0/ kJ·mol−1) and entropy change (ΔS0/ kJ·mol−1·K−1) of the second dissociation constants of 3-(Diethylamino) propylamine and 1,3-Diaminopentane.
AmineΔH0 (kJ·mol−1)ΔS0 (kJ·mol−1·K−1)
3-(Diethylamino) propylamine55.330.03
1,3-Diaminopentane58.180.04
Table 5. Standard state free energy of reaction (ΔG0, kJ·mol−1) of the second dissociation constants of 3-(Diethylamino) propylamine and 1,3-Diaminopentane.
Table 5. Standard state free energy of reaction (ΔG0, kJ·mol−1) of the second dissociation constants of 3-(Diethylamino) propylamine and 1,3-Diaminopentane.
AmineTemperature T/K
293.15298.15303.15308.15313.15323.15
3-(Diethylamino) propylamine47.2647.0346.7846.6646.3446.52
1,3-Diaminopentane1.351.291.241.191.141.07
Table 6. The difference in potential energy surface (PES) between protonated 3-(Diethylamino) propylamine and 1,3-Diaminopentane structures.
Table 6. The difference in potential energy surface (PES) between protonated 3-(Diethylamino) propylamine and 1,3-Diaminopentane structures.
Model/Basis SetΔE (kJ·mol−1)
3-(Diethylamino) propylamine1,3-Diaminopentane
HF/6-311G+(d,p)64.91−7.13
DFT/B3LYP/3-21G5.72−17.71
DFT/B3LYP/6-311G+(d,p)14.93−6.13
MP2/6-311G+(d,p)21.00−8.65
Table 7. The estimated pKa values of the eight amines with three different methods at T = 298.15 K.
Table 7. The estimated pKa values of the eight amines with three different methods at T = 298.15 K.
SolventpKa, PDS [19]pKa, Sumon [20]pKa, QSSR [21]pKa [Exp.]
3-(Diethylamino) propylamineV110.6310.4410.2410.44
3-(Diethylamino) propylamineV210.3710.4610.28
1,3-DiaminopentaneV110.6410.4610.2810.38
1,3-DiaminopentaneV210.6410.4610.28
3-Butoxypropylamine10.5810.3810.139.90
2-(Methylamino) ethanol10.5110.5010.209.84
Bis(2-methoxyethyl) amine10.199.989.248.62
α-Methylbenzylamine10.7710.6010.609.37
2-Aminoheptane10.7710.6010.6010.53
3-Amino-1-phenylbutane10.7710.6010.6010.19
Table 8. Comparison between the estimated pKa values by different methods with experimental dissociation constants.
Table 8. Comparison between the estimated pKa values by different methods with experimental dissociation constants.
AmineSHE MethodTheoretical MethodCosmo-RS
Method
Experimental
Values
pKa without
Correction
pKa with
Correction
DFT/B3LYP
6-31G(d)
DFT/B3LYP
6-311G++(d,p)
MP2
6-31G(d)
3-(Diethylamino) propylamineV18.818.116.953.696.6010.3610.44
3-(Diethylamino) propylamineV210.279.578.746.818.239.89
1,3-DiaminopentaneV19.478.775.013.215.3810.6510.38
1,3-DiaminopentaneV28.427.727.994.117.169.39
3-Butoxypropylamine8.187.487.884.946.2410.029.90
2-(Methylamino) ethanol8.327.626.513.806.079.509.84
Bis(2-methoxyethyl) amine6.655.954.451.703.767.078.62
α-Methylbenzylamine7.696.495.202.134.749.299.37
2-Aminoheptane8.788.087.214.306.3110.4310.53
3-Amino-1-phenylbutane8.307.106.203.345.479.8310.19
The value in bold was used as an example.
Table 9. Dissociation constant values of the studied amines at various temperatures (K) for DFT1 (DFT/B3LYP/6-31G(d)), DFT2 (DFT/B3LYP/6-311G++(d,p)), and MP2 (MP2/6-31G(d)) calculations by hydronium thermodynamic cycle.
Table 9. Dissociation constant values of the studied amines at various temperatures (K) for DFT1 (DFT/B3LYP/6-31G(d)), DFT2 (DFT/B3LYP/6-311G++(d,p)), and MP2 (MP2/6-31G(d)) calculations by hydronium thermodynamic cycle.
AmineTemperature/K
293.15298.15303.15308.15313.15323.15
DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2
3-(Diethylamino) propylamineV17.347.437.877.247.327.777.147.237.667.057.137.566.967.047.476.796.877.28
3-(Diethylamino) propylamineV29.1610.619.539.0310.459.408.9110.319.278.7910.169.158.6810.029.038.469.768.80
1,3-DiaminopentaneV18.417.858.448.297.758.328.177.648.218.067.548.107.967.447.997.767.257.79
1,3-DiaminopentaneV25.346.946.625.306.946.635.266.776.465.236.696.385.196.616.305.126.456.16
3-Butoxypropylamine8.328.717.508.188.577.408.048.447.317.918.317.217.798.187.127.557.946.95
2-(Methylamino) ethanol6.907.547.336.817.437.246.727.337.146.637.247.056.557.156.966.406.976.79
Bis(2-methoxyethyl) amine4.795.404.984.745.344.934.695.284.884.655.224.834.605.174.784.515.064.69
α-Methylbenzylamine5.565.845.975.495.775.905.435.705.845.375.635.775.315.575.715.205.445.58
2-Aminoheptane7.608.047.587.507.937.487.417.837.387.327.737.297.237.647.207.067.457.02
3-Amino-1-phenylbutane6.587.076.726.496.986.636.416.886.556.336.806.476.266.716.396.116.556.24
Table 10. Dissociation constant values of the studied amines at various temperatures (K) for DFT1 (DFT/B3LYP/6-31G(d)), DFT2 (DFT/B3LYP/6-311G++(d,p)), and MP2 (MP2/6-31G(d)) calculations by protonated thermodynamic cycle.
Table 10. Dissociation constant values of the studied amines at various temperatures (K) for DFT1 (DFT/B3LYP/6-31G(d)), DFT2 (DFT/B3LYP/6-311G++(d,p)), and MP2 (MP2/6-31G(d)) calculations by protonated thermodynamic cycle.
AmineTemperature/K
293.15298.15303.15308.15313.15323.15
DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2DFT1DFT2MP2
3-(Diethylamino) propylamineV110.457.1310.0910.196.939.859.956.749.619.716.569.389.486.389.169.046.038.73
3-(Diethylamino) propylamineV212.2710.3111.7511.9910.0611.4811.729.8211.2211.459.5910.9611.209.3610.7210.718.9310.24
1,3-DiaminopentaneV111.517.5610.6611.247.3510.4010.987.1610.1510.736.969.9110.486.789.6810.016.429.24
1,3-DiaminopentaneV28.456.648.848.266.468.628.076.288.417.896.118.207.715.947.997.375.627.61
3-Butoxypropylamine11.428.429.7211.138.189.4810.857.959.2510.587.739.0310.317.528.819.817.118.40
2-(Methylamino) ethanol10.007.249.559.767.049.329.526.859.099.296.668.879.076.488.658.656.148.24
Bis(2-methoxyethyl) amine7.905.117.207.704.957.017.504.806.827.314.656.647.124.516.476.774.236.14
α-Methylbenzylamine8.675.548.198.455.387.988.245.217.788.035.067.587.834.907.397.464.617.03
2-Aminoheptane10.717.759.8010.467.549.5610.227.359.339.987.169.109.756.978.899.326.628.47
3-Amino-1-phenylbutane9.696.778.949.456.588.719.226.408.499.006.228.288.786.058.088.375.727.68
Table 11. Neurons, weights, and biases for the first hidden layer for the ANN model in this study.
Table 11. Neurons, weights, and biases for the first hidden layer for the ANN model in this study.
NeuronTemperatureMolecular WeightNumber of CNumber of HNumber of NNumber of ORefractive IndexSound VelocityDensityViscosityBias
1−0.16060.0418−0.21790.1791−0.53870.5581−0.01160.56010.39600.54080.1280
2−0.00190.2824−0.44850.6275−0.4088−0.09830.23420.2044−0.2735−0.95340.4230
30.35120.5736−0.4307−0.0813−0.7615−0.09660.65470.1445−0.7132−0.53330.3857
4−0.76570.40590.2351−0.13420.47310.5649−0.52870.4273−0.58890.45990.0970
5−0.56250.6416−0.0182−0.51740.36600.6449−0.1326−0.6361−0.25390.2892−0.1645
60.09530.3919−0.31180.39920.7698−0.6674−0.5810−0.1775−0.4318−0.74500.1681
70.20290.7125−0.57160.0432−0.38290.6687−0.41680.26580.21810.0705−0.1781
8−0.3264−0.72660.30550.0234−0.71610.0598−0.51980.09990.6816−0.47160.1862
9−0.69170.3358−0.2423−0.39210.55830.23050.3588−0.64940.4169−0.74510.1513
10−0.5985−0.8256−0.07130.6598−0.2951−0.1735−0.00840.62060.42610.3258−0.2165
110.77040.38030.46340.6663−0.48790.63560.48900.11100.2620−0.20920.0304
12−0.3404−0.5674−0.7932−0.5772−0.4899−0.2049−0.53430.2947−0.1619−0.12660.0807
13−0.0338−0.6166−0.3253−0.72510.06770.66140.4311−0.7018−0.6937−0.41530.1659
14−0.2682−0.50910.04800.3170−0.72250.8834−0.31580.0101−0.4100−0.12350.2524
150.2565−0.10780.3414−0.4316−0.21660.0072−0.79350.5236−0.0566−0.4636−0.0757
160.39580.4307−0.07010.2972−0.68330.58250.6117−0.5569−0.6424−0.50440.2795
170.03190.0469−0.35110.0314−0.96490.74940.49800.2465−0.73430.50670.2693
18−0.5768−0.27010.6151−0.52320.0859−0.7951−0.03210.04010.2094−0.07610.3236
19−0.1144−0.7453−0.02390.60690.8351−0.2969−0.00530.0238−0.16570.53110.1203
20−0.30660.4596−0.41900.0733−0.7205−0.9337−0.1272−0.2780−0.37810.28680.4707
21−0.7033−0.3322−0.75930.0392−0.30110.89930.5743−0.6363−0.5388−0.53410.1583
22−0.27570.5471−0.7170−0.3693−0.87870.6861−0.6731−0.68950.0206−0.17900.3536
230.0430−0.5891−0.5039−0.0625−0.5739−0.1442−0.36210.2378−0.2223−0.05270.3039
240.01800.8456−0.2889−0.63640.6036−0.0969−0.30550.2153−0.36600.13610.1386
250.40030.11140.5461−0.36750.6447−0.0693−0.71180.6243−0.07370.02060.3567
260.2454−0.43450.35520.4435−0.82930.3049−0.3266−0.6133−0.5094−0.0145−0.1643
27−0.36040.16350.44200.71400.89290.0178−0.2349−0.68500.20510.49700.1628
280.33330.05830.3531−0.1965−0.35990.5106−0.2346−0.72180.7650−0.31210.3366
29−0.4641−0.4724−0.59010.2899−0.0581−0.5267−0.3159−0.8717−0.0177−0.01390.1253
300.1067−0.4578−0.27400.2515−0.7895−0.21200.1888−0.37050.6872−0.19110.3330
31−0.3392−0.14980.36460.6204−0.18390.6582−0.31990.15510.35680.19230.1583
320.49650.5742−0.36910.1134−0.0984−0.8393−0.8090−0.2186−0.62020.11560.2307
330.67000.2042−0.03500.32040.31620.4469−0.86510.57230.03520.3410−0.2331
340.1773−0.59000.49320.3290−0.4802−0.31700.57590.5560−0.6513−0.95070.3155
35−0.2870−0.0699−0.0866−0.2916−0.14230.39220.77090.0266−0.43600.1056−0.1400
360.3352−0.3374−0.7176−0.32030.6644−0.01470.32150.2830−0.72520.41490.3521
370.0020−0.2064−0.5518−0.06550.2919−0.6655−0.6246−0.60070.75810.5035−0.1730
380.7213−0.04640.2616−0.73700.0446−0.4197−0.6358−0.5214−0.44550.35040.1515
390.07450.70630.36090.0959−0.1461−0.2016−0.18240.73240.1838−0.75030.2346
40−0.7435−0.45160.6738−0.1484−0.13910.37660.56370.3620−0.5014−0.25680.1497
Table 12. Neurons, weights, and biases for the second hidden layer of the ANN model in this study.
Table 12. Neurons, weights, and biases for the second hidden layer of the ANN model in this study.
First Hidden Layer
Neuron1234567891011121314151617181920
Second Hidden Layer1−0.1406−0.52200.26200.04330.04360.25050.07720.32520.4780−0.20890.12070.3259−0.0076−0.37070.23420.1582−0.40620.29410.2141−0.4805
2−0.06410.3851−0.05970.2090−0.29110.24930.05920.44140.10890.03000.0559−0.14370.08790.11580.15590.33650.3371−0.05600.2150−0.0775
30.11390.3216−0.00130.27870.03640.1226−0.40490.26080.1083−0.24190.1292−0.1896−0.0055−0.28480.26690.21510.06220.4145−0.0195−0.2681
4−0.39210.2468−0.24040.0857−0.1646−0.1200−0.2069−0.24920.0629−0.2256−0.39300.0401−0.0819−0.31410.02360.1730−0.2725−0.3016−0.0239−0.3218
5−0.30810.2905−0.25670.2731−0.2699−0.06620.0145−0.4032−0.3600−0.29340.07850.2710−0.08300.1712−0.08670.3642−0.0871−0.4488−0.11780.1331
60.05240.56940.3378−0.0142−0.13060.36850.19860.0699−0.35460.39590.21080.30060.36080.09190.2979−0.15220.15660.30830.29560.1799
70.15320.49360.1777−0.0361−0.39610.01010.00910.38640.2972−0.23800.1046−0.2154−0.12410.3974−0.0636−0.06130.36640.02900.4316−0.1164
8−0.29710.2172−0.4004−0.32540.2207−0.0646−0.01090.31930.33550.21380.1669−0.0251−0.1417−0.0079−0.1347−0.1352−0.1244−0.1763−0.23120.0903
9−0.2667−0.5043−0.43620.21410.12820.28500.44350.00800.3238−0.4930−0.3327−0.1548−0.17910.2022−0.3028−0.0363−0.1057−0.14860.1679−0.0762
10−0.3028−0.0350−0.0890−0.03540.34220.2009−0.26600.0356−0.18120.2848−0.14200.3929−0.22220.1075−0.0936−0.22890.30260.12790.0528−0.0947
110.2781−0.13490.04260.0235−0.2321−0.1963−0.17860.1776−0.4179−0.38840.0947−0.40870.0784−0.15270.19760.18730.37240.46150.38170.4288
12−0.33140.1522−0.0697−0.1476−0.27530.2824−0.4825−0.3862−0.2801−0.2798−0.42280.1474−0.2675−0.20880.0903−0.14680.0241−0.01790.02850.2227
13−0.0243−0.31370.32340.31650.2108−0.0599−0.1065−0.23750.08970.23860.2943−0.39560.4071−0.15380.18530.03920.1325−0.24160.2460−0.3155
14−0.4207−0.4424−0.46990.2896−0.16490.1521−0.17410.0379−0.2452−0.0617−0.2094−0.31170.30830.37930.33270.0777−0.4512−0.09470.22390.1765
150.13070.12570.0679−0.2171−0.19560.05430.18550.1408−0.0027−0.2647−0.4571−0.09340.06490.3730−0.0351−0.25350.45310.1238−0.03140.1276
160.13120.17670.2067−0.3377−0.12730.4508−0.0290−0.23010.2660−0.00510.2071−0.2144−0.0116−0.0501−0.35950.30490.02580.1592−0.11880.4361
170.01000.54490.32250.30890.16880.01450.23090.38350.2629−0.25700.2010−0.16870.35620.2249−0.33580.2508−0.22910.0774−0.20820.3325
18−0.2277−0.0677−0.0486−0.3494−0.30430.2349−0.1302−0.02910.2950−0.48880.2906−0.02580.24620.2469−0.46520.18560.08740.2405−0.3172−0.2777
19−0.10430.0572−0.05680.23160.01180.49080.11150.23160.18840.1855−0.1505−0.3323−0.3209−0.1386−0.10290.2485−0.10910.15140.44950.0753
20−0.2704−0.37220.21230.0795−0.18840.1651−0.4748−0.3302−0.1993−0.0650−0.20080.2241−0.14250.07710.0132−0.2348−0.1603−0.11790.07710.0409
21−0.45680.20470.0152−0.3129−0.42630.1829−0.33960.0342−0.30560.01350.2356−0.3022−0.16760.03940.33720.40710.1740−0.3581−0.0536−0.0808
22−0.0709−0.1581−0.28120.3837−0.17240.37190.38780.0189−0.2325−0.20060.4298−0.3183−0.32520.1380−0.0273−0.00100.10120.08700.3157−0.1116
230.07860.2550−0.39960.16170.4286−0.32930.2945−0.6878−0.05890.00380.3619−0.5059−0.3676−0.1545−0.00670.1836−0.0754−0.22920.09690.0506
240.04220.0068−0.19380.1053−0.27200.0101−0.02830.2374−0.2937−0.01220.13740.3433−0.17650.2998−0.05730.26040.13880.2053−0.20330.5564
250.25200.3857−0.3463−0.3316−0.2794−0.3172−0.0038−0.0044−0.4220−0.1891−0.2214−0.41160.0366−0.0049−0.07450.15950.01710.1823−0.03390.3030
260.02480.33860.00910.0098−0.26350.4802−0.0837−0.04360.06930.30550.16460.32710.37300.0243−0.40070.3458−0.15710.2863−0.10730.4638
27−0.1794−0.39310.3003−0.4865−0.33780.25000.3262−0.2257−0.0038−0.1156−0.0936−0.0671−0.2760−0.20800.41350.3486−0.20060.24830.2931−0.1503
280.16100.28780.2982−0.17950.29500.0791−0.3599−0.1901−0.17200.35460.30060.06990.12690.11910.08980.40070.0054−0.20890.28140.3455
29−0.2899−0.02510.14170.17990.2286−0.0092−0.2084−0.2463−0.28120.1181−0.3383−0.0005−0.36660.15270.2171−0.07630.1146−0.28530.3364−0.1187
300.02220.03680.34880.3453−0.36770.1315−0.24040.2383−0.0613−0.2496−0.04080.16190.0431−0.25580.06750.14430.44990.46380.28880.0531
31−0.0876−0.3058−0.3741−0.13720.29210.0369−0.27100.0701−0.0215−0.15880.3393−0.42070.36850.1215−0.36830.1407−0.0506−0.37040.28760.0111
320.23720.1311−0.10260.0616−0.16370.1571−0.13610.3294−0.19540.0055−0.0174−0.24630.2527−0.2722−0.42050.15780.0866−0.08760.40290.4013
330.30740.57960.26720.17060.04520.2762−0.1420−0.21470.00230.1806−0.1328−0.03930.39850.15860.18460.26570.27560.4651−0.26410.4316
340.15820.40170.12980.2009−0.2780−0.2077−0.1437−0.2995−0.38960.04550.05440.3745−0.05890.2888−0.20970.02060.1857−0.2535−0.51500.1893
35−0.2777−0.1416−0.0215−0.03030.1246−0.13450.0066−0.28760.4103−0.06670.1351−0.23390.0424−0.1074−0.14540.0655−0.5144−0.1339−0.3041−0.1637
360.08030.09870.42780.16210.00030.41690.1084−0.41870.30010.2790−0.27860.1928−0.2995−0.1375−0.4427−0.21690.1860−0.0640−0.06080.0502
37−0.02230.11870.12170.26290.2363−0.2881−0.1345−0.07200.0416−0.13440.17710.1962−0.29160.2605−0.2993−0.19790.1469−0.06770.2635−0.0695
380.33960.1540−0.2236−0.0463−0.17970.2892−0.38700.22190.2963−0.02500.28400.39570.1636−0.0511−0.3449−0.22590.1768−0.07750.10790.0958
390.02670.2729−0.1904−0.2475−0.35830.0162−0.3899−0.12790.1726−0.1347−0.13250.0407−0.1970−0.0160−0.4419−0.30020.14390.25750.0403−0.0307
Second Hidden LayerFirst Hidden Layer
Neuron2122232425262728293031323334353637383940Bias
10.0768−0.21150.0147−0.0994−0.0585−0.3543−0.17150.20620.32900.2921−0.5487−0.39780.5125−0.1825−0.0264−0.03280.3035−0.1804−0.20910.1079−0.1644
20.40920.53710.38040.01790.06400.3294−0.3631−0.2145−0.11890.3614−0.07150.36240.16090.46410.10060.4432−0.2340−0.34450.3538−0.02510.4134
3−0.3651−0.2190−0.09870.45800.27080.28570.29030.3870−0.2020−0.19090.1149−0.19170.2763−0.2033−0.41190.4892−0.10860.14830.09870.09310.2474
40.1350−0.29270.21750.1051−0.2861−0.0382−0.32530.32850.1030−0.17200.3702−0.2329−0.17970.16610.07310.0200−0.04780.08740.31690.1547−0.0280
5−0.24250.03640.0037−0.2898−0.14070.17710.2238−0.2577−0.41970.11410.2041−0.27620.07600.12360.01190.2809−0.1828−0.1005−0.36470.3120−0.0463
60.41420.18720.22360.3866−0.1688−0.30200.24440.3114−0.18080.21200.1345−0.2245−0.3553−0.0980−0.20910.35030.10500.39170.31770.01070.3189
70.02230.47780.31850.1326−0.2195−0.2555−0.4893−0.29620.17630.5453−0.0360−0.21700.21710.1882−0.41240.2948−0.24960.0910−0.05720.24940.3130
80.33330.09800.3247−0.2698−0.3194−0.00730.1240−0.4326−0.1819−0.0623−0.39730.09110.1929−0.02980.38430.0455−0.3282−0.2059−0.2972−0.3177−0.1035
90.35980.31100.2687−0.3894−0.00760.2168−0.2589−0.0210−0.0376−0.5393−0.2733−0.12990.26920.0982−0.00280.2771−0.16420.3826−0.42050.0409−0.1543
10−0.09530.06650.3227−0.3548−0.25850.1379−0.4123−0.2009−0.2568−0.26540.07340.27140.32400.1576−0.12060.12510.3158−0.3566−0.37260.2681−0.2014
110.04580.0744−0.1277−0.22800.0205−0.17420.3784−0.0088−0.10590.05760.15230.3100−0.27350.3601−0.22910.1558−0.4212−0.0450−0.11540.39180.3126
120.21470.15050.26280.0269−0.13390.34420.2972−0.13150.3019−0.0895−0.17760.0536−0.3029−0.18030.0692−0.05820.3272−0.3341−0.3433−0.2139−0.1349
130.3632−0.2730−0.2979−0.3590−0.2084−0.17680.34980.42460.19950.20200.09990.1912−0.39770.2876−0.1727−0.4491−0.29830.3381−0.08040.2067−0.1565
140.18280.3223−0.2847−0.1042−0.0538−0.0545−0.1139−0.01730.11470.1866−0.2594−0.14000.0958−0.23230.2645−0.03520.08400.2827−0.1351−0.2243−0.1283
150.32330.38460.22270.20520.18770.06430.29110.23690.33350.3638−0.0743−0.0556−0.42860.4726−0.29630.41340.30430.00390.0831−0.29600.3516
160.10760.4335−0.19870.39430.01080.16320.0260−0.2115−0.12590.42900.18360.0185−0.03540.0629−0.40090.39640.3355−0.2840−0.0638−0.30730.3290
170.0945−0.00160.09060.16550.3999−0.12660.1329−0.24000.0474−0.0254−0.32840.3026−0.45370.16510.2115−0.0801−0.28590.3218−0.15460.44950.3774
180.06560.0566−0.4382−0.04100.02710.10310.11070.4151−0.1047−0.1403−0.2433−0.39440.3803−0.01170.28070.22790.3073−0.24500.28140.2454−0.1655
19−0.2544−0.32250.27060.22890.14370.14390.28010.31420.0274−0.2264−0.3394−0.1081−0.40670.3922−0.38980.2621−0.2371−0.1866−0.00310.20400.3144
200.33720.15320.38160.14020.01520.4948−0.3293−0.49180.4262−0.5084−0.52530.30980.3345−0.1641−0.3705−0.15310.2976−0.1324−0.36100.0824−0.0927
21−0.3999−0.4606−0.34760.09860.00510.0378−0.0709−0.0559−0.23880.44240.1879−0.43410.0372−0.06030.11800.0371−0.14590.03300.32000.2854−0.1162
22−0.1028−0.3448−0.1991−0.16180.2872−0.32680.0497−0.3798−0.2699−0.49610.2881−0.3615−0.0233−0.25070.3174−0.27580.24840.06310.3159−0.2641−0.0715
23−0.3099−0.08730.00280.1242−0.6426−0.2623−0.20610.0927−0.0629−0.4159−0.0286−0.41370.1579−0.3793−0.0194−0.15210.3298−0.3829−0.0159−0.1715−0.0265
24−0.26920.30700.0665−0.2796−0.18680.42250.06450.31480.30300.39230.0418−0.1556−0.1325−0.1062−0.24330.1793−0.35190.28690.2944−0.21460.3654
25−0.1678−0.30270.3130−0.31950.2117−0.3045−0.3834−0.2386−0.41930.21010.00360.00730.3075−0.0898−0.0688−0.0589−0.0459−0.1477−0.1263−0.05330.0114
260.17220.2609−0.03870.01300.17320.3656−0.03090.16430.38810.38190.2843−0.2041−0.3372−0.1243−0.26280.1515−0.0367−0.3337−0.21970.18920.3510
27−0.0566−0.33340.3504−0.34450.02240.28360.2706−0.0897−0.1879−0.1814−0.42750.08050.00430.12900.2662−0.04840.20670.28210.09610.3103−0.1659
280.03550.29430.31860.03620.0576−0.0247−0.10030.01550.28630.16840.12700.2510−0.30910.03210.0459−0.01240.0469−0.35460.31170.23990.3114
29−0.04270.0004−0.3161−0.25630.0967−0.17340.2595−0.1448−0.1880−0.0135−0.1192−0.0035−0.35450.15590.0771−0.51050.2219−0.1221−0.1376−0.3183−0.0795
30−0.20310.1744−0.10120.03410.2824−0.31730.26540.2101−0.17530.30960.04690.1292−0.45040.21420.0907−0.2426−0.2603−0.1283−0.27570.44940.3747
31−0.1771−0.3055−0.2837−0.35440.1830−0.07310.29970.4541−0.03740.27080.15440.10150.17150.12720.1744−0.21460.16300.28230.2248−0.4986−0.1474
32−0.2729−0.4100−0.0402−0.23690.3211−0.4620−0.3468−0.43860.24520.1687−0.2917−0.16810.29850.36260.1712−0.09890.1732−0.0771−0.21580.05720.2211
330.1280−0.06780.42400.21890.35530.31100.33990.3294−0.03370.0175−0.03580.21610.2083−0.13730.09230.1798−0.01260.32940.30850.04940.2954
34−0.11810.48130.2657−0.2980−0.15400.0114−0.51480.30890.04640.26650.1773−0.2325−0.0546−0.28070.0767−0.1897−0.0663−0.04380.32820.16950.2822
350.45810.38940.1499−0.2715−0.2068−0.1187−0.1987−0.25650.3042−0.16920.01470.36370.11310.28920.23750.38630.37470.05340.07520.2193−0.1500
36−0.3805−0.29950.29110.13750.3437−0.38880.26400.0043−0.15040.4632−0.3192−0.19030.14910.45110.1718−0.08850.27260.36310.1532−0.24300.2411
37−0.12880.48780.3445−0.03690.1648−0.17320.1582−0.24560.24950.06180.16470.3431−0.29580.16730.0529−0.1069−0.26290.03940.28480.44270.3552
380.15150.2402−0.23840.38240.0711−0.19200.35470.2359−0.09210.14780.02400.0551−0.23220.15810.00750.0301−0.29630.2191−0.02860.10050.3033
39−0.0981−0.37110.02080.37210.2402−0.1475−0.4202−0.29500.0904−0.11110.02840.3176−0.03010.4134−0.05690.4671−0.1343−0.04260.32970.07810.2472
Table 13. Neurons, weights, and biases for the output layer for the ANN model in this study.
Table 13. Neurons, weights, and biases for the output layer for the ANN model in this study.
Second Hidden Layer Neuron
1234567891011121314151617181920
Weight−0.24250.10790.1664−0.3607−0.42380.17530.3360−0.2893−0.3836−0.26940.4022−0.1757−0.0361−0.22270.31600.29800.1107−0.28920.1082−0.4448
Second Hidden Layer Neuron
21222324252627282930313233343536373839Bias
Weight−0.3494−0.2602−0.12280.13380.25420.1623−0.12140.2947−0.25790.1706−0.14710.40890.41700.2894−0.26020.18020.08090.40360.33390.2847
Table 14. Comparisons of the reduced ANN models’ performance.
Table 14. Comparisons of the reduced ANN models’ performance.
Removed InputsRoverallMSEtrainMSEvalidationMSEtest
Density0.81650.01390.11270.0882
Refractive Index0.82950.00200.61250.1453
Sound Velocity0.84250.01270.13690.0369
Viscosity0.69390.05780.19310.1629
Molecular Weight (MW)0.79760.03170.09730.1132
Sound Velocity & MW0.84160.00530.07400.0903
Refractive Index & MW0.83210.00840.08470.0905
Density & MW0.72310.00580.14760.1427
Density & Sound Velocity0.88710.01050.06610.0532
Density & Refractive Index0.62700.03670.24190.1563
Density & Viscosity0.81410.00380.12020.0782
Refractive Index & Sound Velocity0.89220.00880.02950.0789
Refractive Index & Viscosity0.69700.00280.11460.1953
Sound Velocity & Viscosity0.79650.00800.10860.1048
Table 15. Neurons, weights, and biases for the first hidden layer for the reduced (refractive index and sound velocity) ANN model.
Table 15. Neurons, weights, and biases for the first hidden layer for the reduced (refractive index and sound velocity) ANN model.
NeuronTemperatureMolecular WeightNumber of CNumber of HNumber of NNumber of ODensityViscosityBias
1−0.11240.6348−0.18730.46450.10340.22430.0002−0.1052−0.1158
20.0615−0.3450−0.8294−0.1796−0.4868−0.23490.0533−0.31330.1328
30.5461−0.09270.67570.2881−0.60740.4297−0.4679−0.55590.1199
40.09270.5841−0.10740.5233−0.4246−0.4336−0.47540.5572−0.1090
50.1490−0.54440.60370.42920.4622−0.4950−0.2201−1.07980.3012
60.57570.2660−0.59930.0854−0.41680.5109−0.34040.86640.2324
70.51410.53790.40010.5429−0.24410.4389−0.51260.30490.1068
80.05630.21740.43280.56080.5297−0.1892−0.36290.41200.2365
90.4652−0.30000.11580.73210.3856−0.88090.34380.4824−0.0531
100.74180.3283−0.64380.71190.4064−0.8005−0.1244−0.39770.1852
110.22760.87590.61640.87470.04000.3592−0.87160.6410−0.2100
120.1087−0.72800.27880.0503−1.2021−0.03280.3785−0.02240.3546
13−0.52020.6770−0.0261−0.69150.8760−0.98410.03940.65080.1744
140.05310.87880.9902−0.0819−0.3536−0.1227−0.27120.71500.1844
150.24210.8376−0.64550.91840.69530.4072−0.27380.8454−0.1895
160.08900.40680.06350.50810.5596−0.4588−0.4789−0.85830.2146
170.2639−0.3405−0.6563−0.50880.17280.3697−0.4624−0.49430.1529
180.7855−0.35940.59130.11270.30870.15660.6119−0.38370.1080
190.1410−0.01140.7488−0.7060−0.69650.38230.6775−0.24020.2199
200.3099−0.6274−0.3260−0.1632−0.4577−0.4790−0.71530.01690.3601
210.49440.00260.5356−0.0617−0.03080.5477−0.6159−0.78860.3109
220.7639−0.12640.20890.9107−0.5838−0.72960.6672−0.2214−0.2152
230.11660.10450.3700−0.94110.87530.20540.30320.1617−0.0329
240.0609−0.1350−0.19210.3794−0.83100.62810.6988−0.69270.2667
25−0.65520.7355−0.42500.37710.2129−0.3710−0.0342−0.66650.3866
260.6890−0.56570.6196−0.2864−0.3520−0.27000.51650.5083−0.1347
27−0.67320.20300.5096−0.1973−0.9718−0.63910.6424−0.69360.2777
280.21730.5484−0.30940.06210.1741−0.65500.20730.4688−0.0303
29−0.69740.46560.1492−0.30260.77170.9050−0.7429−0.60890.1536
300.1526−0.4806−0.69570.8162−0.76430.47800.29270.75660.1915
310.0945−0.5134−0.23090.72050.9501−0.5224−0.55960.68690.0859
320.2465−0.2837−0.26530.6383−0.7153−0.4952−0.4650−0.56500.5163
330.0365−0.71520.60980.8256−0.3674−0.8255−0.13590.8580−0.2322
340.52080.2592−0.80570.17750.14580.3018−0.56600.3805−0.3196
35−0.2938−0.72550.79860.3319−0.03570.03260.26180.47530.2338
360.0461−0.59000.9098−0.7344−0.63090.5015−0.20170.57090.3059
370.11910.51900.5997−0.7229−0.38560.8398−0.3775−0.27600.2416
380.90210.4589−0.77670.2780−0.16350.1610−0.31350.6061−0.2489
39−0.2666−0.08040.13470.1864−0.79570.4831−0.7491−0.60820.6132
400.28500.7118−0.7793−0.2098−0.52470.3116−0.12190.4998−0.1063
Table 16. Neurons, weights, and biases for the second hidden layer of the reduced (refractive index and sound velocity) ANN model.
Table 16. Neurons, weights, and biases for the second hidden layer of the reduced (refractive index and sound velocity) ANN model.
First Hidden Layer
Neuron1234567891011121314151617181920
Second Hidden Layer1−0.11300.25000.3210−0.2440−0.08620.25000.11200.1610−0.0157−0.08310.0158−0.0696−0.1380−0.5570−0.2110−0.39100.0779−0.09250.27600.2720
20.19200.0169−0.0515−0.02430.28000.14900.07960.0199−0.0004−0.36600.0374−0.24100.0160−0.07730.12100.1660−0.4440−0.30500.2660−0.0588
30.33800.0986−0.22800.18100.06510.2510−0.1890−0.2970−0.0560−0.32700.1470−0.3060−0.01090.0110−0.05190.35300.0070−0.11300.02890.0852
40.0029−0.2870−0.15200.2410−0.0852−0.2720−0.30800.22900.0400−0.3450−0.1940−0.2340−0.22200.2550−0.2780−0.1950−0.2800−0.36300.10300.2020
5−0.00070.1900−0.30000.39900.0803−0.0425−0.09780.0110−0.1940−0.19100.2480−0.1630−0.41700.3800−0.03090.14700.3210−0.0858−0.31300.0712
60.0756−0.33300.3130−0.38700.35900.03500.39700.3560−0.05780.17600.37200.32000.25000.1930−0.2960−0.28600.23100.0960−0.12100.0331
70.1040−0.24200.40100.21600.0436−0.05600.13700.2910−0.1320−0.00030.2710−0.3060−0.04970.1310−0.12800.3250−0.37700.28000.15900.2920
8−0.4420−0.09480.29200.18100.41700.0836−0.30100.24100.4190−0.23000.3710−0.3380−0.10500.3020−0.16500.1830−0.05230.22300.1380−0.4550
9−0.21800.02900.37200.0618−0.26200.11100.4140−0.2540−0.2210−0.0907−0.02210.0773−0.4180−0.03770.03350.0189−0.50900.20200.3530−0.3040
10−0.27200.2590−0.1100−0.13600.27600.2640−0.1120−0.2390−0.20800.12400.45200.32100.2330−0.02120.0116−0.1730−0.33500.1470−0.15300.3590
11−0.25100.3300−0.2370−0.05990.1830−0.2230−0.0796−0.2410−0.07920.14900.03780.3650−0.2550−0.4200−0.06990.3110−0.3300−0.4470−0.34900.1100
120.03160.3330−0.3090−0.13500.05160.22100.0025−0.22200.3730−0.1260−0.1940−0.2900−0.15200.39200.0601−0.13900.24700.0685−0.06740.1090
13−0.0388−0.3170−0.2070−0.16600.2590−0.2280−0.2220−0.13300.12200.3330−0.11900.10200.06980.16700.13200.1160−0.0554−0.28000.1730−0.0591
140.01900.05550.14900.12500.0242−0.31400.00720.1240−0.01910.24400.0171−0.1740−0.3590−0.44200.2790−0.4100−0.0249−0.30600.0589−0.2580
15−0.2480−0.14400.17100.03320.2420−0.36400.25000.34900.2740−0.2760−0.1150−0.10000.1400−0.3710−0.2810−0.0389−0.0917−0.4830−0.0861−0.3190
160.2560−0.3850−0.1730−0.2310−0.2540−0.25300.49300.0831−0.1310−0.3690−0.1120−0.3630−0.3610−0.1680−0.01800.11600.22100.0690−0.1470−0.4690
17−0.0384−0.35900.5390−0.2420−0.3240−0.03940.20100.3080−0.47000.22400.00910.04010.05140.1080−0.20600.0955−0.42100.3750−0.08850.2980
18−0.2950−0.3000−0.18900.1410−0.24400.0490−0.2770−0.2220−0.2540−0.10500.2530−0.36000.06080.1560−0.31100.1850−0.13500.35400.01640.4220
19−0.2430−0.34600.0064−0.08900.1500−0.17400.3440−0.29300.3920−0.10100.25100.0933−0.1920−0.2670−0.2180−0.0743−0.0221−0.25400.0888−0.0590
200.3380−0.11200.0249−0.2560−0.22600.0755−0.09570.07230.1660−0.3140−0.1740−0.10300.2620−0.04290.3520−0.0546−0.5240−0.3140−0.28800.2930
210.3230−0.2700−0.12000.3670−0.12900.26300.12300.01280.15400.18100.3660−0.26400.05320.28700.2850−0.3410−0.0020−0.1740−0.1340−0.0187
220.0352−0.00880.5040−0.2230−0.0909−0.07490.3040−0.1270−0.1930−0.2020−0.12800.10800.3320−0.05130.0652−0.4480−0.13900.2900−0.31900.4650
230.1490−0.0417−0.01900.01930.11300.4670−0.3390−0.0389−0.68300.1560−0.26400.33100.1060−0.5160−0.0698−0.17000.03580.0629−0.38600.3450
24−0.28000.3840−0.23100.2820−0.0917−0.38100.1120−0.41700.40200.2990−0.18800.17700.1130−0.17400.31900.4320−0.1500−0.13400.1130−0.3120
250.1340−0.23300.37800.14800.38400.00490.42400.3490−0.15300.03340.19900.01840.19300.41500.0104−0.1710−0.2410−0.25500.2260−0.0698
260.1170−0.08380.2580−0.1580−0.19600.21700.08620.16300.0054−0.1030−0.34300.10800.32900.0529−0.2430−0.02900.1090−0.20800.0738−0.0798
27−0.0954−0.2500−0.23700.02410.2720−0.4600−0.2940−0.09710.01940.26400.3480−0.36000.20100.1520−0.03960.15200.2660−0.2790−0.0808−0.1420
28−0.4080−0.09860.1700−0.01380.1070−0.3740−0.09880.1680−0.3900−0.21100.2860−0.41800.24300.46100.3830−0.2890−0.1340−0.1910−0.1510−0.3600
290.2320−0.13600.0196−0.1240−0.2440−0.19900.31100.05400.26300.13900.0372−0.01380.1140−0.3000−0.33600.3680−0.00420.2600−0.36500.2610
30−0.2010−0.30900.03040.1500−0.1350−0.08720.0809−0.07790.3430−0.19700.2830−0.03690.2690−0.1400−0.37100.37000.36800.02760.03560.0485
31−0.01090.26200.0684−0.37300.3830−0.36600.15700.0693−0.3550−0.11100.03350.02520.0903−0.2630−0.19300.33300.2560−0.2560−0.08640.0487
320.13000.14500.2550−0.15800.38400.28000.02570.31900.3320−0.35700.01690.0013−0.21500.2470−0.34100.3160−0.3590−0.3670−0.0673−0.2200
330.1370−0.33000.5440−0.3770−0.15800.00800.23700.1800−0.5010−0.1450−0.42100.07730.0540−0.3490−0.1650−0.3110−0.11600.2390−0.0323−0.1220
340.33300.19000.1750−0.1040−0.31100.3150−0.2790−0.4850−0.06760.10200.3610−0.23400.1930−0.2300−0.29900.23500.04590.02520.3210−0.1690
35−0.2650−0.37800.27900.0695−0.0657−0.13100.05740.11300.24800.01320.0252−0.4200−0.03220.17100.2310−0.23500.3410−0.3970−0.0309−0.5530
36−0.41900.12700.2730−0.23800.24200.12300.45700.0449−0.17000.03610.4880−0.2730−0.2990−0.1060−0.18300.0858−0.05910.1280−0.29800.0320
370.1960−0.3640−0.33300.3330−0.05040.0437−0.1210−0.0168−0.27800.4350−0.27800.0938−0.3890−0.21700.29000.37500.39000.14800.01850.2540
38−0.12500.16900.3140−0.30800.3440−0.1110−0.3820−0.1420−0.04280.15100.3200−0.0004−0.3230−0.20000.3560−0.2130−0.2230−0.1290−0.1020−0.2820
390.2530−0.37500.1610−0.30100.43600.04150.19600.18000.1160−0.00070.2630−0.0127−0.84700.3670−0.29300.12300.07620.1090−0.29800.2700
Second Hidden LayerFirst Hidden Layer
Neuron2122232425262728293031323334353637383940Bias
1−0.27300.02410.05860.1230−0.36400.4180−0.08020.3160−0.25800.27900.02920.04450.01150.29100.01210.4050−0.18900.26200.2830−0.2870−0.1300
2−0.1890−0.2880−0.1730−0.2920−0.46800.09630.1120−0.1130−0.2070−0.0012−0.36200.16700.12800.3690−0.0649−0.10800.0911−0.36400.13600.0472−0.0060
30.0824−0.33200.08340.06890.21400.2460−0.3180−0.15200.02150.2540−0.1190−0.21500.13400.2970−0.26800.0341−0.1290−0.1840−0.35800.2840−0.2810
40.08930.24200.03070.31200.19100.30500.32400.35700.18800.3640−0.2310−0.2110−0.2420−0.0009−0.26500.2470−0.2180−0.37900.2430−0.23400.1110
50.2660−0.33400.1300−0.34800.3930−0.3470−0.30700.42400.21500.33100.24400.2470−0.0926−0.21600.17300.02440.5080−0.09090.2340−0.07190.3590
60.27100.0494−0.3220−0.31200.0197−0.0076−0.1170−0.0111−0.28000.13100.30400.3420−0.02850.25200.2470−0.36500.2370−0.52800.22300.3720−0.2220
7−0.0358−0.06070.28800.1010−0.15100.1890−0.0261−0.02770.3520−0.28600.39800.2860−0.02660.2570−0.4420−0.3840−0.0780−0.05690.27900.11000.3390
80.1120−0.07080.13200.2400−0.2110−0.04090.20300.2640−0.25000.12400.22400.1500−0.2300−0.1210−0.22900.1440−0.2230−0.00330.31000.3630−0.1380
9−0.22700.24400.16700.0033−0.1700−0.3710−0.14000.1080−0.27100.22200.13100.1720−0.33100.41300.17100.00560.2040−0.08900.05050.13200.4180
100.0282−0.2740−0.0571−0.0259−0.33900.20800.33700.44900.20600.2130−0.0665−0.1800−0.2940−0.2830−0.03820.16000.3900−0.46000.21400.3370−0.0764
11−0.02970.2340−0.17800.22000.21700.0996−0.15100.1020−0.2890−0.10400.4440−0.3110−0.27000.1840−0.15700.1150−0.2330−0.1200−0.24800.10600.3660
120.3220−0.21300.4240−0.34300.00360.2010−0.36300.25000.00030.52700.0604−0.11200.01870.00650.0328−0.35200.5280−0.04260.19100.2680−0.0493
130.35700.34500.3840−0.10800.50100.3540−0.25400.34800.46400.17700.2810−0.00300.03580.2670−0.0289−0.2560−0.19200.16000.31600.3140−0.2050
14−0.01150.4120−0.0639−0.09700.18100.3550−0.3820−0.36800.0968−0.2860−0.14900.2160−0.15500.2590−0.5380−0.13400.1890−0.1370−0.1760−0.39300.4180
150.0546−0.2080−0.27100.2860−0.2560−0.1530−0.2860−0.1730−0.33600.13300.1880−0.04710.2890−0.1130−0.14500.1470−0.24600.1130−0.2760−0.2520−0.0389
16−0.1790−0.4350−0.22600.0623−0.1380−0.27600.10100.37700.44800.3390−0.22900.4560−0.12000.47300.32300.2110−0.16300.08270.1550−0.16500.4360
17−0.02180.2120−0.02010.2200−0.0996−0.04910.1340−0.08550.0624−0.0366−0.2980−0.0259−0.08830.30300.0039−0.23200.19900.16500.20600.1050−0.0284
18−0.1460−0.00020.29400.1470−0.33100.0808−0.00470.22400.31400.1410−0.0268−0.32200.28800.29400.0685−0.0824−0.21200.09350.2750−0.0016−0.0134
19−0.14300.31900.4000−0.4270−0.0802−0.3670−0.14500.30600.0910−0.33400.2900−0.1600−0.25400.19600.3460−0.03260.09480.06270.1100−0.0681−0.0467
20−0.07570.26300.41000.1670−0.09390.32800.0689−0.10400.25900.2390−0.1910−0.05780.05170.36600.2950−0.56400.2400−0.23400.24600.0994−0.2430
21−0.33800.33700.29700.27300.31000.1590−0.1330−0.36400.2090−0.2960−0.36200.2770−0.09210.24400.2370−0.45400.4140−0.02640.38100.16500.3660
22−0.05180.2050−0.03060.32900.0575−0.35100.06220.1970−0.1130−0.1160−0.1040−0.22700.3280−0.24700.02660.1070−0.42300.0395−0.3440−0.0499−0.2410
230.08310.1980−0.00570.11800.41000.11900.2250−0.0615−0.40700.2060−0.0358−0.3850−0.26000.1350−0.37200.05460.00490.3020−0.3770−0.36200.3520
240.1650−0.3540−0.08700.19000.1660−0.3150−0.35800.29600.13600.23700.13900.37800.2800−0.03920.2460−0.1910−0.1820−0.38400.16000.0449−0.1320
250.0142−0.14000.06560.17700.17800.0130−0.2910−0.05200.24300.1050−0.00880.1500−0.21600.43400.08930.03480.08810.04790.1570−0.0406−0.0833
260.13500.16300.09750.1040−0.29400.2350−0.0977−0.07990.2770−0.36400.15800.0133−0.21100.09380.0750−0.1290−0.24300.00050.03420.15800.2940
270.28400.1460−0.2810−0.0268−0.16600.2460−0.03080.21300.26600.01970.27200.4390−0.17300.45300.0600−0.13600.2340−0.3820−0.06790.4550−0.0389
28−0.03670.3100−0.08070.1320−0.34800.3960−0.0883−0.2700−0.2210−0.0311−0.05970.00860.12700.29400.29200.38700.4010−0.1280−0.28700.32800.4150
290.18800.2810−0.1410−0.3250−0.33300.3290−0.2420−0.3820−0.15400.1030−0.52200.0084−0.0021−0.0271−0.3290−0.08180.20600.16600.2080−0.12100.3650
30−0.2180−0.34700.4060−0.0490−0.1130−0.09740.2960−0.2990−0.13800.04040.15300.3010−0.28900.20200.00730.23200.50000.05420.07970.37000.3550
310.32600.23100.0774−0.0236−0.2220−0.2830−0.33400.08380.1500−0.24400.17500.1870−0.3610−0.13300.3800−0.0907−0.05220.23300.4460−0.1470−0.0919
320.31000.13000.01150.02980.2330−0.2130−0.3090−0.13800.22700.2880−0.38500.2100−0.3050−0.25900.16100.23300.47200.0809−0.27200.01710.4060
330.24200.20100.25600.50100.5700−0.47400.0251−0.3590−0.4110−0.0292−0.0418−0.38600.1180−0.1380−0.2850−0.1780−0.4230−0.2220−0.26700.1840−0.0154
34−0.11700.3720−0.14900.3640−0.00360.0038−0.23900.1490−0.23700.2480−0.3150−0.1940−0.3910−0.0069−0.0771−0.4080−0.2070−0.10900.2070−0.14200.3260
35−0.3790−0.02760.1140−0.34100.11200.3910−0.0957−0.07650.36700.22000.1070−0.20500.2610−0.07860.1930−0.36800.0401−0.44600.34500.21600.4100
36−0.06780.26500.0287−0.2950−0.42100.41000.08420.26900.25600.21900.0226−0.0609−0.15300.07610.4220−0.1060−0.1370−0.13800.36300.4110−0.0845
37−0.0603−0.18000.1390−0.09830.11700.09860.1820−0.1960−0.0012−0.1290−0.25800.4070−0.10000.3660−0.1360−0.64700.3620−0.1590−0.16100.07240.4610
380.2140−0.0106−0.35900.32000.24700.0174−0.0384−0.1490−0.36000.3110−0.3310−0.15900.3370−0.1420−0.00170.0373−0.34800.3090−0.0060−0.3920−0.1270
390.41300.37400.0496−0.02220.2280−0.0449−0.03970.51300.20900.2650−0.57300.07930.1410−0.1630−0.2370−0.45700.45600.05820.50700.26900.3590
Table 17. Neurons, weights, and biases for the output layer for the reduced (refractive index and sound velocity) ANN model.
Table 17. Neurons, weights, and biases for the output layer for the reduced (refractive index and sound velocity) ANN model.
Second Hidden Layer Neuron
1234567891011121314151617181920
Weight−0.3520−0.0192−0.22400.22700.4230−0.22800.4020−0.31600.1970−0.43300.1430−0.1250−0.33300.4030−0.24600.1050−0.1970−0.0096−0.3040−0.3800
Second Hidden Layer Neuron
21222324252627282930313233343536373839Bias
Weight0.3080−0.28100.3210−0.0485−0.33400.3540−0.34200.17200.43400.3530−0.47100.2820−0.31300.23800.3790−0.22800.19700.00300.24700.3220
Table 18. Neurons, weights, and biases for the first hidden layer for the simulated ANN model.
Table 18. Neurons, weights, and biases for the first hidden layer for the simulated ANN model.
NeuronTemperatureMolecular WeightPcTcωTbFlash PointDensityViscosityVapor PressureBias
10.3791−0.8085−0.0754−0.91320.34180.5538−0.7291−0.6512−0.98600.4810−2.0023
20.47460.83020.8654−0.9043−0.7836−0.36860.25340.4265−0.6060−0.6293−1.8939
3−0.96781.0067−0.72320.78690.8227−0.3581−0.4781−0.09870.2129−0.07621.7755
4−0.7234−0.5354−0.83700.0832−0.9282−0.65810.8251−0.2978−0.0111−0.73441.7409
50.91340.44500.7416−0.5013−0.82550.3571−0.23020.18540.81220.8372−1.6066
6−0.25620.3493−0.74411.1380−0.5083−0.08300.2571−0.6824−0.20941.27231.2660
70.13110.9507−0.87310.2632−0.7579−0.55420.38770.0767−0.31771.0348−1.3825
8−0.15160.9403−0.8621−0.8131−0.16010.6607−0.29840.9383−0.43850.46681.3223
9−0.8780−0.3078−0.75290.6730−0.60460.45870.1584−0.8601−0.05970.93011.1700
100.55990.22380.52721.0303−0.04620.35350.59841.02330.32590.8472−1.0670
110.31670.47630.78300.09520.8615−0.11110.3839−0.8183−0.70261.0308−1.0445
12−0.1015−0.92640.45960.76200.6767−0.13000.76350.2730−0.9578−0.59400.8757
130.23971.1468−0.33410.59680.1786−0.11541.2483−0.7094−0.56890.5591−0.6607
140.4327−0.96180.6721−0.99270.3691−0.0770−0.98890.0254−0.4886−0.4149−0.6969
150.17520.16380.56400.2419−0.79751.00400.64300.4276−0.8962−0.4620−0.6266
16−0.0787−0.5875−0.08800.18420.33551.14671.07540.47670.1912−0.93350.5461
170.83100.3786−0.78860.1869−0.76420.29221.06740.47670.0537−0.9244−0.3521
18−0.17690.75070.17710.97790.17700.9286−0.92330.88000.11050.02040.1429
190.6280−0.15340.69220.04600.7548−0.8116−1.14840.79200.38560.3359−0.2327
200.8099−0.49140.2947−1.10760.1261−0.8730−0.0074−0.90000.42580.1104−0.0017
210.65380.10120.40830.9067−0.1955−0.8266−0.79450.83500.63010.7756−0.1463
22−0.0648−0.45600.0470−0.03730.97080.4811−0.8173−0.44840.75981.0971−0.1087
23−0.83420.7138−0.27140.80720.3474−0.6189−0.14200.7397−0.5940−0.8895−0.2606
24−0.4484−1.0355−0.6716−0.7935−0.3745−0.9331−0.5373−0.3708−0.2612−0.3261−0.2835
250.1710−0.9951−0.87050.76880.4988−0.2195−0.2865−0.85040.36410.56240.5392
260.3659−0.2618−0.24830.59680.51720.3471−1.03940.35350.7768−1.07280.6771
271.06690.40710.76140.23020.0432−1.13520.30360.0534−1.0864−0.44430.7538
280.1242−0.54010.7899−0.44720.67231.16110.4083−0.8136−0.53530.70560.7908
29−0.67940.0376−0.4322−0.58940.7935−0.6744−0.37040.4906−0.7393−0.7163−1.0006
30−0.44550.61580.74860.96450.64310.6781−0.56960.24610.82750.4248−0.9722
31−0.19220.25040.73960.56260.83590.6437−0.68170.9742−0.0605−0.2694−1.1254
320.9841−0.62481.3213−0.1506−0.5872−0.2341−0.7170−0.2421−0.19310.69311.1572
33−0.3461−0.6864−0.6441−0.12400.98060.8088−0.4116−0.06700.08431.1457−1.3049
340.74680.5503−0.83770.10241.0355−0.6581−0.6267−0.6024−0.0731−0.04911.4496
350.8815−0.3559−1.06400.25850.4074−0.0368−0.0374−0.47150.91780.73171.5280
36−1.0656−0.52780.35420.5742−0.6614−0.51600.78261.0751−0.0855−0.2976−1.5972
37−0.1119−0.1186−0.5653−0.6578−1.1791−0.85690.3319−0.77980.07060.9059−1.6048
380.76900.0281−0.2250−0.2455−0.70560.4202−1.29240.8117−0.1272−0.56491.8023
391.1043−0.0561−0.10440.89830.5968−0.28141.1681−0.0199−0.28360.29121.9324
400.74790.1511−0.39960.8378−0.34240.05790.9685−0.70350.77300.28402.1333
Table 19. Neurons, weights, and biases for the second hidden layer of the simulated ANN model.
Table 19. Neurons, weights, and biases for the second hidden layer of the simulated ANN model.
First Hidden Layer
Neuron1234567891011121314151617181920
Second Hidden Layer10.3675−0.4129−0.3632−0.3588−0.2176−0.02670.34840.3196−0.1697−0.1709−0.35830.32000.1792−0.1927−0.28040.1303−0.2889−0.10000.0965−0.0488
20.07230.08930.20590.2444−0.4186−0.4020−0.32640.18770.26260.2094−0.23860.2902−0.18400.2470−0.1751−0.12530.2915−0.02510.04530.2768
30.2520−0.04590.2321−0.48320.38680.2867−0.04230.0069−0.0826−0.1255−0.1334−0.13170.00780.1420−0.1252−0.32320.15810.02030.3040−0.0614
40.4175−0.35820.0947−0.26550.34400.11570.14000.2081−0.23980.1097−0.2520−0.16620.4494−0.14930.19730.2679−0.0214−0.0811−0.26370.4300
5−0.08790.3366−0.0763−0.3183−0.04770.0366−0.0852−0.33600.16900.0904−0.0626−0.0554−0.34620.20230.03540.3661−0.2668−0.3407−0.38640.2922
60.02090.3113−0.1321−0.2340−0.27500.3039−0.38660.38130.0887−0.1052−0.2553−0.21680.0243−0.0599−0.22730.3987−0.20260.1238−0.27770.0689
7−0.30800.2053−0.30010.0640−0.00900.3091−0.25790.3353−0.16850.31830.00140.12460.38190.18110.2232−0.00660.39300.21300.16980.3030
8−0.0073−0.25610.3986−0.1968−0.3530−0.2169−0.2618−0.04610.0599−0.28090.4086−0.2643−0.3737−0.2666−0.06330.10660.2228−0.0179−0.24730.2051
90.1161−0.04620.14930.1134−0.24540.25190.14860.24510.32230.1135−0.2602−0.40680.2248−0.1390−0.06940.22900.3209−0.27980.2943−0.0195
10−0.10060.4132−0.0918−0.02360.34830.1348−0.21900.0887−0.18460.07500.3235−0.22700.03890.1166−0.2783−0.08500.0414−0.0632−0.20190.5208
110.25390.16890.33850.01610.1556−0.01000.07440.21350.20240.00030.30230.31410.27110.20360.01490.28330.1908−0.22380.3016−0.2702
12−0.3592−0.04620.1392−0.3342−0.20280.34890.1980−0.2600−0.18740.0458−0.3512−0.08850.0658−0.35670.0946−0.29220.23320.0328−0.3001−0.1538
13−0.2886−0.3729−0.11690.28080.23410.12890.0902−0.29570.3308−0.2536−0.04840.25460.03420.29090.28950.42140.05930.31120.1030−0.1277
140.01380.2795−0.3605−0.02290.26480.1849−0.2092−0.16210.19220.05320.1551−0.02280.2506−0.21500.28700.22360.12810.3172−0.17410.1862
15−0.0233−0.1131−0.0705−0.30790.1192−0.19390.1198−0.2788−0.42360.29740.2018−0.2785−0.19200.3985−0.2390−0.24830.1623−0.0480−0.15190.3837
16−0.1013−0.10140.02390.12740.37780.3309−0.30280.1922−0.3277−0.0402−0.2290−0.0610−0.45480.0082−0.03640.12880.13840.2139−0.3628−0.1981
17−0.0689−0.02250.08280.0220−0.1723−0.0796−0.3003−0.41180.3329−0.24050.2664−0.42470.34930.14850.00300.14540.0842−0.30320.4409−0.3327
180.4089−0.14710.0197−0.14330.3188−0.2334−0.16660.30470.20300.18010.3162−0.25530.02710.1325−0.02310.1256−0.2650−0.4236−0.2432−0.2862
19−0.28530.4080−0.0046−0.40500.2562−0.14970.29160.3208−0.17970.0102−0.1906−0.0893−0.4142−0.10100.0319−0.34260.0227−0.0607−0.3114−0.2433
20−0.3529−0.3001−0.3084−0.0962−0.29810.0110−0.2989−0.1328−0.4082−0.00310.15240.18110.1314−0.42480.3186−0.0809−0.23050.2504−0.24080.1477
210.2171−0.0027−0.2431−0.4023−0.3551−0.28600.2289−0.2751−0.0777−0.1006−0.1067−0.04160.19490.1177−0.23600.3695−0.02460.1837−0.09990.1438
220.09980.21370.31270.21380.3085−0.31750.19660.3467−0.10560.03220.3431−0.19810.33990.2871−0.12440.2051−0.4745−0.1835−0.2246−0.2419
230.17050.00870.05970.1643−0.16160.46840.3213−0.31960.25980.2103−0.38000.12340.40290.03090.2855−0.28440.0771−0.3007−0.27440.0795
240.18220.04750.26430.34930.19440.3380−0.41320.2575−0.27320.0306−0.2744−0.06100.14960.0011−0.2392−0.22430.3115−0.10770.33260.3206
25−0.0879−0.3220−0.0218−0.43720.16750.40620.1276−0.20290.3063−0.1298−0.1556−0.3889−0.07040.1230−0.0527−0.2653−0.23060.11000.21570.1574
260.0664−0.27480.1905−0.4100−0.14110.4253−0.16760.32680.10000.2088−0.16350.08740.38950.2700−0.1899−0.2011−0.34170.44760.3642−0.2204
27−0.4107−0.01250.06550.2521−0.32570.2403−0.02770.1031−0.38350.03200.3745−0.2255−0.26330.1177−0.27630.22970.34430.1277−0.0795−0.1062
280.35690.00920.31490.27060.02900.1662−0.1881−0.3940−0.3172−0.40590.1257−0.23740.18720.0076−0.54900.32380.1654−0.34540.1546−0.3176
29−0.1188−0.1834−0.1737−0.1057−0.4265−0.25260.3211−0.3484−0.0458−0.2569−0.39110.1499−0.41550.1673−0.2108−0.0418−0.0798−0.16260.00030.4023
30−0.0506−0.0415−0.05950.2957−0.1181−0.47510.3638−0.29120.2586−0.30270.0055−0.02660.14680.1001−0.0611−0.0706−0.1491−0.37450.0767−0.4548
310.06590.09400.1306−0.4552−0.4220−0.0516−0.2078−0.26410.22160.1184−0.0141−0.50290.21380.1098−0.1704−0.0172−0.25730.18490.04800.4035
32−0.19160.1135−0.27700.2752−0.23720.0198−0.4276−0.11180.0289−0.4154−0.46340.2876−0.30360.3862−0.0791−0.27910.0479−0.20180.12990.3007
330.25030.3602−0.4307−0.34530.36250.46040.38200.19130.23900.0332−0.2940−0.04250.33090.03890.37550.01810.2091−0.2622−0.2552−0.2866
340.17690.2671−0.0335−0.1262−0.04520.3025−0.1254−0.51970.2315−0.0828−0.02410.2819−0.0379−0.16260.32030.2423−0.15770.2614−0.3634−0.1480
350.10220.0818−0.27430.08580.34710.00060.1746−0.4219−0.23150.2351−0.2417−0.1334−0.28560.0773−0.3517−0.1749−0.3622−0.0222−0.2148−0.2513
36−0.02600.31760.2087−0.3842−0.13370.33180.26310.2989−0.2377−0.29380.0150−0.3735−0.23420.18420.22010.1427−0.2026−0.1728−0.0199−0.1311
37−0.19500.24800.2322−0.2545−0.14680.1649−0.00720.18480.4621−0.0661−0.3462−0.2857−0.29610.0959−0.0986−0.45960.2270−0.19560.2720−0.0417
380.24850.35130.36960.0124−0.2639−0.4020−0.05100.3320−0.1695−0.23610.20630.19530.3381−0.22290.05770.19920.42410.2030−0.13370.2088
39−0.3112−0.2523−0.2838−0.34820.1553−0.09110.0574−0.14090.42940.3296−0.0641−0.1471−0.3774−0.1647−0.19760.2069−0.1889−0.04390.2317−0.0299
Second Hidden LayerFirst Hidden Layer
Neuron2122232425262728293031323334353637383940Bias
10.2226−0.26080.04530.18420.38020.32900.1709−0.06220.00240.0261−0.1708−0.32430.3717−0.2252−0.1437−0.1778−0.1762−0.02970.28950.0446−1.5575
20.2719−0.2400−0.11860.35180.24270.20260.3053−0.40830.3909−0.0256−0.1569−0.2815−0.0096−0.16020.2972−0.20610.3052−0.38430.06070.1708−1.4321
30.19530.0773−0.45340.30470.0785−0.4133−0.22280.36200.1284−0.26090.11740.4776−0.28470.22700.2265−0.41360.22570.42710.06810.0936−1.3873
4−0.09850.38880.21970.14700.4458−0.3077−0.16700.0169−0.02040.1570−0.38430.28750.34860.15090.2176−0.2237−0.01170.1510−0.04860.3012−1.2745
5−0.32320.3340−0.38410.11540.3722−0.2058−0.0271−0.3964−0.1351−0.1587−0.0116−0.2605−0.00210.1012−0.0967−0.2644−0.2715−0.17020.37400.29411.2221
6−0.0349−0.18200.00640.4890−0.3517−0.04570.11520.30510.3575−0.46470.02180.15920.1771−0.2999−0.04450.2098−0.3868−0.1852−0.00700.2247−1.1044
7−0.1340−0.39600.31510.02730.1221−0.3383−0.15580.3246−0.1259−0.0895−0.06620.21960.19960.24320.33990.4207−0.1968−0.1638−0.16260.27761.0731
8−0.1941−0.2767−0.1628−0.0663−0.1757−0.28900.38020.19990.2850−0.12520.30920.06910.17300.2758−0.3105−0.1401−0.29170.0089−0.38950.24000.9720
9−0.31020.19050.00540.40230.17200.27080.2719−0.16330.33190.30410.02210.00640.05600.31370.11410.42630.2396−0.28580.0791−0.4544−0.8734
100.1883−0.39680.3798−0.1657−0.38790.2453−0.23700.11950.25040.22410.2052−0.08530.23440.30720.10860.09180.2928−0.08680.49080.30900.8089
11−0.1266−0.1461−0.0775−0.1708−0.2759−0.18440.23050.2191−0.31200.29150.34440.29120.3031−0.3567−0.33340.26730.04250.2097−0.3751−0.3990−0.7268
12−0.2875−0.4759−0.2336−0.1944−0.0694−0.0782−0.35190.22340.3426−0.41380.2385−0.2739−0.24170.0311−0.11760.3008−0.18680.02180.2220−0.02070.6471
130.0945−0.04620.1885−0.3065−0.1065−0.17570.3354−0.23630.0205−0.29400.26960.04970.3650−0.15060.24800.2689−0.11050.0953−0.24620.13760.5823
14−0.33620.3231−0.1162−0.1109−0.3146−0.36020.1314−0.63080.1263−0.0394−0.02270.0407−0.3351−0.1949−0.40610.1358−0.2797−0.10680.25480.1865−0.4488
15−0.12030.16580.3925−0.00930.0588−0.3781−0.24020.23090.1481−0.27580.1338−0.3087−0.37970.20610.2861−0.0862−0.11710.27610.29220.36410.4241
16−0.15300.1709−0.1940−0.0764−0.21110.10850.19840.2636−0.49660.22160.27660.53850.3877−0.32520.17920.1171−0.29940.2245−0.1811−0.28160.3017
17−0.0077−0.14490.1344−0.05910.01050.07910.3838−0.2934−0.2890−0.1440−0.4468−0.3551−0.4352−0.24090.0351−0.21000.07760.0714−0.1592−0.09800.2468
180.2247−0.2536−0.04020.5374−0.25110.31670.4253−0.11680.3176−0.1549−0.22370.0989−0.2494−0.2615−0.2052−0.19120.4256−0.07610.0875−0.2739−0.1677
19−0.36510.17560.1493−0.29640.20360.1695−0.0040−0.2456−0.39010.1820−0.1683−0.39680.1064−0.0707−0.1593−0.41500.1546−0.2778−0.41540.03970.0908
200.28650.37050.30680.1852−0.2399−0.1673−0.05070.29600.02090.3317−0.3333−0.22800.2478−0.1563−0.2799−0.1685−0.18990.1223−0.21000.2353−0.0041
210.3414−0.29980.2059−0.2379−0.1476−0.21430.2478−0.2011−0.11150.4529−0.32830.22790.4156−0.36130.20460.23860.37570.0968−0.31740.01750.0343
22−0.1978−0.10630.08000.45000.10920.09550.3156−0.33780.0930−0.2154−0.2246−0.11730.2206−0.1957−0.03170.06030.3201−0.05770.25940.22140.1757
23−0.24090.10090.2247−0.1998−0.0660−0.43550.1241−0.0855−0.3083−0.1067−0.4979−0.2220−0.15950.29710.27650.13630.08060.3962−0.1198−0.13710.2539
24−0.40170.03010.31700.2072−0.0273−0.17840.1676−0.35400.21440.30800.12590.1311−0.05980.2239−0.2608−0.3756−0.03020.30050.33450.19810.3645
25−0.0359−0.18980.26510.0568−0.1194−0.2595−0.35070.1059−0.2591−0.22910.3213−0.28170.15680.3176−0.0997−0.30550.2819−0.41650.10840.2803−0.4166
260.1062−0.3647−0.18030.06080.3979−0.0412−0.13820.39100.38690.04770.1759−0.0841−0.0487−0.1390−0.3939−0.4250−0.2347−0.04890.0914−0.10040.4910
270.3074−0.1479−0.41090.1461−0.3724−0.42380.02040.0427−0.0552−0.1938−0.0776−0.35180.33550.25030.31140.18630.21450.0846−0.3659−0.1335−0.5483
28−0.1918−0.1527−0.1167−0.0149−0.0741−0.25270.37530.1018−0.33100.0413−0.12890.23940.09170.31110.2693−0.26380.3091−0.0517−0.0540−0.38650.6372
29−0.2643−0.20590.0341−0.1394−0.31180.3653−0.2946−0.2437−0.0694−0.1189−0.00100.44080.38020.11840.3108−0.4254−0.00290.25380.34490.0219−0.6989
300.4718−0.2049−0.00800.0787−0.44370.3237−0.1125−0.41330.02530.08640.1934−0.0010−0.02450.19390.35770.3385−0.0846−0.2007−0.24130.1990−0.8035
31−0.0856−0.18660.1180−0.0087−0.2604−0.22100.3461−0.4021−0.0308−0.33250.16620.0925−0.4058−0.10560.12600.0943−0.2518−0.3059−0.2800−0.20810.8609
32−0.3001−0.12030.09770.1225−0.1566−0.10780.03680.1114−0.1031−0.0498−0.18050.30140.2247−0.2616−0.3101−0.43210.30290.07820.31350.3556−0.9600
330.2239−0.3574−0.3657−0.1378−0.1040−0.1216−0.2233−0.41160.0662−0.0371−0.48250.40740.15290.2037−0.0707−0.04940.21550.2578−0.24370.17571.0187
340.03680.2221−0.3119−0.32750.11820.3658−0.1383−0.0264−0.42550.4009−0.2236−0.33850.4065−0.0556−0.0839−0.0818−0.34090.2607−0.13980.19461.0709
35−0.1744−0.06380.2230−0.10080.0888−0.3382−0.16800.2853−0.2672−0.24390.12510.25450.23140.14700.1274−0.36690.2321−0.2944−0.2316−0.39281.1753
360.13500.2189−0.1752−0.06350.29240.3223−0.26800.00140.2019−0.0811−0.2209−0.2380−0.2323−0.3617−0.0488−0.3692−0.3753−0.33770.0469−0.2969−1.3156
370.20990.12710.0223−0.26070.37210.34130.1485−0.2894−0.04290.1758−0.4344−0.0366−0.36910.34440.42410.29950.0680−0.14130.13360.1817−1.3629
380.3851−0.2410−0.0101−0.17860.31640.37780.12640.23870.2891−0.27000.07430.19230.2754−0.05410.2902−0.1209−0.22820.0630−0.0635−0.30891.4434
39−0.06160.33900.45480.19880.32290.21960.12330.4229−0.28090.2354−0.1973−0.12150.2145−0.16000.02290.2061−0.1263−0.1236−0.2105−0.4252−1.5342
Table 20. Neurons, weights, and biases for the output layer for the simulated ANN model.
Table 20. Neurons, weights, and biases for the output layer for the simulated ANN model.
Second Hidden Layer Neuron
1234567891011121314151617181920
Weight0.8320−0.3520−0.62360.83000.21830.48360.33381.0340−0.4871−0.9513−0.5188−0.22290.5155−0.72440.1526−0.65130.0370−0.3207−0.3903−0.3953
Second Hidden Layer Neuron
21222324252627282930313233343536373839Bias
Weight−0.7215−0.7665−0.76200.21720.26570.8019−0.3311−0.7170−0.33790.1952−0.40100.45230.8320−0.7341−0.23460.42360.2719−0.70390.0767−0.7918
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Alluri, V.S.P.V.; Nguyen, W.; Henni, A. Determination of the Dissociation Constants (pKa) of Eight Amines of Importance in Carbon Capture: Computational Chemistry Calculations, and Artificial Neural Network Models. Liquids 2023, 3, 214-245. https://doi.org/10.3390/liquids3020016

AMA Style

Alluri VSPV, Nguyen W, Henni A. Determination of the Dissociation Constants (pKa) of Eight Amines of Importance in Carbon Capture: Computational Chemistry Calculations, and Artificial Neural Network Models. Liquids. 2023; 3(2):214-245. https://doi.org/10.3390/liquids3020016

Chicago/Turabian Style

Alluri, Venkata Sai Priyatham Varma, William (Hoang Chi Hieu) Nguyen, and Amr Henni. 2023. "Determination of the Dissociation Constants (pKa) of Eight Amines of Importance in Carbon Capture: Computational Chemistry Calculations, and Artificial Neural Network Models" Liquids 3, no. 2: 214-245. https://doi.org/10.3390/liquids3020016

Article Metrics

Back to TopTop