Constr. Mater., Volume 3, Issue 2 (June 2023) – 8 articles

Environmental pollution is one of the most serious and global problems for humans. Photocatalysis is a promising technology to control environmental pollution via the utilization of semiconductor materials as a photocatalyst. In this study, iron-doped TiO₂ nanotubes (Fe/TiNTs) with an increased photocatalytic effect at longer wavelengths compared to undoped TiNTs were used, and the effect on the early hydration and mechanical properties of the main clinker phase tricalcium silicate (C₃S) was investigated for the first time. Prior to the incorporation of nanotubes into C₃S, it was treated with a supersaturated Ca(OH)₂ solution. The addition of 1 and 2 wt.% of Fe/TiNTs into the C₃S system significantly accelerated the course of hydration. The degree of hydration for the hydration products after 8 h, 1 d and 7 d have improved. The enhancement of compressive strength after 7 d, 14 d and 28 d were observed compared to normal TiO₂ nanotubes (TiNTs). Treating Fe/TiNTs with a supersaturated Ca(OH)₂ solution revealed a stronger interaction between Ca²⁺-ions and nanotubes. Fe/TNTs were synthesized via a modified hydrothermal process. The study shows that Fe/TiNTs can be used as a nanomaterial in cement-based building materials due to their enhanced interaction with the system. Full article

Early-age cracking during the plastic stage is unsightly and a cause of future durability problems. This paper investigates the effects of various simple curing methods used in practice to enhance early-age concrete cracking performance, including covering concrete with a plastic sheet and wet hessian fabric, surface power floating and use of cold water in the mix. The benefits offered by the use of three standard curing admixtures (Safecure Super concrete, Safecure Super 90W-10%, and superplasticizer), as well as recycled tire steel fibres at 40 kg/m³, are also examined. A digital image processing (DIP) technique is used to measure the crack widths, whilst the temperature in the concrete is measured via a thermocouple. The results show that all the concrete curing methods are successful in restraining micro and plastic shrinkage cracks, although the use of recycled tire steel fibre (RTSFC40) is most effective in eliminating micro and plastic shrinkage surface cracks. All of the examined methods are compared in terms of the speed and cost of application, quality of the surface finish and environmental credentials. This study will inform best practice on enhancing the durability and sustainability of concrete structures, particularly for slab-on-grade applications. Full article

Alkali–silica reactivity (ASR) is one of multiple reactions responsible for premature loss in concrete infrastructure service life. ASR results in the formation of expansive, white-colored gel-like material which results in internal stresses within hardened concrete. ASR-induced stresses result in concrete cracking, spalling, and increased reinforcement steel corrosion rates. The main objective of this research is to improve the conditions of concrete infrastructure projects by mitigating ASR’s damaging effect. The expansion of accelerated mortar bars poured using fine aggregates collected from different sources is measured versus time to evaluate the aggregates’ reactivity. Different percentages of supplementary cementitious materials (SCMs), including class C fly ash and microsilica, were used in remixing mortar bars to evaluate the efficiency of different types of SCMs in mitigating mortar bar expansion. The research findings showed that SCMs can mitigate ASR, thus decreasing mortar bar expansion. The efficiency of SCMs in ASR mitigation is highly dependent on the incorporated SCM percentage and particle fineness. Silica fume, having the smallest particle size, displayed higher rates of ASR mitigation, followed by fly ash. The outcomes of this research will assist design engineers in avoiding future losses due to ASR cracking in concrete infrastructure projects, and reduce the excessive need for maintenance, repair, and replacement activities. Full article

Additive manufacturing is becoming increasingly important in the construction industry. Wire arc additive manufacturing (WAAM) can be integrated into the selective paste intrusion (SPI) to enable the simultaneous printing of reinforced concrete. The bond behavior of a WAAM reinforcement was investigated with pull-out tests and compared to alternative reinforcement types to analyze the stress transfer between the different components. In the first step, the surface of all the reinforcement types was recorded using a laser-based line scan measuring system. This permits the evaluation of the surface parameters, such as the surface roughness R_q, or the related rib area f_R. The WAAM reinforcement showed a bond behavior in the pull-out tests that was comparable to a reinforcing steel bar. Both the bond stresses achieved, and the occurring scatter of the measurement results at the characteristic slip values were almost the same. Even without existing transverse ribs, the WAAM reinforcement reached maximum bond stresses similar to the reinforcing steel. An evaluation of the surface roughness revealed a linear relationship with the maximum bond stress achieved with a logarithmic scaling of R_q. The bond work W_τ, which is a measure of the system stiffness, showed that WAAM reinforcements and reinforcing steel bars have approximately similar behavior. Full article

Analysis of the use of reinforced concrete structures confirmed the destruction of reinforced products based on Portland cement due to stray currents, which makes it impossible to achieve the required durability and reliability of structures. The present work shows the results of a study on the diffusion permeability of samples with different degrees of electrical conductivity. The relative value of the electrode potential was measured by the open circuit potential method. The novelty of this work is its analysis of the quantitative and qualitative characteristics of the structure of the mineral matrix with specified electrical properties after long-term exposure to electrochemical corrosion. In this work, an assessment was carried out, for the first time, on the effects of electrochemical corrosion on modified composites with predominantly electrically conductive and electrically insulating properties. An increase in the electrical conductivity of the composite was found to reduce the potential difference. The use of such composites helped protect the reinforcement from electrochemical corrosion. Full article

Dehydration of concrete floor slabs is a critical step to ensure that the flooring material adheres properly and that there is no moisture-related damage to the floor after installation. Dehydration in a cold climate is often a slow process, which can have a big impact on the overall duration of the construction project, and corresponding measures are often taken to accelerate the drying process, especially in constructions exposed to a cold climate. One common method, typically used to accelerate dehydration in cold weather, is to introduce internal heating cables into the slab. This method reduces the dehydration time, but may not be the best solution from a sustainability perspective. This paper presents a concept study of concrete flooring in a cold climate from a cradle to practical completion perspective. The study focused on the environmental and material aspects of the dehydration of concrete floors in a cast-in-place house. This paper showed that concretes with high water-cement ratios, which are typically preferred due to their low CO₂ emissions, may require measures for accelerated dehydration, which ultimately results in a higher environmental impact. The importance of environmental studies is also highlighted to fully understand the environmental aspects of construction. Full article

The bleeding of cementitious materials corresponds to the settlement of the granular skeleton accompanied by the accumulation of water at the surface (bleed water). Part of this water (internal bleeding) remains trapped under the aggregates (sand or gravel) or the reinforcements. The excess of this trapped water can weaken the bond between the cementitious matrix and the aggregates (or the reinforcements), which affects the mechanical performance and durability of the material. This study aims to investigate the effect of excessive bleeding induced by superplasticizer on the properties of mortars. For this, a study of cement paste bleeding in the presence of superplasticizer was carried out. The effects of the water-to-cement ratio (w/c) and the superplasticizer (SP) dosage on this bleeding have been characterized. Then, the influence of the proportion of sand on the bleeding was examined by varying the sand/cement (s/c) ratio. The water trapped by sand (internal bleeding) was determined by the difference between the external bleeding on the cement paste and the external bleeding on the corresponding mortar. The results show that the internal bleeding increases with the s/c ratio and the SP dosage, until it reaches a plateau. The effect of the internal bleeding on the mechanical properties and the porosity of the mortar were then examined. Microscopic observations were made to assess the quality of the paste/sand bond. The results showed that the internal bleeding causes a degradation of the paste/sand bond (a more porous bond), resulting in a decrease in the mechanical strength (by 30% for compressive strength and 25% for flexural strength) of the hardened mortar. Full article

Earthen construction is one of the world’s oldest and most popular construction methods, and it is still the target of prejudice due to the loss of ancestral knowledge. Due to the need for more effective and healthy building solutions, this study conducted a survey to determine the interest and knowledge of construction professionals regarding sustainable and natural materials and building techniques to understand how open these professionals are to changes in their working methods and if they identify urgency in that change. With the intent of proving the durability of earthen construction materials, laboratory research was developed which involved the preparation and performance evaluation of samples of earthen elements from the most-used techniques: rammed earth and compressed earth blocks. This evaluation was performed using the accelerated erosion test, simulating periods of rainfall and drying, and the post-test loss of resistance was also evaluated. According to the results obtained from the research survey, there is a predominant lack of knowledge about earthen construction and other traditional and sustainable materials. On the other hand, the experiments demonstrated that earthen construction can be durable when using either a small percentage of stabilizing material or a covering plaster. Full article