Next Article in Journal
Flight Anomaly Detection via a Deep Hybrid Model
Next Article in Special Issue
Layout Analysis and Optimization of Airships with Thrust-Based Stability Augmentation
Previous Article in Journal
Vibro-Acoustic Modelling of Aeronautical Panels Reinforced by Unconventional Stiffeners
Previous Article in Special Issue
Modelling and Stabilisation of an Unconventional Airship: A Polytopic Approach
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Effect of Lifting Gas Diffusion on the Station-Keeping Performance of a Near-Space Aerostat

School of Aeronautics and Astronautics, Central South University, Changsha 410083, China
*
Author to whom correspondence should be addressed.
Aerospace 2022, 9(6), 328; https://doi.org/10.3390/aerospace9060328
Submission received: 21 May 2022 / Revised: 16 June 2022 / Accepted: 16 June 2022 / Published: 18 June 2022
(This article belongs to the Special Issue Mission Analysis and Design of Lighter-than-Air Flying Vehicles)

Abstract

:
During the long-endurance flight of a near-space aerostat, the characteristics of lifting gas diffusion have a great influence on the flight altitude adjustment and station-keeping performance. Thus, in this study, a lifting gas diffusion model and a dynamic model that consider thermal effects, which had not been studied in similar models before, were developed. The dynamic model and thermal model were validated by historic flight data, and the calculated lifting gas diffusion results were compared with the experimental data of other researchers. The variations in the flight endurance, flight altitude, lifting gas diffusion rate, and diffusion coefficient of a near-space aerostat were analyzed. The effects of the ratio of porosity to tortuosity and envelope radiation properties on the mass of the lifting gas and flight altitude were considered in detail. To analyze the effect mechanism of the ratio of porosity to tortuosity and the envelope radiation properties, the envelope and gas temperature, as well as the gas pressure, were studied. The results show that the lifting gas diffusion rate and diffusion coefficient are very sensitive to the change in the ratio of porosity to tortuosity and envelope temperature. The results obtained from the analysis of the lifting gas diffusion can lay a solid foundation for improving the flight performance of near-space aerostats and for providing improved design considerations for aerostats.

1. Introduction

In recent years, more and more scientific research institutions and scholars have focused on utilizing lighter-than-air aerial flight vehicles as pseudo-satellites operating for extended durations of time in near space to achieve relevant military and civilian tasks previously accomplished using traditional spacecraft [1]. A near-space aerostat is an ideal high-altitude platform for Earth observation, homeland security, data and communications relay, and the relay of communications that need the regional station-keeping ability to adapt to multiple environments [2]. Whether in national defense or economic activities, a near-space aerostat can be used as a supplement to “space-based” vehicles.
For a near-space aerostat, its station-keeping performance is its main technical advantage [3]. To address station-keeping performance requirements, many scholars and researchers have carried out theoretical studies and simulations [4]. Ramesh et al. [5] evaluated the stationary performance of a dual-balloon system and a balloon–stratosail system and compared the best ranges of wind conditions for tether systems. The results showed that the dual-balloon system is more suitable for passive control in a wind field with quasi-zero wind layer and that a balloon–stratosail system can carry out appropriate wind resistance control. Van Wynsberghe et al. [6] presented an innovative design for a stratospheric platform that can achieve long-endurance horizontal station-keeping using electrohydrodynamic thrusters. Another innovation of this paper was its presentation of a wireless energy supplement scheme. Yang et al. [7] proposed a new conceptual design method and fuzzy adaptive backstepping control approach to adapt to inaccurate and non-real-time high-altitude wind field data. Based on the phenomenon of a quasi-zero wind layer at the bottom of the stratosphere, Du et al. [8] proposed the flight altitude adjustment method based on charging and discharging air in an aerostat ballonet to realize regional stationary flight or fixed-point air parking.
These studies provided a theoretical base for designing and controlling a near-space aerostat. These studies were mainly focused on flight performance, station-keeping endurance, and float altitude control. However, discussions of the effect of lifting gas diffusion on the station-keeping performance are rare. We all know that lifting gas diffusion is one of key elements in the design of envelope materials. Hall and Yavrouian [9] analyzed the effect of lifting gas loss on the internal gas pressure of a Venus super-pressure balloon (see in Figure 1). As a typical super-pressure lighter-than-air vehicle, the balloon’s net buoyance and maximum flight altitude will gradually reduce with the loss of lifting gas. The loss of flight altitude adjustment capability means that there will be a reduction in maneuverability. During flight, the supplementation of lifting gas is almost impossible for high-altitude aerostats. Therefore, the lifting gas diffusion directly determines the success or failure of long-endurance missions carried out by near-space aerostats. The thermal performance and leakage of lifting gas have a direct impact on the flight altitude control of aerostats. The question of how to fully understand the temperature, pressure, and diffusion of lifting gas is one of the most important issues needing to be addressed in the process of the real-time flight control of an aerostat.
Inspired by studies of gas diffusion in the microelliptical groove gas diffusion layer, porous gas diffusion layer, and fibrous materials [10] under the influence of lifting gas loss, the gas diffusion characteristics of the envelope were studied here. The envelope is one of the major structural parts of a near-space aerostat. It is used to maintain the aerodynamic shape of an aerostat by filling it with lifting gas. The envelope material of a high-altitude aerostat is composed of a laminated membrane [11]. An envelope is made of multi-layer materials, including wearable, ultraviolet, lifting gas barrier, UV protection, anti-aging, and load-bearing layers, as shown in Figure 2 [12].
To date, the study of lifting gas diffusion caused by composite damage and external load has been largely focused on the mechanical properties of carbon-fiber-reinforced composites and the mode of crack propagation [13]. In one study, the lifting gas diffusion of orthogonal carbon-fiber-reinforced composite laminates under biaxial loading was measured [14]. The experimental results showed that the lifting gas diffusion coefficient on the surface of the laminates has a clear relationship with the load. In order to analyze the influence of thermodynamic properties and material matrix cracks, a diffusion model was developed obtain the diffusion coefficients of the composite laminates. It was found that the smaller the ply angle of the material matrix was (the reference values were 45°, 60°, 75° and 90°), the larger leak conductance at the crack intersection would be [15]. Based on the Lennard–Jones interactions, Thornton et al. [16] proposed a transport model of gas in various media to predict the minimum pore size needed for Knudsen diffusion. Yao et al. [17] studied the lifting gas leakage mechanism of damaged flexible composite materials and analyzed the influence of different types of damage on lifting gas leakage; this was of significance for the study of the damage-induced lifting gas leakage of envelope materials. The structure of an envelope material is different from that of carbon-fiber-reinforced composite laminates, and the mechanism of lifting gas diffusion caused by damage is different [18]. To study the lifting gas diffusion of an envelope material, it is necessary to establish a corresponding theoretical model according to its structural characteristics and use new experimental methods to obtain more accurate results.
In view of the lightweight envelope material used and the harsh high-altitude thermal environment, the envelope of an aerostat is required to be processed very thinly, and the multi-functional composite layer has different mechanical properties that will lead to delamination and the damage of the envelope after being subjected to alternating thermal stress. Therefore, the study of the lift gas diffusion characteristics of flexible envelope materials is important for improving the station-keeping endurance and safety of near-space aerostats [19]. Based on a literature search, it can be seen that the pressure difference between the internal lifting gas and the external atmosphere can directly affect lifting gas diffusion at high altitudes. The gas pressure difference is directly related to the thermal performance of the lifting gas and the envelope [20]. Many experts and scholars have studied the thermal performance of aerostats [21]. Xiong et al. [22] proposed a simplified thermal model suitable for engineering to assess the steady equilibrium temperature in aerostats at float altitude. In addition to the temperature characteristics of the lifting gas and envelope, the thermal performance of the electronics within the system also needs to be studied to optimize the used thermal control methods.
From the abovementioned literature review, it can be seen that most studies to date have mainly focused on several key issues, such as the flight performance, station-keeping endurance, and thermal performance of near-space aerostats and the gas diffusion of flexible composite materials. However, investigations of the effects of the lifting gas diffusion on the station-keeping performance of a near-space aerostat have been rare. During the long-range flight of a near-space aerostat, it is necessary to understand the lifting gas diffusion characteristics. In this study of a naturally shaped super-pressure balloon made of laminated composite materials (as shown in Figure 2b), a lifting gas diffusion model and a dynamic model that considered thermal effects were developed. A numerical model was used to analyze the lifting gas diffusion and to study the effects of the envelope properties on the station-keeping endurance of the aerostat in detail. The contributions of this paper are summarized as follows: (1) A lifting gas diffusion model that considers thermal effects was established. The temperatures of the envelope and lifting gas were taken into consideration in this paper for the first time. The influence of the envelope thickness variation was considered in the theoretical model to make the lifting gas diffusion model more precise. (2) The effects of the main air tightness parameters of the envelope and the envelope radiation properties on the lifting gas diffusion coefficient were analyzed. The relationship between gas diffusion and flight duration was analyzed. The relationship between lifting gas diffusion and flight endurance and the mechanism of the variation of the gas diffusion coefficient were studied. The results obtained from the analysis of the lifting gas diffusion can contribute to improving the flight performance and station-keeping endurance of near-space aerostats and to providing improved design considerations for aerostats.

2. Theoretical Model

2.1. Lifting Gas Diffusion Model

In near-space aerostats, the lifting gas diffuses out by passing through the envelope material. Figure 3 represents the mass transfer mechanism of lifting gas through an aerostat envelope.
Considering Figure 3, which demonstrates a case with a small envelope thicknesses, the gross mass of the diffusion lifting gas can be calculated as:
m d i f f u s i o n = M g a s n d i f f u s i o n
where M g a s is the lifting gas molecular weight in kg/kmol.
n d i f f u s i o n is the amount of lifting gas that diffuses. The differential amount of lifting gas that diffuses can be calculated as:
d n d i f f u s i o n = N H e A b d t
where N H e is the lifting gas flux and A b is the effective cross-sectional area of heat and mass transfer.
N H e = D r e a l P g a s P a i r ( C i n C o u t ) d e n v
where C i n and C o u t are the lifting gas and external atmosphere concentrations inside and outside of the aerostat envelope, kmol / ( m 2 s ) , respectively. C i n and C o u t can be calculated as:
C i n = ρ g a s / M g a s
C o u t = ρ a i r / M a i r
where P g a s and P a i r are the pressures of the lifting gas and external air, respectively; ρ g a s is the lifting gas density; ρ a i r is the density of external air; M g a s is the molecular weights of lifting gas; M a i r is the molecular weights of external air; and d e n v is the thickness of the near-space aerostat envelope.
The transfer velocity is critically affected by the real effective diffusivity. D r e a l is the real effective diffusivity, and it can be calculated as [24]:
1 D r e a l = 1 D g a s _ a i r _ e f f + 1 D K _ g a s _ e f f
The effective diffusion coefficient can be calculated by considering the molecular and Knudsen diffusions [25]. D g a s _ a i r _ e f f and D K _ g a s _ e f f are the effective molecular diffusivity and effective Knudsen diffusivity, respectively.
Due to the envelope being made of porous material, D g a s _ a i r _ e f f can be calculated by considering the gas diffusion through the porous solid material.
D g a s _ a i r _ e f f = ε e n v τ s s D g a s _ a i r
where ε e n v is the porosity of the envelope material and τ s s is the tortuosity. Tortuosity is used in an attempt to account for the longer distance traversed in the pores. Tortuosities usually range between two and six, averaging about three [26].
D g a s _ a i r is the molecular diffusivity, which can be calculated from the Chapman–Enskog equation [27]:
D g a s _ a i r = α 1 T e n v 3 / 2 P g a s r c o l 2 Ω g a s _ a i r ( M g a s + M a i r M g a s M a i r ) 1 / 2
where α 1 = 1.8583 × 10−7 [28], T e n v is the envelope temperature, P g a s is the pressure in atmospheres, r c o l is the collision diameter, and r g a s and r a i r are the collision diameters of the lifting gas and ambient air, respectively.
r c o l = 1 2 ( r g a s + r a i r )
The dimensionless quantity Ω g a s _ a i r is more complex but usually of an order of one [26]. The detailed calculation is affected by the interaction between the two species [29].
The effective Knudsen diffusivity D K _ g a s _ e f f can be calculated as:
D K _ g a s _ e f f = ε e n v τ s s D K _ g a s
For a porous envelope material, the Knudsen diffusion is the main influencing factor [30].
D K _ g a s = 2 3 r P 8 R u T e n v π M g a s
where R u is the universal gas constant ( 8314.47 Pa m 3 / ( kmol K ) ) [31] and r P is the pore radius, which is in the order of 10−6 m.
Based on Equations (7) and (10), we can obtain the porosity of the envelope material and tortuosity, as the air tightness parameters of the envelope material directly affect the effective diffusion coefficient. Analyzing the effective diffusion coefficient in the mass transfer equation as a function of the ratio of porosity to tortuosity, we can obtain the intermediate variable used to indicate the air tightness of materials.
r a t i o = ε e n v / τ s s

2.2. Balloon Geometry

The expansion of the balloon as a function of altitude can safely be assumed to be governed by the ideal gas law. According to the ideal gas law, the state of an amount of gas can be determined by its pressure, volume, and temperature using the equation:
V b = { V g a s V g a s V max V max V g a s > V max
where V b is the volume of the balloon in the current flight environment, V g a s is the volume of lifting gas after free expansion in the current flight environment, and V max is the maximum design volume of the balloon.
V g a s = m g a s R g a s T g a s P g a s
where m g a s is the mass of the lifting gas, T g a s is the thermodynamic temperature of the lifting gas, R g a s is the specific gas constant of the lifting gas, R H e = 2078.5   J / ( kg K ) for helium, and P g a s is the pressure of the lifting gas.
P g a s = { P a i r V H e V max m g a s R g a s T g a s V b V H e > V max
The differential pressure between the lifting gas and external air, Δ P , can be written as:
Δ P = P g a s P a i r
The balloon envelope thickness (here assuming that the thickness of the skin is uniform and that the thickness is the same everywhere) can be calculated with envelope mass, m e n v , and envelope material, ρ e n v .
d e n v = m e n v A b ρ e n v
The balloon diameter (top view) can be calculated according to the volume of the balloon. For a high-altitude balloon, β d i a is a coefficient representing the effect of the balloon volume and shape change on the equivalent diameter of the balloon [32].
d t o p = β d i a V b 1 / 3

2.3. Dynamic Model

The vertical acceleration of a near-space aerostat is mainly affected by the pressure and temperature of the outside atmosphere. In the vertical direction, the main forces on the aerostat are buoyancy and drag, which will affect the speed change. The following equation demonstrates the influence of these forces on the climbing rate:
a z = d 2 z d t 2 = F z / m t o t
where m t o t is the total mass of the aerostat system and F z is the resultant force on the aerostat in the vertical direction, which can be written as:
F z = B m b g D b | v z _ r e l v b | m t o t a l = m b + m a d d
where m a d d is the air mass displaced by the motion of the balloon, named the virtual mass, which can be calculated using the virtual mass coefficient c a d d . The virtual mass coefficient c a d d can range from 0.25 to 0.5 and is specified as 0.5 here [33]. A precise calculation of the virtual mass can be obtained from references [34,35].
m a d d = c a d d ρ a i r ( z ) V b ( z )
where B is the total buoyancy of an aerostat.
B = V b ( z ) ( ρ a i r ( z ) ρ g a s ) g
V b ( z ) is the aerostat volume.
ρ g a s ( z ) = m g a s V b ( z )
F D is the aerodynamic drag, which can be expressed as:
F D = 1 2 ρ a i r ( z ) v b 2 C d A e f f
A e f f is the effective area that used to calculate the aerodynamic drag.
A e f f = π d t o p 2 / 4
The influence of the balloon shape is mainly considered in the calculation of the aerodynamic drag coefficient, C d .
C d = 4 3 g d t o p v z _ r e l 2 ( 1 M g a s T a i r M a i r T g a s ( 1 + m b m g a s + m t o t a l m g a s a z g ) )

2.4. Thermal Model

The thermal environment of a near-space aerostat is complicated and consists of direct solar radiation, internal and external infrared radiation, scattered radiation, and internal and external convection [36], as depicted in Figure 4.
In this paper, the Earth standard atmosphere was used to analyze the thermal characteristics of the aerostat [37].
T a t m = { 288.15 6.5 h ,   K 0 h 11 km 216.15 ,   K 11 h 20 km 216.15 + ( h 20 ) ,   K 20 h 32 km
The atmosphere dynamic viscosity can be expressed by Sutherland’s formula:
u a = u 0 ( T 0 + C a T a + C a ) ( T a T 0 ) 3 / 2
The atmospheric pressure at any altitude can be calculated using the following formula:
P a = P 0 ( 1 L h T 0 ) M a i r g / ( R L )
The change in the lifting gas temperature in the aerostat is mainly related to the convective heat transfer between the gas and the envelope, as well as the volume change of lifting gas. The lifting gas temperature rate can be obtained through:
d T g a s d t = q i n , g a s M g a s c v + ( γ 1 ) T g a s ( 1 m g a s d m g a s d t 1 V g a s d V g a s d t )
where γ = c p / c v and γ 1 = R g a s / c v . c v is the specific heat at a constant volume of the lifting gas, R g a s is the specific gas constant, and q i n , g a s is the internal thermal convective heat load [38].
The mass change rate can be expressed as:
d m g a s d t = Δ m v a l v e + Δ m d i f f u s i o n
The mass change of the lifting gas mainly includes two parts: discharge through the valve, Δ m v a l v e , and gas diffusion through the envelope, Δ m d i f f u s i o n . The gas diffusion through the envelope can be calculated by the lifting gas diffusion model established in Section 2.1:
Δ m v a l v e = A v a l v e c d i s c h 2 Δ P v a l v e ρ g a s
Δ m d i f f u s i o n = M g a s D r e a l P g a s P a i r ( C i n C o u t ) d e n v A b
where A v a l u e is the outlet area of the valve, c d i s c h is the discharge coefficient, and Δ P v a l v e is the differential pressure across the area interface.
The envelope temperature differential equation can be expressed as:
m e n v c e n v d T e n v d t = q i n ,   e n v
The heat flux terms q i n , e n v in Equation (34) are given as:
q i n ,   e n v = q D + q S + q a l b e d o + q I R + q c o n v
where q D is the absorbed direct sunlight heat. The absorbed direct solar radiation includes the heat absorbed by the outer surface of the envelope and the heat absorbed by the inner surface through the envelope [39]. The effective absorption of the envelope will be improved due to the multiple types of reflection taking place.
q D = α e n v A p r o j I s u n τ a t m ( 1 + τ e n v 1 γ e n v )
where α e n v is the absorption coefficient of the envelope material for solar radiation, A p r o j is the projected area of the balloon, I s u n is the direct solar irradiance, τ a t m is the transmission coefficient of the atmosphere for sunlight, and τ e n v and γ e n v are the transmittance and reflectance of the envelope material, respectively [20].
q S the absorbed scattered radiation and can be expressed as:
q S = α e n v κ S A b I s u n τ a t m ( 1 + τ e n v ( 1 + γ e n v ) )
where κ S is the atmospheric scattering empirical coefficient.
q a l b e d o is the ground albedo radiation, and its intensity is mainly affected by the direct solar radiation intensity and the average albedo of the ground.
q a l b e d o = α e n v A b V F I a l b e d o ( 1 + τ e n v ( 1 + γ e n v ) )
where I a l b e d o = ε G I s u n sin ( α e l e ) , ε G is the ground albedo, α e l e is the sun elevation angle, and V F is the angle coefficient between the balloon surface and the Earth’s surface, which is related to the flight altitude [40].
q I R is the absorbed infrared radiation heat, which mainly includes ground infrared radiation, q I R , E ; infrared radiation from the sky, q I R , s k y ; and infrared radiation self-glow from the interior, q I R , e n v .
q I R = q I R , E + q I R , s k y + q I R , e n v
q I R , E = α I R A s u r f I I R , E V F ( 1 + τ I R / ( 1 r I R ) ) q I R , s k y = α I R A s u r f I I R , s k y ( 1 V F ) ( 1 + τ I R / ( 1 r I R ) ) q I R , e n v = α e n v ε A s u r f T e n v 4 ( 1 + α I R / ( 1 r I R ) + τ I R / ( 1 r I R ) )
I I R , s k y = ε g σ T s k y 4 τ a t m _ I R , and T s k y is the effective temperature of the sky [41].
q c o n v is the convective heat load on the envelope.
q c o n v = h e x A b ( T e n v T a t m ) + h i n A b ( T e n v T g a s )
The external thermal convection coefficient (which is mainly composed of natural convection, h f r e e - e x , and the forced convection heat transfer coefficient, h f o r c e d - e x ) is given as [42]:
h e x = ( h f r e e - e x 3 + h f o r c e d - e x 3 ) 1 / 3

3. Model Validation

3.1. Verification of the Dynamic Model

Based on the thermal and dynamic models established in this paper, a computer program was developed. The high-altitude experimental data obtained by Yang et al. [33] were used to verify the validity and accuracy of the dynamic model developed in this study. The same balloon parameters, launch times, and launch sites were used in our comparative analysis. These critical parameters are listed in Table 1. During ascent, the differential pressure between the lifting gas and external air was approximately equal to 0 until the maximum design altitude was reached. By comparing the results of the numerical simulation and the experimental data (as shown in Figure 5), it can be seen that the maximum relative error of the flight altitude was less than 5%. There were some differences in flight altitude during ascent, mainly due to the influence of the aerodynamic drag coefficient on the shape change. The variation in balloon flight altitude with the flight time distribution remained almost identical. Hence, the dynamic model developed in this paper can be applied to indicate flight status with reasonable accuracy.
After reaching the design altitude, the pressure and temperature of the internal lifting gas of the aerostat rose rapidly. Then, there were some valve-switching operations that have not been described in the literature; these operations affected the accuracy of temperature prediction based on Equation (30). As can be seen in Figure 6, the prediction result and reference values corresponded with deviations below 9%, which means that the present thermal model can be used to predict the temperature characteristics of aerostats.

3.2. Verification of Lifting Gas Diffusion Model

In order to understand the mechanism of the helium leakage of aerostat envelope materials, Wu [43] carried out theoretical and experimental studies. The results of these studies were used to verify the accuracy of our mass transfer model. The design parameters used for analyzing the envelope diffusion coefficient are listed in Table 2. During the flight, the temperature of the balloon envelope generally varied from 216 to 336 K. Therefore, in [43], the diffusion coefficient of an envelope under a range of different envelope temperatures was analyzed. As shown in Figure 7, the diffusion coefficients of envelopes given in the literature and predicted in this paper increased with increases in envelope temperature. In addition, the deviations between the comparison data and the predicted results were less than 6%, indicating that the mass transfer model established in this paper can be used to estimate the lifting gas leakage and flight endurance in the preliminary design of an aerostat.

4. Discussion

4.1. Simulation Conditions

The theoretical model established in this paper was used to predict the gas diffusion characteristics and flight performance of a near-space super-pressure balloon. The main design parameters of the balloon are listed in Table 3.

4.2. Effects of ε e n v / τ s s

Based on the theory established in this paper, it can be stated that the mass of the lifting gas inside a near-space aerostat directly affects the volume and pressure of the lifting gas. Additionally, the total buoyancy of a near-space aerostat varies with the volume of the aerostat at a given altitude. Furthermore, the atmospheric pressure decreases with increases in the altitude, as does the density of the atmosphere. Based on this analysis, it can be summarized that a change in the mass of the lifting gas will affect the flight altitude of an aerostat. In order to meet the needs of long-term monitoring and long-distance communication, the near-space aerostat—a brand-new concept intended to meet the requirements of long-endurance station-keeping performance—was developed. This means that the flight altitude of an aerostat needs to be guaranteed above a certain limit. Therefore, the effects of the air tightness parameters of the envelope material and the ratio of porosity to tortuosity on the mass of lifting gas inside a near-space aerostat should be studied in detail. For this purpose, five simulations were conducted to study the ratio of porosity to tortuosity ( ε e n v / τ s s = 0.001, 0.002, 0.004, 0.008, and 0.012).
Figure 8 presents the variations in the mass of lifting gas inside a near-space aerostat with the ε e n v / τ s s  and the ratio of porosity to tortuosity at different flight times. In order to meet the needs of long-term monitoring and long-distance communication, a minimum flight altitude of 15 km was used in this study. In order to achieve station-keeping at this altitude, a sufficient level of lifting gas inside the near-space aerostat had to be maintained. It was found that 16 kg of lifting gas is required for an aerostat to fly at the altitude of 15 km. Under the same flight endurance, the mass of lifting gas inside a near-space aerostat was found to increase with decreases in the ratio of porosity to tortuosity when all aerostats are flying above the lowest altitude. The calculations showed that the amount of lifting gas diffusion taking place increases as the ratio of porosity to tortuosity increases. Additionally, the airtightness of the envelope material tends to worsen over time.
Furthermore, it is obvious that flight endurance will increase with decreases in ε e n v / τ s s . The flight endurance corresponding to different ε e n v / τ s s values was found to be 31.8, 43.9, 76.8, 129.2, and 216.3 days. It can be concluded that flight endurance at a higher ratio of porosity to tortuosity, ε e n v / τ s s , dramatically decreases, whereas it is fairly stable for lower ratios of ε e n v / τ s s . This indicates that an optimal ratio of porosity to tortuosity may exist for the selection of envelope materials.
The effects of ε e n v / τ s s on the flight altitude of near-space aerostats are shown in Figure 9. It was found that when the ratio of porosity to tortuosity decreases, the flight altitude increases. Under the same ε e n v / τ s s , the flight altitude of a near-space aerostat decreases with the flight time when all aerostats are flying above the lowest altitude. Additionally, the rate of height change gradually increases, especially at smaller ε e n v / τ s s .
In order to evaluate the effects of ε e n v / τ s s on the diffusion coefficient of an envelope, a series of values for the ratio of porosity to tortuosity were considered. The variation in the diffusion coefficient with ε e n v / τ s s is shown in Figure 10. The results showed that with increases in the flight endurance, the diffusion coefficient decreases. The diffusion coefficient was found to decrease with ε e n v / τ s s due to an increase in the molecular diffusivity. If ε e n v / τ s s becomes larger, the diffusion coefficient decreases faster.
Furthermore, the ratio of ε e n v / τ s s was found to have a significant influence on the envelope and gas temperature, as well as the gas pressure, as shown in Figure 11. With the increase in the flight endurance, the maximum temperatures of the envelope and lifting gas per day were found to first rapidly and then slowly increase before finally decreasing. These results showed that the maximum temperature of the envelope and lifting gas per day are mainly affected by the flight date. The initial flight date was set to be 1 January. With the increase in the flight endurance, the heat caused by direct sunlight was found to gradually increase until the summer solstice. On the same flight date, the higher the ε e n v / τ s s is, the lower the maximum temperatures of the envelope and lifting gas were shown to be, although the difference was small, as shown in Figure 11a,b. This temperature difference is mainly caused by the leakage of lifting gas. The maximum gas pressure per day was found to rapidly increase with the increase in flight endurance, as shown in Figure 11c, because of the decrease in the flight altitude. As shown in Figure 11d, the maximum gas pressure difference (PgasPair) per day was shown to first decrease and then increase with the increase in flight endurance. The main factor influencing the descending section was found to be the leakage of lifting gas, which is caused by the initial high diffusion coefficient of the envelope based on Equation (3). The main factor influencing the rising section was found to be the increase in the lifting gas temperature.

4.3. Effect of Envelope Radiation Properties

As shown in Figure 12, the effects of the envelope temperature on the lifting gas diffusion rate, envelope thickness, and diffusion coefficient of the near-space aerostat were studied. Under normal conditions, the lowest temperature of a near-space aerostat envelope would be about 210 K, while the highest temperature at noon would be 310 K. Therefore, the lifting gas diffusion rate, envelope thickness, and diffusion coefficient in this temperature variation range were analyzed in this paper. It was found that when envelope temperature rose from 210 to 310 K, the lifting gas diffusion rate increased from 1.33 to 2.32 g/s and the diffusion coefficient increased from 2.75 × 10−10 to 4.79 × 10−10 m/s−2. The envelope thickness of the near-space aerostat decreased with increases in the envelope temperature. The reason for this is that the effective diffusion coefficient, which was calculated considering the Knudsen and molecular diffusions, was found to be positively related to the envelope temperature. This result implies that the envelope temperature can affect the lifting gas diffusion rate by changing the effective diffusion coefficient.
Figure 13 illustrates the temperatures of the lifting gas and envelope and the lifting gas diffusion rate at the summer and winter solstices. It can be seen that there was an obvious peak value of temperature change in the day, which is consistent with the theoretical expectation. The temperatures of the envelope could achieve their highest values, 273.3 and 249.8 K at noon during the summer and winter solstices, respectively. The highest temperatures of the lifting gas were found to be 244.2 and 233.3 K, which were lower than those of the envelope. Furthermore, it is obvious that the temperature differences of the lifting gas and inner air presented the same expressional tendencies. The maximum lifting gas diffusion rate on the day of the summer solstice is obviously larger than that observed on the day of the winter solstice. This result implies that the mass of lifting gas diffused on the day of the summer solstice will be obviously larger than that on the day of the winter solstice.
Examples of how the flight altitude of the near-space aerostat and diffusion coefficient were shown to be influenced by the envelope absorptivity are shown in Figure 14 and Figure 15. Envelope absorptivities of 0.02, 0.05, 0.1, 0.2, and 0.4 were used, as these represent the absorptivity range of most envelope materials. Under the same level of flight endurance, the flight altitude of the near-space aerostat was shown to increases with decreases in the envelope absorptivity when the aerostat was flying above the lowest altitude. It can be seen in Figure 15 that over the whole flight period, the diffusion coefficient first slowly and then sharply declined as the flight time increased. The results showed that the trends of the flight altitude of the simulated and measured diffusion coefficients were consistent. These results indicate that a higher envelope absorptivity will result in a higher temperature of the lifting gas and envelope, which will consequently increase the mass of lifting gas diffused. Based on Equation (8), the diffusion coefficient is a function of T e n v 3 / 2 / P g a s . As can be seen from Figure 16, the maximum skin temperature and maximum gas pressure per day were found to gradually increase along with the flight endurance, but the rate of change of rising speed was different, leading to a nonlinear downward trend.
The effects of envelope absorptivity on the envelope and gas temperature, as well as the gas pressure, were studied in order to analyze the mechanism of the effect of absorptivity on the diffusion properties, as shown in Figure 16. With the increase in the flight endurance, the maximum temperatures of the envelope and lifting gas per day firstly increased and then decreased, as shown in Figure 16a,b. On the same flight date, the envelope temperature with a higher absorptivity was significantly higher than that with a lower absorptivity. The maximum gas pressure and maximum gas pressure difference per day increased with the increase in envelope absorptivity, as shown in Figure 16c,d.
As shown in Figure 17, five envelope emissivities were considered here to investigate their impact on the flight altitude of a near-space aerostat. Several common envelope materials were considered for this parametric study. It can be seen that the flight altitude of the aerostat decreased as the flight time increased. The flight endurances of the near-space aerostat under these situations remained fairly steady for 190 days. The results of this research demonstrate that the envelope emissivity has some effect on the flight altitude. Figure 18 presents the effects of the envelope emissivity on the diffusion coefficient. It can be easily seen that the diffusion coefficient was reduced by almost 50% as the flight time increased. The effects of the envelope emissivity on the envelope and gas temperature, as well as the gas pressure, were studied in order to analyze the mechanism of the effect of the envelope emissivity on the diffusion properties, as shown in Figure 19. With the increase in the flight endurance, the maximum temperatures of the envelope and lifting gas per day firstly increased and then decreased, as shown in Figure 19a,b. On the same flight date, the temperature of the envelope with a lower emissivity was significantly higher than that of the envelope with a higher emissivity. The maximum gas pressure and maximum gas pressure difference per day decreased with increases in the envelope emissivity, as shown in Figure 19c,d.

5. Conclusions

Based on the lifting gas diffusion model and dynamic model with thermal effect established in this paper, the lifting gas diffusion behavior and the effects of the envelope properties on the flight performance of the aerostat were numerically investigated and validated. The main results were as follows:
(1)
Based on the verification of results, it was found that the lifting gas diffusion model proposed in this paper, which considers the thermal effect for a near-space aerostat during a long-endurance flight, can be utilized to study lifting gas permeability and flight performance.
(2)
The ratio of porosity to tortuosity was found to have a significant influence on the gas diffusion coefficient, directly leading to a sharp decline in flight endurance with increases in the ratio of porosity to tortuosity. In the preliminary design of an aerostat, it is helpful to choose an envelope material with an optimal ratio of porosity to tortuosity in order to improve the aerostat’s flight performance.
(3)
During high-altitude flight, the lifting gas diffusion rate and diffusion coefficient are very sensitive to changes in envelope temperature. Compared to the envelope infrared emissivity, the envelope absorptivity was found to have a stronger influence on the lifting gas diffusion and the thermal performance of near-space aerostats. A higher envelope absorptivity would result in higher temperatures of the lifting gas and envelope, which would consequently increase the mass of lifting gas diffused.

Author Contributions

Conceptualization, J.L. (Jun Li) and L.L.; methodology, Z.C. and L.L.; software, J.L. (Jun Liao); validation, J.L. (Jun Liao), J.L. (Jun Li) and L.L.; investigation, S.L.; data curation, L.L.; writing—original draft preparation, L.L. and Z.C.; writing—review and editing, J.L. (Jun Liao) and J.L. (Jun Li); visualization, J.L. (Jun Li); supervision, S.L. All authors have read and agreed to the published version of the manuscript.

Funding

This work was supported by the Key R&D Projects of Hunan Province (2021GK2011) and the Natural Science Foundation of Hunan Province No. 2019JJ50773, as well as National Key Research and Development Program of China (2016YFB0500801). This research was also supported by the Innovation-Driven Project of Central South University (No. 2018CX024).

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Bellemare, M.G.; Candido, S.; Castro, P.S.; Gong, J.; Machado, M.C.; Moitra, S.; Ponda, S.S.; Wang, Z. Autonomous navigation of stratospheric balloons using reinforcement learning. Nature 2020, 588, 77–82. [Google Scholar] [CrossRef] [PubMed]
  2. Gangadhar, A.; Manikandan, M.; Rajaram, D.; Mavris, D. Conceptual design and feasibility study of winged hybrid airship. Aerospace 2022, 9, 8. [Google Scholar] [CrossRef]
  3. Gemignani, M.; Marcuccio, S. Dynamic characterization of a high-altitude balloon during a flight campaign for the detection of ISM radio background in the stratosphere. Aerospace 2021, 8, 21. [Google Scholar] [CrossRef]
  4. Du, H.; Lv, M.; Li, J.; Zhu, W.; Zhang, L.; Wu, Y. Station-keeping performance analysis for high altitude balloon with altitude control system. Aerosp. Sci. Technol. 2019, 92, 644–652. [Google Scholar] [CrossRef]
  5. Ramesh, S.S.; Ma, J.; Lim, K.M.; Lee, H.P.; Khoo, B.C. Numerical evaluation of station-keeping strategies for stratospheric balloons. Aerosp. Sci. Technol. 2018, 80, 288–300. [Google Scholar] [CrossRef]
  6. van Wynsberghe, E.; Turak, A. Station-keeping of a high-altitude balloon with electric propulsion and wireless power transmission: A concept study. Acta Astronaut. 2016, 128, 616–627. [Google Scholar] [CrossRef]
  7. Yang, Y.; Wu, J.; Zheng, W. Station-keeping control for a stratospheric airship platform via fuzzy adaptive backstepping approach. Adv. Space Res. 2013, 51, 1157–1167. [Google Scholar] [CrossRef]
  8. Du, H.; Li, J.; Zhu, W.; Qu, Z.; Zhang, L.; Lv, M. Flight performance simulation and station-keeping endurance analysis for stratospheric super-pressure balloon in real wind field. Aerosp. Sci. Technol. 2019, 86, 1–10. [Google Scholar] [CrossRef]
  9. Hall, J.L.; Yavrouian, A. Pinhole effects on Venus superpressure balloon lifetime. In Proceedings of the AIAA Balloon Systems (BAL) Conference, Daytona Beach, FL, USA, 25–28 March 2013. [Google Scholar]
  10. Yin, B.; Xu, S.; Yang, S.; Dong, F. Influence of microelliptical groove gas diffusion layer (GDL) on transport behavior of proton exchange membrane fuel cell (PEMFC). Int. J. Heat Mass Transf. 2021, 180, 121793. [Google Scholar] [CrossRef]
  11. Shi, T.; Chen, W.; Gao, C.; Hu, J.; Zhao, B.; Wang, M. Biaxial strength determination of woven fabric composite for airship structural envelope based on novel specimens. Compos. Struct. 2018, 184, 1126–1136. [Google Scholar] [CrossRef]
  12. Kang, W.; Suh, Y.; Lee, I. Mechanical property characterization of film-fabric laminate for stratospheric airship envelope. Compos. Struct. 2006, 75, 151–155. [Google Scholar] [CrossRef]
  13. García-Salaberri, P.A.; Hwang, G.; Vera, M.; Weber, A.Z.; Gostickd, J.T. Effective diffusivity in partially-saturated carbon-fiber gas diffusion layers: Effect of through-plane saturation distribution. Int. J. Heat Mass Transf. 2015, 86, 319–333. [Google Scholar] [CrossRef] [Green Version]
  14. Kumazawa, H.; Aoki, T.; Susuki, I. Influence of stacking sequence on leakage characteristics through CFRP composite laminates. Compos. Sci. Technol. 2006, 66, 2107–2115. [Google Scholar] [CrossRef]
  15. Yokozeki, T.; Ogasawara, T.; Ishikawa, T. Evaluation of gas leakage through composite laminates with multilayer matrix cracks: Cracking angle effects. Compos. Sci. Technol. 2006, 66, 2815–2824. [Google Scholar] [CrossRef]
  16. Thornton, A.W.; Hilder, T.; Hill, A.J.; Hill, J.M. Predicting gas diffusion regime within pores of different size, shape and composition. J. Membr. Sci. 2009, 336, 101–108. [Google Scholar] [CrossRef]
  17. Yao, X.F.; Lei, Y.M.; Xiong, C.; Wang, X.Q.; Wang, Y.Q. Experimental study of helium leakage parameters in flexible composite. J. Appl. Polym. Sci. 2010, 116, 3562–3568. [Google Scholar] [CrossRef]
  18. Yin, Y.; Qu, Z.G.; Zhang, J.F. Multiple diffusion mechanisms of shale gas in nanoporous organic matter predicted by the local diffusivity lattice Boltzmann model. Int. J. Heat Mass Transf. 2019, 143, 118571. [Google Scholar] [CrossRef]
  19. Kayhan, Ö.; Hastaoglu, M.A. Modeling of stratospheric balloon using transport phenomena and gas compress–release system. J. Thermophys. Heat Transf. 2014, 28, 534–541. [Google Scholar] [CrossRef]
  20. Zhu, W.; Xu, Y.; Du, H.; Li, J. Thermal performance of high-altitude solar powered scientific balloon. Renew. Energy 2019, 135, 1078–1096. [Google Scholar] [CrossRef]
  21. Wu, J.; Fang, X.; Wang, Z.; Hou, Z.; Ma, Z.; Zhang, H.; Dai, Q.; Xu, Y. Thermal modeling of stratospheric airships. Prog. Aerosp. Sci. 2015, 75, 26–37. [Google Scholar] [CrossRef]
  22. Xiong, J.; Bai, J.B.; Chen, L. Simplified analytical model for predicting the temperature of balloon on high-altitude. Int. J. Therm. Sci. 2014, 76, 82–89. [Google Scholar] [CrossRef]
  23. Kayhan, Ö.; Hastaoglu, M.A. Control of high altitude telecommunication balloons via transport phenomena, material and fuell cell. In Proceedings of the 6th International Conference on Recent Advances in Space Technologies IEEE, Istanbul, Turkey, 12–14 June 2013. [Google Scholar]
  24. Li, Y.; Kalantari-Dahaghi, A.; Zolfaghari, A.; Dong, P.; Negahban, S.; Zhou, D. A new model for the transport of gaseous hydrocarbon in shale nanopores coupling real gas effect, adsorption, and multiphase pore fluid occupancies. Int. J. Heat Mass Transf. 2020, 148, 119026. [Google Scholar] [CrossRef]
  25. Yuan, J.; Sundén, B. On mechanisms and models of multi-component gas diffusion in porous structures of fuel cell electrodes. Int. J. Heat Mass Transf. 2014, 69, 358–374. [Google Scholar] [CrossRef]
  26. Cussler, E.L. Diffusion: Mass Transfer in Fluid Systems; Cambridge University Press: Cambridge, UK, 2009; pp. 191–206. [Google Scholar]
  27. Pan, L.; Xu, K. Two-stage fourth-order gas-kinetic scheme for three-dimensional Euler and Navier-Stokes solutions. Int. J. Comput. Fluid Dyn. 2018, 10, 395–411. [Google Scholar] [CrossRef] [Green Version]
  28. Hastaoglu, M.A. Transient modelling of a packed tower: Mass and heat transfer with reaction. Fuel 1995, 74, 1624–1631. [Google Scholar] [CrossRef]
  29. Sadagopan, A.; Camci, C. Viscous flow and performance issues in a 6:1 supersonic mixed-flow compressor with a tandem diffuser. Aerosp. Sci. Technol. 2019, 88, 9–21. [Google Scholar] [CrossRef]
  30. Cuenya, B.R. Synthesis and catalytic properties of metal nanoparticles: Size, shape, support, composition, and oxidation state effects. Thin Solid Films 2010, 518, 3127–3150. [Google Scholar] [CrossRef]
  31. Müller, D.; Warneke, T.; Rixen, T.; Müller, M.; Mujahid, A.; Bange, H.W.; Notholt, J. Fate of peat-derived carbon and associated CO2 and CO emissions from two Southeast Asian estuaries. Biogeosci. Discuss. 2016, 12, 8299–8340. [Google Scholar]
  32. Farley, R.E. BalloonAscent-3-D simulation tool for the ascent and float of high-altitude balloons. In Proceedings of the AIAA 5th Aviation, Technology, Integration, and Operations Conference, Arlington, VA, USA, 26–28 September 2005. [Google Scholar]
  33. Yang, X.; Zhang, W.; Hou, Z. Improved Thermal and Vertical Trajectory Model for Performance Prediction of Stratospheric Balloons. J. Aerosp. Eng. 2015, 28, 04014075. [Google Scholar] [CrossRef]
  34. Korotkin, A.I. Added Masses of Ship Structures; Springer Science & Business Media: Berlin, Germany, 2008; pp. 1–111. [Google Scholar]
  35. Said, C.; Naoufel, A. Estimation of the virtual masses of a large unconventional airship based on purely analytical method to aid in the preliminary design. Aircr. Eng. Aerosp. Technol. 2022, 94, 531–540. [Google Scholar]
  36. Zhang, Y.; Liu, D. Influences of initial launch conditions on flight performance of high altitude balloon ascending process. Adv. Space Res. 2015, 56, 605–618. [Google Scholar] [CrossRef]
  37. Saleh, S.; He, W. New design simulation for a high-altitude dual-balloon system to extend lifetime and improve floating performance. Chin. J. Aeronaut. 2018, 31, 247–256. [Google Scholar] [CrossRef]
  38. Liu, Q.; Wu, Z.; Zhu, M.; Xu, W.Q. A comprehensive numerical model investigating the thermal-dynamic performance of scientific balloon. Adv. Space Res. 2014, 53, 325–338. [Google Scholar] [CrossRef]
  39. Liu, Y.; Xu, Z.; Du, H.; Lv, M. Multidisciplinary optimization of thermal insulation layer for stratospheric airship with a solar array. Aerospace 2022, 9, 83. [Google Scholar] [CrossRef]
  40. Saleh, S.; He, W. Ascending performance analysis for high altitude zero pressure balloon. Adv. Space Res. 2017, 59, 2158–2172. [Google Scholar] [CrossRef]
  41. Dai, Q.; Fang, X.; Zhao, Y.; Xing, D. An empirical model for estimating the atmospheric transmittance of upward infrared radiation at different altitudes. Adv. Space Res. 2016, 58, 2453–2459. [Google Scholar] [CrossRef]
  42. Bergman, T.L.; Incropera, F.P.; Dewitt, D.P.; Lavine, A.S. Fundamentals of Heat and Mass Transfer; John Wiley & Sons: New York, NY, USA, 2011; pp. 378–419. [Google Scholar]
  43. Qing, W. Theoretical and Experimental Study of Helium Leakage Mechanism of Aerostat Envelope Materials. Master’s Thesis, Tsinghua University, Beijing, China, 2010. [Google Scholar]
Figure 1. (a) A 5.5 m diameter prototype balloon undergoing testing; (b) 35-day buoyancy test data [9].
Figure 1. (a) A 5.5 m diameter prototype balloon undergoing testing; (b) 35-day buoyancy test data [9].
Aerospace 09 00328 g001
Figure 2. (a) Photograph of envelope; (b) cross-section of the aerostat envelope [12].
Figure 2. (a) Photograph of envelope; (b) cross-section of the aerostat envelope [12].
Aerospace 09 00328 g002
Figure 3. The mass transfer mechanism of lifting gas passing through an envelope [23].
Figure 3. The mass transfer mechanism of lifting gas passing through an envelope [23].
Aerospace 09 00328 g003
Figure 4. Thermal balance of a near-space aerostat.
Figure 4. Thermal balance of a near-space aerostat.
Aerospace 09 00328 g004
Figure 5. Comparison between the predicted data and the experimental data (flight altitude).
Figure 5. Comparison between the predicted data and the experimental data (flight altitude).
Aerospace 09 00328 g005
Figure 6. Comparison between the predicted data and the experimental data (lifting gas temperature).
Figure 6. Comparison between the predicted data and the experimental data (lifting gas temperature).
Aerospace 09 00328 g006
Figure 7. Comparisons of the diffusion coefficient of the envelope [43].
Figure 7. Comparisons of the diffusion coefficient of the envelope [43].
Aerospace 09 00328 g007
Figure 8. Effects of ε e n v / τ s s on the mass of lifting gas inside a near-space aerostat.
Figure 8. Effects of ε e n v / τ s s on the mass of lifting gas inside a near-space aerostat.
Aerospace 09 00328 g008
Figure 9. Effects of ε e n v / τ s s on the flight altitude of near-space aerostats.
Figure 9. Effects of ε e n v / τ s s on the flight altitude of near-space aerostats.
Aerospace 09 00328 g009
Figure 10. Effects of ε e n v / τ s s on the diffusion coefficient of the envelope.
Figure 10. Effects of ε e n v / τ s s on the diffusion coefficient of the envelope.
Aerospace 09 00328 g010
Figure 11. Effects of ε e n v / τ s s on the (a) maximum skin temperature per day, (b) maximum gas temperature per day, (c) maximum gas pressure per day, and (d) maximum gas pressure difference per day.
Figure 11. Effects of ε e n v / τ s s on the (a) maximum skin temperature per day, (b) maximum gas temperature per day, (c) maximum gas pressure per day, and (d) maximum gas pressure difference per day.
Aerospace 09 00328 g011aAerospace 09 00328 g011b
Figure 12. The lifting gas diffusion rate, envelope thickness, and diffusion coefficient.
Figure 12. The lifting gas diffusion rate, envelope thickness, and diffusion coefficient.
Aerospace 09 00328 g012
Figure 13. The temperatures of the lifting gas and envelope and the lifting gas diffusion rate at the (a,b).
Figure 13. The temperatures of the lifting gas and envelope and the lifting gas diffusion rate at the (a,b).
Aerospace 09 00328 g013
Figure 14. Effects of envelope absorptivity on the flight altitude.
Figure 14. Effects of envelope absorptivity on the flight altitude.
Aerospace 09 00328 g014
Figure 15. Effects of envelope absorptivity on the diffusion coefficient.
Figure 15. Effects of envelope absorptivity on the diffusion coefficient.
Aerospace 09 00328 g015
Figure 16. Effects of envelope absorptivity on the (a) maximum skin temperature per day, (b) maximum gas temperature per day, (c) maximum gas pressure per day, and (d) maximum gas pressure difference per day.
Figure 16. Effects of envelope absorptivity on the (a) maximum skin temperature per day, (b) maximum gas temperature per day, (c) maximum gas pressure per day, and (d) maximum gas pressure difference per day.
Aerospace 09 00328 g016aAerospace 09 00328 g016b
Figure 17. Effects of envelope emissivity on flight altitude.
Figure 17. Effects of envelope emissivity on flight altitude.
Aerospace 09 00328 g017
Figure 18. Effects of envelope emissivity on diffusion coefficient.
Figure 18. Effects of envelope emissivity on diffusion coefficient.
Aerospace 09 00328 g018
Figure 19. Effects of envelope emissivity on the (a) maximum skin temperature per day, (b) maximum gas temperature per day, (c) maximum gas pressure per day, and (d) maximum gas pressure difference per day.
Figure 19. Effects of envelope emissivity on the (a) maximum skin temperature per day, (b) maximum gas temperature per day, (c) maximum gas pressure per day, and (d) maximum gas pressure difference per day.
Aerospace 09 00328 g019aAerospace 09 00328 g019b
Table 1. Design parameters of the near-space aerostat used for comparison [33].
Table 1. Design parameters of the near-space aerostat used for comparison [33].
ParametersValue
Design altitude (km)20
Total mass (kg)5700
Helium gas mass (kg)900
Envelope mass (kg)1200
Maximum volume (m3)65,000
Absorption coefficient, α e n v 0.3
Transmission coefficient, τ e n v 0.5
Launch time1 July at 07:00
Launch site110° E, 30° N
Table 2. Design parameters used for analyzing an envelope diffusion coefficient.
Table 2. Design parameters used for analyzing an envelope diffusion coefficient.
ParametersValue
Envelope thickness (m)2.7 × 10−4
Pressures of the lifting gas (mPa)0.1
Porosity of the envelope material0.2%
Tortuosity (kg/(m s2))2
Collision diameters of lifting gas2.551
Collision diameters of ambient air3.711
Pore radius (m)0.2 × 10−6
Table 3. Main parameters of the aerostat used for the simulation.
Table 3. Main parameters of the aerostat used for the simulation.
ParametersValue
Design altitude (km)20
Failure altitude (km)15
Total mass (kg)145
Initial helium gas mass (kg)20
Payload mass (kg)67.2
Envelope mass (kg)57.7
Maximum volume (m3)1625
Maximum overpressure (Pa)600
Launch date1 January
Launch siteChangsha, Hunan
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Li, J.; Ling, L.; Liao, J.; Chen, Z.; Luo, S. Effect of Lifting Gas Diffusion on the Station-Keeping Performance of a Near-Space Aerostat. Aerospace 2022, 9, 328. https://doi.org/10.3390/aerospace9060328

AMA Style

Li J, Ling L, Liao J, Chen Z, Luo S. Effect of Lifting Gas Diffusion on the Station-Keeping Performance of a Near-Space Aerostat. Aerospace. 2022; 9(6):328. https://doi.org/10.3390/aerospace9060328

Chicago/Turabian Style

Li, Jun, Linyu Ling, Jun Liao, Zheng Chen, and Shibin Luo. 2022. "Effect of Lifting Gas Diffusion on the Station-Keeping Performance of a Near-Space Aerostat" Aerospace 9, no. 6: 328. https://doi.org/10.3390/aerospace9060328

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop