Next Article in Journal
Dynamic Response of Structurally Reinforced Wing Leading Edge against Soft Impact
Previous Article in Journal
Geostationary Orbital Debris Collision Hazard after a Collision
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Angular Displacement Control for Timoshenko Beam by Optimized Traveling Wave Method

1
School of Mechanical Engineering, Hangzhou Dianzi University, Hangzhou 310018, China
2
School of Mechatronics Engineering, University of Electronic Science and Technology of China, Chengdu 611731, China
3
Aerospace Systems Engineering Research Institute of Shanghai, Shanghai 201108, China
4
College of Electrical Engineering, Zhejiang University, Hangzhou 310027, China
*
Authors to whom correspondence should be addressed.
These authors contributed equally to this work.
Aerospace 2022, 9(5), 259; https://doi.org/10.3390/aerospace9050259
Submission received: 14 March 2022 / Revised: 4 May 2022 / Accepted: 7 May 2022 / Published: 11 May 2022

Abstract

:
The vibration of flexible structures in spacecraft, such as large space deployable reflectors, solar panels and large antenna structure, has a great impact on the normal operation of spacecraft. Accurate vibration control is necessary, and the control of angular displacement is a difficulty of accurate control. In the traditional control method, the mode space control has a good effect on suppressing low-order modes, but there is control overflow. The effect of traveling wave control on low-order modes is worse than the former, but it has the characteristics of broadband control. It can better control high-order modes and reduce control overflow. In view of the advantages and disadvantages of the two control methods, based on Timoshenko beam theory, this paper uses vector mode function to analyze the modal of spacecraft cantilever beam structure, establishes the system dynamic equation, and puts forward an optimized traveling wave control method. As a numerical example, three strategies of independent mode space control, traditional traveling wave control and optimized traveling wave control are used to control the active vibration of beam angle. By comparing the numerical results of the three methods, it can be seen that the optimal control method proposed in this paper not only effectively suppresses the vibration, but also improves the robustness of the system, reflecting good control performance. An innovation of this paper is that the Timoshenko beam model is adopted, which considers the influence of transverse shear deformation and moment of inertia on displacement and improves the accuracy of calculation, which is important for spacecraft accessory structures with high requirements for angle control. Another innovation is that the optimized traveling wave control method is exquisite in mathematical processing and has good results in global and local vibration control, which is not available in other methods.

1. Introduction

Flexible cantilever structures are often used in spacecraft structures, such as large antenna structures, large space deployable reflectors and solar panels. In the space environment, the damping is small, and the damping of the flexible structure itself is also small. When it is excited or disturbed by work, such as attitude adjustment and docking, orbit change and solar wind, if the vibration is not controlled, the vibration will last for a long time, which will affect the normal work of the structure and even reduce the service life of the structures [1,2,3,4,5,6].
At present, Euler–Bernoulli beam theory is mainly used in vibration control of beam structure, while Timoshenko beam theory is seldom used for the control difficulties in mathematics. The Euler–Bernoulli classical beam theory has some limitations in structural dynamic analysis, especially in some composite structures. Because the influence of transverse shear deformation and moment of inertia is considered, the analytical results of Timoshenko beam theory are closer to engineering practice [7,8]. Therefore, the Timoshenko beam theory begins to be applied in structural dynamics analysis. Based on Timoshenko beam theory and elastic wave theory, Carvalho and Zindeluk [9] studied the active control of bending waves in infinite Timoshenko beams. Halkyard and Mace [10] studied the bending vibration feedback adaptive control of beam structures by using wave control method. EL-Khatib et al. [11] used a tuned vibration absorber to study the bending wave suppression in a beam. Hu et al. [12] concerned with the control of flexural waves in a beam using a tuned vibration absorber. Su and Ma [13,14] compared three analysis methods: Laplace transform, ray and normal mode to study the dynamic transient response of cantilever Timoshenko beam under impact force. Cardoso [15] blended the Euler–Bernoulli beam theory with idealized transverse shear flows to study a new beam element for aircraft structural analysis. Xing and Liu [16] studied the dynamic modeling and adaptive boundary control of a three-dimensional Timoshenko beam to realize vibration suppression. Ishaquddin et al. [17] studied the flexure and torsion locking phenomena in out-of-plane deformation of the Timoshenko curved beam element. Endo et al. [18] studied a contact-force control problem for a flexible Timoshenko arm. Mei [19] studied a hybrid approach to active control of bending vibrations in beams based on the advanced Timoshenko theory. Pham et al. [20] developed a novel dynamic model of a variable-length Timoshenko beam attached to a translating base. The stability of the closed-loop system under the proposed boundary control law was analyzed. Eshag et al. [21] studied a global sliding mode boundary control method for the Timoshenko beam reduction of the vibration induced by rotation boundary disturbance, uncertainties and distributed disturbance. By using exponential reaching law, the chattering phenomena is avoided. Fleischmann and Könözsy [22] developed an explicit finite difference numerical method to approximately solve the bending equation of non-uniform fourth-order Euler–Bernoulli beams. The equation has velocity-dependent damping and second-order moments of area, and mass and elastic modulus distribution varying with beam spacing. The method is grid convergent and numerically stable. According to literature studies [9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24], it can be seen that the finite element method has become an important theoretical analysis method because it can deal with complex objects and has many general programs. However, the finite element method is more suitable for low-frequency vibration. For medium- and high-frequency vibration, many elements must be divided to accurately describe the vibration characteristics of the system, which will lead to large numerical errors and a sharp increase in the amount of calculation, and the overflow problem will inevitably be encountered when considering vibration control. In addition, enough grid elements must be divided to describe the dynamic characteristics of the structure, the grid of the element is continuously encrypted, and the accumulated error will increase. High requirements for computer hardware configuration are also needed. The modal space control method is to analyze the vibration of the structure from the perspective of the modal. The essence of modal analysis is coordinate transformation. It transforms the coupled motion equations in physical coordinates into modal coordinates for decoupling; thus, as to solve the modal parameters of the system. The above traditional numerical methods can deal with the response of structural vibration well in the low frequency band. However, there are limitations in the medium- and high-frequency bands. With the increase in analysis frequency, it will face many problems, such as the problem of dense and overlapping structural modes.
In this paper, based on Timoshenko beam theory, the vibration control of the cantilever beam is studied by using the optimal traveling wave control method. First, based on Timoshenko beam theory, the modal analysis of the cantilever beam structure commonly used in spacecraft is carried out by using vector vibration mode function, and the system dynamic equation is established. Then, based on the Timoshenko beam theory and the overall motion of the structure, the modal space control method is used to design the global vibration control of the structure. The traveling wave control is used to control the vibration energy flow in the specified area of the structure. According to the local characteristics of the structure, the wave control method is used to absorb the energy carried by the propagating wave in the structural vibration, and the reflection coefficient and transmission coefficient of the wave in the Timoshenko beam when the control torque is applied are obtained. Finally, combined with the advantages of modal space control method, we optimize the traveling wave control method and design an optimized waveform controller to control the rotation angle of the beam. The control results show that the optimized traveling wave control method is better than the traditional traveling wave control method or mode space control method, it and improves the robustness of the system.

2. Structural Dynamic Characteristics of Timoshenko Beam

In engineering practice, it is assumed that the cross-section size of the beam is small compared with its length, thus neglecting the influence of shear deformation and beam section rotation, which is suitable for most members. However, when the ratio of height to span is high or when the composite members are widely used in structures, the effects of shear deformation and cross-section rotation should be taken into account, which have great influence on the higher frequency and mode shape. At this time, Timoshenko beam theory needs to be used. The cantilever Timoshenko beam structure studied in this paper is shown in Figure 1.
It is assumed that the rotation angle of the cross section produced by the bending moment M is ψ . If there is no shear deformation, the cross section is perpendicular to the elastic axis, and Ψ equals the slope of the elastic axis. When shear deformation is taken into account, the rotation angle generated by shear force is γ. The actual cross section angle is α = w / x ; then, we can obtain:
α = ψ γ
The angle ψ and γ meet the following relationship:
ψ x = M E I γ = Q κ G A
where, E ,   I ,   κ ,   G ,   A respectively represent the elastic modulus, the moment of inertia of the beam section, the shear conversion coefficient, the shear modulus and the section area, and I = A h 2 12 ,   G = E 1 + ν ,   κ = π 2 12 , in which h , ν are respectively the section height and the Poisson’s ratio of the material.
Respectively, ρ ,   q ,   m ¯ denoted the mass density, transverse load and bending moment of the beam. Considering the equilibrium of the beam element, the following equilibrium equations can be obtained.
Q d x + M x d x ρ I 2 ψ t 2 d x + m ¯ d x = 0 Q x d x ρ A 2 w t 2 d x + q d x = 0
Substituting Equation (2) into Equation (3), we can obtain:
D 2 ψ x 2 + C w x C ψ + m ¯ = ρ I 2 w t 2 C 2 w x 2 C ψ x + q = ρ A 2 w t 2
The bending moment and shear force in a beam are expressed as:
M = D ψ x = D ρ G A 2 w t 2 2 w x 2 Q = C w x ψ
where D = E I is the bending stiffness of beams, C = κ G A , G is the shear modulus.
Equation (4) can be written in matrix form as follows:
M ¯ 2 Φ t 2 K ¯ 2 Φ x 2 + C E ¯ Φ = F x , t
where Φ = w ψ is the generalized displacement, w ,   ψ are the deflection of beam and angle of rotation, respectively; M ¯ is the generalized mass; t is the time; F x , t = [ q m ¯ ] ; F x , t is the external disturbance dynamic vector, and the expression of M ¯ ,   K ¯ ,   E ¯ is
M ¯ = ρ A 0 0 ρ I ,   K ¯ = C 0 0 D ,   E ¯ = 0 / x / x 1
In order to analyze the frequency characteristics of the beam and consider the free vibration state of the beam, the following equations can be obtained by decoupling the displacement w and the rotation angle ψ in Equation (4):
D 4 w x 4 + ρ A 2 w t 2 ρ I 4 w x 2 t 2 ρ A D C 4 w x 2 t 2 + ρ 2 A I C 4 w t 4 = 0
Equation (7) above shows two degrees of freedom of the Timoshenko beam: the free vibration characteristics w of deflection and rotation angle ψ are exactly the same, that is, the modes of corresponding order, both of which have the same frequency ω and wave number k . In Equation (7), the first and second items denote the basic conditions of vibration, the third and fourth items denote the effect of the cross section moment of inertia and shear deformation, respectively, and the last item denotes the coupling effect of moment of inertia and shear deformation.

3. The Simulation Results and Discussions in the Deorbiting Process

For flexible structures, the low frequency modes are dense; thus, it is difficult to design the controller directly by physical coordinates. In the modal space, the vibration control of the structural system can be transformed into a small number of modal coordinate vibration controls. The response of the structure can be expressed as the sum of infinite modes:
Φ x , t = i = 1 N φ i x q i t
where φ i x is the ith-order mode function, q i t is the ith-order modal coordinates, and N is number of modal truncation.
By deriving Equation (4) from time variables and space variables, the following equation can be obtained at the left end of Equation (4) as:
M ¯ 2 Φ t 2 = M ¯ i = 1 N φ i x 2 q i t t 2 K ¯ 2 Φ x 2 C E ¯ Φ = i = 1 N [ K ¯ 2 φ i x x 2 C E ¯ φ i x ] q i t
Substituting Equation (9) into Equation (6), we can obtain:
M ¯ i = 1 N φ i x 2 q i t t 2 i = 1 N [ K ¯ 2 φ i x x 2 C E ¯ φ i x ] q i t = F x , t
where φ i x is the modal vibration function and should satisfy the homogeneous differential equation as follows:
[ K ¯ 2 φ i x x 2 C E ¯ φ i x ] + ω i 2 M ¯ φ i x = 0
Then, the frequency characteristics of the system are analyzed. Assuming Φ = Re [ e i k x ω t 1 1 T ] A B , and substituting into (7) to obtain:
k 4 ρ I D ω 2 + ρ A C ω 2 k 2 + ρ A D ω 2 ρ I C ω 2 1 = 0
where k 0 = ρ A ω 2 / D 1 / 4 is the elastic traveling wave number of classical Euler beam and k is the wave number of the modal vibration function φ x .
When the vibration frequency of the beam is ω ω c , the elastic wave number is k i 2 0 i = 1 , 2 , which indicates that there are two pairs of propagating waves in the structural beam, and the phase velocity is c = ω / k . When the vibration frequency of the beam is ω < ω c , the elastic wave numbers are k 1 2 > 0 and k 2 2 < 0 , which indicate that there are a pair of propagating waves and a pair of attenuation waves in the structural beam. Where ω c = C / ρ I denotes the transition critical frequency of the extended state and the local state. Because the structure vibration can be regarded as the superposition of multiple reflection of the elastic wave mode, the propagation wave can form the whole vibration of the finite region of the structure, while the attenuation wave forms the localized vibration in the finite area of the structure. Thus, in the beam, a main vibration mode function is determined when a set of wave numbers k 1 and k 2 corresponding to the natural frequencies are determined.
φ i x = w i ψ i = a 1 b 1 cos k 1 x + a 2 b 2 sin k 1 x + a 3 b 3 cos k 2 x + a 4 b 4 sin k 2 x
To study the cantilever beam, use the modal coordinate equation of the beam.
q ¨ i t + ω i 2 q i t = f i t ,   i = 1 , 2 , N
where q t = [ q 1 t , q 2 t , , q N t ] T , f i t = 1 m i 0 l φ i T F x , t d x is the external disturbance force.
The essence of independent modal control is to reconfigure the poles of the vibration system by state feedback; thus, the state space description of the system is established first. Assuming the modal control force is u i t = 1 m i 0 l φ i T U x , t d x , for the vibration system:
q ¨ i t + ω i 2 q i t = f i t + u i t ,   i = 1 , 2 , N
Considering the control of the pth-order mode, and introducing the state vector X t = [ X C t X R t ] , where X C = [ q T t , q ˙ T t ] 2 p × 1 T , the controlled partial state equation of the system is expressed as follows:
X ˙ C t = A C X C t + B C u t + D C f C t
where
A C = 0 I ω 2 0 2 p × 2 p ,   B C = D C = 0 I 2 p × p ,   ω 2 = diag [ ω i 2 ] p × p
In Equation (16), the 0 and I are a zero matrix and a unit matrix, respectively; u t , f t are the modal control force and the modal disturbance force, respectively. When the controllability matrix rank [ B   A B ] = 2 p , based on the linear system theory, we know that the state of the system is completely controllable, and the pole can be arranged arbitrarily. Introducing the state feedback, the control force u t is given as follows:
u t = G X C t = g h q q ˙
The closed-loop dynamic equation of the system (15) is as follows:
X ˙ C t = ( A C B C G ) X C ( t ) + D C f C ( t )
According to Equation (18), the characteristic structure of the original vibration system can be changed arbitrarily by adjusting the feedback gain G .
Considering point force control input U x , t = i = 1 p u ˜ i t δ x x i , point force disturbance input, F x , t = i = 1 n f ˜ i t δ x x i in physical coordinates, where p, n are respectively the number of controlled modes and the number of disturbance forces, and the jth-order mode control force u j t and disturbance force f j t are expressed as follows:
u j t = 1 m j i = 1 p 0 l φ j x u ˜ i t δ x x i = 1 m j i = 1 p φ j x i u ˜ i t f j t = 1 m j i = 1 n 0 l φ j x f ˜ i t δ x x i = 1 m j i = 1 n φ j x i f ˜ i t
where the control input force vector is u ˜ = u ˜ x 1 t u ˜ x 2 t , u ˜ x p t T , and the disturbance input force vector is f ˜ = f ˜ x 1 t f ˜ x 2 t f ˜ x n t T . Thus, the transformation relations of the force vectors between the modal coordinates and the physical coordinates are written as follows
u = Ψ c u ˜ , Ψ c = φ 1 x 1 φ 1 x 2 φ 1 x p φ 2 x 1 φ 2 x p φ p x 1 φ p x p p × p , f d = Ψ d f ˜ , Ψ d = φ 1 x 1 φ 1 x 2 φ 1 x n φ 2 x 1 φ 2 x n φ p x 1 φ p x n p × n
There is no corresponding relation between the position coordinates xi of the above two equations, that is, the position of the control force and the disturbance force is not necessarily the same; and the selected position coordinates should at least ensure Ψ c , Ψ d invertible.
Substituting Equation (20) with Equation (15), the state equation of the controlled part can be obtained as follows:
X ˙ C t = A ˜ C X C t + B ˜ C f ˜ t
where
A ˜ C = 0 I ω 2 + g h 2 p × 2 p , B ˜ C = 0 Ψ d C 2 p × n
where g , h are the generalized displacement gain of the modal control and the generalized velocity gain matrix, respectively. It is obvious that the modal structure of the system is reconstructed by state feedback, and the modal damping and stiffness of the system are improved effectively.
The state equation of the part of the uncontrolled mode should be:
X ˙ R t = A ˜ R X R t + B ˜ R f ˜ t
where
A ˜ R = 0 I ω 2 0 2 N p × 2 N p , B ˜ R = 0 Ψ d R 2 N p × n
The deflection w x 0 , t at the position coordinate x 0 is selected as the output of the system, and the following results can be obtained from Equation (8);
w x 0 , t = w C x 0 , t + w R x 0 , t = i = 1 p φ i x 0 q i t + i = p + 1 N φ i x 0 q i t
The final output of the system is:
w x 0 , t = C X
where
C = Ψ 0 C T 0 Ψ 0 R T 0 1 × 2 N Ψ 0 C = φ 1 x 0 φ 2 x 0 φ r x 0 1 × p T Ψ 0 R = φ r x 0 φ r + 1 x 0 φ N x 0 1 × ( N p ) T
Equations (21), (23) and (26) constitute a complete state space description of partially controlled vibration systems. It is clear that the controlled and uncontrolled modes are independent of each other.

4. Rotating Angle Traveling Wave Control of Timoshenko Beam

Vibration in structure is essentially the propagation of elastic wave in structure. An elastic wave can be regarded as the representation of vibration propagation in a continuous medium. When an elastic wave propagates in a bounded structure and various waveforms are superimposed and stable, its external performance is often regarded as a vibration. Structural vibration is a special form of wave expression, which can be regarded as the result of the superposition of traveling waves satisfying certain conditions. Therefore, the vibration of the structure can be regarded as the propagation, reflection and transmission of the elastic disturbance in the structure, and the whole structure shows a wave characteristic. Therefore, the dynamic response and vibration control of a missile structure can be studied from the perspective of a traveling wave. The vibration in the structure can be described by the superposition of wave modes. The active control method of a traveling wave is to control the energy propagation in the structure, that is, to reduce the transmission from one part of the structure to the other, or to absorb the energy carried by the traveling wave. In wave control, the control law is the transfer relation between the input and output of the controller. It can be divided into time domain design method and frequency domain design method. The control force can be a point force or a point moment. The frequency domain design method is used here. In this paper, a wave controller is designed to control the rotation angle of the beam, and the wave control torque is applied when the rotation angle is controlled.
There are two methods to describe vibration: modal mode description and wave description. In essence, the former belongs to standing wave expression, while the latter is traveling wave expression. Considering the free vibration of the Timoshenko beam, the time factor exp i ω t is omitted:
Φ = A 1 exp i k 1 x + A 2 + exp i k 1 x + A 3 exp k 2 x + A 4 + exp k 2 x
In the above equation, + and represent the positive and negative propagation waves, respectively. The modes with spatial factors exp i k 1 x and exp i k 1 x represent the propagating waves carrying energy, while the modes with spatial factors exp i k 2 x and exp i k 2 x represent the local vibrational modes that do not carry energy. The purpose of wave control is to dissipate and absorb the energy in the propagating wave. When there are no discontinuous points in the infinite beam structure, the above elastic waves will propagate to infinity, and the local vibration modes will decay quickly.
Considering the existence of excitation force in beam structure (shear discontinuity point), according to the traveling wave theory, the reflection and transmission of the elastic wave will occur at the discontinuous incidence. Assuming that a sequence of forward propagating waves is incident at x = 0 , resulting in reflected, transmitted and near-field waves, the displacement of the beam at x 0 and x 0 is as follows
φ ( x ) = w ψ = a + b + exp i k 1 x + a b exp i k 1 x + a N b N exp k 2 x φ + ( x ) = w + ψ + = c + d + exp i k 1 x + c N + d N + exp k 2 x
In the feedback wave control, the sensor and actuator are located in a certain area of the structure to control the propagation of elastic wave. In this case, the control force is a discontinuous point. In the frequency domain feedback wave control, the applied wave control moment is taken as
T ¯ ω = H ω Ψ ω
According to the conditions of generalized displacement continuity and generalized force equilibrium, the function of beam satisfies at x = 0
w 0 = w + 0 ψ 0 = ψ + 0 M + 0 M 0 = H ψ + Q + 0 = Q 0
In Equation (28), H is the transfer function of the wave controller, and the symbols and + represent the corresponding mechanical quantities of the beam at x 0 and x 0 , respectively.
According to the expressions of bending and shear forces, Equation (28) can be written as
1 i k 1 b + + 1 1 i k 1 k 2 B = 1 1 i k 1 + H D H D k 2 D + k 1 2 i k 1 3 b + + k 1 2 k 2 2 i k 1 3 k 2 3 B = k 1 2 k 2 2 H ρ J ω 2 D 2 + i k 1 3 H ρ J ω 2 D 2 + k 2 3 D +
where
B = b b N = r 1 r 2 b + ,   D + = d + d N + = t 1 t 2 b +
Denoted as H ¯ = H D k 1 , ρ J ω 2 D = k 0 4 h 2 12 , the following equation can be obtained:
1 + r 1 + r 2 = t 1 + t 2 , i i r 1 + k 2 k 1 r 2 = i + H ¯ t 1 k 2 k 1 H ¯ t 2 1 + r 1 + r 2 = t 1 + t 2 , i i r 1 + k 2 k 1 r 2 = i + H ¯ t 1 k 2 k 1 H ¯ t 2
It is the same as the method of the wave controller designed to control the lateral displacement, denoted as H ¯ ( ω ) = 1 + i ω g . The energy reflected and transmitted by unit incident energy is E g = r 1 2 + t 1 2 . The maximum energy dissipation in discontinuous structure is taken as the performance index of optimal control, and the optimal control law H ¯ ω is determined.
E g = ( 288 k 1 2 k 2 2 + 288 k 2 4 + 24 g h 2 k 0 4 k 1 k 2 ω 288 g k 1 3 k 2 ω + g 2 h 4 k 0 8 ω 2 24 g 2 h 2 k 0 4 k 1 2 ω 2 + 144 g 2 k 1 4 ω 2 + 24 g 2 h 2 k 0 4 k 2 2 ω 2 144 g 2 k 1 2 k 2 2 ω 2 + 144 g 2 k 2 4 ω 2 ) / ( 288 k 1 2 k 2 2 + 288 k 2 4 + 24 g h 2 k 0 4 k 1 k 2 ω 288 g k 1 3 k 2 ω + 24 g h 2 k 0 4 k 2 2 ω + 288 g k 2 4 ω + g 2 h 4 k 0 8 ω 2 24 g 2 h 2 k 0 4 k 1 2 ω 2 + 144 g 2 k 1 4 ω 2 + 24 g 2 h 2 k 0 4 k 2 2 ω 2 144 g 2 k 1 2 k 2 2 ω 2 + 144 g 2 k 2 4 ω 2 )
When E g reaches the minimum, the feedback gain is
g = a b
where
a = 12 2 h 2 k 0 4 k 1 2 k 2 2 + h 2 k 0 4 k 2 4 + 12 k 1 2 k 2 4 + 12 k 2 6 ,   b = g 1 + g 2 g 1 = h 6 k 0 12 ω 2 24 h 4 k 0 8 k 1 2 ω 2 + 144 h 2 k 0 4 k 1 4 ω 2 + 36 h 4 k 0 8 k 2 2 ω 2 432 h 2 k 0 4 k 1 2 k 2 2 ω 2 g 2 = 1728 k 1 4 k 2 2 ω 2 + 432 h 2 k 0 4 k 2 4 ω 2 1728 k 1 2 k 2 4 ω 2 + 1728 k 2 6 ω 2
The corresponding reflection and transmission coefficients of incident waves are expressed as follows, respectively:
r 1 = g h 2 k 0 4 k 2 ω + 12 g k 2 3 ω i / k 1 k 2 i 12 + 12 i k 1 k 2 12 + 12 i k 2 2 g h 2 k 0 4 ω + 12 g k 1 2 ω + 12 g k 1 k 2 ω i 12 g k 2 2 ω t 1 = 12 + 12 i k 1 2 k 2 12 12 i k 2 3 g h 2 k 0 4 k 1 ω + 12 g k 1 3 ω / k 1 k 2 i 12 + 12 i k 1 k 2 12 + 12 i k 2 2 g h 2 k 0 4 ω + 12 g k 1 2 ω + 12 g k 1 k 2 ω i 12 g k 2 2 ω
If the wave control moment is applied at the point x = x w , the tuning PD control becomes:
m w x , t = [ c 1 w x , t + c 2 w ˙ x , t ] δ x x w
At this time, wave control Equation (34) is applied to the original vibration system, and the matrix form of the motion equation of the system is written as follows:
M ¯ w q ¨ + C ¯ w q ˙ + K ¯ w q = f ¯
where f ¯ = [ f 1 f 2 f n ] T , f i t = 1 m i 0 l φ i T F x , t d x , M ¯ w , C ¯ w , K ¯ w are mass matrix, damping matrix and stiffness matrix, respectively, and the expressions of them are as follows:
M ¯ w = I , C ¯ w = c 2 Ψ ¯ w , K ¯ w = ω 2 + c 1 Ψ ¯ w
where
Ψ ¯ w = φ 1 x w φ 1 x w φ 1 x w φ 2 x w φ 1 x w φ N x w φ 2 x w φ 1 x w φ 2 x w φ N x w φ N x w φ 1 x w φ N x w φ N x w N × N
It is important to note that c 1 , c 2 will also be a matrix, not a number, in subsequent programming calculations. For ease of use in optimized control, we can also write Ψ ¯ w in block form:
Ψ ¯ w = Ψ ¯ C C Ψ ¯ C R Ψ ¯ R C Ψ ¯ R R
When there is no wave control force, the mass array M is N × N identity matrix, C is the N × N zero matrix, K is diagonal matrix with the square of natural frequency. However, the wave control moment is coupled with the vibration modes of the uncontrolled original system, and the mode of the wave control system changes as a result.
Introducing the state vector X t = [ q T t : q ˙ T t ] T , Equation (39) is written in the form of a state space:
X ˙ t = A X t + B f ¯
where the coefficient matrix is:
A = 0 I M ¯ w 1 K ¯ w M ¯ w 1 C ¯ w ,   B = 0 M ¯ w 1 Ψ ¯ d ,   Ψ ¯ d = φ 1 x 1 φ 1 x 2 φ 1 x m φ 2 x 1 φ 2 x m φ N x 1 φ N x m N × m

5. Traveling Wave/Modal Optimized Control of Timoshenko Beam Rotation Angle

The optimized control method of the independent mode and traveling wave is used in this paper. First, the former pth-order mode is controlled by independent modal space control, and the partially controlled vibration system is obtained. The modal dynamic equation of the system is as follows:
M ¯ m q ¨ + C ¯ m q ˙ + K ¯ m q = f ¯
where
M ¯ m = I ,   C ¯ m = h 0 0 0 ,   K ¯ m = ω c 2 + g 0 0 ω R 2
Applying wave control force to the system, combined with (35) and (36), the modal dynamics equation of the system is as follows:
M ¯ h q ¨ + C ¯ h q ˙ + K ¯ h q = f ¯
where
M ¯ h = I ,   C ¯ h = h + c 2 Ψ ¯ C C c 2 Ψ ¯ C R c 2 Ψ ¯ R C c 2 Ψ ¯ R R ,   K ¯ h = ω C 2 + g + c 1 Ψ ¯ C C c 1 Ψ ¯ C R c 1 Ψ ¯ R C ω R 2 + c 1 Ψ ¯ R R
Introducing the state vector X ( t ) = [ q T ( t ) : q ˙ T ( t ) ] T , and the equation of the state is:
X ˙ t = A ˜ X t + B ˜ f ¯
where
A = 0 I M h 1 K h M h 1 C h ,   B = 0 M h 1 Ψ d ,   Ψ d = φ 1 x 1 φ 1 x 2 φ 1 x m φ 2 x 1 φ 2 x m φ N x 1 φ N x m N × m

6. Numerical Example and Analysis and Discussion

Using the independent modal space method and optimized control method, the dynamic response of the structural beam subjected to control force is investigated. Taking the characteristic length as the length of the beam l, the following dimensionless quantities: Poisson ratio ν = 0.30 ; high to length ratio h / l = 0.1 ; damping factor before control ζ = 1.0 × 10 4 ; ω i 2 / ω 0 2 = k 0 i L 4 / k 01 L 4 ; k 0 i is the elastic traveling wave number corresponding to the ith-order natural frequency. Table 1 shows the first 10 dimensionless natural frequencies of the Timoshenko beam.
Figure 2, Figure 3, Figure 4, Figure 5, Figure 6 and Figure 7 show the frequency response of the structure before and after the control with three different control methods under different parameters. In Figure 2, Figure 3, Figure 4, Figure 5, Figure 6 and Figure 7, the horizontal coordinates are dimensionless frequency values, while the vertical coordinates are the common logarithmic values of the frequency response. In Figure 2, Figure 3 and Figure 4, the position of disturbance action is x d = 0.15 l . Figure 2 shows the frequency response before and after modal control; the positions of mode control force applied are x m 1 = 0.215 l , x m 2 = 0.525 l , x m 3 = 0.775 l , x m 4 = 1.0 l ; the first four modes are controlled, and the measuring position of the dynamic response is x s = 0.265 l , where the occurrence point of the maximum value of the total deflection of the first 10 modes is. Figure 3 shows the frequency response of the structure before and after the control when the position of the wave control force is x w = 0.40 l . Figure 4 describes the frequency response of the structure before and after the traveling wave/modal-optimized control.
In Figure 5, Figure 6 and Figure 7, the position of disturbance action is x d = 0.10 l . Figure 5 shows the frequency response before and after modal control. The positions of the modal control force applied are x m 1 = 0.215 l , x m 2 = 0.525 l , x m 3 = 0.775 l , x m 4 = 1.0 l , the first four modes are controlled, and the measuring position of dynamic response is x s = 0.295 l , where the occurrence point of the maximum value of the total deflection of the first 10 modes is. Figure 6 shows the frequency response of the structure before and after the control when the position of the wave control force is x w = 0.30 l , and Figure 7 describes the frequency response of the structure before and after the travelling wave/modal-optimized control.
When applying the wave control force, the node of the first 10 mode vibrations should be avoided as much as possible. The frequency responses of the single-use wave control, independent mode space control and the optimized traveling wave control, including the controlled and uncontrolled frequency response, are compared. In the approximation of the optimized control method, the controller is tuned to the optimum at the fifth mode. In the case of the independent modal space control, the first four-order damping factor of the structure is increased to 0.1 by using the pole assignment method. Through the analysis, we can obtain the discussion as follows:
Figure 2 and Figure 5 show that modal control has good control effect on low-order modes of structure, and it has good independence and has little effect on other modes; thus, the rapid change of the uncontrolled modal response still exists.
Figure 3 and Figure 6 show the frequency response of the structure before and after the use of the wave controller. The response of the structure before the control is sharp, but the wave control can be regarded as adding damping to the structure, absorbing the energy in the structure, and the sharp response is weakened. The figure also shows that the modal characteristics of the whole structure have changed after the wave control; that is, the natural vibration frequency has changed. Finally, we can see that the position of the wave controller is different for the control effect of each mode frequency.
Figure 4 and Figure 7 show the frequency response of the structure before and after using wave control and independent mode space control. It reflects the excellent control effect of the optimized control. Because the optimized control combines the characteristics of the former two methods, that is, the wave control can control the response at higher frequencies better, and the independent modal space control can effectively control the first four modes. It makes up for the poor control effect of wave control at low frequency. Therefore, the performance of using one of the above controls alone is improved.

7. Conclusions

(1)
In this paper, the active vibration control of the Timoshenko beam structure is investigated in a more comprehensive way. First, considering the influence of section rotation and shear deformation, the vibration equation of the Timoshenko beam is established, and the modal and wave analysis are employed. The finite dimensional system dynamic equation is obtained by modal expansion. Then, we adopt three different control methods: traditional mode space control method, traditional traveling wave control method and optimized traveling wave control method. As a numerical example, three strategies of independent mode space control, traditional traveling wave control and optimized traveling wave control are used to control the active vibration of the beam angle. By comparing the numerical results of the three methods, it can be seen that: the traditional mode space control method has good effect on the low-frequency control, but it is easy to overflow because of omitting the high-order modes.
(2)
Traveling wave control can effectively control the high-order modes of the system, while the effect of low-order mode control is far less than that of modal control. In addition, the application position of wave control torque has important influence on the control result.
(3)
Using the optimized traveling wave control method and Timoshenko beam theory, the dispersion relationship of waves in structural vibration is determined, and the wave numbers of propagating waves and attenuation waves in the Timoshenko beam are given. The problem of solving the natural frequency and mode of the cantilever Timoshenko beam is effectively solved. The optimized traveling wave control method involves using the traveling wave control outside the modal nodes of each order, coupled with the global mode space control method. The optimized traveling wave control method not only effectively suppresses the main low-order modes, but also suppresses the high-order modes by wave control, effectively reduces the control overflow and enhances the robustness of the system.
In this paper, the Timoshenko beam model, which considers the influence of transverse shear deformation and moment of inertia on displacement, improves the accuracy of calculation. It is important for spacecraft accessory structures with high requirements for angle control. In terms of vibration control results, not only the vibration is well suppressed, but also the robustness of the system is improved by using the optimal traveling wave control method proposed in this paper. The optimized traveling wave control method is exquisite in mathematical processing and has good results in global and local vibration control, which is not available in other methods. Therefore, the optimized control method shows better vibration active control performance than any traditional control method.

Author Contributions

Conceptualization, H.J. and C.Z.; methodology, H.J. and B.W.; software, J.F.; validation, H.J., C.Z. and H.D.; formal analysis, J.F.; investigation, W.J. and C.X.; resources, H.D.; writing—original draft preparation, J.F.; writing—review and editing, C.Z.; supervision, H.J and W.Z.; project administration, Y.G.; funding acquisition, W.Z. All authors have read and agreed to the published version of the manuscript.

Funding

This paper is supported by Sichuan Science and Technology Program: 2022YFG0274; Key Research and Development Program of Zhejiang Province: 2021C03013; National Natural Science Foundation of China: 51875146; Natural Science Foundation of Zhejiang Province: LY21E050005; Key Laboratory for Technology in Rural Water Management of Zhejiang Province: ZJWEU-RWM-20200303B.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

The study did not report any data.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Rong, J.L.; Xu, T.F.; Wang, X.; Li, J.; Yin, X.; Xin, P. Dynamic stability analysis of flexible spinning flight vehicles under follower thrust. J. Astronaut. 2015, 36, 18–24. [Google Scholar]
  2. Beck, A.T.; da Silva, C.R.A., Jr. Timoshenko versus Euler beam theory: Pitfalls of a deterministic approach. Struct. Saf. 2011, 33, 19–25. [Google Scholar] [CrossRef]
  3. Li, D.X. Structural Dynamics of Flexible Spacecraft; Science Press: Beijing, China, 2010. (In Chinese) [Google Scholar]
  4. Ruge, P.; Birk, C. A comparison of infinite Timoshenko and Euler-Bernoulli beam models on Winkler foundation in the frequency- and time-domain. J. Sound Vib. 2007, 304, 932–947. [Google Scholar] [CrossRef]
  5. Shafiei, N.; Kazemi, M.; Ghadiri, M. Comparison of modeling of the rotating tapered axially functionally graded Timoshenko and Euler-Bernoulli microbeams. Phys. E Low-Dimens. Syst. Nanostruct. 2016, 83, 74–87. [Google Scholar] [CrossRef]
  6. Sferza, M.; Ninić, J.; Chronopoulos, D.; Glock, F.; Daoud, F. Multidisciplinary Optimisation of Aircraft Structures with Critical Non-Regular Areas: Current Practice and Challenges. Aerospace 2021, 8, 223. [Google Scholar] [CrossRef]
  7. Mei, C.; Mace, B.R.; Jones, R.W. Hybrid wave/mode active vibration control. J. Sound Vib. 2001, 247, 765–784. [Google Scholar] [CrossRef]
  8. Mei, C.; Mace, B.R. Reduction of control spillover in active vibration control of distributed structures using multioptimal schemes. J. Sound Vib. 2002, 251, 184–192. [Google Scholar] [CrossRef]
  9. Carvalho, M.O.M.; Zindeluk, M. Active control of waves in a Timoshenko beam. Int. J. Solids Struct. 2001, 38, 1749–1764. [Google Scholar] [CrossRef]
  10. Halkyard, C.R.; Mace, B.R. Feedforward adaptive control of flexural vibration in a beam using wave amplitudes. J. Sound Vib. 2002, 254, 117–141. [Google Scholar] [CrossRef]
  11. EL-Khatib, H.M.; Mace, B.R.; Brennan, M.J. Suppression of Bending Waves in a Beam Using a Tuned Vibration Absorber. J. Sound Vib. 2005, 288, 1157–1175. [Google Scholar] [CrossRef]
  12. Hu, C.; Chen, T.; Huang, W.H. Active Vibration Control of Timoshenko Beam Based on Hybrid Wave/Mode Method. Acta Aeronaut. Astronaut. Sin. 2007, 28, 301–308. [Google Scholar]
  13. Su, Y.C.; Ma, C.C. Theoretical analysis of transient waves in a simply-supported Timoshenko beam by ray and normal mode methods. Int. J. Solids Struct. 2011, 48, 535–552. [Google Scholar] [CrossRef]
  14. Su, Y.C.; Ma, C.C. Transient wave analysis of a cantilever Timoshenko beam subjected to impact loading by Laplace transform and normal mode methods. Int. J. Solids Struct. 2012, 49, 1158–1176. [Google Scholar] [CrossRef] [Green Version]
  15. Cardoso, R.P.R. A new beam element which blends the Euler-Bernoulli beam theory with idealised transverse shear flows for aircraft structural analysis. Thin-Walled Struct. 2020, 157, 107–118. [Google Scholar] [CrossRef]
  16. Xing, X.Y.; Liu, J.K. Modelling and neural adaptive vibration control for three-dimensional Timoshenko beam with output restrictions and external disturbances. Int. J. Syst. Sci. 2021, 52, 1850–1867. [Google Scholar] [CrossRef]
  17. Ishaquddin, M.; Raveendranath, P.; Reddy, J.N. Flexure and torsion locking phenomena in out-of-plane deformation of Timoshenko curved beam element. Finite Elem. Anal. Des. 2012, 51, 22–30. [Google Scholar] [CrossRef]
  18. Endo, T.; Sasaki, M.; Matsuno, F. Contact-Force Control of a Flexible Timoshenko Arm. IEEE Trans. Autom. Control 2013, 12, 875–882. [Google Scholar] [CrossRef]
  19. Mei, C. Hybrid wave/mode active control of bending vibrations in beams based on the advanced Timoshenko theory. J. Sound Vib. 2009, 322, 29–38. [Google Scholar] [CrossRef]
  20. Pham, P.T.; Kim, G.H.; Hong, K.S. Vibration control of a Timoshenko cantilever beam with varying length. Int. J. Control Autom. Syst. 2022, 20, 175–183. [Google Scholar] [CrossRef]
  21. Eshag, M.A.; Lei, M.; Sun, Y.; Zhang, K. Robust global boundary vibration control of uncertain Timoshenko beam with exogenous disturbances. IEEE Access 2020, 8, 72047–72058. [Google Scholar] [CrossRef]
  22. Fleischmann, D.; Könözsy, L. On a novel approximate solution to the inhomogeneous Euler—Bernoulli equation with an application to aeroelastics. Aerospace 2021, 8, 356. [Google Scholar] [CrossRef]
  23. Chen, X.; Liu, J.; Gao, B.; Chen, X.F. Analysis and implementation of a multiple-source multiple-channel active vibration control of large structures based on finite element model in-loop simulation system. In Proceedings of the 24th International Congress on Sound & Vibration, London, UK, 23–27 July 2017. [Google Scholar]
  24. Liu, C.C.; Li, F.M.; Tang, L.; Huang, W.H. Vibration control of the finite L-shaped beam structures based on the active and reactive power flow. Sci. China Phys. Mech. Astron. 2011, 54, 310–319. [Google Scholar] [CrossRef]
Figure 1. Schematic diagram of wave control in the cantilever Timoshenko beam.
Figure 1. Schematic diagram of wave control in the cantilever Timoshenko beam.
Aerospace 09 00259 g001
Figure 2. Comparison of frequency response before and after modal control ( x d = 0.15 l , x s = 0.265 l ).
Figure 2. Comparison of frequency response before and after modal control ( x d = 0.15 l , x s = 0.265 l ).
Aerospace 09 00259 g002
Figure 3. Comparison of frequency response before and after wave control ( x d = 0.15 l , x w = 0.40 l ).
Figure 3. Comparison of frequency response before and after wave control ( x d = 0.15 l , x w = 0.40 l ).
Aerospace 09 00259 g003
Figure 4. Comparison of frequency response before and after optimized control ( x d = 0.15 l ).
Figure 4. Comparison of frequency response before and after optimized control ( x d = 0.15 l ).
Aerospace 09 00259 g004
Figure 5. Comparison of frequency response before and after modal control ( x d = 0.10 l , x s = 0.295 l ).
Figure 5. Comparison of frequency response before and after modal control ( x d = 0.10 l , x s = 0.295 l ).
Aerospace 09 00259 g005
Figure 6. Comparison of frequency response before and after wave control ( x d = 0.10 l , x w = 0.30 l ).
Figure 6. Comparison of frequency response before and after wave control ( x d = 0.10 l , x w = 0.30 l ).
Aerospace 09 00259 g006
Figure 7. Comparison of frequency response before and after optimized control ( x d = 0.10 l ).
Figure 7. Comparison of frequency response before and after optimized control ( x d = 0.10 l ).
Aerospace 09 00259 g007
Table 1. The first 10 dimensionless frequency of the Timoshenko beam.
Table 1. The first 10 dimensionless frequency of the Timoshenko beam.
Order of Mode12345678910
natural frequency1.006.0215.9929.3545.3463.3482.98104.02126.30149.59
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Ji, H.; Zhou, C.; Fan, J.; Dai, H.; Jiang, W.; Gong, Y.; Xu, C.; Wang, B.; Zhou, W. Angular Displacement Control for Timoshenko Beam by Optimized Traveling Wave Method. Aerospace 2022, 9, 259. https://doi.org/10.3390/aerospace9050259

AMA Style

Ji H, Zhou C, Fan J, Dai H, Jiang W, Gong Y, Xu C, Wang B, Zhou W. Angular Displacement Control for Timoshenko Beam by Optimized Traveling Wave Method. Aerospace. 2022; 9(5):259. https://doi.org/10.3390/aerospace9050259

Chicago/Turabian Style

Ji, Huawei, Chuanping Zhou, Jiawei Fan, Huajie Dai, Wei Jiang, Youping Gong, Chuzhen Xu, Ban Wang, and Weihua Zhou. 2022. "Angular Displacement Control for Timoshenko Beam by Optimized Traveling Wave Method" Aerospace 9, no. 5: 259. https://doi.org/10.3390/aerospace9050259

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop