Next Article in Journal
Editorial
Previous Article in Journal
Deep PCA-Based Incipient Fault Diagnosis and Diagnosability Analysis of High-Speed Railway Traction System via FNR Enhancement
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

A Continuous Production Apparatus for a Frame-Type Melt-Blown Filter Cartridge with Various Properties and Geometry

1
Department of Mechanical Design Engineering, National Formosa University, Huwei Township 632, Taiwan
2
Smart Machine and Intelligent Manufacturing Research Center, National Formosa University, Huwei Township 632, Taiwan
*
Author to whom correspondence should be addressed.
Machines 2023, 11(4), 476; https://doi.org/10.3390/machines11040476
Submission received: 13 February 2023 / Revised: 6 April 2023 / Accepted: 10 April 2023 / Published: 13 April 2023
(This article belongs to the Section Industrial Systems)

Abstract

:
Polypropylene (PP) melt-blown (MB) filter cartridges are widely used in many fields requiring water purification, such as households, the food industry, industrial processes, and recycled water filtration. While the demand for filters has gradually increased, the environmental requirements and conditions have become severe. The filters are easily deformed from higher liquid pressure during operation and setup and need to be replaced frequently. With the lifetime of filters shortened, manpower increases to replace filters. Hence, the inner structure of a PP melt-blown filter cartridge is supported by a frame structure to resist higher liquid pressure for enhancing filtration efficiency and lifetime. The filter, known as a “frame-type melt-blown filter cartridge”, does not affect the user’s application environment and equipment. This article focuses on developing continuous production equipment for frame-type melt-blown filter cartridges. The core technology of the equipment is the mechanism design for conveying frame tubes integrated with the MB process. The PP fiber is simultaneously melted and blown on the frame tube, and the frame tube needs to be pushed forward while rotating. This mechanism can independently control the fiber’s rotational speed and push speed. The rotational speed affects the surface density, fiber diameter, and porosity of the melt-blown filter cartridge, and the push speed affects the core diameter and weight of the melt-blown filter cartridge. In addition, there is a frame tube feeding device at the input end of the conveying equipment for continuously carrying the frame tube. Then, the finally formed melt-blown filter cartridges enter the cutting machine to trim a certain length to complete a frame-type melt-blown filter cartridge. The complexity of the operation is simplified by a human–machine interactive interface. A programmable logic controller (PLC) and a LabVIEW human–machine interactive interface are used to dominate the equipment. The Modbus communication protocol is adopted for connecting and communicating between PLC and LabVIEW. The interface can integrate and analyze the process data, including overall equipment effectiveness (OEE), total effective equipment performance (TEEP), loading time, utilization, performance, and yield. The entire production process of the frame-type melt-blown filter cartridge is optimized, and the traditional output of 1000 per day is upgraded to 1300. Overall, the processing speed is increased by up to 30%.

1. Introduction

Melt blowing is a versatile, extrusion-based, nonwoven fabrication method of micro and nanofibers where a polymer melt is extruded through small nozzles surrounded by high-speed blowing gas. These fibers are collected in a single process of polymer fiber spinning, air quenching/drawing, and web formation. During the melt-blown (MB) process, the polymer is melted and pushed forward by an extruder and ultimately reaches the spinning head. The polymer melt is drawn into filaments by high-speed hot air. The fibers’ diameters typically range from 1 to 10 µm in the MB process, and their average diameter is generally 1–2 µm [1]. The melt-blown fabric possesses high surface area per unit weight, high barrier properties, and high production efficiency compared with other fine-fiber forming techniques [2,3,4,5,6]. In addition, melt blowing is a solvent-free process that makes it economically and environmentally friendly. It is always desirable to further reduce fiber diameter to improve filtration efficiency. Melt-blown fabrics are widely applied in various fields, especially in the fight against the COVID-19 pandemic as the filtration media in face masks [7,8]. Moreover, the polymer fibers are also fabricated to various types of filter cartridges by spinning machines. The filter cartridge is used to form tubular filtration equipment or an array of filtration requirements in different industries, and is adopted to remove unwanted particles, pollutants, and chemicals from liquids. The filter cartridges are available in various lengths and diameters, which require a strong core to be able to handle the increased pressure differential during operation because the liquid flow is outside-to-inside. Some manufacturers have outer cages for increased stability and capacities. The filter cartridges are installed in pressure vessels with guide rods for easy installation. High-capacity filter cartridges are designed to have increased filter area based upon pleated configuration, flow channels, and flow chambers. The benefits are increased filter area in small housings when there are space constraints and other process requirements [9]. In addition, the water filter is the most important part of a reverse osmosis (RO) system or water purification system. A high-quality filter helps remove impurities effectively up to 99%.
The filtration efficiency of MB fabrics is related to the geometric dimensions of the fiber, thickness (or diameter), porosity (or packing density), structure, and other influential factors, including the nature of the aerosol, the particle size, and environmental conditions such as temperature, relative humidity, and air velocity (air permeability or resistance). Pore size is a critical factor affecting filtration efficiency and is directly related to the fiber diameter, the solidity (packing density), and the thickness (or diameter) of fabrics. Solidity is the volume of fibers per unit volume of fabric, which depends on the fiber diameter and geometry within fibrous structures (fiber mat or cartridge). The porosity of the fabric can be calculated by the mass–density method.
Vfiber = M/D
where M is the mass of the fiber (g), D is the density of the polymer (g/cm3), and Vfiber is the absolute volume of the fiber in the fabric (cm3);
Vfabric = W × L × t = π × (Ro2 − Ri2) × H
where W is the width (cm) of the fabric, L is the length (cm) of the fabric, t is the thickness (cm) of the fabric measured at a specified pressure, Ro is the outer radius of the filter cartridge, Ri is the internal radius of the filter cartridge, H is the height of the filter cartridge, and Vfabric is the bulk volume (cm3) of the fabric. Pfabric is the porosity of the fabric [10].
Pfabric = (Vfabric − Vfiber)/Vfabric × 100%
Polypropylene (PP), with the property of easy processing, is widely used in a filter medium, which possesses low density, hydrophobic, good chemical stability, low melt temperatures for easy bonding, and good mechanical strength. PP polymer can generate the tiniest fibers compared to other polymers using MB technology [11]. In addition, the molecular weight associated with the melt flow index (MFI) [g/10 min] must be suitable under an optimal melt temperature. Moreover, the filtration efficiency can be less than 0.3 μm using the optimal processing parameters. Using MB, some essential filtration efficiency of the polymer fiber is reported on the related factors, including material, average fiber diameter, average pore size, porosity, and pressure drop (loading speed). Hence, the filtration efficiency can be controlled by processing parameters [11,12,13,14,15,16,17,18,19,20]. In addition, PP has been used to produce carbon fiber-filled thermoplastic pellets by an extrusion and pultrusion system [21]. The Multi Jet Fusion (MJF) technology was adopted to fabricate the samples of polypropylene (PP), thermoplastic polyurethane (TPU), and polyamide 11 (PA11). A surface roughness study was performed on these samples to examine the placement and orientation of 3D objects while printing. The TPU samples have a surface roughness much higher than the PP and PA11 ones. The surfaces printed vertically (along the Z-axis) tend to be less smooth. This was consistent with the surfaces of objects made of TPU located in the central zones of the print chamber during printing [22].
A perfect filtration system needs multi-filter cartridges with various porosities to enhance the lifetime of filter cartridges and reduce filtration resistance. Although melt-blown filter cartridges with nanofibers can enhance filtration performance through certain methods, including the one-step melt-blown technique and islands-in-the-sea approach [23,24], these methods have some weaknesses, including increasing filtration resistance and energy consumption [25].
This article focuses on developing a continuous production apparatus of frame-type melt-blown filter cartridges with multi-porosity. However, a loosened filter cartridge with a low density is hardly produced through the MB process because a loosened structure cannot easily form a filter cartridge. Furthermore, a loosened filter cartridge with a soft structure hardly sustains a high liquid pressure for further reducing applications. Although the frame tube is often used to support the filter cartridge, it is quickly and manually inserted into the center of the filter cartridge using the principle of thermal expansion and contraction after the filter cartridge without the frame tube is fabricated by the MB process. Noteworthily, this method results in some deficiencies. First, the frame tube is not essentially merged with the polymer fibers during the MB process. Second, a loosened filter cartridge with a low density cannot be formed easily without the frame tube during the MB process. Third, the frame tube is assembled in the filter cartridge during the MB process by the fused bonding effect, which can hardly sustain high liquid pressure. Nevertheless, these deficiencies can be ameliorated by developing a continuous production apparatus of frame-type melt-blown filter cartridges. In short, this equipment mainly uses the fused bonding effect to merge the frame tube with PP polymer fibers during the MB process for uninterruptedly forming frame-type melt-blown filter cartridges.

2. Materials and Methods

The traditional frameless melt-blown filter cartridge equipment comprises a melt-blown system and a driving mechanism system. The melt-blown system is a commercial product. This system can generate fine PP fibers under certain parameters and recipes, including raw material (polymer), melt flow index (MFI), melt temperature, air pressure (air flow rate or air velocity), polymer flow rate (extruder screw speed), DCD (die-to-collector distance), and the design of the melt-blowing die head. The proposed study focuses on developing a novel driving mechanism system to continue and deliver the frame tubes to integrate them further with the commercial melt-blown system. The novel continuous production apparatus of frame-type melt-blown filter cartridges is schematically shown in Figure 1. On the other hand, a three-dimensional computer graphics of the machine is shown in Figure 2. The novel driving mechanism system comprises two propelling movement sets—a feeder set and a trimming set.
The feeder set controls and delivers the frame tubes to the production axis line at the input end of the propelling movement set. The feeder set consists of an adjustable stockpiling tray, a blocking plate, a pencil cylinder, and a connection mechanism, as shown in Figure 3. The adjustable stockpiling tray is used to store the frame tubes, which can be adjusted to the frame tube’s various lengths. The blocking plate is used to obstruct the frame tube to avoid contact with each other when the frame tube falls to the production axis line. The pencil cylinder is used to extrude the frame tube forward to connect the previous frame tube when the head of the pencil cylinder can passively rotate with the frame tube, as shown in Figure 4. The connection mechanism using a cone pipe is adopted to align the frame tube with the previous frame tube. This mechanism is designed as a semi-open cone pipe to facilitate the observation of the butting situation between the frame tubes, as shown in Figure 5. A proximity sensor is adopted to confirm the frame tube continually and engage with the previous frame tube.
Two propelling movement sets periodically convey the frame tubes with two movements of push forward and rotation, as shown in Figure 6. The propelling movement set can individually control the rotational speed (unit: RPM) and the push-forward speed (unit: mm/min) in the frame tubes. The rotational speed of the frame tube affects the density (porosity) of melt-blown filter cartridges, and the push-forward speed of the frame tube affects the diameter and weight of melt-blown filter cartridges. A three-dimensional computer graphics of the propelling movement set is shown in Figure 7. In a typical parameter, both propelling movement sets alternate in pushing forward slowly with a linear speed of 10 mm/s and pulling backward rapidly with a linear speed of 80 mm/s. The time flow chart of two propelling movement sets is shown in Figure 8. The propelling movement set is pushed forward within 40 s and pulled backward within 5 s. The whole cycle of the propelling movement set is 47 s. The interval between both propelling movement sets is 23.5 s. Each propelling movement set can grip or release the frame tubes with various diameters by a pair of pneumatic cylinders, as shown in Figure 9. Furthermore, there is a pair of rubber rollers to drive the frame tubes with a rotational speed when the pair of pneumatic cylinders is an actuator to grip the frame tubes. In addition, two pairs of pneumatic cylinders and rubber rollers are settled on a sliding table for a linear movement to push forward in gripping the frame tube or pull backward in releasing the frame tube. The sliding table is slowly moved forward when two pairs of pneumatic cylinders and rubber rollers are activated, resulting in rotation and push-forward speeds in the frame tube. However, the pair of pneumatic cylinders is not activated, rapidly pulling the slide table backward upon releasing the frame tube. The pair of rubber rollers grip the frame tube to generate a rotational speed. The selection of the rubber roller is a crucial step; the hardness and thickness of the rubber roller can result in better contact with the uneven frame tube. The properties and dimensions of the rubber roller are shown in Table 1. Furthermore, a pair of auxiliary support rollers are employed to hold the frame tube on the production axis line when the frame tube is rotated and pushed forward. The auxiliary support roller needs a sleek surface to reduce friction to the frame tube. The properties and dimensions of the auxiliary support roller are shown in Table 2.
The trimming set is adopted to control the length of the filter cartridge, comprising a pair of auxiliary support rollers, a slide, an amputator, and a pneumatic cylinder, as shown in Figure 10. The pair of auxiliary support rollers are adopted to provide firm support during the trimming process of the filter cartridge. The pneumatic cylinder is used to hold and align the filter cartridge with the production axis line. Further, the head of the pneumatic cylinder can passively rotate with the filter cartridge. The position of the pneumatic cylinder can also be adjusted to produce the various lengths of the filter cartridge, as shown in Figure 11. The slider carries the pneumatic cylinder, the auxiliary device, and the amputator to move forward to produce a certain length of the filter cartridge. Then, the amputator implements the trimming process of the filter cartridge. Subsequently, the pneumatic cylinder is pushed backward, allowing the filter cartridge to fall into a catch tray. The amputator uses a disc blade with a high-speed rotation to trim the filter cartridges. When the slide touches a trigger sensor, the amputator is activated to trim the filter cartridge, and it accelerates backward to return, as shown in Figure 12. Moreover, the amputator is moved to trim the filter cartridge by a pneumatic cylinder.
The novel continuous production apparatus of frame-type melt-blown filter cartridges is controlled by a MITSUBISH Programmable Logic Controller (PLC, FX3U-32M) and a LabVIEW human–machine interactive interface. The communication between PLC and LabVIEW is achieved by a Modbus RTU transmission mode. The LabVIEW system at the PC (personal computer) end is used as a master mode, and the PLC end is used as a slave mode. A communication module of 485ADP-MB is configured on the PLC end. Then, the LabVIEW project module of Modbus-LabVIEW-Library is configured on the PC end.
The transmission line of RS-485 to USB is adopted to connect both ends. With the advantage of LabVIEW human–machine interactive interface, the interface can continuously capture and record the controlled data from the PLC end, which can integrate and analyze the process data, including overall equipment effectiveness (OEE), total effective equipment performance (TEEP), loading time, utilization, performance, and yield. The home screen of the LabVIEW human–machine interactive interface is shown in Figure 13.

3. Results and Discussions

A general melt-blown filter cartridge is a hollow cylindrical structure. The liquid flow enters the filter cartridge from the outer layer into the inner layer (namely outside-to-inside). Therefore, the filter cartridge requires a strong core to be able to brace the increased liquid pressure differential during operation [9]. The outer cages are often used to increase stability and capacities. The guide rods are adopted to facilely install the filter cartridges in pressure vessels. The O-ring is often used to seal the filter cartridge to vessels. It is favorable to increase the filter area based on some designs such as the pleated configuration, multi-flow channels, and flow chambers to achieve high-capacity filter cartridges. The structure of multi-channel and -chamber systems consists of various densities, filter media, structures, textures, and materials of filter cartridges. The filter cartridges with various densities applied to the design of multi-channel and -chamber filtration systems can extend their lifetime. A filter cartridge with a lower density can capture the larger unwanted particles, pollutants, and chemicals from liquids. On the contrary, a filter cartridge with a higher density can capture the smaller unwanted particles, pollutants, and chemicals from liquids. It is easy to fabricate a filter cartridge with a higher density due to the sturdy and dense structure of the MB polymer. However, it is difficult to fabricate a filter cartridge with a lower density due to the loose and feeble structure of the MB polymer. Therefore, the continuous production apparatus of frame-type melt-blown filter cartridges is an advantage to fabricating filter cartridges with various densities, diameters, and lengths. Hence, frame tubes in melt-blown filter cartridges provide at least two benefits. First, frame-type melt-blown filter cartridges can effectively resist the higher liquid pressure. Second, the loose and feeble MB polymer can be constructed on the frame tubes to form the filter cartridges. In general, the frame tubes are inserted into the center of the filter cartridges after the frameless MB filter cartridges are fabricated in advance. This manufacture method causes a serious problem because the MB polymer is not authentically merged with the frame tube. Further, the MB polymer can easily cause a distortion or deformation that further impairs the capability or function of the filter cartridges when a higher liquid pressure is applied to them. Hence, PP polymer fibers are merged with the frame tubes during the MB process, which can strengthen the filter cartridges for enduring various liquid pressure differentials.
The commercial frame tube is adopted to produce the filter cartridge. The properties of the frame tube are shown in Table 3, and the entity graph of the commercial frame tube is shown in Figure 14. The parameters for generating fine PP fibers in the commercial melt-blown system are shown in Table 4. The melt-blowing die head in the commercial melt-blown system is shown in Figure 15. Figure 16 shows the fabricated continuous production apparatus of frame-type melt-blown filter cartridges. Figure 17 shows fine PP fibers melt-blown on the frame tube. Further, Figure 18 shows the fabricated frame-type melt-blown filter cartridge in the trimming set. This apparatus has been validated to produce various lengths, densities, and porosities of frame-type melt-blown filter cartridges, as shown in Figure 19. The fabricated frame-type melt-blown filter cartridges with two very different densities are shown in Table 5. The manufacturing parameters of the filter cartridges will vary depending on the polymer specification, chemical properties, and production environment such as temperature, humidity, and other factors. The low-density melt-blown filter cartridge is successfully produced on the frame tube, which is not manufactured by traditional equipment. All in all, traditional frameless melt-blown filter cartridge equipment has some shortcomings, including that the density (porosity) and the diameter of melt-blown filter cartridges are not individually controlled. Although the high-density frameless melt-blown filter cartridge is a mature technology, the low-density frameless melt-blown filter cartridge presents a loose structure without support that can hardly sustain a higher liquid pressure. A perfect filtration system needs multi-filter cartridges with various porosities to enhance the lifetime of filter cartridges and reduce filtration resistance. In the proposed design, the propelling movement set can individually control the rotational speed and the push-forward speed in the frame tubes. The rotational speed of the frame tube affects the density (porosity) of melt-blown filter cartridges, and the push-forward speed of the frame tube affects the diameter and weight of melt-blown filter cartridges. Furthermore, PP polymer fibers are sturdily merged with the frame tubes during the MB process. This is the main purpose of the study—to develop continuous production equipment for frame-type melt-blown filter cartridges.
During the production process, the human–machine interactive interface continuously monitors the real-time production quantity, utilization, performance, yield, operation time, and frequency of the devices (motors and pneumatic cylinders), and the status of the equipment. An Excel file report can be produced to record and retrospect the production information, which can be issued to improve production efficiency, as shown in Figure 20. Moreover, the human–machine interactive system can also supply an efficient and clear operation interface. The interface has two modes including automatic and manual operation. The manual operation mode is used for pre-production and pre-loading, then the automatic operation mode is used for automatic production and to return original assignments. The input data of the interface include batch number, specification of filter cartridge, length of filter cartridge, production target, and specification of frame tube. The dynamic and static illustration are adopted to present the current equipment operating status. Furthermore, the wear database of the components is built for monitoring the lifetime of devices including pneumatic cylinders, motors, amputators, and the cumulative moving distance of slide tables. The proposed apparatus can contend with the conditions as follows:
  • The low-density melt-blown filter cartridge can easily result in a collapse during the MB process. A loosened structure with fine PP fibers is solidified on the frame tube, which can be achieved by the proposed apparatus integrated with the MB process.
  • The traditional PP melt-blown filter cartridge equipment uses a threaded rod to push the filter cartridge forward. However, PP fibers are too tiny and can easily become stuck on the threaded rod. Hence, the filter cartridge is hardly pushed forward, which means that a high-precision filter cartridge cannot be fabricated by traditional equipment. The proposed apparatus can effortlessly merge tiny PP fibers with the frame tube. Further, the frame-type filter cartridge is pushed forward, which is not affected by the geometric dimensions of the fiber.
  • The length of the frame tube must conform to the length of the specified filter cartridge in the traditional equipment. If the length of the filter cartridge is changed, the frame tube must be repurchased or cut shorter in the traditional process. The proposed apparatus cannot be limited by the length of the filter cartridge and the frame tube.
  • The frame-type melt-blown filter cartridge can withstand higher liquid pressure.
  • The proposed apparatus possesses easy operation and simple production steps, further reducing human resources and improving production efficiency.
Figure 20. An Excel file report to record and retrospect the production information: (a) pressing a button in the interface to produce the report; (b) presenting the content of the Excel file.
Figure 20. An Excel file report to record and retrospect the production information: (a) pressing a button in the interface to produce the report; (b) presenting the content of the Excel file.
Machines 11 00476 g020

4. Conclusions

A continuous production equipment for frame-type melt-blown filter cartridges is developed to widely enhance their applications. A recent mechanism is designed for conveying frame tubes integrated with the MB process while the frame tube is pushed forward with rotating. Both the fiber’s rotational speed and push speed are independently controlled to fabricate melt-blown filter cartridges with various surface densities, fiber diameters, porosities, and weight. The proposed equipment has unique features including easily fabricating a low-density melt-blown filter cartridge and various properties, tiny PP fibers effectively merged with the frame tube, facilitating to alter the length of the filter cartridge, strengthening the filter cartridge to withstand higher liquid pressure, and simplifying the operation by a human–machine interactive interface.

Author Contributions

Original draft preparation, C.-C.H.; supervision, C.-C.H.; data curation, C.-H.C. and C.-F.L.; mechanical design, C.-H.C.; electric control, C.-F.L.; methodology, C.-C.H., C.-H.C. and C.-F.L.; visualization, C.-H.C. and C.-F.L. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by local-type project of Small Business Innovation Research (SBIR) from the Taoyuan City Government with grant number 109-005.

Data Availability Statement

The data presented in this study are available from the corresponding author upon reasonable request.

Acknowledgments

The research is supported by CHING-YI Filtration Equipment CO., LTD (Taoyuan City, Taiwan) and the local-type project of Small Business Innovation Research (SBIR) from the Taoyuan City Government. It is necessary to appreciate the president, Kuo-Hwa Chen, and the manager, Ching-Yu Chen, for supplying full assistance in the project execution.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Kim, H.J.; Han, S.W.; Joshi, M.K.; Kim, C.S. Fabrication and characterization of silver nanoparticle-incorporated bilayer electrospun-melt-blown micro/nanofibrous membrane. Int. J. Polym. Mater. Polym. Biomat. 2017, 66, 514–520. [Google Scholar] [CrossRef]
  2. Pu, Y.; Zheng, J.; Chen, F.; Long, Y.; Wu, H.; Li, Q.; Yu, S.; Wang, X.; Ning, X. Preparation of Polypropylene Micro and Nanofibers by Electrostatic-Assisted Melt Blown and Their Application. Polymers 2018, 10, 959. [Google Scholar] [CrossRef] [Green Version]
  3. Hassan, M.A.; Yeom, B.Y.; Wilkie, A.; Pourdeyhimi, B.; Khan, S.A. Fabrication of nanofiber meltblown membranes and their filtration properties. J. Membr. Sci. 2013, 427, 336–344. [Google Scholar] [CrossRef]
  4. Yesil, Y.; Bhat, G.S. Porosity and barrier properties of polyethylene meltblown nonwovens. J. Text. Inst. 2017, 108, 1035–1040. [Google Scholar] [CrossRef]
  5. Brochocka, A.; Majchrzycka, K. Technology for the production of bioactive meltblown filtration materials applied to respiratory protective devices. Fibres Text. East. Eur. 2009, 17, 92–98. [Google Scholar]
  6. Leonas, K.K.; Huang, W. Transmission of small particles through selected surgical gown fabrics. Int. Nonwovens J. 1999, 8, 1558925099OS-800116. [Google Scholar] [CrossRef] [Green Version]
  7. Gereffi, G. What does the COVID-19 pandemic teach us about global value chains? The case of medical supplies. J. Int. Bus. Pol. 2020, 3, 287–301. [Google Scholar] [CrossRef]
  8. Bai, Y.; Yao, L.; Wei, T.; Tian, F.; Jin, D.Y.; Chen, L.; Wang, M. Presumed asymptomatic carrier transmission of COVID-19. JAMA 2020, 323, 1406–1407. [Google Scholar] [CrossRef] [Green Version]
  9. Perlmutter, B.A. Solid-Liquid Filtration-Practical Guides in Chemical Engineering; Elsevier: Amsterdam, The Netherlands, 2015; ISBN 9780128030530. [Google Scholar]
  10. Lei, L.; Qi, D. Study on testing method for porosity of nonwoven fabric. Fiber Test. Garde 2017, 5, 78–80. [Google Scholar]
  11. Kara, Y.; Molnár, K. A review of processing strategies to generate melt-blown nano/microfiber mats for high-efficiency filtration applications. J. Ind. Text. 2022, 51, 137S–180S. [Google Scholar] [CrossRef]
  12. Motyl, E.; Lowkis, B. Effect of air humidity on charge decay and lifetime of PP electret nonwovens. Fibres Text. East. Eur. 2006, 14, 39–42. [Google Scholar]
  13. Xiao, Y.; Sakib, N.; Yue, Z.; Wang, Y.; Cheng, S.; You, J.; Militky, J.; Venkataraman, M.; Zhu, G. Study on the relationship between structure parameters and filtration performance of polypropylene meltblown nonwovens. Autex. Res. J. 2019, 20, 366–371. [Google Scholar] [CrossRef]
  14. Yesil, Y.; Bhat, G.S. Structure and mechanical properties of polyethylene melt blown nonwovens. Int. J. Cloth. Sci. Technol. 2016, 28, 780–793. [Google Scholar] [CrossRef]
  15. Jaganathan, S.; Vahedi Tafreshi, H.; Pourdeyhimi, B. On the pressure drop prediction of filter media composed of fibers with bimodal diameter distributions. Powder Technol. 2008, 181, 89–95. [Google Scholar] [CrossRef]
  16. Bansal, V.; Shambaugh, R.L. On-line determination of diameter and temperature during melt blowing of polypropylene. Ind. Eng. Chem. Res. 1998, 37, 1799–1806. [Google Scholar] [CrossRef]
  17. Hammonds, R.L.; Gazzola, W.H.; Benson, R.S. Physical and thermal characterization of polylactic acid meltblown nonwovens. J. Appl. Polym. Sci. 2014, 131, 40593. [Google Scholar] [CrossRef]
  18. Uppal, R.; Bhat, G.; Eash, C.; Akato, K. Meltblown nanofiber media for enhanced quality factor. Fibers Polym. 2013, 14, 660–668. [Google Scholar] [CrossRef]
  19. Xie, S.; Han, W.; Jiang, G.; Chen, C. Turbulent air flow field in slot-die melt blowing for manufacturing microfibrous nonwoven materials. J. Mater. Sci. 2018, 53, 6991–7003. [Google Scholar] [CrossRef] [Green Version]
  20. Moore, E.M.; Papavassiliou, D.V.; Shambaugh, R.L. Air velocity, air temperature, fiber vibration and fiber diameter measurements on a practical melt blowing die. Int. Nonwovens J. 2004, 13, 43–53. [Google Scholar] [CrossRef] [Green Version]
  21. Budiyantoro, C.; Rochardjo, H.S.B.; Nugroho, G. Design, Manufacture, and Performance Testing of Extrusion–Pultrusion Machine for Fiber-Reinforced Thermoplastic Pellet Production. Machines 2021, 9, 42. [Google Scholar] [CrossRef]
  22. Dzienniak, D. The Influence of the Material Type and the Placement in the Print Chamber on the Roughness of MJF-Printed 3D Objects. Machines 2022, 10, 49. [Google Scholar] [CrossRef]
  23. Deng, N.; Hec, H.; Yana, J.; Zhao, Y.; Ticha, E.B.; Liu, Y.; Kang, W.M.; Cheng, B. One-step melt-blowing of multi-scale micro/nano fabric membrane for advanced air-filtration. Polymer 2019, 165, 174–179. [Google Scholar] [CrossRef]
  24. Soltani, I.; Macosko, C.W. Influence of rheology and surface properties on morphology of nanofibers derived from islands-in-the-sea meltblown nonwovens. Polymer 2018, 145, 21–30. [Google Scholar] [CrossRef]
  25. Cheng, S.; Muhaiminul, A.S.M.; Yue, Z.; Wang, Y.; Xiao, Y.; Militky, J.; Prasad, M.; Zhu, G. Effect of Temperature on the Structure and Filtration Performance of Polypropylene Melt-Blown Nonwovens. Autex Res. J. 2021, 21, 207–217. [Google Scholar] [CrossRef]
Figure 1. The schematic illustration of the novel continuous production apparatus of frame-type melt-blown filter cartridges.
Figure 1. The schematic illustration of the novel continuous production apparatus of frame-type melt-blown filter cartridges.
Machines 11 00476 g001
Figure 2. A three-dimensional computer graphics of the novel continuous production apparatus of frame-type melt-blown filter cartridges.
Figure 2. A three-dimensional computer graphics of the novel continuous production apparatus of frame-type melt-blown filter cartridges.
Machines 11 00476 g002
Figure 3. A three-dimensional computer graphics of the feeder set of the frame tube.
Figure 3. A three-dimensional computer graphics of the feeder set of the frame tube.
Machines 11 00476 g003
Figure 4. The details of the feeder set: (a) the adjusted stockpiling tray, (b) the head of the pencil cylinder passively rotated with the frame tube, and (c) the blocking plate used to separate the frame tubes.
Figure 4. The details of the feeder set: (a) the adjusted stockpiling tray, (b) the head of the pencil cylinder passively rotated with the frame tube, and (c) the blocking plate used to separate the frame tubes.
Machines 11 00476 g004aMachines 11 00476 g004b
Figure 5. The semi-open cone pipe adopted to align and connect the frame tubes.
Figure 5. The semi-open cone pipe adopted to align and connect the frame tubes.
Machines 11 00476 g005
Figure 6. Two propelling movement sets periodically working together: (a) a schematic diagram and (b) a detailed chart.
Figure 6. Two propelling movement sets periodically working together: (a) a schematic diagram and (b) a detailed chart.
Machines 11 00476 g006aMachines 11 00476 g006b
Figure 7. A three-dimensional computer graphics of the propelling movement set: (a) a schematic diagram and (b) a detailed chart.
Figure 7. A three-dimensional computer graphics of the propelling movement set: (a) a schematic diagram and (b) a detailed chart.
Machines 11 00476 g007aMachines 11 00476 g007b
Figure 8. The time flow chart of both propelling movement sets.
Figure 8. The time flow chart of both propelling movement sets.
Machines 11 00476 g008
Figure 9. (a) The pair of pneumatic cylinders to grip or release the frame tubes with various diameters; (b) the pair of rubber rollers to drive the frame tubes with a rotational speed under the pair of pneumatic cylinders activated to grip the frame tubes; (c) a detailed lateral view of the propelling movement set during grip and release of the frame tubes.
Figure 9. (a) The pair of pneumatic cylinders to grip or release the frame tubes with various diameters; (b) the pair of rubber rollers to drive the frame tubes with a rotational speed under the pair of pneumatic cylinders activated to grip the frame tubes; (c) a detailed lateral view of the propelling movement set during grip and release of the frame tubes.
Machines 11 00476 g009aMachines 11 00476 g009b
Figure 10. The trimming set adopted to control the length of the filter cartridge.
Figure 10. The trimming set adopted to control the length of the filter cartridge.
Machines 11 00476 g010
Figure 11. The position of the cylinder adjusted to produce the various lengths of the filter cartridge.
Figure 11. The position of the cylinder adjusted to produce the various lengths of the filter cartridge.
Machines 11 00476 g011
Figure 12. The amputator moving forward to trim the filter cartridge and accelerating backward to return under a trigger sensor touched by the slide: (a) a three-dimensional computer graphics and (b) a detailed lateral view of the amputator during the trimming process.
Figure 12. The amputator moving forward to trim the filter cartridge and accelerating backward to return under a trigger sensor touched by the slide: (a) a three-dimensional computer graphics and (b) a detailed lateral view of the amputator during the trimming process.
Machines 11 00476 g012
Figure 13. The home screen of the human–machine interactive interface.
Figure 13. The home screen of the human–machine interactive interface.
Machines 11 00476 g013
Figure 14. The entity graph of the commercial frame tube (Article: FT/P 02).
Figure 14. The entity graph of the commercial frame tube (Article: FT/P 02).
Machines 11 00476 g014
Figure 15. The design of the melt-blowing die head: (a) a schematic illustration of a lateral view of the die head, (b) an entity graph of the die, and (c) fine PP fibers produced by the die head.
Figure 15. The design of the melt-blowing die head: (a) a schematic illustration of a lateral view of the die head, (b) an entity graph of the die, and (c) fine PP fibers produced by the die head.
Machines 11 00476 g015
Figure 16. The fabricated continuous production apparatus of frame-type melt-blown filter cartridges: (a) the front end, including the feeder set and two propelling movement sets; (b) the rear end, including the trimming set.
Figure 16. The fabricated continuous production apparatus of frame-type melt-blown filter cartridges: (a) the front end, including the feeder set and two propelling movement sets; (b) the rear end, including the trimming set.
Machines 11 00476 g016
Figure 17. Fine PP fibers essentially merged with the frame tube during the MB process.
Figure 17. Fine PP fibers essentially merged with the frame tube during the MB process.
Machines 11 00476 g017
Figure 18. The fabricated frame-type melt-blown filter cartridge before the trimming process.
Figure 18. The fabricated frame-type melt-blown filter cartridge before the trimming process.
Machines 11 00476 g018
Figure 19. The fabricated frame-type melt-blown filter cartridge with (a) various lengths and (b) densities.
Figure 19. The fabricated frame-type melt-blown filter cartridge with (a) various lengths and (b) densities.
Machines 11 00476 g019
Table 1. The specification sheet of the rubber roller.
Table 1. The specification sheet of the rubber roller.
Model Number: ROLNAH50-T10-15-L200
ItemValueItemValue
MaterialPolyurethane (PU)FabricationIncrusted type
Thickness (mm)10Roller formStraight cylinder
Outer diameter of Metal tube (mm)50Length (mm)200
Inner diameter of Metal tube (mm)15Hardness50
Table 2. The specification sheet of the auxiliary support roller.
Table 2. The specification sheet of the auxiliary support roller.
Model Number: HRO57-263
ItemValueItemValue
MaterialSteelSurface treatmentGalvanization
Thickness (mm)10FormLong roller for conveyor belt
Outer diameter (mm)57.2Length (mm)263
Table 3. The commercial frame tube used to produce the filter cartridge.
Table 3. The commercial frame tube used to produce the filter cartridge.
Article: FT/P 02
ItemValueItemValue
Length (mm)200Pitch (mm)6
PolymerhPPMesh (mm)3.5
Inner diameter (mm)29Weight (g/m)110
Outer diameter (mm)35Open surface (%)39
Thickness (mm)3
Table 4. The parameters for generating fine PP fibers in the melt-blown system.
Table 4. The parameters for generating fine PP fibers in the melt-blown system.
ItemValueItemValue
PolymerPPDCD (die-to-collector distance)30 cm
Rotational speed (RPM)40Push forward speed (mm/s)10
Table 5. The fabricated frame-type melt-blown filter cartridges with two very different densities.
Table 5. The fabricated frame-type melt-blown filter cartridges with two very different densities.
TypeHigh DensityLow Density
Density175.0 kg/m387.4 kg/m3
DCD (die-to-collector distance)20~25 cm25~30 cm
Collector rotary speed1500~1800 RPM1700~1900 RPM
Spinneret throughput0.5 g/min/hole0.3 g/min/hole
AppearanceMachines 11 00476 i001Machines 11 00476 i002
Torn fiber stateMachines 11 00476 i003Machines 11 00476 i004
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Chen, C.-H.; Lee, C.-F.; Hsiao, C.-C. A Continuous Production Apparatus for a Frame-Type Melt-Blown Filter Cartridge with Various Properties and Geometry. Machines 2023, 11, 476. https://doi.org/10.3390/machines11040476

AMA Style

Chen C-H, Lee C-F, Hsiao C-C. A Continuous Production Apparatus for a Frame-Type Melt-Blown Filter Cartridge with Various Properties and Geometry. Machines. 2023; 11(4):476. https://doi.org/10.3390/machines11040476

Chicago/Turabian Style

Chen, Ching-Hao, Ci-Fan Lee, and Chun-Ching Hsiao. 2023. "A Continuous Production Apparatus for a Frame-Type Melt-Blown Filter Cartridge with Various Properties and Geometry" Machines 11, no. 4: 476. https://doi.org/10.3390/machines11040476

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop